Search NASA⌕ Search

SEARCH · Search NASA

Results for “RECTANGULAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

CFD mixing analysis of jets injected from straight and slanted slots into confined crossflow in rectangular ducts

A CFD study was performed to analyze the mixing potential of opposed rows of staggered jets injected into confined crossflow in a rectangular duct. Three jet configurations were numerically tested: (1) straight (0 deg) slots; (2) perpendicular slanted (45 deg) slots angled in opposite directions on top and bottom walls; and (3) parallel slanted (45 deg) slots angled in the same direction on top and bottom walls. All three configurations were tested at slot spacing-to-duct height rations (S/H) of 0.5, 0.75, and 1.0; a jet-to-mainstream momentum flux ratio (J) of 100; and a jet-to-mainstream mass flow ratio of 0.383. Each configuration had its best mixing performance at S/H of 0.75. Asymmetric flow patterns were expected and predicted for all slanted slot configurations. The parallel slanted slot configuration was the best overall configuration at x/H of 1.0 for S/H of 0.75.

Bain, D. B.↗
NASA NTRS1992

Experimental study of cross-stream mixing in a rectangular duct

An experimental investigation of non-reacting cross-stream jet injection and mixing in a rectangular duct was conducted for application in a low emissions combustor. Planar digital imaging was used to measure concentration distributions in planes perpendicular to the duct axis. Mixing rate was measured for 45 deg slanted slot and round orifice injectors. Five areas of inquiry are discussed: (1) mixing improves continuously with increasing momentum-flux ratio; (2) given a momentum-flux ratio, there is an optimum, orifice spacing; (3) mixing is more dependent on injector geometry than mass flow ratio; (4) mixing is influenced by relative slot orientation; and (5) jet structure is different for round holes and slanted slots injectors. The utility of acquiring multipoint fluctuating properties of the flow field is also demonstrated.

Liscinsky, D. S.↗
NASA NTRS1992

Mutual coupling between rectangular microstrip patch antennas

The paper presents a comprehensive study of the mutual coupling between two rectangular microstrip patch antennas. The cavity model is employed to give numerical results for both mutual impedance and mutual coupling parameters for the E-plane, H-plane, diagonal, and perpendicular orientations. The effects of substrate thickness, substrate permittivity, and feed positions are discussed.

Huynh, Tan↗
NASA NTRS1992

Effect of a simulated glaze ice shape on the aerodynamic performance of a rectangular wing

The effect of a simulated glaze-ice accretion on the flowfield of a 3D wing is studied experimentally. The model used for these tests was a semispan wing of effective aspect ratio five, mounted from the sidewall of a subsonic wind tunnel. The model has a NACA 0012 airfoil section on a rectangular untwisted planform with interchangeable leading edges to allow for testing both the baseline and the iced-wing geometry. A four-beam two-color fiberoptic laser Doppler velocimeter (LDV) was used to map the flowfield along three spanwise cuts on the model. Measurements on the centerline of the clean model compared favorably with theory and centerline measurements on the iced model compared well with measurements on a similar 2D model. The flow has the largest separation bubble at the model midspan with the smallest separation bubble occurring near the root and the wing tip.

Khodadoust, Abdi↗
NASA NTRS1993

Rectangular Array Of Digital Processors For Planning Paths

Prototype 24 x 25 rectangular array of asynchronous parallel digital processors rapidly finds best path across two-dimensional field, which could be patch of terrain traversed by robotic or military vehicle. Implemented as single-chip very-large-scale integrated circuit. Excepting processors on edges, each processor communicates with four nearest neighbors along paths representing travel to north, south, east, and west. Each processor contains delay generator in form of 8-bit ripple counter, preset to 1 of 256 possible values. Operation begins with choice of processor representing starting point. Transmits signals to nearest neighbor processors, which retransmits to other neighboring processors, and process repeats until signals propagated across entire field.

Kemeny, Sabrina E.↗
NASA NTRS1992

Study of narrow-band dichroic plates with circular, rectangular, or Pyleguide apertures

The dichroic plate considered in this article is a metal plate perforated with arrays of apertures such that electromagnetic waves of certain frequencies pass through the plate and other frequencies are reflected. The shape of the apertures is an important contributor to the performance of the dichroic plate. An S/X dichroic plate, which passes X-band (8.4-8.45 GHz) and reflects S-band (2.0-2.32 GHz), is chosen for a case study. A comparison of the performance of dichroic plates of the same thickness and array pattern is presented for three different aperture shapes: circular, Pyleguide, and rectangular.

Chen, J. C.↗
NASA NTRS1993

Feasibility study of a Ka-/Ka-band dichroic plate with stepped rectangular apertures

For the Cassini spacecraft mission, a dichroic plate is needed to pass Ka-band uplink (34.2 to 34.7 GHz) and to reflect Ka-band downlink (31.8 to 32.3 GHz) for dual-frequency operation in the Deep Space Network. The special characteristic of the Ka-/Ka-band dichroic plate is that the pass band and the reflective band are only 1.9 GHz (5.7 percent) apart. A thick dichroic plate with stepped rectangular apertures that function as resonator filters was chosen for the Ka-/Ka-band dichroic plate design. The results of the feasibility study are presented in this article.

Chen, J. C.↗
NASA NTRS1993

Experimental investigation of crossflow jet mixing in a rectangular duct

An experimental investigation of the mixing of nonreacting opposed rows of jets injected normal to a confined rectangular crossflow has been conducted. Planar Mie-scattering was used to measure the time-average concentration distribution of the jet fluid in planes perpendicular to the duct axis. The mixing effectiveness of round orifice injectors was measured as a function of orifice spacing and orifice diameter. Mixing effectiveness was determined using a spatial unmixedness parameter based on the variance of mean jet concentration distributions. Optimum mixing was obtained when the spacing-to-duct height ratio was inversely proportional to the square root of the jet-to-mainstream momentum-flux ratio. For opposed rows of round holes with centerlines inline, mixing was similar for blockages up to 75 percent. Lower levels of unmixedness were obtained as a function of downstream location when axial injection length was minimized. Mixing may be enhanced if orifice centerlines of opposed rows are staggered, but note that blockage must be less than 50 percent for this configuration.

Liscinsky, D. S.↗
NASA NTRS1993

Experimental study of cross flow mixing in cylindrical and rectangular ducts

An experimental investigation of non-reacting cross flow jet injection and mixing in cylindrical and rectangular ducts has been conducted with application to a low emissions combustor. Quantitative measurement of injectant concentration distributions perpendicular to the duct axis were obtained by planar digital imaging of the Mie-scattered light from an aerosol seed mixed with the injectant. The flowfield unmixedness was evaluated using (1) a mixing parameter derived from the ratio of the jet concentration fluctuations to the fully mixed concentration, and (2) probability density functions of the concentration distributions. Mixing rate was measured for 45 degree slant slot and round orifice injectors.

Liscinsky, D. S.↗
NASA NTRS1992

Experimental verification of the asymtotic modal analysis method as applied to a rectangular acoustic cavity excited by structural vibration

An experiment was performed on a rigid wall rectangular acoustic cavity driven by a flexible plate mounted in a quarter of one end wall and excited by white noise. The experiment was designed so that the assumptions of Asymptotic Modal Analysis (AMA) were satisfied for certain bandwidths and center frequencies. Measurements of sound pressure levels at points along the boundaries and incrementally into tbe interior were taken. These were compared with the theoretical results predicted with AMA, and found to be in good agreement, particularly for moderate (1/3 octave) bandwidths and sufficiently high center frequencies. Sound pressure level measurements were also taken well into the cavity interior at various points along the 5 totally rigid walls. The AMA theory, including boundary intensification effects, was shown to be accurate provided the assumption of large number of acoustic modes is satisfied, and variables such as power spectra of the wall acceleration, frequency, and damping are slowly varying in the frequency of bandwidth.

Peretti, L. F.↗
NASA NTRS1992

Instability of rectangular jets

The instability of rectangular jets is investigated using a vortex sheet model. It is shown that such jets support four linearly independent families of instability waves. Within each family there are infinitely many modes. A way to classify these modes according to the characteristics of their mode shapes or eigenfunctions is proposed. A parametric study of the instability wave characteristics has been carried out. A sample of the numerical results is reported here. It is found that the first and third modes of each instability wave family are corner modes. The pressure fluctuations associated with these instability waves are localized near the corners of the jet. The second mode, however, is a center mode with maximum fluctuations concentrated in the central portion of the jet flow. The center mode has the largest spatial growth rate. It is anticipated that as the instability waves propagate downstream the center mode would emerge as the dominant instability of the jet.

Tam, Christopher K. W.↗
NASA NTRS1993

On the generation of secondary motion in circular to rectangular transition ducts

A computer code has been developed for the calculation of three-dimensional turbulent flow in circular to rectangular transition ducts. The governing equations are written in a general curvilinear coordinate system so that all singly-connected geometrical configurations can be accommodated. Turbulence closure is through the standard k-epsilon model or a Reynolds stress closure model. Computed results show qualitative agreement with experimental data. Pressure-induced secondary flow is the dominant mode through the transition, but turbulence-induced secondary flow becomes prominent some distance downstream of the transition.

Demuren, A. O.↗
NASA NTRS1993

Compression buckling response of tailored rectangular composite plates

Buckling resistance is often a controlling criterion in the design of structures composed of plate elements. Design concepts that lead to increased buckling loads (or strains) of these plate elements can directly lower the structural cost and/or weight by a number of means. This study quantifies the improvements that can be achieved in compression buckling loads of rectangular composite plates by using a simple stiffness-tailoring concept. The approach is to position the unidirectional lamina through the thickness and over the planform of the plate so that the buckling load is increased with no loss in in-plane stiffness or increase in weight. Finite element analyses have been used to determine the effects of tailoring on the buckling loads of plates with various boundary conditions, aspect ratios, thicknesses, and membrane stiffnesses. Increases in buckling loads (or strains) of 200 percent or more compared to the uniform plate-buckling loads are shown possible with this tailoring concept.

Biggers, Sherrill B.↗
NASA NTRS1993

Relations for local radiative heat transfer between rectangular boundaries of an absorbing-emitting medium

An analytical solution was obtained by Siegel (1991, 1992) for local boundary heat fluxes by a radiating medium at uniform temperature in a 2D rectangular region. It is shown here that, after local fluxes from the medium to the walls have been evaluated, it is very easy to compute local fluxes arriving from the adjacent and opposite walls. This extends the previous analysis and provides convenient relations to include radiation from a black boundary, each side of the rectangle being at a different uniform temperature. The final expressions are helpful in performing spectral calculations that must be made for many spectral bands.

Siegel, R.↗
NASA NTRS1991

Improved compression buckling for rectangular composite plates by stiffness tailoring

Buckling resistance is often a controlling criterion in the design of structural elements. Design concepts that lead to increased buckling loads (or strains) can directly lower the structural cost and/or weight by a number of means. This study quantifies the improvements that can be achieved in compression buckling loads of rectangular composite plates by using a simple stiffness tailoring concept. The approach is to position the unidirectional lamina through the thickness and over the planform of the plate so that the buckling load is increased with no loss in in-plane stiffness or increase in weight. Finite element analyses have been used to determine the effects of tailoring on the buckling load of plates with various boundary conditions, aspect ratios, thicknesses, and membrane stiffnesses. Increases in buckling loads (or strains) of nearly 200 percent over the uniform plate buckling loads are shown possible with this tailoring concept.

Biggers, Sherrill B.↗
NASA NTRS1993

Shear buckling response of tailored, rectangular, composite plates

The concept of stiffness tailoring for improved shear buckling resistance of rectangular composite plates is investigated analytically. The tailoring involves only the redistribution of the given material with given orientations to create beneficial stiffening patterns across the planform of the plate. The resulting local nonuniformities in thickness and membrane and bending stiffness combine to change the buckling response of the plate. The weight and average membrane shear stiffness are essentially unaffected by the tailoring. Practical limitations on the degree to which the tailoring may be carried out are shown to govern most designs. Improvements in the shear buckling load on the order of 50 percent are shown possible with monolithic tailoring. Tailored sandwich concepts, in which a light-weight core material is added to keep both plate surfaces flat, can produce improvements well over 100 percent in specific buckling loads compared with uniform composite plates.

Biggers, Sherrill B.↗
NASA NTRS1993

Instability of rectangular jets

The instability of rectangular jets is investigated using a vortex-sheet model. It is shown that such jets support four linearly independent families of instability waves. Within each family there are infinitely many modes. A way to classify these modes according to the characteristics of their mode shapes or eigenfunctions is proposed. It is demonstrated that the boundary element method can be used to calculate the dispersion relations and eigenfunctions of these instability wave modes. The method is robust and efficient. A parametric study of the instability wave characteristics has been carried out. A sample of the numerical results is reported here. It is found that the first and third modes of each instability wave family are corner modes. The pressure fluctuations associated with these instability waves are localized near the corners of the jet. The second mode, however, is a center mode with maximum fluctuations concentrated in the central portion of the jet flow. The center mode has the largest spatial growth rate. It is anticipated that as the instability waves propagate downstream the center mode would emerge as the dominant instability of the jet.

Tam, Christopher K. W.↗
NASA NTRS1993

Input impedance of coaxially fed rectangular microstrip antenna on electrically thick substrate

A full-wave spectral domain analysis has been used to obtain input-impedance results for a probe-fed rectangular-patch antenna, modeling the source as a magnetic-current frill. Multiple modes are used in the probe surface current to account for axial and azimuthal variations. It is established that maximum resistance is dependent on the substrate loss tangent. The axial variation of the probe current must be taken into account for substrate thicknesses greater than about 0.02 wavelengths.

Chen, Wei↗