SEARCH · Search NASA

Results for “Processing temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

All sources NASA NTRS DOE OSTI

NASA NTRS2013

Thermal Testing of a Stacked Core Mirror for UV Applications

The ASTRO2010 Decadal Survey stated that an advanced large-aperture ultraviolet, optical, near-infrared (UVOIR) telescope is required to enable the next generation of compelling astrophysics and exoplanet science; and, that present technology is not mature enough to affordably build and launch any potential UVOIR mission concept. Under Science and Technology funding, NASA's Marshall Space Flight Center and ITT Exelis have developed a more cost effective process to make 4m monolithic spaceflight UV quality, low areal density, thermally and dynamically stable primary mirrors. A proof of concept mirror was built and tested down to 250K which would allow imaging out to 2.5 microns. This mirror was thermally tested at the Marshall Spaceflight Center to understand the thermal changes between the processing temperature of 293K and the potential low end of the operational temperature of 250K. Isothermal testing results and front plate gradient results have been evaluated and compared to analysis predictions. Measurement of gravity effects on surface figure will be compared to analytical predictions. Future testing of a larger Pathfinder mirror will also be discussed.

Matthews, Gary↗

NASA NTRS2013

Thermal Testing of a Stacked Core Mirror for UV Applications

Matthews, Gary W.↗

NASA NTRS2018

Nanomanufacturing of Graphene Nanosheets Through Hole Engineering

Facile and scalable fabrication of highly dense and high quality graphene films and articles is extremely attractive for a range of electronic and mechanical applications. Pristine, high quality graphene with its inherent impermeability poses challenges in fabricating dense films and thick parts with high electrical conductivity due to the difficulty in removing trapped air and/or solvents used in various fabrication methods. To overcome this deficiency, nano-holes were intentionally created in pristine graphene (“holey graphene”) with an average diameter of approximately 15 nm. The holes serve as pathways for the rapid removal of gases or liquids and enable the fabrication of dense holey graphene nanostructures. Subsequently, a high temperature process is applied to effectively repair the nano-holes and recover the high quality graphene conjugated network. Through the creation and repair of the nano-holes, dense graphene articles were created that exhibited an ultrahigh conductivity of 2209 S/cm and a high carrier mobility of 673 cm2V-1s-1. This unique processing methodology enables the facile and scalable fabrication of high quality graphene constructs for a variety of applications.

Yanan Chen↗

NASA NTRSDate not supplied

Mapping the Capabilities and Attributes of Solid Oxide Electrochemical Systems to Human Spaceflight Needs

NASA is sponsoring the development of a solid oxide electrochemical oxygen separation and compression system. This system is capable of extracting oxygen from a process stream of spacecraft cabin air, and compressing it to >27,000 kPa without mechanical compressors. Process temperatures are >650C, but the materials in contact with the oxygen do not burn. The system is called eCOG-C, Electrochemical Oxygen Generator and Compressor. A system capable of producing high pressure, high purity oxygen may have application as a method of recharging space suit oxygen tanks during human exploration missions. This paper describes the key performance parameters of a space suit oxygen tank recharge system, and places the key performance parameters of eCOG-c in the context of other methods of space suit oxygen tank recharge. This paper compares the eCOG-c configuration to an earlier electrochemical oxygen generator that has been prototyped and tested. Areas of emphasis for eCOG-C development are listed and described.

John Graf↗

NASA NTRS2022

The Abundances of F, Cl, and H2O in 4Vesta from Eucrites

The abundance and distribution of magmatic volatiles (i.e., H, C, N, F, S, and Cl) within the silicate portion of a differentiated planetary body has important consequences on its thermochemical evolution. However, the abundances of magmatic volatiles within differentiated bodies are difficult to quantify, and they are often depleted by varying degrees relative to CI chondrites. The mechanisms of depletion are not well constrained and could relate to intrinsic volatile depletion of the building blocks that formed the bodies, high temperature processes that result from accretion, post-accretion loss through parent body geological processes and large-scale impacts, and/or redistribution within a parent body through processes like core formation [1–4]. In the present study, we aim to constrain the abundances of F, Cl, and H2O in eucrites to better understand the magnitude of volatile depletion on 4Vesta. To accomplish this objective, we report electron microprobe analyses of apatite from seven unbrecciated, non-cumulate eucrites (i.e., CMS 04049,GRA 98098, LEW 88010, MAC 02522, MAC 041169,QUE 94484, and QUE 97053) and two monomict, non-cumulate eucrites (i.e., Berthoud and Stannern). In combination with previously published data on eucrite-hosted apatite, we determine Cl/F and H2O/F ratios in bulk rock eucrites through the application of apatite-based melt hygrometry and chlorometry [e.g., 5–7].Additionally, we estimate the bulk rock abundances of F in six non-cumulate eucrites (i.e., GRA 98098, MAC041169, PCA 91078, QUE 97053, Stannern, and Berthoud), which we combine with previously published bulk rock F data on non-cumulate eucrites[8] to constrain the abundances of F, Cl, and H2O in 4Vesta using appropriately paired volatile/refractory element ratios for F, followed by Cl/F and H2O/F ratios for Cl and H2O, respectively.

F M McCubbin↗

DOE OSTI2020

Chapter 21. Atomic-Level Dislocation Dynamics in Irradiated Metals

Primary damage and microstructure evolution in structural nuclear materials operating under conditions of a high flux of energetic atomic particles and high temperature and stress lead to the formation of a high concentration, non-homogeneous distribution of defect clusters in the form of dislocation loops, voids, gas-filled bubbles and radiation-induced precipitates of nanometer scale. They cause changes in many material properties. Being obstacles to dislocation glide, they strongly affect the mechanical properties, with an increase in yield and flow stresses and a reduction in ductility. Atomic-scale computer simulations can provide details of how these effects are influenced by the obstacle structure, applied stress, strain rate and temperature. Processes such as obstacle cutting, transformation, absorption and drag are observed. Some recent results for body-centered and face-centered cubic metals are described in this review and, where appropriate, comparisons are drawn with predictions based on the elasticity theory of crystal defects. Perspectives on how to use this information at higher scales and in particular in mesoscale, dislocation dynamics simulations are also discussed.

Osetskiy, Yury N.↗

DOE OSTI2021

Salt ceramic composites and manufacture thereof

Highly dense lithium based ceramics can be prepared by a low temperature process including combining a lithium based ceramic with a polar solvent having a lithium based salt dissolved therein and applying pressure and heat to the combination to form a salt-ceramic composite. Advantageously, the lithium salt is one that dissolves in the polar solvent and the heat applied to the combination is no greater than about 250° C. Such composites can also have high ionic conductivity.

Gomez, Enrique Daniel↗

DOE OSTI2022

Optical systems fabricated by printing-based assembly

Provided are optical devices and systems fabricated, at least in part, via printing-based assembly and integration of device components. In specific embodiments the present invention provides light emitting systems, light collecting systems, light sensing systems and photovoltaic systems comprising printable semiconductor elements, including large area, high performance macroelectronic devices. Optical systems of the present invention comprise semiconductor elements assembled, organized and/or integrated with other device components via printing techniques that exhibit performance characteristics and functionality comparable to single crystalline semiconductor based devices fabricated using conventional high temperature processing methods. Optical systems of the present invention have device geometries and configurations, such as form factors, component densities, and component positions, accessed by printing that provide a range of useful device functionalities. Optical systems of the present invention include devices and device arrays exhibiting a range of useful physical and mechanical properties including flexibility, shapeability, conformability and stretchablity.

Rogers, John↗

DOE OSTI2024

Screen-Printed Complex Ag Inks for Si HJT Metallization

Metallization using reactive metal inks has recently attracted significant research interest due to its advantages in cost of materials and manufacturing, while still achieving performance comparable to traditional fire-through particle pastes. Here, we present for the first time the use of reactive silver (Ag) inks via industrial screen-printing and inkjet printing methods for the metallization of different Si surfaces used in tunneling oxide passivating contacts (TOPCon) and Silicon heterojunction (SHJ) solar cells. Printed Ag lines exhibit a conductivity of ~5 Mu O·cm, which is approximately 3 times that of bulk Ag (1.59 µO·cm). The printed metal has a thickness of ~0.5-1.5 Mu m, an order of magnitude smaller than the current fire-through metal finger thickness (~15 Mu m). Contact resistivity measurements of the screen-printed and inkjet-printed samples on a transparent conducting oxide (TCO) surface show a very low value of ~0.2-12 mO·cm 2. Photoluminescence images of the metallized samples demonstrate minimal surface passivation degradation compared to the non-metallized areas (?iVoc <3.5 mV). Scanning electron microscopy images (SEM) reveal the structure of the printed metals on the Si surfaces as porous but much denser than fire-through Ag by nanoparticle paste. In the final presentation, we will showcase our results of printing these reactive Ag inks on high-efficiency heterojunction and TOPCon solar cells with full-area M6 wafers. Additionally, the adhesion of these reactive Ag inks on different Si surfaces according to ASTM D3359-17, as well as the performance of solar cells after standard IEC 61215 freeze/thaw and damp heat tests, will be presented. These new metal inks show promising potential as an alternative to the currently dominant particle-based pastes, offering lower Ag consumption and lower processing temperatures without compromising performance.

heterojunction solar cells↗

DOE OSTI2025

Undercooling minimization in ultrasound coupled DTA measurements of molten salts

Molten salts are ionic liquids that are used for the electrolytic pyroprocessing of metals and as heat transfer fluids in very high temperature processes. Recently, halide-based molten salt reactors (MSR) have gained momentum for high density and environmentally responsible electricity generation. The function of these reactors and their fuel cycle depend on a knowledge of the halide salt’s thermodynamic properties [1]. Therefore, high accuracy phase equilibria of MSR relevant base halide and actinide containing salts are needed. Modern thermal analysis of the phase transitions of halide salts is usually done during heating at relatively high scan rates with commercial devices. Normally such measurements are adequate for pure or pseudo-binary salts. However, as the number of components in the mixture increases, accurately resolving the liquidus becomes increasingly difficult. Reversing the scanning mode greatly increases the sensitivity of phase transition measurements but can decrease accuracy due to undercooling [2] — a common occurrence in molten halide systems [3]. This work presents the development of a differential thermal analysis (DTA) cell intended for use in radiological gloveboxes. Non-contact ultrasonic agitation of the halide salt is implemented to limit kinetic limitations on crystallization during cooling to minimize undercooling [4]. Measurements on halide salts are also presented to elucidate the effect of non-contact mixing on undercooling. Reference [1] S. Boyd and C. Taylor, “3 - Chemical fundamentals and applications of molten salts,” in Molten Salt Reactors and Thorium Energy, T. J. Dolan, Ed., Woodhead Publishing, 2017, pp. 29–91. doi: 10.1016/B978-0-08-101126-3.00003-8. [2] K. Nitsch, A. Cihlár, and M. Rodová, “Molten state and supercooling of lead halides,” J. Cryst. Growth, vol. 264, no. 1, pp. 492–498, Mar. 2004, doi: 10.1016/j.jcrysgro.2004.01.011. [3] L. Rycerz, “Practical remarks concerning phase diagrams determination on the basis of differential scanning calorimetry measurements,” J. Therm. Anal. Calorim., vol. 113, no. 1, pp. 231–238, Jul. 2013, doi: 10.1007/s10973-013-3097-0. [4] Md. H. Zahir, S. A. Mohamed, R. Saidur, and F. A. Al-Sulaiman, “Supercooling of phase-change materials and the techniques used to mitigate the phenomenon,” Appl. Energy, vol. 240, pp. 793–817, Apr. 2019, doi: 10.1016/j.apenergy.2019.02.045.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

Transition Metal Dichalcogenide MoS 2 : Oxygen and Fluorine Functionalization for Selective Plasma Processing

Low-temperature plasma processing is a promising technique for tailoring transition metal dichalcogenides (TMDs). For chalcogen substitution processing, a key challenge is to identify the ion energy window that enables selective chalcogen removal while preserving the metal lattice. Using ab initio molecular dynamics (AIMD), we demonstrate that oxygen and fluorine functionalization widen the processing window by significantly lowering the sulfur sputtering energy threshold (E sputt,S ) of MoS 2 from ∼30 to ∼10 eV via formation of sputtering products such as SO 2 and SF n . Additionally, we show that experimentally relevant cryogenic temperatures strongly affect E sputt,S (T). The dependence is confirmed via AIMD and also predicted by a mechanistic parameter-free theory, suggesting that E sputt (T) generalizes to other TMDs, functionalizations, and surface impact conditions. Our results highlight oxygen/fluorine functionalization, ionic impact angle, and material temperature to be key control parameters for selective, damage-controlled chalcogen removal in TMD processing.

Polyachenko, Yury [Princeton Plasma Physics Labora↗

NASA NTRS1990

Solid state processing for high temperature alloys and composites

A variety of solid state powder processing methods have been examined for their potential to produce high temperature materials. These techniques included solid state diffusion, mechanical alloying, reaction milling, and exothermic reactions. While both mechanical alloying and exothermic reactions are capable of producing high temperature composites in addition to yielding solid solution and precipitation hardened alloys, reaction milling can only be used to make composite materials. Although at present this method has only been applied to make carbide strengthened Al, recent work indicates that reaction milling is capable of yielding high strength NiAl-AlN composites.

Whittenberger, J. Daniel↗

DOE OSTI2022

Thermal Process Intensification: Transforming the Way Industry Uses Thermal Process Energy (Workshop Report)

The US Department of Energy’s (DOE’s) Advanced Manufacturing Office held the virtual workshop entitled “Thermal Process Intensification: Transforming the Way Industry Uses Thermal Process Energy” in November and December 2020. The workshop brought together participants from universities/laboratories, industries, equipment manufacturers, technology vendors, nongovernmental organizations, and subject-matter experts to discuss transformative technologies and strategies to substantially improve the performance (e.g., energy productivity, thermal efficiency, reduced greenhouse gas [GHG] emissions, reduced number of process steps) of thermal processing systems in the industrial sector. The US industrial sector accounts for 32% of the nation’s primary energy use (including feedstocks), and refining, chemicals, pulp and paper, iron and steel, and food products represent the top energy-consuming sectors. Thermal processing or process heating represents the largest energy use category; it accounts for 63% of all energy use in manufacturing. Additionally, thermal processing is the largest contributor of carbon dioxide (CO2) generation, resulting from combustion of fuels and process related chemical reactions, such as in the case of cement and lime production. The challenge of achieving net-zero industrial GHG emissions is colossal considering the established industrial base that depends mainly on carbon-based processes and energy sources; the time frame and cost to replace carbon-based energy sources and feedstocks; and the long-term outlook for development with large-scale adaptation of alternative non carbon–based technologies. The goals of the DOE Advanced Manufacturing Office Thermal Process Intensification Workshop were as follows: (1) Identify R&D gaps and opportunities to facilitate transformative improvement in industrial thermal processes beyond current technologies and allow for entirely new methods for processing materials; (2) Gain insight into new and innovative approaches to thermally intensify processes, reduce heat demand, harness waste heat, and use fuels and hydrocarbon feedstocks more efficiently; (3) Identify the R&D pathways to thermal process intensification (TPI) with the highest potential for impact and adoption by the industrial sector; (4) Define areas of research, development, and demonstration (RD&D) activities to accelerate development and application of emerging and transformative technologies to intensify thermal processes in industry. The scope and focus of the workshop were defined to meet these goals. Based on the available data for energy use and GHG emissions, the industries that collectively use more than 80% of the total process heating energy consumption were selected as primary focus areas. The chosen industries were combined into the following four groups based on similarities in their thermal processes: high-temperature metal processing (iron and steel industry, alumina-aluminum industry); high-temperature nonmetal and mineral processing (cement and glass industry); medium- to low-temperature thermal processing (food processing and pulp and paper industry as part of forest products sector); and hydrocarbon processing (petroleum refining and chemical industry). Furthermore, all potential TPI technologies associated with the processes defined were considered as part of the workshop. Different types of TPI technologies possible in industrial in the document.

42 ENGINEERING↗

NASA NTRS1989

Low temperature multi-alkali photocathode processing technique for sealed intensified CCD tubes

A low temperature photocathode process has been used to fabricate an intensified CCD visual photocathode image tube, by incorporating a thinned, backside-illumined CCD as the target anode of a digicon tube of Hubble Space Telescope (HST) design. The CCD digicon tube employs the HST's sodium bialkali photocathode and MgF2 substrate, thereby allowing a direct photocathode quantum efficiency comparison between photocathodes produced by the presently employed low temperature process and those of the conventional high temperature process. Attention is given to the processing chamber used, as well as the details of gas desorption and photocathode processing.

Doliber, D. L.↗

NASA NTRS1991

Containerless processing at high temperatures using acoustic levitation

Advanced techniques are presented which facilitate the development of inert or reducing atmospheres in excess of 2000 K in order to improve processing of containerless capabilities at higher temperatures and to provide more contamination-free environments. Recent testing, in the laboratory and aboard the NASA KC-135 aircraft, of a high-temperature acoustic positioner demonstrated the effectiveness of a specimen motion damping system and of specimen spin control. It is found that stable positioning can be achieved under ambient and heated conditions, including the transient states of heat-up and cool-down. An incorporated high-temperature levitator was found capable of processing specimens of up to 6-mm diameter in a high-purity environment without the contaminating effects of a container at high temperatures and with relative quiescence.

Rey, C. A.↗

DOE OSTI2020

Heat-induced drift reduction of time of flight in fused quartz acoustic waveguides via annealing process

High temperature structural acoustic sensors play an important role in many applications. Fused quartz waveguide is a popular choice due to its resistance to harsh environments and its convenience of modification. However, time of flight between pulse and echo, which is widely used in these sensors, tends to encounter drifts in fast temperature changing process even after temperature returns to initial value. In this article, different annealing process are performed for a special modified fused quartz waveguide with a sensor node. Annealing treatment is found able to reduce the drift when the waveguide undergoes a sudden temperature spike to 1000 °C at 500 kHz operating acoustic frequency, and the best annealing condition could make the drift one magnitude smaller. A following temperature test up to 1000 °C shows consistent measurement readings.

Hileman, Zachary (ORCID:0000000226529274)↗

NASA NTRS2013

Advanced Signal Processing for High Temperatures Health Monitoring of Condensed Water Height in Steam Pipes

An advanced signal processing methodology is being developed to monitor the height of condensed water thru the wall of a steel pipe while operating at temperatures as high as 250deg. Using existing techniques, previous study indicated that, when the water height is low or there is disturbance in the environment, the predicted water height may not be accurate. In recent years, the use of the autocorrelation and envelope techniques in the signal processing has been demonstrated to be a very useful tool for practical applications. In this paper, various signal processing techniques including the auto correlation, Hilbert transform, and the Shannon Energy Envelope methods were studied and implemented to determine the water height in the steam pipe. The results have shown that the developed method provides a good capability for monitoring the height in the regular conditions. An alternative solution for shallow water or no water conditions based on a developed hybrid method based on Hilbert transform (HT) with a high pass filter and using the optimized windowing technique is suggested. Further development of the reported methods would provide a powerful tool for the identification of the disturbances of water height inside the pipe.

health monitoring↗

DOE OSTI2020

Sound Speed as a Candidate for Internal Temperature Monitoring During Solid Phase Processing of Materials

Internal temperature is an important parameter for understanding the solid phase processing (SPP) of materials and improving feedback control of these processes. Friction stir processes, shear assisted processing and extrusion (ShAPE ™ ), and ultrahigh velocity (UHV) cold spray are examples of such processes. Simple thermal models based on temperatures measured at the boundary of the deforming body cannot capture the dynamic nature of temperature generation within the deforming solid. One possibly way of understanding internal temperature is by measuring sound speed, which varies as a function of temperature for materials and directing ultrasonic wave propagation through selected material volumes of interest. In this project, longitudinal wave speed is estimated for aluminum 6061. Piezoelectric materials bonded to a specimen provided data from which longitudinal wave speed was estimated. A discussion evaluated the linear relationship of wave speed versus temperature and postulated how wave speed measurements could be used to estimate the internal temperature of selected material volumes for feedback during SPP of materials. Instrumentation, data and analysis, and a discussion are reviewed.

36 MATERIALS SCIENCE↗