Search NASA⌕ Search

SEARCH · Search NASA

Results for “Plant development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Statistical Correlation of Heliostat Pointing Deviation With Wind

This work was carried out as part of the Heliostat Consortium (HelioCon) Field Deployment subtask with the aim to develop a reduced order model framework for correlating wind speed and pointing deviation of a heliostat facet. There are only sparse field measurements of heliostat pointing deviations and accompanying wind conditions published in the literature. Heliostat test standards, such as IEC 62862-4-3, propose a suite of tests including laser pointing repeatability at wind speeds below 4 m/s, and provide technical requirements for heliostat slope and tracking deviations in coarse average wind speed bins of 4 m/s, 6 m/s, and 8 m/s. In addressing the gap of the variation of heliostat pointing deviation with wind speed, field measurements of laser pointing on a grid target and wind conditions were analyzed in this study at the Third-Party Metrology Platform at the National Laboratory of the Rockies (NLR) Flatirons Campus. Horizontal pointing deviations were found to follow a logarithmic relationship with peak wind speed, whereas vertical pointing deviations follow an exponential relationship with peak wind speed. Both horizontal and vertical pointing deviations also follow a second order polynomial relationship, as expected from the proportionality of elastic loads and deformations with the square of wind speed. The results indicate that heliostat facet pointing deviations in the vertical direction increase at a faster rate than in the horizontal direction with increasing wind speed over the tested range, however these are dependent on the heliostat structural design. Next steps are recommended for additional field measurements to confirm a linear relationship of pointing deviation with applied moment on a heliostat facet, and to distinguish between gravity-induced and wind-induced pointing deviations at different elevation angles. The derived correlations in the preliminary analysis in this report serve as a case study for heliostat developers and plant operators to estimate the wind-induced pointing deviations and their variation with peak gust wind speed. Next steps in future work would recommend higher resolution and longer duration datasets for different elevation angles and wind directions to reduce uncertainties and variance of collected laser beam spot data and their correlations with bin-averaged wind speed.

17 WIND ENERGY↗
DOE OSTI2025

Sorghum bicolor BTx623 Nitrogen Grown Conditions Gene Expression Profiling

Dhurrin, a cyanogenic glucoside, plays an important role in Sorghum bicolor physiology and defense. The concentration of dhurrin in sorghum is influenced by both nitrogen status and stage of plant organ development. While nitrogen resupply activates the expression of genes for dhurrin biosynthesis, the molecular mechanisms underlying this regulation remain unclear. In this study, we investigated the transcriptional response of sorghum to nitrogen resupply following growth under nitrogen-limiting conditions. Using a time-course design, we measured hydrogen cyanide potential (HCNp), growth, and nitrate content at 0-, 2-, 6-, 12-, 24-, 36-, 48-, and 60-h after resupply and collected tissue for RNAseq analysis in parallel for analysis of gene expression and construction of gene regulatory networks (GRNs). HCNp (mg g−1 DW) increased significantly in leaf and stem tissues following nitrogen resupply, with increases in the leaf partially driven by continued declines in controls under ongoing nitrogen stress. Expression of the dhurrin pathway genes was upregulated in leaves from 24 h after nitrogen resupply, with diel expression patterns observable over the remaining time points. No upregulation was observed in roots or stems, suggesting that developmental context overrides environmental cues. GRN analysis identified candidate transcription factors regulating dhurrin biosynthesis genes, including members of the MYB, bZIP, and GARP-type transcription factor families. Some of these candidate transcription factors may be involved in relieving senescence-associated suppression of dhurrin biosynthesis and link nitrogen signaling to pathway activation. These findings provide new insight into the nitrogen-responsive regulation of dhurrin in sorghum, highlighting candidate regulators for future functional characterization.

cyanogenic glucoside↗
DOE OSTI2024

Sorghum bicolor BTx623 Nitrogen Grown Conditions Set2 Gene Expression Profiling

Dhurrin, a cyanogenic glucoside, plays an important role in Sorghum bicolor physiology and defense. The concentration of dhurrin in sorghum is influenced by both nitrogen status and stage of plant organ development. While nitrogen resupply activates the expression of genes for dhurrin biosynthesis, the molecular mechanisms underlying this regulation remain unclear. In this study, we investigated the transcriptional response of sorghum to nitrogen resupply following growth under nitrogen-limiting conditions. Using a time-course design, we measured hydrogen cyanide potential (HCNp), growth, and nitrate content at 0-, 2-, 6-, 12-, 24-, 36-, 48-, and 60-h after resupply and collected tissue for RNAseq analysis in parallel for analysis of gene expression and construction of gene regulatory networks (GRNs). HCNp (mg g−1 DW) increased significantly in leaf and stem tissues following nitrogen resupply, with increases in the leaf partially driven by continued declines in controls under ongoing nitrogen stress. Expression of the dhurrin pathway genes was upregulated in leaves from 24 h after nitrogen resupply, with diel expression patterns observable over the remaining time points. No upregulation was observed in roots or stems, suggesting that developmental context overrides environmental cues. GRN analysis identified candidate transcription factors regulating dhurrin biosynthesis genes, including members of the MYB, bZIP, and GARP-type transcription factor families. Some of these candidate transcription factors may be involved in relieving senescence-associated suppression of dhurrin biosynthesis and link nitrogen signaling to pathway activation. These findings provide new insight into the nitrogen-responsive regulation of dhurrin in sorghum, highlighting candidate regulators for future functional characterization.

cyanogenic glucoside↗
NASA NTRS1973

Development of germ-free plants and tissue culture

The botanical program is reported for experiments performed at the Lunar Receiving Laboratory. Papers prepared during this program are listed. The studies reported include: tissues cultured on various mediums, nutritional studies, preparation of plant cultures for Apollo 15, and pine tissue cultures.

Venketeswaran, S.↗
NASA NTRS1973

Synthesis of optically clear polymeric materials for high temperature windows

A polymer has been developed that has excellent potential for use as windows in spacecraft as well as conventional aircraft. This polymer, phenolphthalein polycarbonate, has outstanding thermal properties, e.g., in place of melting or burning, it produces an insulating charred foam that closes off transmission of radiant heat through the window. This fact, coupled with an oxygen index of 0.43 and a 177 C tensile strength of 58 mega Newtons/sq m, makes this polymer a prime candidate for further development. Pilot plant preparation in a 20 gallon Pfaudler kettle was accomplished and large test specimens were prepared for evaluations.

Pannell, C. E.↗
NASA NTRS1978

The role of cell membranes in the regulation of lignification in pine cells

The identity of pine cell membranes bearing PAL enzyme activity, the isolation of a plasma membrane preparation from pine cells for testing as a regulatory barrier in lignification, and the measurement of the geopotential effect in pine stems are presented. A model to describe and predict the interaction of gravity and lignification of higher plants was developed.

Hendrix, D. L.↗
NASA NTRS2003

Durability of Membrane Electrode Assemblies (MEAs) in PEM Fuel Cells Operated on Pure Hydrogen and Oxygen

Proton exchange membrane (PEM) fuel cells are energy sources that have the potential to replace alkaline fuel cells for space programs. Broad power ranges, high peak-to-nominal power capabilities, low maintenance costs, and the promise of increased life are the major advantages of PEM technology in comparison to alkaline technology. The probability of PEM fuel cells replacing alkaline fuel cells for space applications will increase if the promise of increased life is verified by achieving a minimum of 10,000 hours of operating life. Durability plays an important role in the process of evaluation and selection of MEAs for Teledyne s Phase I contract with the NASA Glenn Research Center entitled Proton Exchange Membrane Fuel cell (PEMFC) Power Plant Technology Development for 2nd Generation Reusable Launch Vehicles (RLVs). For this contract, MEAs that are typically used for H2/air operation were selected as potential candidates for H2/O2 PEM fuel cells because their catalysts have properties suitable for O2 operation. They were purchased from several well-established MEA manufacturers who are world leaders in the manufacturing of diverse products and have committed extensive resources in an attempt to develop and fully commercialize MEA technology. A total of twelve MEAs used in H2/air operation were initially identified from these manufacturers. Based on the manufacturers specifications, nine of these were selected for evaluation. Since 10,000 hours is almost equivalent to 14 months, it was not possible to perform continuous testing with each MEA selected during Phase I of the contract. Because of the lack of time, a screening test on each MEA was performed for 400 hours under accelerated test conditions. The major criterion for an MEA pass or fail of the screening test was the gas crossover rate. If the gas crossover rate was higher than the membrane intrinsic permeability after 400 hours of testing, it was considered that the MEA had failed the test. Three types of MEAs out of the nine total membranes failed the test. The evaluation results showed that fuel cell operating conditions (current, pressure, stoichiometric flow rates) were the parameters that influenced the durability of MEAs. In addition, the durability test results indicated that the type of membrane was also an important parameter for MEA durability. At accelerated test conditions, the MEAs with casted membranes failed during the 400 hour test. However, the MEAs prepared from the casted membrane with support as well as extruded membranes, both passed the 400h durability test at accelerated operating test conditions. As a result of the MEA accelerated durability tests, four MEAs were selected for further endurance testing. These tests are being carried out with four-cell stacks under nominal fuel cell operating conditions.

Stanic, Vesna↗
NASA NTRS1995

Gravitropic responses of the Avena coleoptile in space and on clinostats. II. Is reciprocity valid?

Experiments were undertaken to determine if the reciprocity rule is valid for gravitropic responses of oat coleoptiles in the acceleration region below 1 g. The rule predicts that the gravitropic response should be proportional to the product of the applied acceleration and the stimulation time. Seedlings were cultivated on 1 g centrifuges and transferred to test centrifuges to apply a transverse g-stimulation. Since responses occurred in microgravity, the uncertainties about the validity of clinostat simulation of weightlessness was avoided. Plants at two stages of coleoptile development were tested. Plant responses were obtained using time-lapse video recordings that were analyzed after the flight. Stimulus intensities and durations were varied and ranged from 0.1 to 1.0 g and from 2 to 130 min, respectively. For threshold g-doses the reciprocity rule was obeyed. The threshold dose was of the order of 55 g s and 120 g s, respectively, for two groups of plants investigated. Reciprocity was studied also at bending responses which are from just above the detectable level to about 10 degrees. The validity of the rule could not be confirmed for higher g-doses, chiefly because the data were more variable. It was investigated whether the uniformity of the overall response data increased when the gravitropic dose was defined as (gm x t) with m-values different from unity. This was not the case and the reciprocity concept is, therefore, valid also in the hypogravity region. The concept of gravitropic dose, the product of the transverse acceleration and the stimulation time, is also well-defined in the acceleration region studied. With the same hardware, tests were done on earth where responses occurred on clinostats. The results did not contradict the reciprocity rule but scatter in the data was large.

Flight Experiment↗
NASA NTRS1996

Identifying yield-optimizing environments for two cowpea breeding lines by manipulating photoperiod and harvest scenario

Photoperiod and harvest scenario of cowpea (Vigna unguiculata L. Walp) canopies were manipulated to optimize productivity for use in future controlled ecological life-support systems. Productivity was measured by edible yield rate (EYR:g m-2 day-1), shoot harvest index (SHI: g edible biomass [g total shoot dry weight]), and yield-efficiency rate (YER:g edible biomass m-2 day-1 per[g nonedible shoot dry weight]). Breeding lines 'IT84S-2246' (S-2246) and "IT82D-889' (D-889) were grown in a greenhouse under 8-, 12-, or 24-h photoperiods. S-2246 was short-day and D-889 was day-neutral for flowering. Under each photoperiod, cowpeas were harvested either for leaves only, seeds only, or leaves plus seeds (mixed harvest). Photoperiod did not affect EYR of either breeding line for any harvest scenario tested. Averaged over both breeding lines, seed harvest gave the highest EYR at 6.7 g m-2 day-1. The highest SHI (65%) and YER (94 mg m-2 day-1 g-1) were achieved for leaf-only harvest of D-889 under an 8-h photoperiod. For leaf-only harvest of S-2246, both SHI and YER increased with increasing photoperiod, but declined for seed-only and mixed harvests. However, photoperiod had no effect on SHI or YER for D-889 for any harvest scenario. A second experiment utilized the short-day cowpea breeding line 'IT89KD-288' (D-288) and the day-neutral breeding line 'IT87D-941-1' (D-941) to compare yield parameters using photoperiod extension under differing lamp types. This experiment confirmed the photoperiod responses of D-889 and S-2246 to a mixed-harvest scenario and indicated that daylength extension with higher irradiance from high pressure sodium lamps further suppressed EYR, SHI, and YER of the short-day breeding line D-288.

Non-NASA Center↗
NASA NTRS2006

Demonstrating the Viability and Affordability of Nuclear Surface Power Systems

A set of tasks have been identified to help demonstrate the viability, performance, and affordability of surface fission systems. Completion of these tasks will move surface fission systems closer to reality by demonstrating affordability and performance potential. Tasks include fabrication and test of a 19-pin section of a Surface Power Unit Demonstrator (SPUD); design, fabrication, and utilization of thermal simulators optimized for surface fission' applications; design, fabrication, and utilization of GPHS module thermal simulators; design, fabrication, and test of a fission surface power system shield; and work related to potential fission surface power fuel/clad systems. Work on the SPUD will feed directly into joint NASA MSFC/NASA GRC fabrication and test of a surface power plant Engineering Development Unit (EDU). The goal of the EDU will be to perform highly realistic thermal, structural, and electrical testing on an integrated fission surface power system. Fission thermal simulator work will help enable high fidelity non-nuclear testing of pumped NaK surface fission power systems. Radioisotope thermal simulator work will help enable design and development of higher power radioisotope systems (power ultimately limited by Pu-238 availability). Shield work is designed to assess the potential of using a water neutron shield on the surface of the moon. Fuels work is geared toward assessing the current potential of using fuels that have already flown in space.

Vandyke, Melissa K.↗
NASA NTRS1977

Other Industrial Aids

In another industrial spinoff, O. Z. Gedney Co.,Terryville, Conn., found the answer to a problem in a NASA Tech Brief describing research in adhesive bonding for the Space Shuttle. Gedney, which makes electrical fittings for industrial plants, was developing a new "fire stop," a device that prevents the spread of fire through holes where cables and pipes penetrate fire barriers in buildings. The company wanted to bond a metal disc on the fire stop to a layer of "instumescent" material, material that swells under heat and fills the gap caused by melted cable insulation, thus blocking passage of fire and smoke. At the company's request, NASA supplied a technical information package which identified the best adhesive and the proper bonding technique. The fire-stop fitting is now in production.

Source record↗
NASA NTRS2016

Biotube

Biotube was developed for plant gravitropic research investigating the potential for magnetic fields to orient plant roots as they grow in microgravity. Prior to flight, experimental seeds are placed into seed cassettes, that are capable of containing up to 10 seeds, and inserted between two magnets located within one of three Magnetic Field Chamber (MFC). Biotube is stored within an International Space Station (ISS) stowage locker and provides three levels of containment for chemical fixatives. Features include monitoring of temperature, fixative/ preservative delivery to specimens, and real-time video imaging downlink. Biotube's primary subsystems are: (1) The Water Delivery System that automatically activates and controls the delivery of water (to initiate seed germination). (2) The Fixative Storage and Delivery System that stores and delivers chemical fixative or RNA later to each seed cassette. (3) The Digital Imaging System consisting of 4 charge-coupled device (CCD) cameras, a video multiplexer, a lighting multiplexer, and 16 infrared light-emitting diodes (LEDs) that provide illumination while the photos are being captured. (4) The Command and Data Management System that provides overall control of the integrated subsystems, graphical user interface, system status and error message display, image display, and other functions.

Biotube↗
NASA NTRSDate not supplied

Characterization of Volatiles from Simulated Lunar Highland Melts Under Vacuum

As part of the Artemis program that returns humans to the Moon for sustained presence, the in-situ resource utilization (ISRU) pilot plant is developing hardware to test systems in relevant lunar environments. As this evolves, the ever-growing field of interest requires in-depth understanding of the environment for operations. Lunar regolith contains compounds that can be harvested as resources such as fuel, or life support and construction feedstocks. Therefore, this necessitates an understanding of its constituents and processed by-products under some of the extreme conditions imposed for resource extraction.

Oxygen Extraction↗
NASA NTRSDate not supplied

Characterization of Volatiles from Simulated Lunar Highland Melts Under Vacuum

As part of the Artemis program that returns humans to the Moon for sustained presence, the in-situ resource utilization (ISRU) pilot plant is developing hardware to test systems in relevant lunar environments. As this evolves, the ever-growing field of interest requires in-depth understanding of the environment for operations. Lunar regolith contains compounds that can be harvested as resources such as fuel, or life support and construction feedstocks. Therefore, this necessitates an understanding of its constituents and processed by-products under some of the extreme conditions imposed for resource extraction.

Oxygen Extraction↗
DOE OSTI2021

Risk-informed Predictive Analytics To Achieve Cost-effective Condition-based Monitoring And Maintenance Strategy

The research involves developing risk-informed predictive analytic capabilities to achieve condition-based monitoring and maintenance strategies to reduce overall maintenance costs. The research utilizes data (real-time data, periodic data, and institutional knowledge) related to a particular plant asset from a specific nuclear plant site to develop risk-informed predictive analytic algorithms. The developed algorithms and codes are used to optimize the maintenance strategy and estimate/forecast generation costs based on the state of health of the plant asset. Developed codes specifically include 1. Parameter estimation code based on Bayesian inference 2. Statistical data analysis code 3. Feature engineering code 4. Health classifier code 5. Diagnosis code 6. Prognosis code 7. Hazard code 8. Generation risk code 9. Economic code

Agarwal, Vivek↗