Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reference Standards”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

A Comparison of Two Terminal Area Detect and Avoid Well Clear Definitions

Technical requirements are currently under development for a detect and avoid system (DAA) that would support the operation of Unmanned Aircraft Systems (UAS) within the National Airspace System (NAS). Such a system would aid UAS operators in maintaining sufficient separation, or "well clear", from other aircraft in their vicinity. The first set of technical standards for a UAS DAA system (referred to as "Phase 1" requirements) was limited to UAS operations transiting through Class D, E, and G airspace to, or from, Class A (or special-use) airspace. Explicitly out of scope of the Phase 1 requirements was the operation of UAS within terminal airspace in the NAS. Fern, Rorie, Roberts and Monk (2018) explored the application of a Phase 1 DAA system within Class D terminal airspace in a human-in-the-loop simulation. The results of the study demonstrated a poor fit of the Phase 1 DAA well clear (DWC) definition to these terminal operations. The original DWC definition was designed for the en-route environment and could not account for the complex, tightly-choreographed nature of traffic typically found near an airport. The interaction of the en-route DWC definition and the terminal area traffic led to excessive DAA alerting against safely-separated traffic. The frequent alerting quickly degraded pilots' ability to discriminate between encounters where a maneuver was or was not necessary. This resulted in slower response times, higher rates of losses of DAA well clear, and more severe losses of DAA well clear than had been observed in previous DAA research (e.g., Rorie et al., 2017). The current paper reports on a follow-on study to Fern et al. (2018) that tested two DWC definitions designed to accommodate standard terminal area operating procedures, such as traffic in the downwind leg of a VFR traffic pattern while the UAS is on final. The two definitions utilized identical horizontal and vertical thresholds but differed in whether or not Tau (a function that takes into account the closure rate of two aircraft) was included as a part of the DWC hazard zone. The "Tau" DWC candidate definition nominally extended the DWC hazard zone by 15 seconds in the direction of the intruder aircraft, while the "No Tau" DWC candidate definition did not extend the DWC hazard zone. The results of this follow-on study indicated that both candidate definitions improved pilot and DAA system performance relative to Fern et al (2018). Pilot response times and rates of losses of DWC returned to levels comparable to earlier research in the en-route environment. Several important differences between the two DWC candidate definitions, however, are also discussed.

Terminal Area↗
NASA NTRS1988

Subpixel translation-registration of random fields

The author examines both theoretically and through a simulation study the feasibility of identifying the location within a large reference gray-level array of a smaller sensed array to an accuracy finer than one pixel. It is assumed that the sensed image before discretization into pixels consists of a translated, but not rotated, section of the reference image with some superposed noise. The theoretical and empirical results show that when the noise has standard deviation no larger than that of a realistic reference field, the upper quartile of the registration error is on the order of 0.25-0.5 pixels.

Slud, Eric V.↗
NASA NTRSDate not supplied

Enabling Simulation Interoperability between International Standards in the Space Domain

Today, the design and development of space systems are conducted cooperatively by historical space agencies in this area such as NASA, ESA, Roscosmos, and JAXA together with their industrial partners. The space system lifecycle is characterized by high costs, uncertain conditions, and dangerous scenarios. To mitigate these issues, space agencies rely heavily on Modelling and Simulation as a key technology to support the analysis, design, and operation of space systems. To support large-scale distributed simulations, the scientific community has developed several standards to support the reuse and interoperability of simulation models such as IEEE 1516 High-Level Architecture (HLA), Real-time Platform Reference Federation Object Model (RPR FOM), Simulation Model Portability (SMP), and the novel Space Reference Federation Object Model (SpaceFOM). While the SpaceFOM standard has been specifically conceptualized for handling space systems, the other ones are more general-purpose and can be used to design and simulate generic complex systems. As a consequence, there is a lake of rules and guidelines to enable interoperability among these standards. The paper presents solutions and experiences for enabling interoperability and transferability of HLA, RPR FOM, and SMP simulation models with SpaceFOM.

Simulation↗
NASA NTRS1971

Induction brazing manual

Manual presents standards and techniques which are known or are particular to specific industry, and is useful as guide in closing tolerance brazing. Material and equipment specifications, tool setting tables, and quality control data and instructions are included. Since similar standards are available, manual is supplementary reference.

Source record↗
NASA NTRS1975

Demonstration of optical navigation measurements on Mariner 10

An experiment was performed on the Mariner 10 Venus/Mercury mission to assess the performance of the onboard television cameras and ground-based software used in the optical navigation measurement system. The elements of the system, calibration, and distortion are considered. The navigation technique requires detection of stars in the same field of view as the target body. The star detection capability is discussed with reference to required threshold, calibration factors, standard conditions, camera sensitivity, response uniformity, and the effect of image smearing. Tests conducted during the Mariner 10 encounters with Mercury demonstrated that a large bright planet can be imaged simultaneously with faint stars to provide accurate navigation data. Improvements are suggested in the system for the Mariner Jupiter/Saturn 1977 and later missions.

Stanton, R. H.↗
NASA NTRS1976

LACIE performance predictor final operational capability program description, volume 2

Given the swath table files, the segment set for one country and cloud cover data, the SAGE program determines how many times and under what conditions each segment is accessed by satellites. The program writes a record for each segment on a data file which contains the pertinent acquisition data. The weather data file can also be generated from a NASA supplied tape. The Segment Acquisition Selector Program (SACS) selects data from the segment reference file based upon data input manually and from a crop window file. It writes the extracted data to a data acquisition file and prints two summary reports. The POUT program reads from associated LACIE files and produces printed reports. The major types of reports that can be produced are: (1) Substrate Reference Data Reports, (2) Population Mean, Standard Deviation and Histogram Reports, (3) Histograms of Monte Carlo Statistics Reports, and (4) Frequency of Sample Segment Acquisitions Reports.

Source record↗
NASA NTRS1976

DSN standard interface adapter and buffer assembly used in the Mark 3 data system

The DSN Standard Interface Adapter and Buffer Assembly (referred to as the 900/SIA) is used to effect interface compatibility between the Xerox data systems 920 computer (XDS 920) and the Mark 3 data system (MDS) processors. It sets forth the requirements based on the differences between the two systems. Operational characteristics and general design strategy are described, as well as certain efficient implementation techniques used. From a software standpoint, the transfer protocol is discussed to a level of detail sufficient for its operation.

Anderson, T.↗
NASA NTRS1978

Theoretical simulation of solar spectra in the middle ultraviolet and visible for atmospheric trace constituent measurements

Two balloon flights reaching float altitudes of approximately 30 and 40 km respectively, were used to obtain scans of the ultraviolet and visible solar spectra. Both flights covered the UV (2800-3500A) at approximately 0.3A resolution and the visible at approximately 0.6A. Numerous scans were obtained during ascent and from float for both flights. All spectral scans obtained at float, from high sun to low sun, were calibrated in wavelength by using several standard solar spectra for line position references. Comparisons of low sun scans and high sun scans show significant atmospheric continuum extinction and have the potential of being used to identify atmospheric lines superimposed on the attenuated solar spectrum. The resolution was mathematically degraded to approximately 5A to better see the broad band atmospheric extinction. This low resolution is also appropriate for the available low resolution absorption coefficients of NO2 and O3, allowing the identification of NO2 and O3 features on the sunset spectra.

Goldman, A.↗
NASA NTRS1980

A three-dimensional body-fitted coordinate system for flow field calculations on asymmetric nosetips

A three dimensional body-fitted coordinate system developed for use in the calculation of inviscid flows over ablated, asymmetric reentry vehicle nosetips is described. Because of the potential geometric asymmetries, no standard coordinate system (e.g., spherical, axisymmetric reference surface-normal) is capable of being closely aligned with the nosetip surface. To generate a 3-D, body-fitted coordinate system an analytic mapping procedure is applied that is conformal within each meridional plane of the nosetip; these transformations are then coupled circumferentially to yield a three dimensional coordinate system. The mappings used are defined in terms of hinge points, which are points selected to approximate the body contours in each meridional plane. The selection of appropriate hinge points was automated to facilitate the use of the resulting nosetip flow field code.

Hall, D. W.↗
NASA NTRS1983

Progress In The Scene-To-Map Registration Investigation

The geometric accuracy of the scene-to-map registration process for P-format LANDSAT MSS data for scenes from Kansas and Louisiana/Mississippi is discussed. Large scale row and column bias values and row and column standard deviation values were measured for the P-format data sets indicating a poor georegistration accuracy for these geometrically corrected LANDSAT MSS scenes. Experimental work is underway with A-format LANDSAT MSS scenes from the same locations to examine the influence of the number of ground control points and the spatial distribution of ground control points on geometric registration accuracy. An early conclusion from this work is that the root mean square approach for assessing how well the ground control points fit the mapping equations measures a different aspect of georegistration accuracy than does the approach of evaluating the bias (offset) and standard deviation using independently chosen ground reference points.

Dow, D. D.↗
NASA NTRS1984

Navigation system and method

In a global positioning system (GPS), such as the NAVSTAR/GPS system, wherein the position coordinates of user terminals are obtained by processing multiple signals transmitted by a constellation of orbiting satellites, an acquisition-aiding signal generated by an earth-based control station is relayed to user terminals via a geostationary satellite to simplify user equipment. The aiding signal is FSK modulated on a reference channel slightly offset from the standard GPS channel. The aiding signal identifies satellites in view having best geometry and includes Doppler prediction data as well as GPS satellite coordinates and identification data associated with user terminals within an area being served by the control station and relay satellite. The aiding signal significantly reduces user equipment by simplifying spread spectrum signal demodulation and reducing data processing functions previously carried out at the user terminals.

Taylor, R. E.↗
NASA NTRS1993

Federal Communications Commission (FCC) Transponder Loading Data Conversion Software. User's guide and software maintenance manual, version 1.2

This volume contains the complete software system documentation for the Federal Communications Commission (FCC) Transponder Loading Data Conversion Software (FIX-FCC). This software was written to facilitate the formatting and conversion of FCC Transponder Occupancy (Loading) Data before it is loaded into the NASA Geosynchronous Satellite Orbital Statistics Database System (GSOSTATS). The information that FCC supplies NASA is in report form and must be converted into a form readable by the database management software used in the GSOSTATS application. Both the User's Guide and Software Maintenance Manual are contained in this document. This volume of documentation passed an independent quality assurance review and certification by the Product Assurance and Security Office of the Planning Research Corporation (PRC). The manuals were reviewed for format, content, and readability. The Software Management and Assurance Program (SMAP) life cycle and documentation standards were used in the development of this document. Accordingly, these standards were used in the review. Refer to the System/Software Test/Product Assurance Report for the Geosynchronous Satellite Orbital Statistics Database System (GSOSTATS) for additional information.

Mallasch, Paul G.↗
NASA NTRS1993

Interim report on Landsat national archive activities

The Department of the Interior (DOI) has the responsibility to preserve and to distribute most Landsat Thematic Mapper (TM) and Multispectral Scanner (MSS) data that have been acquired by the five Landsat satellites operational since July 1972. Data that are still covered by exclusive marketing rights, which were granted by the U.S. Government to the commercial Landsat operator, cannot be distributed by the DOI. As the designated national archive for Landsat data, the U.S. Geological Survey's EROS Data Center (EDC) has initiated two new programs to protect and make available any of the 625,000 MSS scenes currently archived and the 200,000 TM scenes to be archived at EDC by 1995. A specially configured system has begun converting Landsat MSS data from obsolete high density tapes (HDT's) to more dense digital cassette tapes. After transcription, continuous satellite swaths are (1) divided into standard scenes defined by a world reference system, (2) geographically located by latitude and longitude, and (3) assessed for overall quality. Digital browse images are created by subsampling the full-resolution swaths. Conversion of the TM HDT's will begin in the fourth quarter of 1992 and will be conducted concurrently with MSS conversion. Although the TM archive is three times larger than the entire MSS archive, conversion of data from both sensor systems and consolidation of the entire Landsat archive at EDC will be completed by the end of 1994. Some MSS HDT's have deteriorated, primarily as a result of hydrolysis of the pigment binder. Based on a small sample of the 11 terabytes of post-1978 MSS data and the 41 terabytes of TM data to be converted, it appears that to date, less than 2 percent of the data have been lost. The data loss occurs within small portions of some scenes; few scenes are lost entirely. Approximately 10,000 pre-1979 MSS HDT's have deteriorated to such an extent, as a result of hydrolysis, that the data cannot be recovered without special treatment of the tapes. An independent consulting division of a major tape manufacturer has analyzed affected tapes and is confident that restorative procedures can be applied to the HDT's to permit one pass to reproduce the data on another recording media. A system to distribute minimally processed Landsat data will be procured in 1992 and will be operational by mid-1994. Any TM or MSS data in the national archive that are not restricted by exclusive marketing rights will be reproduced directly from the archive media onto user specified computer-compatible media. TM data will be produced either at a raw level (radiometrically and geometrically uncorrected) or at an intermediate level (radiometrically corrected and geometrically indexed). MSS data will be produced to an intermediate level or to a fully corrected level (radiometrically corrected and geometrically transformed to an Oblique Mercator projection). The system will be capable of providing ordered scenes within 48 hours of receipt of order.

Boyd, John E.↗
NASA NTRS1993

Current state of the mass storage system reference model

IEEE SSSWG was chartered in May 1990 to abstract the hardware and software components of existing and emerging storage systems and to define the software interfaces between these components. The immediate goal is the decomposition of a storage system into interoperable functional modules which vendors can offer as separate commercial products. The ultimate goal is to develop interoperable standards which define the software interfaces, and in the distributed case, the associated protocols to each of the architectural modules in the model. The topics are presented in viewgraph form and include the following: IEEE SSSWG organization; IEEE SSSWG subcommittees & chairs; IEEE standards activity board; layered view of the reference model; layered access to storage services; IEEE SSSWG emphasis; and features for MSSRM version 5.

Coyne, Robert↗
NASA NTRS1994

Revision of the Dobson total ozone series at Hohenpeissenberg

Total ozone measurements with the Dobson No. 104 (D 104) have been performed at the Meteorological Observatory Hohenpeissenberg since 1967. A critical review of this time series and the comparison with other instruments like TOMS or Brewer spectrophotometer revealed some intervals with uncertainties. Especially in the early eighties a monthly mean bias of about minus 3 percent to TOMS-data with annual variations depending on the mean sun-height exists. An extreme amplitude of 5.6 percent occurs in 1980 with minus 0.76 percent (February) and minus 6.36 percent (July). Two different methods were applied to reprocess the Dobson data set. A comparison of the differently recalculated data showed, that the application of N-corrections by means of the standard-lamp tests starting from the reference values of the Arosa Intercomparison 1986 yields better results than the N-corrections based on a Langley-pilot of the Arosa Intercomparison 1978. The extreme amplitude of the year 1980 is now reduced to 3.02 percent. There is still a slight drift in the monthly and yearly mean differences between TOMS and revised Dobson data. It cannot be excluded, that the satellite data may be responsible for the trend.

Koehler, U.↗
NASA NTRS1996

SeaWiFs Technical Report Series. Volume 34: The Third SeaWiFS Intercalibration Round-Robin Experiment (SIRREX-3), 19-30 September 1994

This report presents results of the third Sea-viewing Wide Field-of-view Sensor (SeaWiFS) Intercalibration Round- Robin Experiment (SIRREX-3), which was held at the San Diego State University (SDSU) Center for Hydro-Optics and Remote Sensing (CHORS) on 19-30 September 1994. Spectral irradiances of FEL lamps belonging to each participant were intercompared by reference to the National Institute of Standards and Technology (NIST) scale of spectral irradiance using secondary standard lamps F268, F269, and F182, with a Type A uncertainty between 1.1-1.5%. This level of uncertainty was achieved despite difficulties with lamp F269. The average spectral irradiances of FEL lamps, compared in both SIRREX-2 and SIRREX-3, differed between the two experiments by 1.5%, which probably indicates that the values assigned to the secondary standard lamp at the time of SIRREX-2 were in error. With two exceptions, spectral radiance values of integrating sphere sources were measured during SIRREX-3 with uncertainties in temporal stability of less than 0.3% and absolute uncertainties of 1.5-2.0%. This is a significant improvement over similar intercomparisons in SIRREX- I and SIRREX-2. Plaque reflectances were intercompared with an uncertainty of about 1-2%, but the absolute uncertainty is undefined. Although this is an improvement over results of previous SIRREXS, the sources and magnitude of uncertainty associated with transfers of spectral radiance using plaques requires further evaluation in future experiments.

Hooker, Stanford B.↗
NASA NTRS2004

Grid Enabled Geospatial Catalogue Web Service

Geospatial Catalogue Web Service is a vital service for sharing and interoperating volumes of distributed heterogeneous geospatial resources, such as data, services, applications, and their replicas over the web. Based on the Grid technology and the Open Geospatial Consortium (0GC) s Catalogue Service - Web Information Model, this paper proposes a new information model for Geospatial Catalogue Web Service, named as GCWS which can securely provides Grid-based publishing, managing and querying geospatial data and services, and the transparent access to the replica data and related services under the Grid environment. This information model integrates the information model of the Grid Replica Location Service (RLS)/Monitoring & Discovery Service (MDS) with the information model of OGC Catalogue Service (CSW), and refers to the geospatial data metadata standards from IS0 19115, FGDC and NASA EOS Core System and service metadata standards from IS0 191 19 to extend itself for expressing geospatial resources. Using GCWS, any valid geospatial user, who belongs to an authorized Virtual Organization (VO), can securely publish and manage geospatial resources, especially query on-demand data in the virtual community and get back it through the data-related services which provide functions such as subsetting, reformatting, reprojection etc. This work facilitates the geospatial resources sharing and interoperating under the Grid environment, and implements geospatial resources Grid enabled and Grid technologies geospatial enabled. It 2!so makes researcher to focus on science, 2nd not cn issues with computing ability, data locztic~, processir,g and management. GCWS also is a key component for workflow-based virtual geospatial data producing.

Chen, Ai-Jun↗