Search NASA⌕ Search

SEARCH · Search NASA

Results for “SIZE DETERMINATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1951

Comparison of High-Speed Operating Characteristics of Size 215 Cylindrical-Roller Bearings as Determined in Turbojet Engine and in Laboratory Test Rig

A comparison of the operating characteristics of 75-millimeter-bore (size 215) cylindrical-roller one-piece inner-race-riding cage-type bearings was made using a laboratory test rig and a turbojet engine. Cooling correlation parameters were determined by means of dimensional analysis, and the generalized results for both the inner- and outer-race bearing operating temperatures are compared for the laboratory test rig and the turbojet engine. Inner- and outer-race cooling-correlation curves were obtained for the turbojet-engine turbine-roller bearing with the same inner- and outer-race correlation parameters and exponents as those determined for the laboratory test-rig bearing. The inner- and outer-race turbine roller-bearing temperatures may be predicted from a single curve, regardless of variations in speed, load, oil flow, oil inlet temperature, oil inlet viscosity, oil-jet diameter or any combination of these parameters. The turbojet-engine turbine-roller-bearing inner-race temperatures were 30 to 60 F greater than the outer-race-maximum temperatures, the exact values depending on the operating condition and oil viscosity; these results are in contrast to the laboratory test-rig results where the inner-race temperatures were less than the outer-race-maximum temperatures. The turbojet-engine turbine-roller bearing, maximum outer-race circumferential temperature variation was approximately 30 F for each of the oils used. The effect of oil viscosity on inner- and outer-race turbojet-engine turbine-roller-bearing temperatures was found to be significant. With the lower viscosity oil (6x10(exp -7) reyns (4.9 centistokes) at 100 F; viscosity index, 83), the inner-race temperature was approximately 30 to 35 F less than with the higher viscosity oil (53x10(exp -7) reyns (42.8 centistokes) at 100 F; viscosity index, 150); whereas the outer-race-maximum temperatures were 12 to 28 F lower with the lower viscosity oil over the DN range investigated.

BEARINGS, ANTI-FRICTION↗
NASA NTRS1980

A model of the origin of the Jovian ring

Assuming that the micron-sized particles making up the bright Jovian ring are fragments of erosive collisions between micrometeoroid projectiles and large parent bodies, a physical model of the ring is calculated. This leads to a well-defined size distribution for the ejecta, whose optical properties can be compared with observation. The (most likely silicate) ejecta material maximum diameter is estimated to be 0.1 micron, and most likely the result of Io volcanic activity. The impact model's determination of ejecta size distribution in turn determines the structure of the ring, with the largest ejecta forming the bright ring, medium-sized ejecta forming a disk that extends to the Jovian atmosphere, and small ejecta forming a faint halo whose structure is dominated by electromagnetic forces.

Gruen, E.↗
NASA NTRS1952

Comparison of High-Speed Operating Characteristics of Size 215 Cylindrical-Roller Bearings as Determined in Turbojet Engine and in Laboratory Test Rig

A comparison of the operating characteristics of 75-millimeter-bore (size 215) cylindrical-roller one-piece inner-race-riding cage-type bearings was made by means of a laboratory test rig and a turbojet engine. Cooling correlation parameters were determined by means of dimensional analysis, and the generalized results for both the inner- and the outer-race bearing operating temperatures are computed for the laboratory test rig and the turbojet engine. A method is given that enables the designer to predict the inner- and outer-race turbine roller-bearing temperatures from single curves, regardless of variations in speed, load, oil flow, oil inlet temperature, oil inlet viscosity, oil-jet diameter, or any combination of these parameters.

Macks, E Fred↗
NASA NTRS1985

Criteria for software modularization

A central issue in programming practice involves determining the appropriate size and information content of a software module. This study attempted to determine the effectiveness of two widely used criteria for software modularization, strength and size, in reducing fault rate and development cost. Data from 453 FORTRAN modules developed by professional programmers were analyzed. The results indicated that module strength is a good criterion with respect to fault rate, whereas arbitrary module size limitations inhibit programmer productivity. This analysis is a first step toward defining empirically based standards for software modularization.

Card, David N.↗
NASA NTRS2020

The Influence of Frequency and Duration Of Seismic Ground Motion On The Size Of Triggered Landslides—A Regional View

Observation, theory, and intuition all suggest that larger earthquakes should trigger larger landslides. Many factors could contribute to this, including depth-dependent shear strength or non-linearity of ground motion in soils and rock, but we hypothesize that the key characteristics of large earthquakes causing this phenomenon are (in addition to magnitude) the frequency and duration of the strong ground motion. Because of the paucity of site-specific data for detailed analysis, we take a regional approach to this question by analyzing strong-motion records and earthquake-induced landslide (EQIL) inventories from six well-documented earthquakes. Ground motion is characterized using earthquake magnitude and the median durations and frequencies (mean periods) of subsets of strong-motion records relevant to landslide triggering. EQIL inventories are characterized using the median landslide area of the entire inventory as well as the median areas of the largest 1% of the landslides and the largest 10 landslides. We then compare ground-motion characteristics with landslide size statistics to determine possible correlations. Comparisons of all earthquake- and landslide-size statistics show strong positive correlations between landslide size and (1) magnitude, (2) ground-motion duration, and (3) mean period. Although all the ground-motion measures yield highly correlated regressions, mean period appears to be the best overall predictor of landslide size. Landslide modeling using Newmark's sliding-block method also shows that longer mean periods and durations and larger magnitudes correlate strongly with increases in modeled displacements. These results support our hypothesis that increasing period and duration of seismic ground motion are the physical factors driving increased landslide sizes for larger earthquakes. Additional studies including data from a much larger set of earthquakes is needed to confirm the results of this initial study.

Hakan Tanyas↗
NASA NTRS2002

Dynamics and Structure of Planetary Rings

We developed a novel technique to determine the macroscopic particle size distribution of Saturn's rings by exploiting diffraction effects during stellar occultations. This was a major undertaking, and resulted in two publications now in press. In the latter paper, we derived power-law particle size distributions for each of Saturn's main ring regions, using observations of the 3 July 1989 stellar occultation of 28 Sgr from Palomar, McDonald, and Lick Observatories. We used the Voyager PPS delta Sco optical depth profile to estimate and then remove the directly transmitted signal from the 28 Sgr observations, leaving high SNR scattered light profiles at wavelengths of 3.9, 2.1, and 0.9 micrometers. The angular distribution of this diffracted signal depends on the ring particle size distribution: the sharpness of the forward lobe is set by the largest particles, while the overall breadth and amplitude of the scattered signal reflects the abundance of smaller, cm-sized particles. We developed both a simple one-dimensional scattering model and a more realistic 2-D model. We assumed for simplicity a single power law particle size distribution for each major ring region, and determined the index q and lower and upper size cutoffs a(sub min) and a(sub max) that provide the best match to all three data sets in each region. Our results in the A and C Rings are fairly consistent with values of q and a(sub max) derived from Voyager radio occultation (RSS) measurements. We extended their results by determining lower limits to the particle size distributions and by probing the B Ring. This technique is applicable to imaging observations of the rings during the Cassini mission.

French, Richard G.↗
NASA NTRS1992

Sintering time and atmosphere influences on the microstructure and mechanical properties of tungsten heavy alloys

The present paper traces the microstructure and mechanical property variations vs sintering time under conditions where the atmosphere was adjusted to suppress pore generation. Attention is given to tracing the mechanical property links to the grain size under optimized sintering conditions. The optimal cycle is used to sinter two heavy alloy compositions (88 and 95 wt pct W) for times up to 600 minutes at 1480 C. The 88-pct-W samples slumped, but the 95-pct-W samples were fully densified and suitable for tensile testing. At long sintering times, the tungsten grains flattened and the tungsten contiguity decreased, indicating a transition to low-energy configurations for the solid-liquid interfaces. The cube of the mean grain size varied linearly with the isothermal sintering time. This allowed the determination of grain size effects on mechanical properties, showing a decreasing yield strength with increasing time in agreement with the Hall-Petch behavior. The tensile strength and elongation were highest for sintering times from 30 to 90 min, reflecting a minimum in the residual porosity.

German, R. M.↗
NASA NTRS1993

Solid propellant exhausted aluminum oxide and hydrogen chloride - Environmental considerations

Measurements of gaseous hydrogen chloride (HCl) and particulate aluminum oxide (Al2O3) were made during penetrations of five Space Shuttle exhaust clouds and one static ground test firing of a shuttle booster. Instrumented aircraft were used to penetrate exhaust clouds and to measure and/or collect samples of exhaust for subsequent analyses. The focus was on the primary solid rocket motor exhaust products, HCl and Al2O3, from the Space Shuttle's solid boosters. Time-dependent behavior of HCl was determined for the exhaust clouds. Composition, morphology, surface chemistry, and particle size distributions were determined for the exhausted Al2O3. Results determined for the exhaust cloud from the static test firing were complicated by having large amounts of entrained alkaline ground debris (soil) in the lofted cloud. The entrained debris may have contributed to neutralization of in-cloud HCl.

Cofer, W. R., III↗
NASA NTRS1973

A new method for the determination of thin film porosity

Internal reflection spectroscopy may be used to determine presence of water in thin film pores. Presence of water in such pores is function of relative humidity and pore size. Thus, one can determine pore size by controlling humidity. Fluids with surface tension different from that of water can be used to detect pores.

Beck, T. R.↗
NASA NTRS2009

New Measurements of the Particle Size Distribution of Apollo 11 Lunar Soil 10084

We have initiated a major new program to determine the grain size distribution of nearly all lunar soils collected in the Apollo program. Following the return of Apollo soil and core samples, a number of investigators including our own group performed grain size distribution studies and published the results [1-11]. Nearly all of these studies were done by sieving the samples, usually with a working fluid such as Freon(TradeMark) or water. We have measured the particle size distribution of lunar soil 10084,2005 in water, using a Microtrac(TradeMark) laser diffraction instrument. Details of our own sieving technique and protocol (also used in [11]). are given in [4]. While sieving usually produces accurate and reproducible results, it has disadvantages. It is very labor intensive and requires hours to days to perform properly. Even using automated sieve shaking devices, four or five days may be needed to sieve each sample, although multiple sieve stacks increases productivity. Second, sieving is subject to loss of grains through handling and weighing operations, and these losses are concentrated in the finest grain sizes. Loss from handling becomes a more acute problem when smaller amounts of material are used. While we were able to quantitatively sieve into 6 or 8 size fractions using starting soil masses as low as 50mg, attrition and handling problems limit the practicality of sieving smaller amounts. Third, sieving below 10 or 20microns is not practical because of the problems of grain loss, and smaller grains sticking to coarser grains. Sieving is completely impractical below about 5- 10microns. Consequently, sieving gives no information on the size distribution below approx.10 microns which includes the important submicrometer and nanoparticle size ranges. Finally, sieving creates a limited number of size bins and may therefore miss fine structure of the distribution which would be revealed by other methods that produce many smaller size bins.

McKay, D.S.↗
NASA NTRS1993

Effects of an aft facing step on the surface of a laminar flow glider wing

A motor glider was used to perform a flight test study on the effects of aft facing steps in a laminar boundary layer. This study focuses on two dimensional aft facing steps oriented spanwise to the flow. The size and location of the aft facing steps were varied in order to determine the critical size that will force premature transition. Transition over a step was found to be primarily a function of Reynolds number based on step height. Both of the step height Reynolds numbers for premature and full transition were determined. A hot film anemometry system was used to detect transition.

Sandlin, Doral R.↗
NASA NTRS1973

Heat shielding for Venus entry probes.

Two contrasted approaches to ablative thermal protection of Venus entry probes are presented - a typical carbonaceous charring ablator and a dielectric reflective ablator. The interesting observation in this study is that mass loss is not the controlling variable in heat-shield sizing. A heat-soak problem determines the carbon phenolic sizing. For Teflon, the material thickness required to accomplish reflection is the sizing factor. The total heat-shield weight required to handle either steep or shallow entry is computed to be 13% less for a Teflon shield (if at least 3.2 mm are required for reflection) than for a charring ablator shield. If an efficient reflective backing is used with Teflon, the thickness can be reduced 1.0 mm and the computed weight is 31% less for Teflon than for the charring ablator. Such weight reductions may significantly increase the science payload weight of the miniprobes.

Peterson, D. L.↗
NASA NTRS1976

Ocean foam generation and modeling

A laboratory investigation was conducted to determine the physical and microwave properties of ocean foam. Special foam generators were designed and fabricated, using porous glass sheets, known as glass frits, as the principal element. The glass frit was sealed into a water-tight vertical box, a few centimeters from the bottom. Compressed air, applied to the lower chamber, created ocean foam from sea water lying on the frit. Foam heights of 30 cm were readily achieved, with relatively low air pressures. Special photographic techniques and analytical procedures were employed to determine foam bubble size distributions. In addition, the percentage water content of ocean foam was determined with the aid of a particulate sampling procedure. A glass frit foam generator, with pore diameters in the range 70 - 100 micrometers, produced foam with bubble distributions very similar to those found on the surface of natural ocean foam patches.

Porter, R. A.↗
NASA NTRS1987

Performance and operating envelope of imaging and scattering particle sizing instruments

Scattering and imaging type particle sizing instruments are analyzed in terms of their ability to make accurate determinations of particle size distributions, number density, and total mass. Sources of counting and sizing errors are explained. Ways are described of identifying these errors and how these errors can effect the measurements.

Hovenac, Edward A.↗
NASA NTRS1981

Preparation and evaluation of advanced electrocatalysts for phosphoric acid fuel cells

A number of electrocatalyst combinations were prepared and characterized. These electrocatalysts were formulated to contain platinum combined with transition metal carbide forming elements (W, Mo, V) for cathodes and platinum combined with palladium for anodes. High resolution electron microscopy was used to determine the crystallite size and dispersion of platinum-palladium alloy electrocatalysts in order to provide analytical support for the electrochemical determinations of the particle dispersions. An equation was derived which correlates palladium crystallite size with electrochemical hydrogen adsorption. Based on comparisons of electrocatalyst performances in the presence of pure hydrogen and hydrogen containing carbon monoxide, it was shown that the apparent poisoning of the electrocatalyst by carbon monoxide is influenced by the electrode structure.

Stonehart, P.↗