Search NASA⌕ Search

SEARCH · Search NASA

Results for “Simplified Simulator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

A Generic Inner-Loop Control Law Structure for Six-Degree-of-Freedom Conceptual Aircraft Design

A generic control system framework for both real-time and batch six-degree-of-freedom (6-DOF) simulations is presented. This framework uses a simplified dynamic inversion technique to allow for stabilization and control of any type of aircraft at the pilot interface level. The simulation, designed primarily for the real-time simulation environment, also can be run in a batch mode through a simple guidance interface. Direct vehicle-state acceleration feedback is required with the simplified dynamic inversion technique. The estimation of surface effectiveness within real-time simulation timing constraints also is required. The generic framework provides easily modifiable control variables, allowing flexibility in the variables that the pilot commands. A direct control allocation scheme is used to command aircraft effectors. Primary uses for this system include conceptual and preliminary design of aircraft, when vehicle models are rapidly changing and knowledge of vehicle 6-DOF performance is required. A simulated airbreathing hypersonic vehicle and simulated high-performance fighter aircraft are used to demonstrate the flexibility and utility of the control system.

Cox, Timothy H.↗

A Generic Inner-Loop Control Law Structure for Six-Degree-of-Freedom Conceptual Aircraft Design

A generic control system framework for both real-time and batch six-degree-of-freedom simulations is presented. This framework uses a simplified dynamic inversion technique to allow for stabilization and control of any type of aircraft at the pilot interface level. The simulation, designed primarily for the real-time simulation environment, also can be run in a batch mode through a simple guidance interface. Direct vehicle-state acceleration feedback is required with the simplified dynamic inversion technique. The estimation of surface effectiveness within real-time simulation timing constraints also is required. The generic framework provides easily modifiable control variables, allowing flexibility in the variables that the pilot commands. A direct control allocation scheme is used to command aircraft effectors. Primary uses for this system include conceptual and preliminary design of aircraft, when vehicle models are rapidly changing and knowledge of vehicle six-degree-of-freedom performance is required. A simulated airbreathing hypersonic vehicle and simulated high-performance fighter aircraft are used to demonstrate the flexibility and utility of the control system.

Cox, Timothy H.↗

Discrete element simulation of Pebble Bed Reactors on graphics processing units

Prediction of pebble positions in a Pebble Bed Reactor (PBR) is necessary for both reactor physics and thermal hydraulics simulations as the arrangement of pebbles has a significant impact on the resulting core power, coolant flow, and fuel temperature. Knowledge of pebble movement as the fuel is cycled through the core is also critical for predicting the fuel residence time and subsequently, the fuel burnup. Simulation with the Discrete Element Method (DEM) can provide knowledge of both the fuel packing and the fuel movement during cycling. Previous works that have performed 3D full-core DEM simulation of PBRs have used simplified models that neglect reflector wall features. This work employs a graphics processing unit (GPU)-enabled DEM code, Project Chrono, to analyze the differences in pebble packing and pebble velocities between a simplified smooth PBR reflector and a more realistic reflector that includes circular wall features. Additionally, a sensitivity study is performed on the depth of the wall features to ensure that crystallization is prevented. Project Chrono is also validated for PBR cycling applications using experimental data. It is found that wall features with a depth of at least 0.5 pebble diameters significantly reduce crystallization in the near-wall region, leading to discrepancies in both packing fraction and pebble velocity in this region compared to the simplified reflector models. These discrepancies are found to lead to roughly a 5–10% difference in the prediction of the near-wall porosity and a 10% difference in the prediction of the velocity of pebbles near the wall. As a result of these discrepancies, it is suggested that future DEM simulations of PBRs include wall features to reduce modeling errors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA/ESA CV-990 spacelab simulation

Due to interest in the application of simplified techniques used to conduct airborne science missions at NASA's Ames Research Center, a joint NASA/ESA endeavor was established to conduct an extensive Spacelab simulation using the NASA CV-990 airborne laboratory. The scientific payload was selected to perform studies in upper atmospheric physics and infrared astronomy with principal investigators from France, the Netherlands, England, and several groups from the United States. Communication links between the 'Spacelab' and a ground based mission operations center were limited consistent with Spacelab plans. The mission was successful and provided extensive data relevant to Spacelab objectives on overall management of a complex international payload; experiment preparation, testing, and integration; training for proxy operation in space; data handling; multiexperimenter use of common experimenter facilities (telescopes); multiexperiment operation by experiment operators; selection criteria for Spacelab experiment operators; and schedule requirements to prepare for such a Spacelab mission.

Source record↗

Verification of diesel spray ignition phenomenon in dual-fuel diesel-piloted premixed natural gas engine

Dual-fuel (DF) engines, in which premixed natural gas and air in an open-type combustion chamber is ignited by diesel-fuel pilot sprays, have been more popular for marine use than pre-chamber spark ignition (PCSI) engines because of their superior durability. However, control of ignition and combustion in DF engines is more difficult than in PCSI engines. In this context, here we focus on the ignition stability of n-heptane pilot-fuel jets injected into a compressed premixed charge of natural gas and air at low-load conditions. To aid understanding of the experimental data, chemical-kinetics simulations were carried out in a simplified engine-environment that provided insight into the chemical effects of methane (CH4) on pilot-fuel ignition. The simulations reveal that CH4 has an effect on both stages of n-heptane autoignition: the small, first-stage, cool-flame-type, low-temperature ignition (LTI) and the larger, second-stage, high-temperature ignition (HTI). As the ratio of pilot-fuel to CH4 entrained into the spray decreases, the initial oxidization of CH4 consumes the OH radicals produced by pilot-fuel decomposition during LTI, thereby inhibiting its progression to HTI. Using imaging diagnostics, the spatial and temporal progression of LTI and HTI in DF combustion are measured in a heavy-duty optical engine, and the imaging data are analyzed to understand the cause of severe fluctuations in ignition timing and combustion completeness at low-load conditions. Images of cool-flame and hydroxyl radical (OH*) chemiluminescence serve as indicators of LTI and HTI, respectively. The cycle-to-cycle and spatial variation in ignition extracted from the imaging data are used as key metrics of comparison. The imaging data indicate that the local concentration of the pilot-fuel and the richness of the surrounding natural-gas air mixture are important for LTI and HTI, but in different ways. In particular, higher injection pressures and shorter injection durations increase the mixing rate, leading to lower concentrations of pilot-fuel more quickly, which can inhibit HTI even as LTI remains relatively robust. Decreasing the injection pressure from 80 MPa to 40 MPa and increasing the injection duration from 500 µs to 760 µs maintained constant pilot-fuel mass, while promoting robust transition from LTI to HTI by effectively slowing the mixing rate. This allows enough residence time for the OH radicals, produced by the two-stage ignition chemistry of the pilot-fuel, to accelerate the transition from LTI to HTI before being consumed by CH4 oxidation. Thus from a practical perspective, for a premixed natural gas fuel–air equivalence-ratio, it is possible to improve the “stability” of the combustion process by solely manipulating the pilot-fuel injection parameters while maintaining constant mass of injected pilot-fuel. This allows for tailoring mixing trajectories to offset changes in fuel ignition chemistry, so as to promote a robust transition from LTI to HTI by changing the balance between the local concentration of the pilot-fuel and richness of the premixed natural gas and air. This could prove to be a valuable tool for combustion design to improve fuel efficiency or reduce noise or perhaps even reduce heat-transfer losses by locating early combustion away from in-cylinder walls.

42 ENGINEERING↗

Modelling economic losses of historic and present-day high-impact winter windstorms in Switzerland

This study investigates the wind gusts and associated economic loss patterns of high-impact winter windstorms in Switzerland between 1871 and 2011. A novel approach for simulating windstorm-related gusts and losses at regional to local scales is applied to a sample of 84 windstorms. The approach involves the dynamical downscaling of the Twentieth Century Reanalysis (20CR) ensemble mean to 3-km horizontal grid size using the Weather Research and Forecasting (WRF) model. Economic losses are simulated at municipal level for present-day asset distribution based on the downscaled (parameterised) wind gusts at high spatiotemporal resolution using the open-source impact model climada. A comparison with insurance loss data for two recent windstorms (“Lothar” in 1999, “Joachim” in 2011) indicates that the loss simulation allows to realistically simulate the spatial patterns of windstorm losses. The loss amplitude is strongly underestimated for ‘Lothar’, while it is in reasonable agreement for ‘Joachim’. Possible reasons are discussed. Uncertainties concerning the loss simulation arise from the wind gust estimation method applied; estimates can differ considerably among the different methods, in particular over high orography. Furthermore, the quality of the loss simulation is affected by the underlying simplified assumptions regarding the distribution of assets and their susceptibilities to damage. For the whole windstorm sample, composite averages of simulated wind gust speed and loss are computed. Both composites reveal high values for the densely populated Swiss Plateau and lower values for south-eastern Switzerland; metropolitan areas stand out in the loss composite. Eight of the top 10 events concerning the losses simulated for present-day asset distribution and summed over all Swiss municipalities occurred after 1950. It remains uncertain whether this is due to decadal-scale changes of winter windstorms in Switzerland or merely due to a possible bias of the 20CR ensemble mean towards lower wind speeds in the period before around 1950.

20CR↗

Ion acoustic solitons in Earth's upward current region

The formation and evolution of ion acoustic solitons in Earth's auroral upward current region are studied using one- and two-dimensional (2D) electrostatic particle-in-cell simulations. The one-dimensional simulations are confined to processes that occur in the auroral cavity and include four plasma populations: hot electrons, H{sup +} and O{sup +} anti-earthward ion beams, and a hot H{sup +} background population. Ion acoustic solitons are found to form for auroral-cavity ion beams consistent with acceleration through double-layer (DL) potentials measured by FAST. A simplified one-dimensional model simulation is then presented in order to isolate the mechanisms that lead to the formation of the ion acoustic soliton. Results of a two-dimensional simulation, which include both the ionosphere and the auroral cavity, separated by a low-altitude DL, are then presented in order to confirm that the soliton forms in a more realistic 2D geometry. The 2D simulation is initialized with a U-shaped potential structure that mimics the inferred shape of the low altitude transition region based on observations. In this simulation, a soliton localized perpendicular to the geomagnetic field is observed to form and reside next to the DL. Finally, the 2D simulation results are compared with FAST data and it is found that certain aspects of the data can be explained by assuming the presence of an ion acoustic soliton.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Integrated Surface/subsurface flow modeling in PFLOTRAN

Understanding soil water, groundwater, and shallow surface water dynamics as an integrated hydrological system is critical for understanding the Earth’s critical zone, the thin outer layer at our planet’s surface where vegetation, soil, rock, and gases interact to regulate the environment. Computational tools that take this view of soil moisture and shallow surface flows as a single integrated system are typically referred to as integrated surface/subsurface hydrology models. We extend the open-source, highly parallel, subsurface flow and reactive transport simulator PFLOTRAN to accommodate surface flows. In contrast to most previous implementations, we do not represent a distinct surface system. Instead, the vertical gradient in hydraulic head at the land surface is neglected, which allows the surface flow system to be eliminated and incorporated directly into the subsurface system. This tight coupling approach leads to a robust capability and also greatly simplifies implementation in existing subsurface simulators such as PFLOTRAN. Successful comparisons to independent numerical solutions build confidence in the approximation and implementation. Example simulations of the Walker Branch and East Fork Poplar Creek watersheds near Oak Ridge, Tennessee demonstrate the robustness of the approach in geometrically complex applications. The lack of a robust integrated surface/subsurface hydrology capability had been a barrier to PFLOTRAN’s use in critical zone studies. This work addresses that capability gap, thus enabling PFLOTRAN as a community platform for building integrated models of the critical zone.

58 GEOSCIENCES↗

Importance of Body Stance in Fog Droplet Collection by the Namib Desert Beetle

The fog-basking behavior of the Onymacris unguicularis, a beetle species living in the coastal regions of the Namibian desert, has recently caught the attention of the engineering community, as suggesting a viable biomimetic approach to address the problem of harvesting water in arid regions of the globe. Previous research has focused on observation and analysis of the beetle’s elytron properties and how these affect fog-collection rates. The head stance taken by the Onymacris unguicularis when fog basking is well documented. However, how this stance affects droplet collection has not been studied up to now. The present paper addresses this problem from a computational fluid dynamics perspective, where three-dimensional numerical simulations are used to characterize the fog flow properties around a simplified geometry mimicking the beetle’s body. The simulations employ two-way coupling between the gas flow and the dispersed fog phase to account for feedback effects of fog droplets on the carrier fluid (air), and assume that droplets are captured after hitting the elytron surface. The study considers several combinations of free-stream velocity and droplet volume fraction. The analysis reveals that there is a range of head-stance angles, corresponding to an inclination of the beetle between 35 deg and 45 deg with respect to the horizon, that maximizes water collection on the beetle’s back, in qualitative agreement with observations in nature and laboratory experiments. A rationale is proposed to explain this phenomenon, finding that the specific head stance corresponds to the maximum residence time of fluid particles above the beetle’s elytron surface. This, in turn, designates the maximum likelihood for water droplets to be captured in the boundary layer developing over the beetle and subsequently hit the surface where they get captured. The results reveal the importance of the fluid flow pattern around the beetle’s body in addition to the microphysical properties of the elytron when reliable predictions of the water droplet collection efficiency are sought.

Chakrabarti, Unmeelan↗

Development of Methods to Evaluate Safer Flight Characteristics

The goal of the proposed research is to begin development of a simulation that models the flight characteristics of the Simplified Aid For EVA Rescue (SAFER) pack. Development of such a simulation was initiated to ultimately study the effect an Orbital Replacement Unit (ORU) has on SAFER dynamics. A major function of this program will be to calculate fuel consumption for many ORUs with different masses and locations. This will ultimately determine the maximum ORU mass an astronaut can carry and still perform a self-rescue without jettisoning the unit. A second primary goal is to eventually simulate relative motion (vibration) between the ORU and astronaut. After relative motion is accurately modeled it will be possible to evaluate the robustness of the control system and optimize performance as needed. The first stage in developing the simulation is the ability to model a standardized, total, self-rescue scenario, making it possible to accurately compare different program runs. In orbit an astronaut has only limited data and will not be able to follow the most fuel efficient trajectory; therefore, it is important to correctly model the procedures an astronaut would use in orbit so that good fuel consumption data can be obtained. Once this part of the program is well tested and verified, the vibration (relative motion) of the ORU with respect to the astronaut can be studied.

Basciano, Thomas E., Jr.↗

Cycle-to-Cycle Variations in Multi-Cycle Engine RANS Simulations

Reynolds-averaged Navier-Stokes (RANS) modeling is expected to deliver an ensemble-averaged result for the majority of turbulent flows. This could lead to the conclusion that multi-cycle internal combustion engine (ICE) simulations performed using RANS must exhibit a converging numerical solution after a certain number of consecutive cycles. However, for some engine configurations unsteady RANS simulations are not guaranteed to deliver an ensemble-averaged result. In this paper it is shown that, when using RANS modeling to simulate multiple engine cycles, the cycle-to-cycle variations (CCV) generated from different initial conditions at each cycle are not damped out even after a large number of cycles. A single-cylinder GDI research engine is simulated using RANS modeling and the numerical results for 20 consecutive engine cycles are evaluated for two specific operating conditions. One condition is characterized by stoichiometric operation and stable combustion (COVIMEP < 2%) and the other features dilute combustion resulting in misfire events and much higher COVIMEP. In both cases, multi-cycle RANS simulation results show cyclic variability. An in-depth analysis of the most significant physical and chemical quantities highlights that CCV are caused primarily by the variability of the in-cylinder flow. For stoichiometric combustion this does not greatly affect flame propagation, and the resulting fluctuations of the pressure traces are narrow. However, in the event of dilute combustion, the variability of the flow gains more importance, therefore delivering large cyclic fluctuations of in-cylinder pressure. Even though unsteady RANS simulations are not expected to predict as much variability in engine flows as LES, in particular for stable cases, they can still be used to capture typical combustion stability features in an internal combustion engine. This paper shows that the occurrence of CCV when using multi-cycle RANS modeling is not a numerical artifact or the effect of changes in the computational grid from cycle to cycle. Cold-flow analysis reveals that the variability of the simulated flow is intrinsic for the unsteady RANS approach and can only be damped out by increasing numerical viscosity, either by increasing the cell size or by adding up-winding. This is proved in a simplified non-ICE case such as the simulation of the vortex shredding from a cylinder in cross flow. Also, the effect of numerical viscosity on CCV is shown for multi-cycle engine simulations by using a simplified combustion model. Finally, it is shown that multi-cycle RANS can successfully predict the effect of changing specific engine parameters, such as the properties of the ignition system, on cyclic variability and combustion stability.

Scarcelli, Riccardo↗

Wave-packet manipulation of He Rydberg states by a seeded free-electron laser

We report a two-dimensional pump-control-probe spectroscopic study of the dynamics of singly excited He Rydberg-state wave packets with a seeded extreme ultraviolet (XUV) free-electron laser (FEL) source. A pair of coherent XUV pulses, defined by their coarse time separation and relative phase, created and manipulated the wave packets. The He atoms were postionized by infrared (IR) pulses, and the ion yield was measured as a function of XUV phase and IR arrival time. We tagged and sorted the relative phase of the XUV pulse pair on a single-shot basis by fitting each FEL spectrum with a suitable function that accounts for nonidealities of the XUV pulse pairs, associated with the seeding process; more generally, the fit returns the time-dependent electric field of the FEL spectra. The experimental two-dimensional maps of ion yields, measured as a function of IR (probe) delay and of XUV (pump-control) phase, were compared with the solution of the first-order time-dependent Schrödinger equation for this field. Despite the fact that the experimental conditions imply strong excitation, beyond the approximations of first-order perturbation theory, the simulated map satisfactorily reproduces the experimental one for temporally well-separated pulses. We show that by selecting data at appropriate values of pump-control phase, we enhance or suppress the amplitude of chosen wave-packet components consisting of two or more Rydberg states. When the temporal overlap of the pulse pair cannot be neglected, the phase reconstruction is underdetermined, and we provide a simplified comparison between data and simulations. Published by the American Physical Society 2024

Dumergue, Mathieu (ORCID:0000000236984406)↗

A simulation-based study on different control strategies for variable speed pump in distributed ground source heat pump systems

Most commercial ground source heat pump systems (GSHP) in the United States are in a distributed configuration. These systems circulate water or an anti-freeze solution through multiple heat pump units via a central pumping system, which usually uses variable speed pump(s). Variable speed pumps have potential to significantly reduce pumping energy use; however, the energy savings in reality could be far away from its potential due to improper pumping system design and controls. In this paper, a simplified hydronic pumping system was simulated with the dynamic Modelica models to evaluate three different pumping control strategies. This includes two conventional control strategies, which are to maintain a constant differential pressure across either the supply and return mains, or at the most hydraulically remote heat pump; and an innovative control strategy, which adjusts system flow rate based on the demand of each heat pump. The simulation results indicate that a significant overflow occurs at part load conditions when the variable speed pump is controlled to main a constant differential pressure across the supply and return mains of the piping system. On the other hand, an underflow occurs at part load conditions when the variable speed pump is controlled to maintain a constant differential pressure across the furthest heat pump. The flow-demand-based control can provide needed flow rate to each heat pump at any given time, and with less pumping energy use than the two conventional controls. Finally, a typical distributed GSHP system was studied to evaluate the energy saving potential of applying the flow-demand-based pumping control strategy. This case study shows that the annual pumping energy consumption can be reduced by 62% using the flow-demand-based control compared with that using the conventional pressure-based control to maintain a constant differential pressure a cross the supply and return mains.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Predicting Future Hourly Residential Electrical Consumption: A Machine Learning Case Study

Whole building input models for energy simulation programs are frequently created in order to evaluate specific energy savings potentials. They are also often utilized to maximize cost-effective retrofits for existing buildings as well as to estimate the impact of policy changes toward meeting energy savings goals. Traditional energy modeling suffers from several factors, including the large number of inputs required to characterize the building, the specificity required to accurately model building materials and components, simplifying assumptions made by underlying simulation algorithms, and the gap between the as-designed and as-built building. Prior works have attempted to mitigate these concerns by using sensor-based machine learning approaches to model energy consumption. However, a majority of these prior works focus only on commercial buildings. The works that focus on modeling residential buildings primarily predict monthly electrical consumption, while commercial models predict hourly consumption. This means there is not a clear indicator of which techniques best model residential consumption, since these methods are only evaluated using low-resolution data. We address this issue by testing seven different machine learning algorithms on a unique residential data set, which contains 140 different sensors measurements, collected every 15 minutes. In addition, we validate each learner's correctness on the ASHRAE Great Energy Prediction Shootout, using the original competition metrics. Our validation results confirm existing conclusions that Neural Network-based methods perform best on commercial buildings. However, the results from testing our residential data set show that Feed Forward Neural Networks, Support Vector Regression (SVR), and Linear Regression methods perform poorly, and that Hierarchical Mixture of Experts (HME) with Least Squares Support Vector Machines (LS-SVM) performs best - a technique not previously applied to this domain.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Cross-comparison of spacecraft-environment interaction model predictions applied to Solar Probe Plus near perihelion

Five spacecraft-plasma models are used to simulate the interaction of a simplified geometry Solar Probe Plus (SPP) satellite with the space environment under representative solar wind conditions near perihelion. By considering similarities and differences between results obtained with different numerical approaches under well defined conditions, the consistency and validity of our models can be assessed. The impact on model predictions of physical effects of importance in the SPP mission is also considered by comparing results obtained with and without these effects. Simulation results are presented and compared with increasing levels of complexity in the physics of interaction between solar environment and the SPP spacecraft. The comparisons focus particularly on spacecraft floating potentials, contributions to the currents collected and emitted by the spacecraft, and on the potential and density spatial profiles near the satellite. The physical effects considered include spacecraft charging, photoelectron and secondary electron emission, and the presence of a background magnetic field. Model predictions obtained with our different computational approaches are found to be in agreement within 2% when the same physical processes are taken into account and treated similarly. The comparisons thus indicate that, with the correct description of important physical effects, our simulation models should have the required skill to predict details of satellite-plasma interaction physics under relevant conditions, with a good level of confidence. Our models concur in predicting a negative floating potential V{sub fl}∼−10V for SPP at perihelion. They also predict a “saturated emission regime” whereby most emitted photo- and secondary electron will be reflected by a potential barrier near the surface, back to the spacecraft where they will be recollected.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Localizing Clinical Patterns of Blast Traumatic Brain Injury Through Computational Modeling and Simulation

Blast traumatic brain injury is ubiquitous in modern military conflict with significant morbidity and mortality. Yet the mechanism by which blast overpressure waves cause specific intracranial injury in humans remains unclear. Reviewing of both the clinical experience of neurointensivists and neurosurgeons who treated service members exposed to blast have revealed a pattern of injury to cerebral blood vessels, manifested as subarachnoid hemorrhage, pseudoaneurysm, and early diffuse cerebral edema. Additionally, a seminal neuropathologic case series of victims of blast traumatic brain injury (TBI) showed unique astroglial scarring patterns at the following tissue interfaces: subpial glial plate, perivascular, periventricular, and cerebral gray-white interface. The uniting feature of both the clinical and neuropathologic findings in blast TBI is the co-location of injury to material interfaces, be it solid-fluid or solid-solid interface. This motivates the hypothesis that blast TBI is an injury at the intracranial mechanical interfaces. In order to investigate the intracranial interface dynamics, we performed a novel set of computational simulations using a model human head simplified but containing models of gyri, sulci, cerebrospinal fluid (CSF), ventricles, and vasculature with high spatial resolution of the mechanical interfaces. Simulations were performed within a hybrid Eulerian—Lagrangian simulation suite (CTH coupled via Zapotec to Sierra Mechanics). Because of the large computational meshes, simulations required high performance computing resources. Twenty simulations were performed across multiple exposure scenarios—overpressures of 150, 250, and 500 kPa with 1 ms overpressure durations—for multiple blast exposures (front blast, side blast, and wall blast) across large variations in material model parameters (brain shear properties, skull elastic moduli). All simulations predict fluid cavitation within CSF (where intracerebral vasculature reside) with cavitation occurring deep and diffusely into cerebral sulci. These cavitation events are adjacent to high interface strain rates at the subpial glial plate. Larger overpressure simulations (250 and 500kPa) demonstrated intraventricular cavitation—also associated with adjacent high periventricular strain rates. Additionally, models of embedded intraparenchymal vascular structures—with diameters as small as 0.6 mm—predicted intravascular cavitation with adjacent high perivascular strain rates. The co-location of local maxima of strain rates near several of the regions that appear to be preferentially damaged in blast TBI (vascular structures, subpial glial plate, perivascular regions, and periventricular regions) suggest that intracranial interface dynamics may be important in understanding how blast overpressures leads to intracranial injury.

59 BASIC BIOLOGICAL SCIENCES↗

Correlations of the Elemental Compositions of Primary Coal Tar and Char

We report that simulations of large-scale coal combustors rely on accurate submodels to describe the chemical and physical changes in coal during reaction. Typically, researchers use simplified empirical submodels tuned to experimental data to reduce the computational complexity. When data are not readily available, researchers use simplifying assumptions, which can create inaccuracies and biases in a large simulation. One such simplifying assumption in coal research is how to describe the elemental composition of primary pyrolysis products. This paper explores several different empirical model forms to predict the dry, ash-free fractions of C, H, O, N, and S in both the char and the tar, using variables such as parent coal composition, reaction conditions (temperatures and particle residence times), and key coal structural parameters derived from NMR measurements. These model forms were correlated to existing data using a wide range of experimental data using a cross-validation procedure. Since coal structural values can be expensive to measure, several correlations from the literature were used to estimate these values based on information from the proximate and ultimate analyses of the parent coal, including a new correlation for the coal aromaticity. These model forms were tested against a set of measured elemental compositions of tar and char to find the best fit to use in the cross-validation process. Lastly, the best empirical models are presented that predict elemental composition of the coal char and tar after devolatilization.

01 COAL, LIGNITE, AND PEAT↗

Enabling Metric-Based Mesh Adaptation for Advanced Compressible Flow Simulations Using US3D

This work presents a metric-based mesh adaptation capability added to the flow solver US3D that is used to improve the accuracy of atmospheric entry simulations. Flow past an entry vehicle in free-flight is usually unsteady and characterized by anisotropic flow features like a strong bow shock and small-scale isotropic flow features like turbulent eddies in the wake. The results presented in this paper demonstrate that we are currently able to iteratively apply metric-based mesh adaptation to improve the solution accuracy by simultaneously targeting isotropic and anisotropic flow features. A simplified workflow of running CFD simulations for entry vehicles is presented where we start off with a coarse initial mesh to compute a first approximation of the flow. This coarse mesh is then iteratively refined using the newly developed metric to improve the resolution of the CFD computation. Furthermore, we demonstrate that we are able to adapt large mesh sizes in a timely fashion which allows us to start thinking about applying this adaptive framework to unsteady atmospheric entry CFD simulations.

Mesh adaptation↗