Search NASA⌕ Search

SEARCH · Search NASA

Results for “STOL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Study of aircraft in intraurban transportation systems, volume 3

An investigation of three aircraft concepts, deflected slipstream STOL, helicopter VTOL, and fixed wing STOL, is presented. An attempt was made to determine the best concept for the intraurban transportation system. Desirability of the concept was based on ease of maintenance, development timing, reliability, operating costs, and the noise produced. Indications are that the deflected slipstream STOL is best suited for intraurban transportation. Tables and graphs are included.

Stout, E. G.↗

Fixed-range optimum trajectories for short-haul aircraft

An algorithm, based on the energy-state method, is derived for calculating optimum trajectories with a range constraint. The basis of the algorithm is the assumption that optimum trajectories consist of, at most, three segments: an increasing energy segment (climb); a constant energy segment (cruise); and a decreasing energy segment (descent). This assumption allows energy to be used as the independent variable in the increasing and decreasing energy segments, thereby eliminating the integration of a separate adjoint differential equation and simplifying the calculus of variations problem to one requiring only pointwise extremization of algebraic functions. The algorithm is used to compute minimum fuel, minimum time, and minimum direct-operating-cost trajectories, with range as a parameter, for an in-service CTOL aircraft and for an advanced STOL aircraft. For the CTOL aircraft and the minimum-fuel performance function, the optimum controls, consisting of air-speed and engine power setting, are continuous functions of the energy in both climb and descent as well as near the maximum or cruise energy. This is also true for the STOL aircraft except in the descent where at one energy level a nearly constant energy dive segment occurs, yielding a discontinuity in the airspeed at that energy. The reason for this segment appears to be the relatively high fuel flow at idle power of the engines used by this STOL aircraft. Use of a simplified trajectory which eliminates the dive increases the fuel consumption of the total descent trajectory by about 10 percent and the time to fly the descent by about 19 percent compared to the optimum.

Erzberger, H.↗

Low speed aerodynamic characteristics of a vectored thrust V/STOL transport with two lift/cruise fans

A wind tunnel test was conducted to obtain power on low speed characteristics of a twin fan vectored thrust V/STOL transport aircraft. Longitudinal, as well as some lateral directional data, were analyzed. Hover, STOL, and conventional flight modes were investigated. Determination of STOL characteristics, hover characteristics, roll control effectiveness and aircraft attitude were evaluated. The study also included various means to improve the lifting capability of the aircraft such as by application of fuselage strakes, exhaust vanes capable of shifting the thrust vector aft, and external flap blowing for STOL performance.

Renselaer, D. J.↗

Forward velocity effects on fan noise and the suppression characteristics of advanced inlets as measured in the NASA-Ames 40 by 80 foot wind tunnel

Forward velocity effects on the forward radiated fan noise and on the suppression characteristics of three advanced inlets relative to a baseline cylindrical inlet were measured in the NASA Ames Research Center 40 x 80 foot Wind Tunnel. A modified JT15D turbofan engine in a quiet nacelle was the source of fan noise; the advanced inlets were a Conventional Takeoff/Landing (CTOL) hybrid inlet, a Short Takeoff/Landing (STOL) hybrid inlet, and a treated deflector inlet. Also measured were the static to flight effects on the fan noise of canting the baseline inlet 4 deg downward to simulate typical wing mounted turbofan engines. The CTOL hybrid inlet suppressed the high tip speed fan noise as much as 18 PNdB on a 61 m (200 ft) sideline scaled to a CF6 size engine while the STOL hybrid inlet suppressed the low tip speed fan noise as much as 13 PNdB on a 61 m (200 ft) sideline scaled to a OCSEE size engine. The deflector inlet suppressed the high tip speed fan noise as much as 13 PNdB at 61 m (200 ft) overhead scaled to a CF6 size engine. No significant changes in fan noise suppression for the CTOL and STOL hybrid inlets occurred for forward velocity changes above 21 m/s (68 ft/s) or for angle of attack changes up to 15 deg. However, changes in both forward velocity and angle of attack changed the deflector inlet noise unpredictably due to the asymmetry of the inlet flow field into the fan.

Moore, M. T.↗

An investigation of the use of a propulsive wing/canard concept for improved maneuvering

The propulsive wing concept is an extension of the flap boundary layer control utilized on several aircraft configurations. Several studies have been made regarding the benefits of the propulsive wing in STOL operation. However, the propulsive wing/canard provides performance benefits also in areas other than STOL. It is expected to improve the maneuvering capability by providing reduced drag at high lift coefficients without appreciably affecting the low lift drag. An increase in the buffet free load factor can also be expected with the blown wing and canard. Attention is given to a program to investigate the wing/canard at maneuvering conditions, and tests at ranges of blowing coefficients equivalent to STOL operation.

Stewart, V. R.↗

Large-scale static investigation of circulation-control-wing concepts applied to upper surface-blowing aircraft

The use of a circulation control to deflect turbofan engine thrust beyond 90 deg. has been proven in full-scale static ground tests of the circulation-control-wing/upper-surface-blowing (CCW/USB) concept. This powered high-lift system employs a circular, blown trailing edge to replace the USB mechanical flaps to entrain engine-exhaust flow, and to obtain both a vertical-thrust component and an augmented circulation lift for short takeoff and landing (STOL) applications. Previous tests (Phase 1), done in 1982, of a basic configuration installed on the Quiet Short Haul Research Aircraft confirmed these CCW/USB systems capabilities. A second phase (Phase 2) of full-scale, static, thrust-deflection investigations has reconfirmed the ability to deflect engine thrust from 40 to 102 deg., depending on thrust level. Five new configurations were evaluated and performance improvements noted for those configurations with larger blown span, fences or favorable engine interactions, smaller slot height, and larger radii with less than 180 deg. of CCW surface arc. In general, a 90 deg. circular arc with a smaller slot height provided the best performance, demonstrating that adequate thrust turning can be produced by a trailing-edge shape which may have minimal cruise-performance penalty. Thrust deflections were achieved at considerably lower blowing momentum than was required for the baseline case of Phase 1. Improved performance and versatility were thus confirmed for the CCW/USB system applied to STOL aircraft, where the potential for developing a non-moving-parts pneumatic thrust deflector to rapidly vary horizontal force from thrust to drag, while maintaining constant vertical force, appears quite promising. The conversion from high-lift to lower-drag cruise mode by merely terminating the blowing provides an effective STOL aircraft system.

Shovlin, M. D.↗

Functional description of a command and control language tutor

The status of an ongoing project to explore the application of Intelligent Tutoring System (ITS) technology to NASA command and control languages is described. The primary objective of the current phase of the project is to develop a user interface for an ITS to assist NASA control center personnel in learning Systems Test and Operations Language (STOL). Although this ITS will be developed for Gamma Ray Observatory operators, it will be designed with sufficient flexibility so that its modules may serve as an ITS for other control languages such as the User Interface Language (UIL). The focus of this phase is to develop at least one other form of STOL representation to complement the operational STOL interface. Such an alternative representation would be adaptively employed during the tutoring session to facilitate the learning process. This is a key feature of this ITS which distinguishes it from a simulator that is only capable of representing the operational environment.

Elke, David R.↗

Hypermedia and intelligent tutoring applications in a mission operations environment

Hypermedia, hypertext and Intelligent Tutoring System (ITS) applications to support all phases of mission operations are investigated. The application of hypermedia and ITS technology to improve system performance and safety in supervisory control is described - with an emphasis on modeling operator's intentions in the form of goals, plans, tasks, and actions. Review of hypermedia and ITS technology is presented as may be applied to the tutoring of command and control languages. Hypertext based ITS is developed to train flight operation teams and System Test and Operation Language (STOL). Specific hypermedia and ITS application areas are highlighted, including: computer aided instruction of flight operation teams (STOL ITS) and control center software development tools (CHIMES and STOL Certification Tool).

Ames, Troy↗

Evaluation of Four Advanced Nozzle Concepts for Short Takeoff and Landing Performance

Four advanced nozzle concepts were tested on a canard-wing fighter in the Langley 14- by 22-Foot Subsonic Tunnel. The four vectoring-nozzle concepts were as follows: (1) an axisymmetric nozzle (AXI); (2) an asymmetric, load balanced exhaust nozzle (ALBEN); (3) a low aspect ratio, single expansion ramp nozzle (LASERN); and (4) a high aspect ratio, single expansion ramp nozzle (HASERN). The investigation was conducted to determine the most suitable nozzle concept for short takeoff and landing (STOL) performance. The criterion for the best STOL performance was a takeoff ground roll of less than 1000 ft. At approach, the criteria were high lift and sufficient drag to maintain a glide slope of -3 to -6 deg with enough pitching-moment control from the canards. The test was performed at a dynamic pressure of 45 lb/sq ft and an angle-of-attack range of 0 to 20 deg. The nozzle pressure ratio was varied from 1.0 to 4.3 at both dry power and after burning nozzle configurations with nozzle vectoring to 60 deg. In addition, the model was tested in and out of ground effects. The ALBEN concept was the best of the four nozzle concepts tested for STOL performance.

Quinto, P. Frank↗

Quiet Cruise Efficient Short Take-off and Landing Subsonic Transport System

This NASA funded study conceived a revolutionary airplane concept to enable future traffic growth by using regional air space. This requires a very quiet airplane with STOL capability. Starting with a Blended Wing Body that is cruise efficient with inherent low noise characteristics from forward noise shielding and void of aft downward noise reflections, integration of embedded distributed propulsion enables incorporation of the revolutionary concept for jet noise shielding. Embedded distributed propulsion also enables incorporation of a fan bleed internally blown flap for quiet powered lift. The powered lift provides STOL capability for operation at regional airports with rapid take-off and descent to further reduce flyover noise. This study focused on configuring the total engine noise shielding STOL concept with a BWB airplane using the Boeing Phantom Works WingMOD multidisciplinary optimization code to define a planform that is pitch controllable. The configuration was then sized and mission data developed to enable NASA to assess the flyover and sideline noise. The foundational technologies needed are identified including military dual use benefits.

Kawai, Ron↗

Peak axial-velocity decay with single- and multi-element nozzles

Jet peak-velocity decay data were obtained for a variety of circular and noncircular single-element and multi-element nozzles for application to externally-blown-flap (EBF) STOL aircraft. These data permit a rational approach, in terms of element type and element spacing, to nozzles designed to promote mixing of the jet exhaust with the surrounding air. Rapid mixing and the resulting lower axial jet velocity decreases the noise caused by the interaction of jet impingement on the flap assembly of EBF STOL aircraft. Empirical relationships are presented that permit the prediction of peak axial-velocity decay curves for a wide spectrum of mixer-type nozzles. The data are useful also in the design of ejector-type noise suppressors and for the suppression of VTOL downwash velocities caused by vertically oriented exhaust nozzles.

Vonglahn, U. H.↗

Noise produced by a small-scale, externally blown flap

Noise data were obtained with a model of an externally blown flap of the type that is currently being considered for STOL aircraft. The noise caused by impingement of the jet on the flap is much louder than the nozzle jet noise. It is especially so directly below the wing. The noise level increases as the jet velocity and flap angle are increased. The sound power level increased with the sixth power of velocity. Several physical variations to the STOL model configuration were also tested. Two such variations, a large board and a slotless curved plate wing, had the same power spectra density (Strouhal number curve) as the model.

Olsen, W. A.↗

Study of an intraurban travel demand model incorporating commuter preference variables

The model is based on the substantial travel data base for the nine-county San Francisco Bay Area, provided by the Metropolitan Transportation Commission. The model is of the abstract type, and makes use of commuter attitudes towards modes and simple demographic characteristics of zones in a region to predict interzonal travel by mode for the region. A characterization of the STOL/VTOL mode was extrapolated by means of a subjective comparison of its expected characteristics with those of modes characterized by the survey. Predictions of STOL demand were made for the Bay Area and an aircraft network was developed to serve this demand. When this aircraft system is compared to the base case system, the demand for STOL service has increased five fold and the resulting economics show considerable benefit from the increased scale of operations. In the previous study all systems required subsidy in varying amounts. The new system shows a substantial profit at an average fare of $3.55 per trip.

Holligan, P. E.↗

Measured noise of model fan-under-wing and fan-on-flap jet flap configurations

Noise measurements were made on two jet flap systems proposed for STOL aircraft. In one case a 14.0-cm- (5.5-in.-) diameter fan was mounted under the wing such that the exhaust impinged on downwardly deflected flap segments. In the other case, the fan was located on the upper surface of the flap such that fan and flap moved as a unit, with no exhaust impingement. Results for takeoff and approach fan speeds and flap deflections were used to estimate STOL airplane perceived noise levels. Internally generated noise directivity corresponded with fan axis orientation for the fan-on-flap, but no consistent redirection of internal noise was observed with changes in flap angle for the fan-under-wing. With the fan-on-flap arrangement, the wing shielded some fan inlet noise from the ground. Since no impingement of the exhaust on solid surfaces occurred, the external noise was jet noise alone. In contrast, for the fan-under-wing, the jet/flap interaction noise dominated the external noise except at angles near the jet axis even with no flap deflection. If internal noise is reduced by fan design and acoustic treatment, the jet/flap interaction noise will dominate.

Groeneweg, J. F.↗

Study of aircraft in intraurban transportation systems

A systems analysis was conducted to define the technical economic and operational characteristics of an aircraft transportation system for short-range intracity commutor operations. The analysis was for 1975 and 1985 in the seven county, Detroit, Michigan area. STOL and VTOL aircraft were studied in sizes from 40 to 120 passengers. The preferred vehicle for the Detroit area was the deflected slipstream STOL. Since the study was parametric in nature, it is applicable to generalization, and it was concluded that a feasible intraurban air transportation system could be developed in many viable situations.

Stout, E. G.↗

Peak axial-velocity decay with single- and multi-element nozzles.

Jet peak-velocity decay data were obtained for a variety of circular and noncircular single-element and multi-element nozzles for application to externally-blown-flap STOL aircraft. These data permit a rational approach, in terms of element type and element spacing, to nozzles designed to promote mixing of the jet exhaust with the surrounding air. Rapid mixing and the resulting lower axial jet velocity decreases the noise caused by the interaction of jet impingement on the flap assembly of EBF STOL aircraft. Empirical relationships are presented that permit the prediction of peak axial-velocity decay curves for a wide spectrum of mixer-type nozzles. The data are useful also in the design of ejector-type noise suppressors and for the suppression of VTOL downwash velocities caused by vertically oriented exhaust nozzles.

Von Glahn, U. H.↗

Flight evaluations of the effect of advanced control systems and displays on the handling qualities of a general aviation airplane.

Flight tests have shown that, by means of improved displays and advanced control systems, it is possible to transform a typical light airplane into a flying machine that borders on being perfect from a handling-qualities standpoint. A flight-director display and an attitude-command control system used in combination transformed a vehicle with poor handling qualities during ILS approaches in turbulent air into a vehicle with extremely good handling qualities. The attitude-command control system also improved the ride qualities of the airplane. A rate-command control system was less beneficial than an attitude-command control system. Although this paper deals primarily with general aviation aircraft, the results presented pertain to other types of aircraft. Short-takeoff-and-landing (STOL) aircraft would be a natural application of the control systems because, as a result of their low speeds, they encounter many of the handling-qualities problems noted on light aircraft. The improved ride qualities should be of interest to all airline operations, and for STOL aircraft in particular, because of their prolonged exposure to low-altitude turbulence.

Loschke, P. C.↗

Experimental performance of cascade thrust reversers at forward velocity

A series of static and wind tunnel tests were performed on four cowl cascade thrust reverser configurations which had various reversed jet emission patterns applicable to an externally blown flap STOL aircraft. The work was performed using a model fan which was 14.0 cm in diameter and passed a fan mass flow of 2.49 kg/sec at an approximate fan pressure ratio of 1.22 and fan corrected rotational speed of 35,800 rpm. The tests demonstrated that the reingestion of fan flow significantly reduced the reverser efficiency and that the thrust reverser efficiency was improved by reducing the reversed jet azimuthal emmission angle. The reverser efficiency at STOL landing speeds was as high as 0.95; however, configurations with lateral emission were adversely affected by yawing the nacelle at forward velocity. Measurements of the internal static pressure at the stator exit showed significant increases in the local static pressure for configurations with reduced jet emission angles.

Dietrich, D. A.↗