Search NASA⌕ Search

SEARCH · Search NASA

Results for “SURFACE GEOMETRY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Numerical evaluation of the radiation from unbaffled, finite plates using the FFT

An iteration technique is described which numerically evaluates the acoustic pressure and velocity on and near unbaffled, finite, thin plates vibrating in air. The technique is based on Rayleigh's integral formula and its inverse. These formulas are written in their angular spectrum form so that the fast Fourier transform (FFT) algorithm may be used to evaluate them. As an example of the technique the pressure on the surface of a vibrating, unbaffled disk is computed and shown to be in excellent agreement with the exact solution using oblate spheroidal functions. Furthermore, the computed velocity field outside the disk shows the well-known singularity at the rim of the disk. The radiated fields from unbaffled flat sources of any geometry with prescribed surface velocity may be evaluated using this technique. The use of the FFT to perform the integrations in Rayleigh's formulas provides a great savings in computation time compared with standard integration algorithms, especially when an array processor can be used to implement the FFT.

Williams, E. G.↗
NASA NTRS1973

Drift shell splitting by internal geomagnetic multipoles.

Computations on an 80-coefficient model of the earth's field illustrate the 'topography' of the magnetic equatorial surface and the geometry of the drift shells of geomagnetically trapped particles. Individual terms in the spherical harmonic expansion of the geomagnetic scalar potential V(r, theta, phi) are either even or odd in cos theta, where theta = 90 deg denotes the dipole equator. Terms that are even in cos theta tend to 'warp' the equatorial surface, but do not (in first order) distort particle drift shells radially nor split the drift shells of particles having different equatorial pitch angles. Azimuthally asymmetric terms that are odd in cos theta do cause shell splitting in first order. Shell splitting at large L values (neglecting deformation of the earth's field by the solar wind) is found to be dominated by the geomagnetic octupole. At L approximately equal to 1, shell splitting is strongly enhanced by the South American and South African anomalies. When combined with pitch angle diffusion caused by atmospheric scattering, these results may be able to account for anomalous radial diffusion of inner zone electrons.

Roederer, J. G.↗
DOE OSTI2026

Reaction Diffusion Modelling of 3D Pillar Electrodes in Single-Catalyst CO 2 Reduction Cascades

Effective electrochemical CO 2 reduction to liquid fuels requires that the local catalytic environment facilitates the desired reactivity, yet a microscopic understanding of this environment is difficult to achieve from experiment alone. In this work, a 3D reaction-diffusion model was developed to explore the effects of electrode surface area and local geometry on the performance of a heterogeneous catalyst that performs a two-step CO 2 reduction cascade reaction to CO and then CH 3 OH under aqueous conditions. Kinetic parameters for the model were inspired by experimental results using a cobalt phthalocyanine (CoPc) catalyst. Three-dimensional architectures composed of arrays of square pillars with varying dimensions and either smooth or periodically modulated surfaces were tested, revealing the extent to which geometry modulates the performance of the cascade reactions. Although structural variations modulate local concentration gradients, we find that electrochemically active surface area predominantly governs the overall cascade reaction. Moreover, the results suggest that supersaturation of CO, with concentrations up to ten-fold higher than the equilibrium solubility limit, might be critical for more efficient conversion to CH 3 OH. For any given geometry, the spatially averaged ratio of [CO] to [CO 2 ] is dictated by the electrochemically active surface area and determines the yield of CH 3 OH. For a fixed surface area, geometries that spatially confine the electrolyte yield moderate local [CO] to [CO 2 ] ratios within small volumes. In contrast, less confining geometries result in a broader distribution of local ratios spread over larger volumes, with both configurations yielding the same spatially averaged [CO] to [CO 2 ] ratio. These insights provide valuable design principles—highlighting the critical importance of surface area and possibly CO supersaturation—for engineering advanced electrode architectures that leverage intermediate trapping and CO supersaturation to enhance overall performance in tandem CO 2 reduction systems.

COMSOL↗
NASA NTRS1979

Photopolarimetry of scattering surfaces and their interpretation by computer model

Wolff's computer model of a rough planetary surface was simplified and revised. Close adherence to the actual geometry of a pitted surface and the inclusion of a function for diffuse light resulted in a quantitative model comparable to observations by planetary satellites and asteroids. A function is also derived to describe diffuse light emitted from a particulate surface. The function is in terms of the indices of refraction of the surface material, particle size, and viewing angles. Computer-generated plots describe the observable and theoretical light components for the Moon, Mercury, Mars and a spectrum of asteroids. Other plots describe the effects of changing surface material properties. Mathematical results are generated to relate the parameters of the negative polarization branch to the properties of surface pitting. An explanation is offered for the polarization of the rings of Saturn, and the average diameter of ring objects is found to be 30 to 40 centimeters.

Wolff, M.↗
NASA NTRSDate not supplied

Ab Initio Electronic Structure Calculations of CNN for CN Excitation Studies

The CN molecule is an important contributor to radiative heat flux in shock layers around vehicles entering Titan’s atmosphere. Current data for heavy particle (de)excitation rate coefficients of CN leads to uncertainties in the population of CN in its first and second excited states. This in turn leads to uncertainties in the radiative heat flux predicted by Computational Fluid Dynamics (CFD) simulations of Titan atmospheric entry. This work performs ab initio electronic structure calculations of the CNN complex to create Potential Energy Surfaces (PESs) that correlate to the ground and first and second excited states of CN. Specifically, the state combinations of CN(X,A,B) + N(4S𝑜) correlate to six states of CNN (three Quintet A” and three Triplet A”). Initial calculations of these states suggest that heavy particle (de)excitation of CN by N atoms is likely to proceed through collinear geometries on triplet surfaces. Complete PESs will show all of the reaction pathways in detail, and will be used in nonadiabatic dynamics calculations to evaluate improved rate coefficients and reduce uncertainty in the radiative heat flux during Titan entry.

Eric C Geistfeld↗
NASA NTRSDate not supplied

Ab Initio Electronic Structure Calculations of CNN for CN Excitation Studies

The CN molecule is an important contributor to radiative heat flux in shock layers around vehicles entering Titan’s atmosphere. Current data for heavy particle (de)excitation rate coefficients of CN leads to uncertainties in the population of CN in its first and second excited states. This in turn leads to uncertainties in the radiative heat flux predicted by Computational Fluid Dynamics (CFD) simulations of Titan atmospheric entry. This work performs ab initio electronic structure calculations of the CNN complex to create Potential Energy Surfaces (PESs) that correlate to the ground and first and second excited states of CN. Specifically, the state combinations of CN(X,A,B) + N(4S𝑜) correlate to six states of CNN (three Quintet A” and three Triplet A”). Initial calculations of these states suggest that heavy particle (de)excitation of CN by N atoms is likely to proceed through collinear geometries on triplet surfaces. Complete PESs will show all of the reaction pathways in detail, and will be used in nonadiabatic dynamics calculations to evaluate improved rate coefficients and reduce uncertainty in the radiative heat flux during Titan entry.

Eric Geistfeld↗
NASA NTRS2001

Heat Transfer and Flow on the Blade Tip of a Gas Turbine Equipped with a Mean-Camberline Strip

Experimental and computational studies have been performed to investigate the detailed distribution of convective heat transfer coefficients on the first-stage blade tip surface for a geometry typical of large power generation turbines (greater than 100 MW) In a previous work the numerical heat transfer results for a sharp edge blade tip and a radiused blade tip were presented. More recently several other tip treatments have been considered for which the tip heat transfer has been measured and documented. This paper is concerned with the numerical prediction of the tip surface heat transfer for radiused blade tip equipped with mean-camberline strip (or "squealer" as it is often called). The heat transfer results are compared with the experimental results and discussed. The effectiveness of the mean-camberline strip in reducing the tip leakage and the tip heat transfer as compared to a radiused edge tip and sharp edge tip was studied. The calculations show that the sharp edge tip works best (among the cases considered) in reducing the tip leakage flow and the tip heat transfer.

Ameri, A.A.↗
NASA NTRS2018

Measuring Work of Adhesion of Polystyrene Microspheres

Particle adhesion is relevant in fields ranging from aerospace and energy to civil engineering and medicine. The functions of aerodynamic surfaces, heat exchangers, solar panels, ventilation systems, and blood vessels are affected by the buildup of particulates on their surfaces. Direct measurement of the adhesive force between a particle and a surface is key to understanding and mitigating particle fouling. Approaches such as the Johnson-Kendall-Roberts (JKR) and Derjaguin-Muller-Toporov (DMT) models offer a first approximation of the forces involved but do not account for non-idealities like roughness or plastic deformation. Experimental measurements of adhesive forces often deviate significantly from predictions. One approach to measure adhesion is the colloidal probe technique, which uses a particle attached to the tip of an atomic force microscope (AFM) cantilever. The particle is touched to a surface and then withdrawn and a pull-off force (FPO) determined by cantilever deflection. FPO can be used to estimate work of adhesion (Wa) and other properties from existing models. We describe a new method for producing colloidal probes using wax as an adhesive to attach micrometer-scale spheres to AFM tips. This method can be used with a range of particles and minimizes the potential for changes to the particle surface chemistry or geometry from exposure to heat, chemicals, radiation, or external forces. Particle attachment to AFM tips is robust and reversible, allowing old particles to be replaced with new ones in a few minutes. Pull-off measurements using polystyrene (PS) particles, pristine and modified with myristyltrimethylammonium bromide (14-TAB), were collected from various substrates to demonstrate the viability of this technique and investigate the impact of particle surface modification.

Schmitz, Russell C.↗
NASA NTRS1988

Flexural behavior of the continental lithosphere in Italy - Constraints imposed by gravity and deflection data

This paper presents a simple model that describes the geometry of subducted continental lithosphere as the result of flexural loading of a thin elastic sheet. The method involves a procedure for systematically matching the plate flexure and gravity data to the best-fitting two-dimensional flexural geometry obtained by a thin elastic sheet of specified elastic strength. It is shown that the model can explain both the deflection of the lithosphere and the gravity anomalies observed along four profiles across the Apennine convergent system in Italy. The results of calculations suggest that in subduction systems, like the Apennines, that are characterized by backarc extension, forces acting on subducted lithosphere at depth can be expressed at the surface in the geometry of the foredeep basin that forms adjacent to the subduction zone.

Royden, Leigh↗
NASA NTRS1981

Dynamics of solid dispersions in oil during the lubrication of point of contacts. Part 2: Molybdenum disulfide

A Hertzian contact consisting of a steel ball in contact with a glass disk is lubricated with MoS2 dispersions and observed by optical microscopy at various slide/roll conditions. In general the behavior of MoS2 and graphite are similar. That is, the solids tend to enter the contact and form a film on the contacting surfaces whenever a rolling component of motion is used, but solid particles seldom enter the contact during pure sliding. The MoS2 has more pronounced plastic flow behavior than graphite. However, the polished steel ball is more readily scratched by MoS2 than by graphite. Under the conditions of these studies, lower friction and wear are observed with pure oil rather than with the dispersions. However under other conditions (such as different contact geometry or rougher surfaces) the solid lubricant dispersions might be beneficial.

Cusano, C.↗
NASA NTRS1987

Multisensor comparison of ice concentration estimates in the marginal ice zone

Aircraft remote sensing data collected during the 1984 summer Marginal Ice Zone Experiment in the Fram Strait are used to compare ice concentration estimates derived from synthetic aperture radar (SAR) imagery, passive microwave imagery at several frequencies, aerial photography, and spectral photometer data. The comparison is carried out not only to evaluate SAR performance against more established techniques but also to investigate how ice surface conditions, imaging geometry, and choice of algorithm parameters affect estimates made by each sensor.Active and passive microwave sensor estimates of ice concentration derived using similar algorithms show an rms difference of 13 percent. Agreement between each microwave sensor and near-simultaneous aerial photography is approximately the same (14 percent). The availability of high-resolution microwave imagery makes it possible to ascribe the discrepancies in the concentration estimates to variations in ice surface signatures in the scene.

Burns, B. A.↗
NASA NTRS1997

PSP Testing at NASA Ames Research Center

Pressure sensitive paints (PSPs) are now used routinely for measuring surface pressures on wind tunnel models at transonic and supersonic Mach numbers. The method utilizes a surface coating containing fluorescent or phosphorescent materials, the brightness of which varies with the local air pressure on the surface. The present paper will summarize PSP activities (in progress and planned) at the NASA Ames Research Center. One of the main accomplishments at NASA Ames has been the development of a PSP measurement system that is production testing capable. This system has been integrated successfully into the large-scale wind tunnel facilities at Ames. There are several problems related to PSP testing which are unique to large-scale wind tunnel testing. The hardware is often difficult to set-up and must operate under harsh conditions (e.g. high pressures and low temperatures). The data acquisition and reduction times need to be kept to a minimum so that the overall wind tunnel productivity is not compromised. The pressure sensitive paints needs to be very robust; the paints must readily adhere to different surfaces with varying geometries and remain functional for long running times. The paint must have well understood, and preferably minimal, temperature sensitivity since fine control of the tunnel temperature is not easily achievable in the larger wind tunnels. In an effort to improve the overall accuracy of the PSP technique, we are currently evaluating some referenced pressure sensitive paints which contain a pressure- independent luminophor in addition to the one which is affected by the surface pressure. The two luminophors are chosen so that their emission wavelengths are somewhat different. Then by taking two 'wind-on' images with either two cameras (with different filters) or one camera with a rotating filter system, the need for 'wind-off' images can be eliminated. The ratio of the two wind-on images accounts for nonuniform lighting and model motion problems (physical movement of the model under aerodynamic loading) are not a concern any more. The paints and data acquisition and reduction software for this type of a PSI system are currently under development and evaluation. Additional information is contained within the original extended abstract.

Bell, J. H.↗
NASA NTRS2007

NASA Lunar Base Wireless System Propagation Analysis

There have been many radio wave propagation studies using both experimental and theoretical techniques over the recent years. However, most of studies have been in support of commercial cellular phone wireless applications. The signal frequencies are mostly at the commercial cellular and Personal Communications Service bands. The antenna configurations are mostly one on a high tower and one near the ground to simulate communications between a cellular base station and a mobile unit. There are great interests in wireless communication and sensor systems for NASA lunar missions because of the emerging importance of establishing permanent lunar human exploration bases. Because of the specific lunar terrain geometries and RF frequencies of interest to the NASA missions, much of the published literature for the commercial cellular and PCS bands of 900 and 1800 MHz may not be directly applicable to the lunar base wireless system and environment. There are various communication and sensor configurations required to support all elements of a lunar base. For example, the communications between astronauts, between astronauts and the lunar vehicles, between lunar vehicles and satellites on the lunar orbits. There are also various wireless sensor systems among scientific, experimental sensors and data collection ground stations. This presentation illustrates the propagation analysis of the lunar wireless communication and sensor systems taking into account the three dimensional terrain multipath effects. It is observed that the propagation characteristics are significantly affected by the presence of the lunar terrain. The obtained results indicate the lunar surface material, terrain geometry and antenna location are the important factors affecting the propagation characteristics of the lunar wireless systems. The path loss can be much more severe than the free space propagation and is greatly affected by the antenna height, surface material and operating frequency. The results from this paper are important for the lunar wireless system link margin analysis in order to determine the limits on the reliable communication range, achievable data rate and RF coverage performance at planned lunar base work sites.

Hwu, Shian U.↗
DOE OSTI2024

Heuristic algorithms for design of integrated monitoring of geologic carbon storage sites

Designs for Risk Evaluation and Management (DREAM) is a tool developed under the National Risk Assessment Partnership (NRAP) to enhance geologic carbon storage safety and efficiency. Using potential leakage scenarios generated externally by the users preferred history-matching approach, DREAM constructs ideal combinations of sensor locations in the right place at the right time to detect as many leaks as possible, detect them as early as possible, and minimize cost. This user-friendly tool, developed in Java, features a window-based GUI for input and a 3D visualization tool for viewing the domain space and optimized monitoring plans. DREAM's latest version accommodates real-world usage by allowing for joint optimization of wellbore point sensor placements and surface geophysics survey geometries, and by using more efficient multi-objective optimization algorithms. We show an example where, these two improvements combined allow us to support containment assurance and go from detecting 80–90 % of the potential CO 2 leakage to +99.7 %, a step-change improvement that can make the deciding difference in whether a site is suitable for geologic carbon storage. Though developed for geologic carbon storage, this tool would be equally applicable in many surface or offshore environmental monitoring projects.

58 GEOSCIENCES↗
DOE OSTI2020

The role of high-order electron correlation effects in a model system for non-valence correlation-bound anions

The diffusion Monte Carlo (DMC), auxiliary field quantum Monte Carlo (AFQMC), and equation-of-motion coupled cluster (EOM-CC) methods are used to calculate the electron binding energy (EBE) of the non-valence anion state of a model (H2O)4 cluster. Two geometries are considered, one at which the anion is unbound and the other at which it is bound in the Hartree–Fock (HF) approximation. It is demonstrated that DMC calculations can recover from the use of a HF trial wave function that has collapsed onto a discretized continuum solution, although larger EBEs are obtained when using a trial wave function for the anion that provides a more realistic description of the charge distribution and, hence, of the nodal surface. For the geometry at which the cluster has a non-valence correlation-bound anion, both the inclusion of triples in the EOM-CC method and the inclusion of supplemental diffuse d functions in the basis set are important. DMC calculations with suitable trial wave functions give EBE values in good agreement with our best estimate EOM-CC result. AFQMC using a trial wave function for the anion with a realistic electron density gives a value of the EBE nearly identical to the EOM-CC result when using the same basis set. For the geometry at which the anion is bound in the HF approximation, the inclusion of triple excitations in the EOM-CC calculations is much less important. The best estimate EOM-CC EBE value is in good agreement with the results of DMC calculations with appropriate trial wave functions.

Upadhyay, Shiv (ORCID:0000000285010501)↗
NASA NTRS1993

Flow transition with 2-D roughness elements in a 3-D channel

We develop a new numerical approach to study the spatially evolving instability of the streamwise dominant flow in the presence of roughness elements. The difficulty in handling the flow over the boundary surface with general geometry is removed by using a new conservative form of the governing equations and an analytical mapping. The numerical scheme uses second-order backward Euler in time, fourth-order central differences in all three spatial directions, and boundary-fitted staggered grids. A three-dimensional channel with multiple two-dimensional-type roughness elements is employed as the test case. Fourier analysis is used to decompose different Fourier modes of the disturbance. The results show that surface roughness leads to transition at lower Reynolds number than for smooth channels.

Liu, Zhining↗
NASA NTRS1989

Electromagnetic properties of material coated surfaces

The electromagnetic properties of material coated conducting surfaces were investigated. The coating geometries consist of uniform layers over a planar surface, irregularly shaped formations near edges and randomly positioned, electrically small, irregularly shaped formations over a surface. Techniques to measure the scattered field and constitutive parameters from these geometries were studied. The significance of the scattered field from these geometries warrants further study.

Beard, L.↗
NASA NTRSDate not supplied

Transfer function models for using empirical and physics-based simulation signal response data

In many situations, real or induced flaws such as tight cracks with known morphology cannot be manufactured in part geometry specimens or in real parts. Typically, surface fatigue cracks are manufactured in simple geometry specimens such as flat plates, dog-bone shaped flat or cylindrical specimens. If a nondestructive evaluation (NDE)technique is required to provide a reliably detectable flaw size, denoted asa90/95, for induced flaws in a part, then a direct method for qualifying the NDE procedure is to use appropriate induced flaw specimens and perform NDE procedure demonstration on the specimens. Probability of detection (POD)analysis of the empirical data may provide estimation of a90/95. This approach is described as direct POD demonstration testing, which may follow guidelines of MIL-HDBK-1823. This paper considers a case, where embedded tight cracklike induced flaws are to be detected reliably using a signal response based NDE procedure. Here, it is assumed that it is not practical to make surface or embedded induced flaw specimens in part geometry or configuration. Therefore, a direct POD demonstration testing cannot be undertaken. It is also assumed that simulation of signal response is possible for both surface and embedded induced flaws in part geometry specimens using a physics-based model. The proposed approach for NDE procedure qualification uses artificial flaws in simple geometry and part geometry specimens, and induced flaws in the same type of simple geometry specimens. Signal response data is taken on all sets of artificial and induced flaws in simple geometry and part geometry specimens. Moreover, simulated signal response data is generated for surface and embedded flaws. Thus, a case of five signal response versus flaw size datasets is considered. Three of the datasets are empirical and two datasets are physics model-based simulation datasets. A method of devising and using transfer function calculation dataset blocks to estimate the either the reliably detectable flaw size or the demonstration flaw size is provided.

Nondestructive evaluation↗