Search NASA⌕ Search

SEARCH · Search NASA

Results for “Saturation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Group-type hydrocarbon standards for high-performance liquid chromatographic analysis of middistillate fuels

A new high-performance liquid chromatographic (HPLC) method for group-type analysis of middistillate fuels is described. It uses a refractive index detector and standards that are prepared by reacting a portion of the fuel sample with sulfuric acid. A complete analysis of a middistillate fuel for saturates and aromatics (including the preparation of the standard) requires about 15 min if standards for several fuels are prepared simultaneously. From model fuel studies, the method was found to be accurate to within 0.4 vol% saturates or aromatics, and provides a precision of + or - 0.4 vol%. Olefin determinations require an additional 15 min of analysis time. However, this determination is needed only for those fuels displaying a significant olefin response at 200 nm (obtained routinely during the saturated/aromatics analysis procedure). The olefin determination uses the responses of the olefins and the corresponding saturates, as well as the average value of their refractive index sensitivity ratios (1.1). Studied indicated that, although the relative error in the olefins result could reach 10 percent by using this average sensitivity ratio, it was 5 percent for the fuels used in this study. Olefin concentrations as low as 0.1 vol% have been determined using this method.

Otterson, D. A.↗
NASA NTRS1985

Humidity effects on adhesion of nickel-zinc ferrite in elastic contact with magnetic tape and itself

The effects of humidity on the adhesion of Ni-Zn ferrite and magnetic tape in elastic contact with a Ni-Zn ferrite hemispherical pin in moist nitrogen were studied. Adhesion was independent of normal load in dry, humid, and saturated nitrogen. Ferrites adhere to ferrites in a saturated atmosphere primarily from the surface tension effects of a thin film of water adsorbed on the ferrite surfaces. The surface tension of the water film calculated from the adhesion results was 48 times 0.00001 to 56 times 0.00001 N/cm; the accepted value for water is 72.7 x 0.00001 N/cm. The adhesion of ferrite-ferrite contacts increased gradually with increases in relative humidity to 80 percent, but rose rapidly above 80 percent. The adhesion at saturation was 30 times or more greater than that below 80 percent relative humidity. Although the adhesion of magnetic tape - ferrite contacts remained low below 40 percent relative humidity and the effect of humidity was small, the adhesion increased considerably with increasing relative humidity above 40 percent. The changes in adhesion of elastic contacts were reversible on humidifying and dehumidifying.

Miyoshi, K.↗
NASA NTRS1984

Excerpts from the paper: Research Status and Recommendation from the Alaska Workshop on Gravity Waves and Turbulence in the Middle Atmosphere, part 1.3A

Internal gravity waves are disturbances whose intrinsic frequencies k(c - u) are smaller than the Brunt-Vaisala frequency (N). Their importance arises because: they are the major components of the total flow and temperature variability fields of the mesosphere (i.e., shears and lapse rates) and hence constitute the likely sources of turbulence; and they are associated with fluxes of momentum that communicate stresses over large distances. For example, gravity waves exert a drag on the flow in the upper mesosphere. However, in order for gravity waves to exert a net drag on the atmosphere, they must be attenuated. There are two general types of processes that seek to attenuate gravity waves: dissipation and saturation. Dissipation is any process that is effective independent of the wave amplitude, while saturation occurs when certain wave amplitude conditions are met. Radiative damping is an example of dissipation, while convective overturning is an example of saturation. The two processes are not mutually exclusive.

Fritts, D. C.↗
NASA NTRS1983

A 20 GHz, 75 watt, helix TWT for space communications

A space-qualified, helix-type traveling wave tube is being developed for satellite communication systems in the frequency band of 17.7 to 21.2 GHz. The design approach stresses very high efficiency operation, but with very low distortion. The tube provides multi-mode operation, permitting CW saturated power output levels of 75, 40, and 7.5 W. Operation is also anticipated at 5 dB below these saturation levels to achieve the required low distortion levels. Advanced construction features include a five-stage depressed collector, a diamond supported helix slow-wave circuit, and a type M dispenser cathode. High reliability and long life (10 yr) are objectives of the tube design. Preliminary test results on early developmental models of this tube are very encouraging. An output power of 75 to 90 W has been achieved over the full bandwidth with about 40 dB of saturated gain. More importantly, the basic electronic efficiency of the interaction process has been increased from about 7.5-11 percent by the use of the diamond helix support compared to earlier tubes using BeO support rods. This effort is supported by NASA Lewis Research Center and is aimed toward application in the NASA Advanced Communications Satellite Technology Program.

Heney, J. F.↗
NASA NTRS1985

The zero-frequency ion ring instability

The electrostatic zero-frequency ion ring instability with wave vector perpendicular to a uniform magnetic field B is examined through linear and second-order theory as well as by computer simulation. In the simulation ions are taken as magnetized particles; the electrons are described as a massless fluid subject to E x B motion. Saturation of the instability is primarily due to broadening of the ion ring distribution. A second-order theory provides an approximate criterion for the saturation amplitude, as does a simple trapping argument. Thus, for the simulation presented here, both quasi-linear and trapping effects contribute to saturation.

Gary, S. P.↗
NASA NTRS1985

Explosive tail reconnection - The growth and expansion phases of magnetospheric substorms

In the current 'conceptual' model of magnetospheric substorms, the growth phase terminates and the expansion phase commences with the onset of rapid reconnection at a new, near-earth X-type neutral line. Physical concepts developed in the analysis of the collisionless tearing mode and the flow of collisionless plasma in weakly magnetized, thin current sheets are combined to construct a model of purely collisionless, time-dependent, ion-dominated reconnection. Formulated in the context of time-dependent magnetospheric convection, the model describes the reconnection collapse of the initially thick plasma sheet. In the nonlinear phase the reconnection rate grows explosively in time and saturates into a steady collisionless reconnection flow when the initial magnetic flux in the current sheet has reconnected; at saturation the reconnection rate is comparable to the maximum Petschek rate. The time scale and dynamics of the explosive reconnection model are broadly consistent with observations of substorm growth phase and expansion phase onset. For typical plasma sheet parameters the explosive reconnection electromotive force across the tail approaches 1 MV at saturation.

Coroniti, F. V.↗
NASA NTRS1985

The integrated enstrophy budget of the winter stratosphere diagnosed from LIMS data

The quasi-geostrophic integrated enstrophy budget for the 1978 to 1979 winter has been analyzed from 10-0.1 mb using LIMS data. During January and late February periods a significant imbalance in the budget appears at 10mb. This imbalance is attributed to Rossby wave breaking. It is produced by the irreversible transfer of enstrophy to smaller scales not resolved by LIMS. The imbalance episodes correspond well to the appearance of Ertel vorticity filaments shown by McIntyre and Palmer (1984). From a seasonal viewpoint, the integrated enstrophy shows an average (although irregular) transfer from a zonal mean reservoir to waves which are then dissipated. On a shorter time scale the integrated enstrophy sloshes back and forth between the waves and mean flow in early winter; then, beginning with the January sudden warming, the total enstrophy is reduced more rapidly. Between 10 mb and 1 mb this reduction is more or less continuous until the end of February. However, in the mesosphere the total enstrophy decrease is very short lived, being quickly restored after the January warming. Even though the zonal mean integrated enstrophy is large, only about 10% can be utilized by the waves. The available integrated potential enstrophy is introduced, which is a better measure of how close the flow is to saturation by Rossby waves. The largest amount of available potential enstrophy in early January is at 1 mb with decreasing amounts above and below. Saturation of the flow by Rossby waves occurs below 1 mb only coincident with sudden warmings; however, at mesospheric heights the flow appears to be nearly saturated throughout the winter.

Schoeberl, M. R.↗
NASA NTRS1986

Bearing tester data compilation analysis, and reporting and bearing math modeling

Integration of heat transfer coefficients, modified to account for local vapor quality, into the 45 mm bearing model has been completed. The model has been evaluated with two flow rates and subcooled and saturated coolant. The evaluation showed that by increasing the flow from 3.6 to 7.0 lbs/sec the average ball temperature was decreased by 102 F, using a coolant temperature of -230 F. The average ball temperature was decreased by 63 F by decreasing the inlet coolant temperature from saturated to -230 F at a flow rate of 7.0 lbs/sec. Since other factors such as friction, cage heating, etc., affect bearing temperatures, the above bearing temperature effects should be considered as trends and not absolute values. The two phase heat transfer modification has been installed in the 57 mm bearing model and the effects on bearing temperatures have been evaluated. The average ball temperature was decreased by 60 F by increasing the flow rate from 4.6 to 9.0 lbs/sec for the subcooled case. By decreasing the inlet coolant temperature from saturation to -24 F, the average ball temperature was decreased 57 F for a flow rate of 9.0 lbs/sec. The technique of relating the two phase heat transfer coefficient to local vapor quality will be applied to the tester model and compared with test data.

Cody, J. C.↗
NASA NTRS1986

Modeling of zero gravity venting: Studies of two-phase heat transfer under reduced gravity

The objective is to predict the pressure response of a saturated liquid-vapor system when undergoing a venting or depressurization process in zero gravity at low vent rates. An experimental investigation of the venting of cylindrical containers partially filled with initially saturated liquids was previously conducted under zero-gravity conditions and compared with an analytical model which incorporated the effect of interfacial mass transfer on the ullage pressure response during venting. A new model is presented to improve the estimation of the interfacial mass transfer. Duhammel's superposition integral is incorporated to approximate the transient temperature response of the interface, treating the liquid as a semi-infinite solid with conduction heat transfer. Account is also taken of the condensation taking place within the bulk of a saturated vapor as isentropic expansion takes place. Computational results are presented for the venting of R-11 from a given vessel and initial state for five different venting rates over a period of three seconds, and compared to prior NASA experiments. An improvement in the prediction of the final pressure takes place, but is still considerably below the measurements.

Merte, H., Jr.↗
NASA NTRS1987

Nonlinear absorption in AlGaAs/GaAs multiple quantum well structures grown by metalorganic chemical vapor deposition

This paper reports the study of growth conditions for achieving the sharp exciton resonances and low-intensity saturation of these resonances in AlGaAs-GaAs multiple quantum well structures grown by metalorganic chemical vapor deposition. Low growth temperature is necessary to observe this sharp resonance feature at room temperature. The optimal growth conditions are a tradeoff between the high temperatures required for high quality AlGaAs and low temperatures required for high-purity GaAs. A strong optical saturation of the excitonic absorption has been observed. A saturation density as low as 250 W/sq cm is reported.

Lee, H. C.↗
NASA NTRS1988

Development of a torsion balance for adhesion measurements

A new torsion balance for study of adhesion in ceramics is discussed. A torsion wire and a linear variable differential transformer are used to monitor load and to measure pull-off force (adhesion force). The investigation suggests that this torsion balance is valuable in studying the interfacial properties of ceramics in controlled environments such as in ultrahigh vacuum. The pull-off forces measured in dry, moist, and saturated nitrogen atmosphere demonstrate that the adhesion of silicon nitride contacts remains low at humidities below 80 percent but rises rapidly above that. The adhesion at saturation is 10 times or more greater than that below 80 percent relative humidity. The adhesion in a saturated atmosphere arises primarily from the surface tension effects of a thin film of water adsorbed on the surface. The surface tension of the water film was 58 x 10 to the minus 5 to 65 x 10 to the minus 5 power. The accepted value for water is 72.7 x 10 to the minus 5 power N/cm. Adhesion characteristics of silicon nitride in contact with metals, like the friction characteristics of silicon carbide to metal contacts, can be related to the relative chemical activity of metals in ultrahigh vacuum. The more active the metal, the higher the adhesion.

Miyoshi, Kazuhisa↗
NASA NTRS1988

The electromagnetic ion cyclotron instability in the Io torus

The electromagnetic ion cyclotron waves which are expected to exist in the Jovian magnetosphere are investigated. The temperature anisotropy generated by the inward radial diffusion of hot ions gives rise to an instability of L mode waves in the off-equatorial region of the Io torus. The resulting pitch angle scattering has been suggested as the cause for the precipitation of ions into the loss cone and auroral excitation. The linear wave dispersion is first examined, and the nonlinear wave amplitude for the saturated state is studied. Two estimates of the wave saturation level are checked by performing an electromagnetic hybrid simulation. Estimated nonlinear saturation amplitudes are compared with those resulting from linear amplification in a finite length. The result shows that the waves in the Jovian magnetosphere produced by the hot protons are mostly in a linear regime.

Machida, S.↗
NASA NTRS1988

Photochemical trajectory modelling studies of the 1987 Antarctic spring vortex

Simulations of Antarctic ozone photochemistry performed using a photochemical model integrated along air parcel trajectories are described. This type of model has a major advantage at high latitudes of being able to simulate correctly the complex interaction between photolysis and temperature fields, which, because of the polar night cannot be represented accurately in a zonally averaged framework. Isentropic air parcel trajectories were computed using Meteorological Office global model analyses and forecast fields from positions along the ER-2 flight paths during the Airborne Antarctic Ozone Experiment in Austral Spring 1987. A photochemical model is integrated along these trajectories using the aircraft observations to initialize constituent concentrations. The model includes additional reactions of the ClO dimer and also bromine reactions, which are thought to play a significant role in Antarctica. The model also includes heterogeneous reactions which are invoked when the air parcel passes through a polar stratospheric cloud (PSC). The existence of a PSC is determined throughout the course of the model integration from the parcel temperature and the saturated vapour pressure of water over an assumed H2O/HNO3 mixture. The air parcel temperature is used to determine the saturated vapor pressure of HNO3 over the same mixture. Mixing ratios which exceed saturation result in condensation of the excess in the model and hence lead to a reduction of the amount of gas phase NO2 available for chemical reaction.

Austin, J.↗
NASA NTRS1989

Nonlinear interactions in mixing layers and compressible heated round jets

The nonlinear interactions between a fundamental instability mode and both its harmonics and the changing mean flow are studied using the weakly nonlinear stability theory of Stuart and Watson, and numerical solutions of coupled nonlinear partial differential equations. The first part focuses on incompressible cold (or isothermal; constant temperature throughout) mixing layers, and for these, the first and second Landau constants are calculated as functions of wavenumber and Reynolds number. It is found that the dominant contribution to the Landau constants arises from the mean flow changes and not from the higher harmonics. In order to establish the range of validity of the weakly nonlinear theory, the weakly nonlinear and numerical solutions are compared and the limitation of each is discussed. At small amplitudes and at low-to-moderate Reynolds numbers, the two results compare well in describing the saturation of the fundamental, the distortion of the mean flow, and the initial stages of vorticity roll-up. At larger amplitudes, the interaction between the fundamental, second harmonic, and the mean flow is strongly nonlinear and the numerical solution predicts flow oscillations, whereas the weakly nonlinear theory yields saturation. In the second part, the weakly nonlinear theory is extended to heated (or nonisothermal; mean temperature distribution) subsonic round jets where quadratic and cubic nonlinear interactions are present, and the Landau constants also depend on jet temperature ratio, Mach number and azimuthal mode number. Under exponential growth and nonlinear saturation, it is found that heating and compressibility suppress the growth of instability waves, that the first azimuthal mode is the dominant instability mode, and that the weakly nonlinear solution describes the early stages of the roll-up of an axisymmetric shear layer. The receptivity of a typical jet flow to pulse type input disturbance is also studied by solving the initial value problem and then examining the behavior of the long-time solution.

Jarrah, Yousef Mohd↗
NASA NTRS1991

Investigation of long term stability in metal hydrides

It is apparent from the literature and the results of this study that cyclic degradation of AB(5) type metal hydrides varies widely according to the details of how the specimens are cycled. The Rapid Cycle Apparatus (RCA) used produced less degradation in 5000 to 10000 cycles than earlier work with a Slow Cycle Apparatus (SCA) produced in 1500 cycles. Evidence is presented that the 453 K (356 F) Thermal Aging (TA) time spent in the saturated condition causes hydride degradation. But increasing the cooling (saturation) period in the RCA did not greatly increase the rate of degradation. It appears that TA type degradation is secondary at low temperatures to another degradation mechanism. If rapid cycles are less damaging than slow cycles when the saturation time is equal, the rate of hydriding/dehydriding may be an important factor. The peak temperatures in the RCA were about 30 C lower than the SCA. The difference in peak cycle temperatures (125 C in the SCA, 95 C in RCA) cannot explain the differences in degradation. TA type degradation is similar to cyclic degradation in that nickel peaks and line broadening are observed in X ray diffraction patterns after either form of degradation.

Marmaro, Roger W.↗
NASA NTRS1991

Fatigue damage accumulation in nickel prior to crack initiation

The accumulation of lattice defects during fatigue cycling of nickel was investigated by electrical resistivity measurements, positron annihilation lifetime spectroscopy and transmission electron microscopy. Dislocations and vacancy clusters were found to be the main defect types. During cycling of axial and flexural samples at constant load amplitude, the dislocations form a saturated structure early in the fatigue life. This saturated structure consists of a cellular dislocation matrix, in which persistent slip bands (PSBs) begin to operate after the saturation has been established. Vacancies and vacancy clusters are formed during fatigue as a consequence of repetitive dislocation glide in the PSB structure. When PSBs operate, the matrix is assumed to be dormant, allowing vacancies to accumulate preferentially in the PSBs. The increase in vacancy concentration then accounts for the monotonic accumulation of fatigue damage, which points to the importance of vacancy accumulation as a precursor to crack nucleation.

Grobstein, T. L.↗
NASA NTRS1992

Analysis of cyclotron harmonic emissions at the outer planets

The flyby missions of Voyagers 1 and 2 at Jupiter, Saturn and Uranus revealed intense waves above the electron gyrofrequency. Observation of waves at the upper hybrid frequency is often accompanied by power at adjacent electron Bernstein harmonics, and the relative power in these modes depends both on the density and temperature ratios of the cold background electron population and the hot magnetospheric electrons which drive the instability. A model of electron distributions which is consistent with observations is used for analysis of the excited waves, their dependence upon plasma parameters, and the time scales of the saturation processes. It is shown that in the presence of two-temperature electron distributions the linear excitation is due to a fluidlike coupling of two eigenmodes for perpendicular propagation and to kinetic destalization of oblique modes. The dependence of linear growth rates on propagation angle is presented, along with results from particle simulations. A quasi-linear diffusion time for relaxing the hot electron loss cone is calculated and compared with simulation results. This time scale is faster than for local saturation by heating the cold population, and also the convective amplification time scale, suggesting that the waves saturate at quasi-linear levels, while being convectively localized to the equatorial regions of the outer planetary magnetospheres.

Roth, I.↗
NASA NTRS1993

Lower hybrid turbulence at cometary bow wave and acceleration of cometary protons

The wave measurements at the spacecraft encounters with Comet Halley have shown intense wave activity at the lower hybrid frequency. The excitation of the lower hybrid instability by the pickup cometary ions (protons and water group) in the bow wave region and the quasi-linear diffusion of the ions in these fluctuations are discussed. The quasi-linear diffusion of the pickup protons takes place over a scale length shorter than that of the heavier water group ions. This enhances damping of the waves by protons, and when the pickup proton density is large enough, it can result in the saturation of the instability as this damping balances the heavy ion driven growth. The observed electric field amplitude and the scale length of proton relaxation are in agreement with the theory. For small pickup proton density the instability can saturate due to the wave energy cascade arising from the modulation instability of the large-amplitude lower hybrid waves. This saturation mechanism leads to electron acceleration and suprathermal tail formation.

Shapiro, V. D.↗