Search NASA⌕ Search

SEARCH · Search NASA

Results for “SWEEP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Divergence study of a high-aspect ratio, forward-swept wing

A study has been conducted in the NASA-Langley Transonic Dynamics wind tunnel to determine the divergence characteristics of a high aspect ratio forward swept wing of rectangular planform, for sweep angles of zero, -15, -30, -45, and -60 deg. In addition to a rectangular wingtip, a tip whose geometry lay parallel with the freestream flow was tested at a sweep angle of -45 deg. The primary objective was to obtain data that could be used to verify the divergence prediction capabilities of an aeroelastic analysis code employing kernel function aerodynamics. The analytical predictions of convergence were found to be conservative for all forward sweep angles, and the effect of the two tip shapes on divergence dynamic pressure were accurately predicted.

Cole, S. R.↗
NASA NTRS1985

Flight characteristics of the AD-1 oblique-wing research aircraft

The AD-1 is a low-speed oblique-wing research airplane. This report reviews the vehicle's basic flight characteristics, including many aerodynamic, stability, and control effects that are unique to an oblique-wing configuration. These effects include the change in sideforce with angle of attack, moment changes with angle of attack and load factor, initial stall on the trailing wing, and inertial coupling caused by a roll-pitch cross product of inertia. An assessment of the handling qualities includes pilot ratings and comments. Ratings were generally satisfactory through 30 deg of wing sweep but degraded with increased sweep. A piloted simulation study indicated that a basic rate feedback control system could be used to improve the handling qualities at higher wing sweeps.

Sim, Alex G.↗
NASA NTRS1987

Pressure distributions and oil-flow patterns for a swept circulation-control wing

Pressure distributions and photographs of oil flow patterns are presented for a circulation control wing. The model was an aspect ratio four semispan wing mounted on the side wall of the NASA Ames Transonic Wind Tunnel. The airfoil was a 20 percent thick ellipse, modified with circular leading and trailing edges of 4 percent radius, and had a 25.4 cm constant chord. This configuration does not represent a specific wing design, but is generic. A full span, tangetial, rearward blowing, circulation control slot was incorporated ahead of the trailing edge on the upper surface. The wing was tested at Mach numbers from 0.3 to 0.75 at sweep angle of 0 to 45 deg with internal to external pressure ratios of 1.0 to 3.0. Lift and pitching momemt coefficients were obtained from measured pressure distributions at five span stations. When the conventional corrections resulting from sweep angle are applied to the lift and moment of circulation control sections, no additional corrections are necessary to account for changes in blowing efficiency. This is demonstrated for an aft sweep angle of 45 deg. An empirical technique for estimating the downwash distribution of a swept wing was validated.

Keener, Earl R.↗
NASA NTRS1988

Aeroelastic modeling of rotor blades with spanwise variable elastic axis offset: Classic issues revisited and new formulations

In response to a systematic methodology assessment program directed to the aeroelastic stability of hingeless helicopter rotor blades, improved basic aeroelastic reformulations and new formulations relating to structural sweep were achieved. Correlational results are presented showing the substantially improved performance of the G400 aeroelastic analysis incorporating these new formulations. The formulations pertain partly to sundry solutions to classic problem areas, relating to dynamic inflow with vortex-ring state operation and basic blade kinematics, but mostly to improved physical modeling of elastic axis offset (structural sweep) in the presence of nonlinear structural twist. Specific issues addressed are an alternate modeling of the delta EI torsional excitation due to compound bending using a force integration approach, and the detailed kinematic representation of an elastically deflected point mass of a beam with both structural sweep and nonlinear twist.

Bielawa, Richard L.↗
NASA NTRS1988

Parametric studies of advanced turboprops

The effects of geometric variables (sweep and twist) on the structural performance of advanced turboprops are investigated. The investigation is limited to aerodynamically efficient turboprops using an acceptable design configuration as a baseline. The baseline configuration is modified using a seven by seven array of independently varying sweep and twist parameters while maintaining acceptable aerodynamic efficiency. The turboprop structural performance is evaluated in terms of critical speeds, tip displacements, and vibration frequencies where geometric nonlinearities are included. The results obtained are presented in such a manner as to highlight the effects of sweep and twist on the structural performance of aerodynamically efficient turboprop configurations.

Fertis, D. G.↗
NASA NTRS1988

Parametric studies of advanced turboprops

The effects of geometric variables (sweep and twist) on the structural performance of advanced turboprops are investigated. The investigation is limited to aerodynamically efficient turboprops using an acceptable design configuration as a baseline. The baseline configuration is modified using a seven by seven array of independently varying sweep and twist parameters while maintaining acceptable aerodynamic efficiency. The turboprop structural performance is evaluated in terms of critical speeds, tip displacements, and vibration frequencies where geometric nonlinearities are included. The results obtained are presented in such a manner as to highlight the effects of sweep and twist on the structural performance of aerodynamically efficient turboprop configurations.

Maser, J. G.↗
NASA NTRS1987

F-14 VSTFE and results of the cleanup flight test program

Flight transition data applicable to swept wings at high subsonic speeds are needed to make valid assessments of the potential for natural laminar flow or laminar flow control for transports of various sizes at various cruise speeds. NASA initiated the variable sweep transition flight experiment (VSTFE) to help establish a boundary layer transition data base for use in laminar flow wing design. The carrier vehicle for this experiment is an F-14, which has variable sweep capability. The variable sweep outer panels of the F-14 were modified with natural laminar flow gloves to provide not only smooth surfaces but also airfoils that can produce a wide range of pressure distributions for which transition location can be determined. The VSTFE program is briefly described and some preliminary glove I flight results are presented.

Meyer, Robert R.↗
NASA NTRS1990

An aerodynamic tradeoff study of the scissor wing configuration

A scissor wing configuration, consisting of two independently sweeping wings was numerically studied. This configuration was also compared with an equivalent fixed wing baseline. Aerodynamic and stability and control characteristics of these geometries were investigated over a wide range of flight Mach numbers. It is demonstrated that in the purely subsonic flight regime, the scissor wing can achieve higher aerodynamic efficiency as the result of slightly higher aspect ratio. In the transonic regime, the lift to drag ratio of the scissor wing is shown to be higher than that of the baseline, for higer values of the lift coefficient. This tends to make the scissor wing more efficient during transonic cruise at high altitudes as well as during air combat at all altitudes. In supersonic flight, where the wings are maintained at maximum sweep angle, the scissor wing is shown to have a decided advantage in terms of reduced wave drag. From the view point of stability and control, the scissor wing is shown to have distinct advantages. It is shown that this geometry can maintain a constant static margin in supersonic as well as subsonic flight, by proper sweep scheduling. Furthermore, it is demonstrated that addition of wing mounted elevons can greatly enhance control authority in pitch and roll.

Selberg, Bruce P.↗
NASA NTRS1990

Mach 6 testing of two generic three-dimensional sidewall compression scramjet inlets in tetrafluoromethane

Three-dimensional sidewall compression scramjet inlets with leading edge sweeps of 30 and 70 degrees have been tested in the Langley Hypersonic CF4 Tunnel at Mach 6 and a ratio of specific heats of 1.2. The effects of cowl position, contraction ratio, and Reynolds number were investigated. The models were instrumented with 42 static pressure orifices distributed on the sidewalls, baseplate, and cowl. Schlieren movies were made of each test for flow visualization of the entrance plane and cowl region. In order to obtain an approximate characterization of the flow field, a modification to two-dimensional inviscid oblique shock theory was derived to accommodate the three-dimensional effects of leading edge sweep. This theory qualitatively predicted the reflected shock structure/sidewall impingement locations and the observed increase in spillage (flow upturning) with increasing leading edge sweep. The primary effect of moving the cowl forward is capturing the flow which would have otherwise spilled out ahead of the cowl. Increasing the contraction ratio (moving the sidewalls closer together) increases the number of internal shock reflections and hence incrementally increases the sidewall pressure distribution. Significant Reynolds number effects were noted over a small range of Reynolds number.

Holland, Scott D.↗
NASA NTRS1990

A computational parametric study of three-dimensional sidewall compression scramjet inlets at Mach 10

A computational parametric study of three-dimensional sidewall compression scramjet inlets has been performed. The parameters considered for the study include the leading edge sweep angle, varied between 30 and 60 degrees, and the cowl position, located at the throat and at two forward positions. Additionally, the effects of laminar and turbulent boundary layers as well as adiabatic and cold wall boundary conditions are assessed. The parametric study is performed for a Mach number of 10 and a unit freestream Reynolds number of 2 x 10 to the 6th/ft at a geometric contraction ratio of 5. Comparisons among the various configurations are made in terms of the gross parameters of mass capture, throat Mach number, total pressure recovery, and area weighted internal pressure ratios, as well as more detailed flow field phenomena comparisons. The inclusion of one 0-deg sweep computation indicates that the leading edge may be swept by up to 30 deg before significant changes in the gross flow field parameters occur. It is found that a 45-deg sweep configuration provides a good compromise of mass capture, total pressure recovery, and internal compression.

Holland, Scott D.↗
NASA NTRS1989

Some aerodynamic characteristics of the scissor wing configuration

A scissor wing configuration, consisting of four adjustable wing surfaces, is compared with a comparable fixed wing baseline configuration. Wave drag, induced drag, viscous drag, thrust required, and gust loading are calculated for both configurations. The scissor wing is shown to have lower zero lift wave drag and higher total lift to drag ratios than the baseline. It is demonstrated that the scissor configurations' sweep can be programmed to keep the static margin fixed. Thrust required for both the fixed static margin case and a constant sweep angle case are presented with the scissor configuration requiring lower thrust levels. The gust loading ratio of the scissor wing to the baseline is also shown to be significantly less than 1.0 for sweep angles greater than 20 degrees.

Selberg, Bruce P.↗
NASA NTRS1990

A numerical method for relating two- and three-dimensional pressure distributions on transonic wings

This paper presents a preliminary design method for determining a wing's design pressure distribution and geometry based on airfoil normal Mach numbers and airfoil loading. In this method, the perturbation velocities in supercritical regions are computed from airfoil transonic normal Mach numbers and include the influence of local sweep, taper, and three-dimensional induced velocities, so that the appearance and strength of shocks can be expected to resemble those of the airfoil. The velocities in subcritical wing regions are scaled first with simple sweep theory, and then to achieve the desired load distribution. The method was applied to the design of an oblique flying wing, using a linear potential method. The required wing area could be reduced by 14 percent using this method rather than simple sweep theory.

Kroo, Ilan↗
NASA NTRS1992

Prediction of ice accretion on a swept NACA 0012 airfoil and comparisons to flight test results

In the winter of 1989-90, an icing research flight project was conducted to obtain swept wing ice accretion data. Utilizing the NASA Lewis Research Center's DHC-6 DeHavilland Twin Otter aircraft, research flights were made into known icing conditions in Northeastern Ohio. The icing cloud environment and aircraft flight data were measured and recorded by an onboard data acquisition system. Upon entry into the icing environment, a 24 inch span, 15 inch chord NACA 0012 airfoil was extended from the aircraft and set to the desired sweep angle. After the growth of a well defined ice shape, the airfoil was retracted into the aircraft cabin for ice shape documentation. The ice accretions were recorded by ice tracings and photographs. Ice accretions were mostly of the glaze type and exhibited scalloping. The ice was accreted at sweep angles of 0, 30, and 45 degrees. A 3-D ice accretion prediction code was used to predict ice profiles for five selected flight test runs, which include sweep angle of zero, 30, and 45 degrees. The code's roughness input parameter was adjusted for best agreement. A simple procedure was added to the code to account for 3-D ice scalloping effects. The predicted ice profiles are compared to their respective flight test counterparts. This is the first attempt to predict ice profiles on swept wings with significant scalloped ice formations.

Reehorst, Andrew L.↗
NASA NTRS1992

Implicit upwind-Euler solution algorithms for unstructured-grid applications

The development of implicit upwind algorithms for the solution of the three-dimensional, time-dependent Euler equations on unstructured tetrahedral meshes is described. The implicit temporal discretization involves either a two-sweep Gauss-Seide relaxation procedure, a two-sweep Point-Jacobi relaxation procedure, or a single-sweep Point-Implicit procedure; the upwind spatial discretization is based on the flux-difference splitting of Roe. Detailed descriptions of the three implicit solution algorithms are given, and calculations for the Boeing 747 transport configuration are presented to demonstrate the algorithms. Advantages and disadvantages of the implicit algorithms are discussed. A steady-state solution for the 747 configuration, obtained at transonic flow conditions using a mesh of over 100,000 cells, required less than one hour of CPU time on a Cray-2 computer, thus demonstrating the speed and robustness of the general capability.

Batina, John T.↗
NASA NTRS1992

Prediction of ice accretion on a swept NACA 0012 airfoil and comparisons to flight test results

In the winter of 1989-90, an icing research flight project was conducted to obtain swept wing ice accretion data. Utilizing the NASA Lewis Research Center's DHC-6 DeHavilland Twin Otter aircraft, research flights were made into known icing conditions in Northeastern Ohio. The icing cloud environment and aircraft flight data were measured and recorded by an onboard data acquisition system. Upon entry into the icing environment, a 24 inch span, 15 inch chord NACA 0012 airfoil was extended from the aircraft and set to the desired sweep angle. After the growth of a well defined ice shape, the airfoil was retracted into the aircraft cabin for ice shape documentation. The ice accretions were recorded by ice tracings and photographs. Ice accretions were mostly of the glaze type and exhibited scalloping. The ice was accreted at sweep angles of 0, 30, and 45 degrees. A 3-D ice accretion prediction code was used to predict ice profiles for five selected flight test runs, which include sweep angle of zero, 30, and 45 degrees. The code's roughness input parameter was adjusted for best agreement. A simple procedure was added to the code to account for 3-D ice scalloping effects. The predicted ice profiles are compared to their respective flight test counterparts. This is the first attempt to predict ice profiles on swept wings with significant scalloped ice formations.

Reehorst, Andrew L.↗
NASA NTRS1992

A new aeroelastic model for composite rotor blades with straight and swept tips

An analytical model for predicting the aeroelastic behavior of composite rotor blades with straight and swept tips is presented. The blade is modeled by beam type finite elements along the elastic axis. A single finite element is used to model the swept tip. The nonlinear equations of motion for the finite element model are derived using Hamilton's principle and based on a moderate deflection theory and accounts for: arbitrary cross-sectional shape, pretwist, generally anisotropic material behavior, transverse shears and out-of-plane warping. Numerical results illustrating the effects of tip sweep, anhedral and composite ply orientation on blade aeroelastic behavior are presented. Tip sweep can induce aeroelastic instability by flap-twist coupling. Tip anhedral causes lag-torsion and flap-axial couplings, however, its effects on blade stability is less pronounced than the effect due to sweep. Composite ply orientation has a substantial effect on blade stability.

Yuan, Kuo-An↗
NASA NTRS1991

Sufficient conditions for a local minimum of the Bolza problem with multiple terminal point constraints

Sufficient conditions for a weak relative minimum are derived for a form of the Bolza problem of variational calculus. The derivation ties together first-order and second-order conditions in a unified consistent manner, addresses controllability considerations in some detail, and clarifies some small inconsistencies in earlier work. The resulting second-order conditions of optimality involve the integration of fewer backward-sweep matrix elements than the standard conditions in the literature for problems with an unspecified final time. As a result, the backward-sweep matrices have the same general structure and dimensionality whether the final time is specified or free, with the terminal values of two of three sweep matrices being more complicated in the latter case.

Wood, Lincoln J.↗
NASA NTRS1992

Comparison of current Shuttle and pre-Challenger flight suit reach capability during launch accelerations

The Challenger accident prompted the creation of a crew escape system which replaced the former Launch Entry Helmet (LEH) ensemble with the current Launch Entry Suit (LES). However, questions were raised regarding the impact of this change on crew reach capability. This study addressed the question of reach capability and its effects on realistic ground-based training for Space Shuttle missions. Eleven subjects performed reach sweeps in both the LEH and LES suits during 1 and 3 Gx acceleration trials in the Brooks AFB centrifuge. These reach sweeps were recorded on videotape and subsequently analyzed using a 3D motion analysis system. The ANOVA procedure of the Statistical Analysis System program was used to evaluate differences in forward and overhead reach. The results showed that the LES provided less reach capability than its predecessor, the LEH. This study also demonstrated that, since there was no substantial difference between 1 and 3 Gx reach sweeps in the LES, realistic Shuttle launch training may be accomplished in ground based simulators.

Bagian, James P.↗