Search NASA⌕ Search

SEARCH · Search NASA

Results for “Time Calibration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Development of a drift-correction procedure for a direct-reading spectrometer

A procedure which provides automatic correction for drifts in the radiometric sensitivity of each detector channel in a direct-reading emission spectrometer is described. Such drifts are customarily controlled by the regular analyses of standards, which provide corrections for changes in the excitational, optical, and electronic components of the instrument. This standardization procedure, however, corrects for the optical and electronic drifts. It is a step that must be taken if the time, effort, and cost of processing standards is to be minimized. This method of radiometric drift correction uses a 1,000-W tungsten-halogen reference lamp to illuminate each detector through the same optical path as that traversed during sample analysis. The responses of the detector channels to this reference light are regularly compared with channel response to the same light intensity at the time of analytical calibration in order to determine and correct for drift. Except for placing the lamp in position, the procedure is fully automated and compensates for changes in spectral intensity due to variations in lamp current. A discussion of the implementation of this drift-correction system is included.

Chapman, G. B., II↗

A digital goniometer for VOR

A new VOR (VHF omni-range) goniometer design which promises to improve the reliability and maintainability of the VOR ground station is described. The heart of the new concept is the use of two digital phase shifters to produce the rotating figure-of-eight pattern of conventional VOR. Using digital circuits, the goniometer adjustments and calibration reduce to timing adjustments of binary signals. A common clock used for timing the digital phase shifters also synchronizes the 30 Hz modulation of the 9.96 kHz reference.

Meer, S. A.↗

Development of an in situ calibration technique for combustible gas detectors

This paper describes the development of an in situ calibration procedure for combustible gas detectors (CGD). The CGD will be a necessary device for future space vehicles as many subsystems in the Environmental Control/Life Support System utilize or produce hydrogen (H2) gas. Existing calibration techniques are time-consuming and require support equipment such as an environmental chamber and calibration gas supply. The in situ calibration procedure involves utilization of a water vapor electrolysis cell for the automatic in situ generation of a H2/air calibration mixture within the flame arrestor of the CGD. The development effort concluded with the successful demonstration of in situ span calibrations of a CGD.

Shumar, J. W.↗

Development of a drift-correction procedure for a photoelectric spectrometer

A technique has been developed to automatically correct for drifts in the radiometric sensitivity of the detector channels in a direct-reading emission spectrometer. The method utilizes a 1000 W tungsten-halogen reference lamp to illuminate the detectors through the same optical path as that traversed during the analysis of the sample. Detector channel responses to the light are compared to those for the same light intensity at the time of analytical calibration. This corrects for the drift. It is noted that with the exception of positioning the lamp, the procedure is fully automatic.

Chapman, G. B., II↗

The local interstellar helium density - Corrected

An upper bound for the number density of neutral helium in the local interstellar medium of 0.004 + or - 0.0022 per cu cm was previously reported, based on extreme-ultraviolet telescope observations at 584 A made during the 1975 Apollo-Soyuz Test Project. A variety of evidence is found which indicates that the 584-A sensitivity of the instrument declined by a factor of 2 between the last laboratory calibration and the time of the measurements. The upper bound on the helium density is therefore revised to 0.0089 + or - 0.005 per cu cm.

Freeman, J.↗

Results and analyses of ground-based and satellite ozone observations A review

The ground-based network that has been in existence for several decades is described. Attention is given to two basic questions, namely the way in which monthly satellite analyses compare with those from the ground-based network and the way in which the trends from the satellite and ground-based data compare. Synoptic analyses of total ozone for December 1970 are compared with a subjective analysis of the ground-based network and an objective backscatter ultraviolet (BUV) analysis. It is found that the BUV analysis is the more consistent of the two. Considering monthly analyses for September 1970, satellite and ground-based data are found to agree quite well. In considering the question of trend determination by the ground-based versus the satellite systems, attention is given to the sources of error in the satellite system. The principal sources of error in BUV analysis are thought to be calibration drift with time and the fact that, over the lifetime of the satellite spacecraft, power limitations result in a decrease in the number of data points per month, possibly with significant gaps in the coverage.

Miller, A. J.↗

Operational radio interferometry observation network (ORION) mobile VLBI station

The design and current status of the ORION mobile VLBI station is described. The station consists of a five-meter antenna, a receiving and recording system installed in a mobile antenna transporter, and an electronics transporter. The station is designed for field operation by a two-person crew at the rate of two sites per week. The various subsystems are described in detail, including the antenna, housing facilities for electronics and crew, microwave equipment, receiver, data acquisition subsystem, frequency and timing subsystem, phase calibration, monitoring and control, water vapor radiometer, and communications.

Renzetti, N. A.↗

Satellite sensing of aerosol absorption

A method is developed for remote sensing of aerosol absorption from satellite images of the earth's surface. The method is based on the measurement of the change in the upward radiances between a clear and a hazy day over a varying surface reflectance. For a zero change balance between brightening due to scattering and darkening due to absorption and scattering is reached. This balance is utilized via a radiative transfer model to derive the aerosol single-scattering albedo. A sensitivity study is performed, and the method is tested against laboratory measurements. It is suggested that for the case of haze introduced on top of an existing background aerosol and with a fair estimate of the scattering phase function, the error in the remotely sensed single-scattering albedo is in the range of 0.03-0.05. The main errors in the method arise from variations in the surface reflectance between the clear and the hazy days, uncertainty in the scattering phase function, and variation of the aerosol and gaseous absorption between these two days. If the satellite calibration varies with time, the measurements of single-scattering albedo can be substantially affected.

Kaufman, Yoram J.↗

Statistical study of thermal fracture of ceramic materials in the water quench test

The Weibull statistical theory of fracture was applied to thermal shock of ceramics in the water quench test. Transient thermal stresses and probability of failure were calculated for a cylindrical specimen cooled by convection. The convective heat transfer coefficient was calibrated using the time to failure which was measured with an acoustic emission technique. Theoretical failure probability distributions as a function of time and quench temperature compare favorably with experimental results for three high-alumina ceramics and a glass.

Rogers, Wayne P.↗

Charge exchange of low-energy ions in thin carbon foils

In order to calibrate a time-of-flight mass spectrometer which is to be flown in the solar wind, the charge exchange properties of low-energy ions in thin carbon foils have been investigated. Incident ions of He, C, N, O, Ne, and Ar with energies in the range 0.5-2 keV/nucleon have been used to measure charge-state distribution, residual energy, and angular distribution after transmission through thin (1-6 microgram/sq cm) carbon foils. Within such foils, an equilibrium between ionization and recombination of the projectile is rapidly established, and, consequently, the charge state of the emerging particle depends essentially on its residual velocity. A comparison of the charge exchange properties of Ne-22 with Ne-20 demonstrates that indeed the velocity (and not the energy) of the emerging particle determines its final charge. A comparison of properties of different elements provides an indication of an electron shell effect. Predictions for the energy loss of ions within the carbon foils made with the TRIM code are in good agreement with the experimental results presented in this paper.

Buergi, Alfred↗

Radiometric calibration and monitoring of NOAA AVHRR visible data

Results and corrections to calibration for the NOAA-7, -8, -9, -10, and -11 AVHRR Channel 1 data, covering the period from July 1983 through December 1989, are presented. Results from the NOAA-7 and NOAA-9 analysis are used as examples to illustrate key points and present detailed results. In the AVHRR monitor procedure, the spatial variability index is calculated first to classify the data as CLEAR or CLOUD. This classification is then used to sort the data to produce three 1D radiance histograms for different surface types. The surface reflectances are retrieved from the radiances, and a set of reflectance filters are applied to sort the data into global surface reflectance maps. An examination of the NOAA-7 results shows that the NOAA-7 radiometer sensitivity actually decreased at a rate of about 0.5-1.0 percent per year. Trends inferred from the point measurements representing independent calibrations at different times, using models, known sites, and coincident aircraft measurements, agree well with the satellite methods.

Brest, Christopher L.↗

A prediction of Mars seismicity from surface faulting

The shallow seismicity of Mars has been estimated by measurement of the total slip on faults visible on the surface of the planet throughout geologic time. Seismicity was calibrated with estimates based on surface structures on the moon and measured lunar seismicity that includes the entire seismogenic lithosphere. Results indicate that Mars is seismically active today, with a sufficient number of detectable marsquakes to allow seismic investigations of its interior.

Golombek, Matthew P.↗

Experimental investigation of nozzle/plume aerodynamics at hypersonic speeds

Much of the work involved the Ames 16-Inch Shock Tunnel facility. The facility was reactivated and upgraded, a data acquisition system was configured and upgraded several times, several facility calibrations were performed and test entries with a wedge model with hydrogen injection and a full scramjet combustor model, with hydrogen injection, were performed. Extensive CFD modeling of the flow in the facility was done. This includes modeling of the unsteady flow in the driver and driven tubes and steady flow modeling of the nozzle flow. Other modeling efforts include simulations of non-equilibrium flows and turbulence, plasmas, light gas guns and the use of non-ideal gas equations of state. New experimental techniques to improve the performance of gas guns, shock tubes and tunnels and scramjet combustors were conceived and studied computationally. Ways to improve scramjet engine performance using steady and pulsed detonation waves were also studied computationally. A number of studies were performed on the operation of the ram accelerator, including investigations of in-tube gasdynamic heating and the use of high explosives to raise the velocity capability of the device.

Bogdanoff, David W.↗

Applications of Temperature and Pressure Sensitive Paints

Luminescent molecular probes imbedded in a polymer binder form a temperature or pressure paint. On excitation by light of the proper wavelength, the luminescence, which is quenched either thermally or by oxygen, is detected by a camera or photodetector. From the detected luminescent intensity, temperature and pressure can be determined. The basic photophysics, calibration, accuracy and time response of a luminescent paint is described followed by applications in low speed, transonic, supersonic and cryogenic wind tunnels and in rotating machinery.

Liu, Tian-Shu↗

Pressure and Temperature Sensitive Paint Measurements on Rotors

Luminescent molecular probes imbedded in a polymer binder form a temperature or pressure paint. On excitation by light of the proper wavelength, the luminescence, which is quenched either thermally or by oxygen, is detected by a camera or photodetector. From the detected luminescent intensity, temperature and pressure can be determined. The basic photophysics, calibration, accuracy and time response of luminescent paints is described followed by applications in wind tunnels and in rotating machinery.

Sullivan, John↗

Uncertainty Analysis of Instrument Calibration and Application

Experimental aerodynamic researchers require estimated precision and bias uncertainties of measured physical quantities, typically at 95 percent confidence levels. Uncertainties of final computed aerodynamic parameters are obtained by propagation of individual measurement uncertainties through the defining functional expressions. In this paper, rigorous mathematical techniques are extended to determine precision and bias uncertainties of any instrument-sensor system. Through this analysis, instrument uncertainties determined through calibration are now expressed as functions of the corresponding measurement for linear and nonlinear univariate and multivariate processes. Treatment of correlated measurement precision error is developed. During laboratory calibration, calibration standard uncertainties are assumed to be an order of magnitude less than those of the instrument being calibrated. Often calibration standards do not satisfy this assumption. This paper applies rigorous statistical methods for inclusion of calibration standard uncertainty and covariance due to the order of their application. The effects of mathematical modeling error on calibration bias uncertainty are quantified. The effects of experimental design on uncertainty are analyzed. The importance of replication is emphasized, techniques for estimation of both bias and precision uncertainties using replication are developed. Statistical tests for stationarity of calibration parameters over time are obtained.

Tripp, John S.↗

Boundary-Layer Transition Detection in Cryogenic Wind Tunnel Using Fluorescent Paints

Luminescent molecular probes imbedded in a polymer binder form a temperature or pressure paint. On excitation by light of the proper wavelength, the luminescence, which is quenched either thermally or by oxygen, is detected by a camera or photodetector. From the detected luminescent intensity, temperature and pressure can be determined. The basic photophysics, calibration, accuracy and time response of a luminescent paints is described followed by applications in low speed, transonic, supersonic and cryogenic wind tunnels and in rotating machinery.

Sullivan, John↗

Computer Modeling of Electrostatic Aggregation of Granular Materials in Planetary and Astrophysical Settings

Electrostatic forces strongly influence the behavior of granular materials in both dispersed (cloud) systems and semi-packed systems. These forces can cause aggregation or dispersion of particles and are important in a variety of astrophysical and planetary settings. There are also many industrial and commercial settings where granular matter and electrostatics become partners for both good and bad. This partnership is important for human exploration on Mars where dust adheres to suits, machines, and habitats. Long-range Coulombic (electrostatic) forces, as opposed to contact-induced dipoles and van der Waals attractions, are generally regarded as resulting from net charge. We have proposed that in addition to net charge interactions, randomly distributed charge carriers on grains will result in a dipole moment regardless of any net charge. If grains are unconfined, or fluidized, they will rotate so that the dipole always induces attraction between grains. Aggregates are readily formed, and Coulombic polarity resulting from the dipole produces end-to-end stacking of grains to form filamentary aggregates. This has been demonstrated in USML experiments on Space Shuttle where microgravity facilitated the unmasking of static forces. It has also been demonstrated in a computer model using grains with charge carriers of both sign. Model results very closely resembled micro-g results with actual sand grains. Further computer modeling of the aggregation process has been conducted to improve our understanding of the aggregation process, and to provide a predictive tool for microgravity experiments slated for Space Station. These experiments will attempt to prove the dipole concept as outlined above. We have considerably enhanced the original computer model: refinements to the algorithm have improved the fidelity of grain behavior during grain contact, special attention has been paid to simulation time steps to enable establishment of a meaningful, quantitative time axis, and calibration of rounding accuracies have been conducted to test cumulative numerical influences in the model. The model has been run for larger grain populations, variable initial cloud densities, and we have introduced random net charging to individual grains, as well as a net charge to the cloud as a whole. The model uses 3 positive and 3 negative charges randomly distributed on each grain, with up to 160 grains contained within various size "boxes" that define the initial number densities in the clouds. Each charge represents localized charged region on a grain, but does not necessarily imply single quantized charge carriers. The Coulomb equations are then allowed to interact for each monopole: dipoles and any higher order charge coupling is a natural product of these "free" interactions over which the modeler exerts no influence. The charges are placed on surfaces of grains at random locations. A series of runs was conducted for neutral grains that had a perfect balance of negative and positive char carriers. Runs were also conducted with grains having additional fractional charges ranging between 0 and 1. By adding fractional charges of one sign, the model created grain populations in which all grains had excess charges the same sign, giving the cloud an overall net charge. This simulates clouds subjected to ionizing radiation (e. protoplanetary debris disk around a protosun), or any other process of charge biasing in a grain population (e.g., volcanic plumes). In another run series, random fractional charges of either sign were added to the grains so th some grains had a slight net positive charge while others had a slight net negative charge. This simulates triboelectrically-charged grain populations in which acquisition of an electron by one surface is at the expense creating a hole elsewhere. This dual sign charging was applied in two ways: in one case the cloud remained neutral by ensuring that all grain excess charges added to zero; in the other case, the cloud was permitted slight net char by not imposing a charge-balance condition. Additional information is contained in the original.

Marshall, J.↗