Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tensile Strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Mechanical characterization of Bi-2212 composite winding pack samples for high-field superconducting magnet design

Bi₂Sr₂CaCu₂O8−x (Bi-2212) multi-filament round wire is a high-temperature superconductor (HTS) capable of carrying high transport currents, which makes it suitable for high-field magnet applications. However, its weak Ag–Mg sheath leaves it vulnerable to mechanical stress, posing challenges for high-field magnet design. To better understand and improve mechanical stress management in Bi-2212 winding packs, we conducted an experimental study evaluating the axial stress–strain behavior of five winding pack configurations with varying insulation materials, reinforcement strategies, and construction quality. Using uniaxial tensile testing at 77 K, we measured Young’s modulus and Poisson’s ratio for each composition. Our results show that pure alumina braid insulation and co-wind reinforcements significantly enhance stiffness compared to aluminosilicate braids, with more than 2.5 times increased winding pack Young’s modulus. Rule of mixtures analysis further quantified the contribution of non-wire composite components to overall stiffness. These findings highlight the critical role of insulation material selection and reinforcement design in optimizing Bi-2212 coil performance under stress, providing a foundation for improved mechanical models and more reliable high-field HTS magnet designs.

Bi-2212 magnet↗
DOE OSTI2020

Tensile behavior and microstructural evolution of a Fe-25Ni-20Cr austenitic stainless steel (alloy 709) from room to elevated temperatures through in-situ synchrotron X-ray diffraction characterization and transmission electron microscopy

Uniaxial tensile tests were done on Fe-25Ni-20Cr Austenitic Stainless Steel (Alloy 709) along with in-situ synchrotron measurement at different temperatures (25 degrees C, 500 degrees C, 700 degrees C and 900 degrees C). The X-Ray diffraction data was collected in-situ in order to follow the phases present as well as to derive the dislocation density as a function of strain through peak broadening analysis based on the modified Williamson-Hall method and see how trends are affected as a function of temperature. The XRD data were complemented by TEM and STEM-EDX characterization done on the post-experiment samples to observe the deformed microstructures. Finally, the paper presents a depiction of the tensile behavior of this advanced steel by interpreting the stress-strain curves and the effect of temperature through the information gained by in-situ XRD and TEM observations as well as fractography done ex-situ on the samples tested to rupture.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Length scale effects of micro- and meso-scale tensile tests of unirradiated and irradiated Zircaloy-4 cladding

Zircaloy-4 is an essential material for cladding structures within fission-based reactors. To explore the changes in properties measured on differing length scales, FIB-machined micro-scale tensile tests were performed on both irradiated and control groups of Zircaloy-4. This was correlated with tensile testing on femtosecond laser-machined meso-scale specimens. Pronounced size effects were found when varying specimen geometry. Increases in tensile geometry size were associated with a reduction in measured yield stress for both irradiated and unirradiated samples. Here, meso-scale testing found strength and strain values similar to that of bulk-scale testing.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Synergy of tensile strength and high cycle fatigue properties in a novel additively manufactured Al-Ni-Ti-Zr alloy with a heterogeneous microstructure

Alloy design strategies in additive manufacturing (AM) to achieve grain refinement and terminal eutectic solidification have been introduced to engineer Al alloys having microstructural hierarchy and heterogeneity. Such alloy design strategies enable crack-free builds with an expanded AM processing window and pushed the strength limit in Al alloys. However, fatigue performance of Al alloys made by AM is restricted by the presence of process induced defects and its stochasticity. In this work, tensile and high cycle fatigue (HCF) behavior of a novel Al-Ni-Ti-Zr alloy with a heterogeneous microstructure is studied in the as-built condition, supplemented by detailed microstructural and mechanical characterization. Excellent strength-ductility synergy of 342 MPa and 16% failure strain achieved in the alloy was associated with the microstructural attributes that pertain to the novel alloy. Additionally, the alloy showed excellent HCF performance with a fatigue endurance limit to ultimate tensile strength ratio of 0.29 in flexural fatigue mode. The study revealed the existence of multiple crack retardation mechanisms and favorable crack propagation pathways through the fine-grained regions which enabled good fatigue performance to the alloy. Further, a probabilistic model has been used to estimate the fatigue life of the alloy as a function of the stochastic microstructure by utilizing the statistical distribution of pores, solid-state inclusions, and grains in the AM Al alloy. Finally, the model parametric trends are consistent with the experimental observations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Structure/property relationship of semicrystalline polymers during tensile deformation: a molecular dynamics approach

Molecular dynamics (MD) simulation with an ab initio numerical model is conducted to study the structure–property relationship of semicrystalline polymers during uniaxial deformation. The effects of chain length, temperature, and strain rate on mechanical properties are discussed. The influences of microstructural evolution such as bond length, entanglement density, and chain orientation are also studied quantitatively. The temperature will greatly affect the chain conformation in amorphous domains, and the results revealed that the interaction of amorphous and crystalline domains played a crucial role during stretching. Accordingly, the yielding of semicrystalline polymers follows different mechanisms at temperatures above and below T g . A melt-recrystallization scheme is observed during yielding at higher temperatures, while destruction of crystal structures is observed at lower temperatures at the yield point. The correlated effects of different temperatures and strain rates on mechanical properties are examined. This research is part of our efforts to develop a digital twin of a real experiment for efficient optimization of polymer material properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Notch-tensile behavior of Al0.1CrFeCoNi high entropy alloy

Notch-tensile behavior of an Al0.1CrFeCoNi high entropy alloy (Al0.1-HEA) was studied using V-notch geometry and with local strain mapping using digital image correlation (DIC). A notch-strength ratio of 1.51 indicated notch strengthening. Further analysis of stress-strain response supplemented with microstructural analysis revealed that, while the presence of notch results in strengthening due to work hardening by twinning induced plasticity, the notch also contributes strongly to geometrical softening in the non-uniform ductility regime, and accounts for the onset of failure. The strain localization behavior of Al0.1-HEA due to the presence of V-notch was compared with three conventional alloys: Inconel 625 nickel-based superalloy, 304 stainless steel and Ti–6Al–4V titanium alloy. The study revealed that the nature of notch widening with increasing strain was dependent on material characteristics. The extent of notch widening impacted the local strain field and stress distribution, thereby influencing the propensity for crack initiation and growth. The experimental results were verified by finite element analysis.

Sinha, Subhasis↗
DOE OSTI2023

Orientation dependence of the effect of short-range ordering on the plastic deformation of a medium entropy alloy

Multi-principal-element alloys (also known as medium and high entropy alloys) offer a much larger and richer design space than conventional alloys, providing opportunities for discovering new functionalities and their governing physics. Some of these alloys exhibit an outstanding combination of high strength and ductility, linked to the activation of various deformation modes triggered by low-energy stacking faults. However, a pressing question remains: Is the plasticity of medium- and high-entropy alloys governed only by stacking fault energy, or does atomic short-range order (SRO) play a role? Here, to answer this, we investigated how SRO affects the deformation in single-crystalline NiCoCr, with previous contradictory findings. First, we established unique experimental evidence for SRO formation in bulk single crystals using high-energy synchrotron transmission X-Ray Diffraction. By tuning the degree of SRO by aging at high temperatures, twinning density and strain-induced martensitic phase transformation can be significantly increased in the [110] and [111] orientations under tension, increasing the tensile ductility; yet, no increase was observed along the [001] orientation due to lack of TWinning-Induced Plasticity (TWIP) or TRansformation-Induced Plasticity (TRIP), indicating a strong crystallographic orientation dependence. Our first-principles thermodynamic calculations unequivocally show SRO exists and governs the observed microstructural evolution and deformation hardening behavior. Here we find direct proof that SRO triggers a simultaneous TWIP and TRIP in NiCoCr, a rare microstructural evolution path. Our findings establish that the interplay of SRO and plasticity could be exploited to alter deformation modes and yield unprecedented mechanical response in medium- and high-entropy alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effects of particle inclusions on cracking in ultrathin barrier films

Here, the effects of particle inclusions with different mechanical properties on the development of cracks in ultra-thin barrier films have been studied. Two types of particles, alumina and poly(styrene-b-methyl methacrylate) with large differences in their elastic modulus were used, representing both hard and soft inclusions. Particles were seeded onto polyethylene naphthalate substrates and subsequently coated with atomic layer deposited Al 2 O 3 as a barrier film. Ca corrosion tests used to determine the performance of the barrier films revealed that soft polymer particle inclusions severely affect the development of cracking in barrier films as compared to stiff ceramic particles. Tensile tests also confirmed that the barrier films with polymer particle inclusions have the lowest value of critical onset strain. Parametric simulations, conducted by varying the elastic modulus of the particle inclusions over a wide range, resulted in a larger strain energy release rate near particle inclusions which promotes crack formation and negatively impacts the performance of barrier films with softer particle inclusions. Thus, the combination of high residual stresses in the barrier films with the presence of soft particle inclusions is found the most detrimental for the development of high-performance ultrathin barrier films.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of Strain Rate and Temperature on the Mechanical Properties of Simulated Silica Ionogels

Ionogels are hybrid materials formed by impregnating the pore space of a solid matrix with a conducting ionic liquid. By combining the properties of both component materials, ionogels can act as self-supporting electrolytes in Li batteries. In this study, molecular dynamics simulations are used to investigate the dependence of mechanical properties of silica ionogels on solid fraction, temperature, and pore width. Comparisons are made with corresponding aerogels. We find that the solid matrix fraction increases the moduli and strength of the ionogel. This varies nonlinearly with temperature and strain rate, according to the contribution of the viscous ionic liquid to resisting deformation. Additionally, owing to the temperature and strain sensitivity of the ionic liquid viscosity, the mechanical properties approach a linear mixing law at high temperature and low strain rates. The median pore width of the solid matrix plays a complex role, with its influence varying qualitatively with deformation mode. Narrower pores increase the relevant elastic modulus under shear and uniaxial compression but reduce the modulus obtained under uniaxial tension. Conversely, shear and tensile strength are increased by narrowing the pore width. All of these pore size effects become more pronounced as the silica fraction increases. Pore size effects, similar to the effects of temperature and strain rate, are linked to the ease of fluid redistribution within the pore space during deformation-induced changes in the geometry of the pores.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

In situ high-energy X-ray study of deformation mechanisms in additively manufactured 316L stainless steel

A key structural material planned to be used in the core of the Transformational Challenge Reactor is the additively manufactured 316L stainless steel (AM 316L SS). While the deformation of conventionally-manufactured 316 SS have been extensively studied, the deformation mechanism of AM 316L SS is less known. Here the room-temperature tensile behavior of AM 316L SS was studied in situ using high-energy X-ray diffraction and X-ray tomography. Diffraction yielded the lattice strains and the dislocation densi-ties of the AM 316L SS, which were compared to those of a conventionally processed 316H SS. It was found that while the conventional 316H SS had three distinct deformation stages, namely stage II ather-mal hardening, stage III dynamic recovery, and stage IV, the AM 316L experienced only the stages III and IV after an initial transitional period. The plastic instability stresses (PIS), i.e. the true ultimate tensile strength, were nearly the same in both materials. The AM 316L had very low dislocation barrier strength throughout the plastic deformation, which, in combination with the invariant PIS, explained its high dis-location storage capability and the attractive combination of strength and ductility. Tomography revealed morphological changes of the built-in pores in the AM 316L during deformation and fracture, and it was concluded that large pores close to the surface might have significant roles in the necking stage.

316 stainless steel↗
DOE OSTI2021

Dynamic recrystallization of a wrought magnesium alloy: Grain size and texture maps and their application for mechanical behavior predictions

Effect of dynamic recrystallization (DRX) on the grain refinement and texture modification was studied by conducting a series of hot compression on AZ31B Mg alloy. Processing-grain size-texture maps were established as a function of temperature, strain rate, strain, and the Zener-Hollomon parameter (Z). Moreover, influence of simultaneous changes in the grain size and texture on tensile yield strength and ductility of the hot-worked Mg alloy was studied using the grain size and texture maps established. The processing-grain size map showed that the DRX grain size decreased with the increase in Z, also revealing various characteristics ranging from a grain growth, grain refinement, to a bimodal distribution of ultrafine grains and partially recrystallized grains. The effect of twinning on the grain refinement was also evident at high Z conditions. The processing-texture map revealed that the initial fiber texture was altered significantly to a shear, off-normal, or extension-twin texture with the increase in Z. The Schmid-factor maps were calculated to identify a dominant deformation mode during a subsequent tensile deformation of the hot-worked samples. Finally, a corresponding Hall-Petch relationship for each dominant deformation mode was used to establish tensile yield-strength maps, which agree well with the measured data.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Accounting for the effect of dislocation climb-mediated flow on the anisotropy and texture evolution of Mg alloy, AZ31B

The current study explores the role that dislocation climb has in mediating plasticity a Mg alloy at moderately elevated temperatures. Interrupted tensile tests were performed on samples of Mg alloy, AZ31B, sheet in the O temper condition over a range of strain rates (10 -5 to 10 -1 s -1 ) and temperatures (20–350°C) along the rolling and transverse directions. Experimental measurements of the resulting strain anisotropy and texture evolution were used as constraints during a parametric study employing a new crystal plasticity model (VPSC-CLIMB), which explicitly accounts for the kinematics of dislocation climb. The results reveal that the climb of basal (a) dislocations is not only important for dislocation recovery, but also demonstrate that climb accommodates a significant fraction of the strain in conditions where a power-law creep-type constitutive response prevails. This work does not discredit the notion that non-basal slip of (a) and (c+a) dislocations is important over a wide range of temperatures and strain rates. However, it demonstrates that the activation of dislocation climb as the mechanistic change within the power law regime provides an explanation for a wide range of observations, including the simultaneous reduction in strain anisotropy, slowed texture evolution, and rapid increase in strain rate sensitivity. Finally, it is hypothesized that these conclusions may even apply to cases in which grain boundary sliding and/or dynamic recrystallization are observed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Inversion-based correction of Double-Torsion (DT) subcritical crack growth tests for crack profile geometry

Because of its simplicity and the ability to produce a stable, slow-propagating crack, the Double-Torsion (DT) method has been used widely for investigating the critical and subcritical propagation of a slow-propagating tensile (mode-I) crack. However, to determine the complex relationship between the crack velocity $\mathcal{v_c}$ vs. the strain energy release rate $\mathscr{G}$ (or the stress intensity factor K) from laboratory measurements, several corrections must be made to account for the impact of sample and crack geometry. Particularly, DT test typically produces a crack with a curved edge profile instead of a straight line, causing the local $\mathcal{v_c}$ and $\mathscr{G}$ vary along the crack front. The experimentally measured $\mathcal{v_c}$ and $\mathscr{G}$ data merely reflect collective, averaged behavior of the crack. This makes inversion for the intrinsic, “true” crack growth kinetics necessary, based upon the knowledge of the crack geometry. Simple and effective correction methods have been proposed and validated for the slow, chemical-reaction-controlled part (Region I) of the $\mathcal{v_c}$-$\mathscr{G}$ curve. However, reliable methods for the highly nonlinear, transport-dominated part (Region II) and its sudden transition to the dynamic propagation part (Region III) are still lacking. Here we propose a method for determining the intrinsic $\mathcal{v_c}$-$\mathscr{G}$ relationship across all three Regions based upon DT test data, using a simple model function and its numerical inversion. The performance of this approach is examined and demonstrated using both synthetic and laboratory data for subcritical crack growth in soda lime glass.

42 ENGINEERING↗
DOE OSTI2022

Ring Pull Strain Analysis

Ring Pull Strain Analysis (RPSA) is a framework for analysis of Digital Image Correlation (DIC) data of gaugeless ring pull testing. It is meant for analysis of rings cut from tube cross sections and pulled in a displacement-controlled tensile test. This code takes load frame data, images take during testing, and csv files from the DIC analysis of those images and allows the user to analyze and plot data from the test. Some important features of the software include getting the strain values as a function of radial distance and angle, plotting of the strain around the ring, and stress-strain analysis of the load frame data.

Beck, Peter↗
DOE OSTI2024

Ring Pull Strain Analysis

Ring Pull Strain Analysis (RPSA) is a framework for analysis of Digital Image Correlation (DIC) data of gaugeless ring pull testing. It is meant for analysis of rings cut from tube cross sections and pulled in a displacement-controlled tensile test. This code takes load frame data, images take during testing, and csv files from the DIC analysis of those images and allows the user to analyze and plot data from the test. Some important features of the software include getting the strain values as a function of radial distance and angle, plotting of the strain around the ring, and stress-strain analysis of the load frame data. Additional capability is included with Ring Pull Coating Analysis (RPCA, also part of the software). Additional images are taken of samples with an outer coating and are used to correlate failure of the coating with strain values measured with DIC.

Beck, Peter↗
DOE OSTI2020

Lattice strains and diffraction elastic constants of cubic polycrystals

In situ synchrotron X-ray and neutron diffraction experiments provide a powerful approach to measure lattice strains in bulk polycrystalline materials. They are being increasingly used for quantitative characterization of microscale deformation within and between grains and phases. Here we use a self-consistent micromechanics model to obtain a general analytic solution of the grain-level lattice strains and diffraction elastic constants for a broad class of elastically isotropic polycrystals with cubic crystal symmetry. This analytic solution reveals a direct linear relationship between the reciprocal of the elastic diffraction constant and the orientation index parameter along the direction of any diffraction vector, including tensile loading and transverse directions. The straightforward numerical implementation of this solution provides diffraction elastic constants for 26 representative cubic polycrystals. Finally, analytic solutions of this kind can serve to benchmark in situ diffraction measurements of lattice strains and also facilitate high-throughput studies of microscale stresses and diffraction elastic constants in polycrystalline materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Electronic Excitation‐Driven β‐Ga 2 O 3 Metastability Transformation and Self‐Organization Mechanism: β→κ/γ/δ Phases

Here, irradiation-driven multiphase self-organization presents emergent opportunities for the customization of nanoscale engineering properties, dynamically tuning strain-field distributions and interfacial electronic structures. Responding to intense electronic excitation-induced energy deposition, the dominant phase transformations, with varying Gibbs free energy $Δ,G^o_f$ are confirmed as β → κ → γ → δ that are located in specific microregions for Gallium (III) oxide (Ga 2 O 3 ), as follows: (i) Surface-localized interstitial accumulation under compressive stress triggers β → δ via semi-coherent interface formation. (ii) Tensile stress within latent tracks drives vacancy-mediated oxygen layer truncation (4/12 periodicity along ⟨0001⟩), stabilizing coherent 4H (ABCB) κ and 3C (ABC) β (ABC) interfaces through strain-compensated octahedral distortion. (iii) Screw dislocation-mediated lattice relaxation induces β → γ via cation disordering (Ga 3+ occupancy at β-interstitial sites), forming metastable spinel γ with mixed occupancy across 16d/8a Wyckoff sites. Irradiation-driven β-Ga 2 O 3 →κ/γ/δ transitions, as mechanistically revealed via inelastic thermal spike (i-TS) calculations and molecular dynamics simulations, induce defect-mediated nonlinear photoresponse, critical for optoelectronic engineering.

Han, Xinqing [Shandong Univ., Jinan (China)]↗