Search NASA⌕ Search

SEARCH · Search NASA

Results for “Transitional Flight”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Transition Delay via Vortex Generators in a Hypersonic Boundary Layer at Flight Conditions

The potential of realizable, stationary streaks undergoing non-modal growth to stabilize a hypersonic boundary-layer flow and, subsequently, delay the laminar-turbulent transition onset, is studied via numerical computations. The geometry and flow conditions are selected to match a relevant trajectory location from the ascent phase of the HIFiRE-1 flight experiment, namely, a 7-degree half-angle cone with 2.5 mm nose radius, freestream Mach number of 5.30, freestream unit Reynolds number equal to 13.42 x 10(exp 6)/m, and wall-to-adiabatic temperature ratio of approximately 0.35 over most of the test article. This paper investigates flow modifications induced by wall-mounted vortex generators (VGs), followed by an analysis of the modal instability of the perturbed, streaky boundary-layer flow. Results are presented both for a single array of VGs that was designed on the basis of optimal growth theory and for a VG configuration involving two separate arrays with opposite orientations that ware designed to provide staged control of flow instabilities while simultaneously reducing the amplification of streak instabilities resulting from the control devices. Earlier research had shown that the onset of transition during the HIFiRE-1 flight experiment, which did not include any control devices, correlated with an amplification factor of N = 14.7 for the planar Mack modes. If one assumes that the transition N -factor is not affected by the introduction of the VGs, then the control configurations based on a single array of VGs and two separate arrays would result in a transition delay of 17% and 40%, respectively. These findings suggest a passive flow control s to induce streaks that would delay transition in hypersonic boundary dominated by Mack-mode instabilities.

Incompressible boundary layer↗
NASA NTRSDate not supplied

A Distributed Simulation-to-Flight Framework to Support Investigating Trust/Trustworthiness in Multi-Agent Systems

As autonomous systems continue to grow both in use and complexity, the necessity for robust and extensible simulation-to-flight frameworks is paramount for establishing an effective architecture for autonomous systems. Hardware test flights are time-consuming and cost prohibitive during early system design and development. Simulation environments can be useful tools to accelerate algorithm development and testing. However, transitions from simulation to flight (sim-to-flight) can be challenging, unless systems are designed with this transition in mind and with the necessary capabilities built into the architecture and framework. One of the objectives of Autonomy Teaming and TRAjectories for Complex Trusted Operational Reliability (ATTRACTOR) was to design and develop a distributed mixed-reality simulation environment to begin establishing a basis for certification of autonomous systems via research into trust and trustworthiness. ATTRACTOR’s objective was to construct computational concepts of trustworthiness and justifiable trust in multi-agent autonomous teams, to inform future certification of safety-critical and time-critical autonomous systems in aviation. In this paper, we present an autonomous systems architecture and development framework paired with a persistent distributed modeling and simulation (ModSim) environment for test and evaluation of autonomous systems. They were designed under ATTRACTOR in order to measure and establish trustworthiness and trust in single-and multi-agent human-machine systems whether these machines are fixed-wing general aviation, rotary-wing Unmanned Aerial Vehicles (UAVs), ground rovers, or even spacecraft. The Autonomous Entity Operational Network (AEON) framework enables autonomous system development with an easily extensible collection of libraries and plug-n-play nodes facilitated by the Data Distribution Service (DDS) communication protocol standard. The Baseline Environment for Autonomous Modeling (BEAM) simulation environment is a distributed mixed-reality Unity™-based environment built around the same DDS communication paradigm allowing for easy integration with AEON-based autonomous applications, enabling sim-to-flight with minimal configuration changes. Using AEON and BEAM, source code that runs in simulation ports directly to hardware and has successfully flown in the National Airspace System (NAS) at NASA LaRC many times over the lifetime of ATTRACTOR.

Benjamin N Kelley↗
NASA NTRS1961

Measurements of Aerodynamic Heat Transfer and Boundary-Layer Transition on a 10 deg Cone in Free Flight at Supersonic Mach Numbers up to 5.9

Measurements of aerodynamic heat transfer have been made at six stations on the 40-inch-long 10 deg. total-angle conical nose of a rocket- propelled model which was flight tested at Mach numbers up to 5.9. are presented for a range of local Mach number just outside the bound- ary layer on the cone from 1.57 to 5.50, and a range of local Reynolds number from 6.6 x 10(exp 6) to 55.2 x 10(exp 6) based on length from the nose tip.

Rumsey, Charles B.↗
NASA NTRS1995

Shuttle Laser Altimeter (SLA): A pathfinder for space-based laser altimetry and lidar

The Shuttle Laser Altimeter (SLA) is a Hitchhiker experiment now being integrated for first flight on STS-72 in November 1995. Four Shuttle flights of the SLA are planned at a rate of about a flight every 18 months. They are aimed at the transition of the Goddard Space Flight Center airborne laser altimeter and lidar technology to low Earth orbit as a pathfinder for operational space-based laser remote sensing devices. Future alser altimeter sensors such as the Geoscience Laser Altimeter System (GLAS), an Earth Observing System facility instrument, and the Multi-Beam Laser Altimeter (MBLA), the land and vegetation laser altimeter for the NASA TOPSAT (Topography Satellite) Mission, will utilize systems and approaches being tested with SLA. The SLA Instrument measures the distance from the Space Shuttle to the Earth's surface by timing the two-way propagation of short (approximately 10 na noseconds) laser pulses. laser pulses at 1064 nm wavelength are generated in a laser transmitter and are detected by a telescope equipped with a silicon avalanche photodiode detector. The SLA data system makes the pulse time interval measurement to a precision of about 10 nsec and also records the temporal shape of the laser echo from the Earth's surface for interpretation of surface height distribution within the 100 m diam. sensor footprint. For example, tree height can be determined by measuring the characteristic double-pulse signature that results from a separation in time of laser backscatter from tree canopies and the underlying ground. This is accomplished with a pulse waveform digitizer that samples the detector output with an adjustable resolution of 2 nanoseconds or wider intervals in a 100 sample window centered on the return pulse echo. The digitizer makes the SLA into a high resolution surface lidar sensor. It can also be used for cloud and atmospheric aerosol lidar measurements by lengthening the sampling window and degrading the waveform resolution. Detailed test objectives for the STS-72 mission center on the acquisition of sample data sets for land topography and vegetation height, waveform digitizer performance, and verification of data acquisition algorithms. The operational concept of SLA is illustrated in Fig. 1 where a series of 100 m footprints stretch in a profile of Earth surface topography along the nadir track of the Space Shuttle. The location of SLA as a dual canister payload on the Hitchhiker Bridge Assembly in Bay 12 of the Space Shuttle Endeavor can also be noted in this figure. Full interpretation of the SLA range measurement data set requires a 1 m knowledge of the Orbiter trajectory and better than 0.1 deg knowledge of Orbiter pointing angle. These ancillary data sets will be acquired during the STS-72 mission with an on-board Global Positioning System (GPS) receiver, K-band range and range-rate tracking of the Orbiter through TDRSS, and use of on-board inertial measurement units and star trackers. Integration and interpretation of all these different data sets as a pathfinder investigation for accurate determination of Earth surface elevation is the overall science of the SLA investigation.

Bufton, Jack↗
NASA NTRS2017

Greased Lightning (GL-10) Performance Flight Research: Flight Data Report

Modern aircraft design methods have produced acceptable designs for large conventional aircraft performance. With revolutionary electronic propulsion technologies fueled by the growth in the small UAS (Unmanned Aerial Systems) industry, these same prediction models are being applied to new smaller, and experimental design concepts requiring a VTOL (Vertical Take Off and Landing) capability for ODM (On Demand Mobility). A 50% sub-scale GL-10 flight model was built and tested to demonstrate the transition from hover to forward flight utilizing DEP (Distributed Electric Propulsion)[1][2]. In 2016 plans were put in place to conduct performance flight testing on the 50% sub-scale GL-10 flight model to support a NASA project called DELIVER (Design Environment for Novel Vertical Lift Vehicles). DELIVER was investigating the feasibility of including smaller and more experimental aircraft configurations into a NASA design tool called NDARC (NASA Design and Analysis of Rotorcraft)[3]. This report covers the performance flight data collected during flight testing of the GL-10 50% sub-scale flight model conducted at Beaver Dam Airpark, VA. Overall the flight test data provides great insight into how well our existing conceptual design tools predict the performance of small scale experimental DEP concepts. Low fidelity conceptual design tools estimated the (L/D)( sub max)of the GL-10 50% sub-scale flight model to be 16. Experimentally measured (L/D)( sub max) for the GL-10 50% scale flight model was 7.2. The aerodynamic performance predicted versus measured highlights the complexity of wing and nacelle interactions which is not currently accounted for in existing low fidelity tools.

McSwain, Robert G.↗
NASA NTRS2021

The Causes of Propeller Pitching Moment and the Conditions for its Significance

Recent development of vertical takeoff and landing (VTOL) aircraft has renewed interest in the study of propellers. One metric in particular, the propeller pitching moment, has been observed to be important to VTOL aircraft stability and control in the past. Propellers at angles of attack could not be accurately modeled in generations past due to a lack of computational power, but even with advances in computer technology, modern designers seem to possess insufficient knowledge in this area. In this dissertation, we study the physics behind propeller pitching moment in the context of an isolated propeller and a propeller upstream of a wing. An unsteady 3D vortex lattice method is developed specifically to model propellers at angles of attack and is validated by comparing to high-fidelity CFD analyses. We then use the model to isolate velocity influences to show that the propeller pitching moment is largely caused by two effects: a skewed wake and the presence of wing circulation. Generated maps of propeller pitching moment over a range of operational parameters corresponding to VTOL transition show that the low flight speeds and high angles of attack encountered during transition lead to significant magnitudes of propeller pitching moment that would be difficult to trim using passive methods. Also, derivation of a generalizable metric of significance shows that the peak contribution of propeller pitching moment to aircraft stability is comparable to a longitudinal displacement of the center of gravity by several percent of the wing chord. Finally, we give a concluding discussion on the impact of propeller pitching moment on VTOL aircraft design.

Xiaofan Fei↗
NASA NTRS2021

Transition Analysis for Isolated Trips on BOLT-II Wind-Tunnel and Flight Configuration

The BOLT-II configuration designed for an upcoming flight experiment exemplifies the complexities of hypersonic boundary layer transition in the presence of multiple and potentially interacting instability mechanisms. The present paper is related to the NASA-led roughness experiment on the secondary side of the BOLT-II configuration. First, computations are performed to aid mean-flow based correlations for the transition measurements acquired during an experimental campaign in the Ludwieg Tube facility at the United States Air Force Academy. To that end, both laminar and turbulent flow computations are performed for selected conditions of the experiment with a 1:3 scale model of the slightly shorter BOLT configuration. The variation in well-known correlation parameters for transition due to isolated roughness elements with respect to element position, height, and flow Reynolds number is delineated. Furthermore, the wake instability theory is used to examine the amplification of unstable disturbances behind the centerline trip at the design conditions of the BOLT-II flight experiment and for its dynamically scaled version on the 1:3 scale model of the wind tunnel experiment. To our knowledge, this study represents the first analysis of the wake instabilities in the presence of a prominent entropy layer outside the boundary layer. At the nominal flight design condition of Re ∞ ) = 5.44 and Re ∞ = 2.5 x 10 6 /m, a diamond planform (“pizza-box”) trip with k/δ = 0.70 and planform-halfwidth-to-height ratio of b/k = 3.0 at X/L = 0.254 induces a strong distortion of the boundary-layer flow in the vicinity of the symmetry plane, such that the wake structure includes a centerline streak produced by the flow retardation behind the trip along with multiple additional, prominent vorticity structures representing the necklace vortex system. Stability results reveal that each of these streaks can support a strong amplification of wake instabilities within a frequency band of 95 kHz–255 kHz, with a peak N-factor of greater than 15 beyond X/L ≈ 0.42. The dynamically scaled wind tunnel configuration with Re ∞ = 20.25 x 10 6 /m is also found to support N > 15 at similar axial stations.

BOLT↗
NASA NTRS2021

Transition Analysis for Isolated Trips on BOLT-II Wind-Tunnel and Flight Configuration

The BOLT-II configuration designed for an upcoming flight experiment exemplifies the complexities of hypersonic boundary layer transition in the presence of multiple and potentially interacting instability mechanisms. The present paper is related to the NASA-led roughness experiment on the secondary side of the BOLT-II configuration. First, computations are performed to aid mean-flow based correlations for the transition measurements acquired during an experimental campaign in the Ludwieg Tube facility at the United States Air Force Academy. To that end, both laminar and turbulent flow computations are performed for selected conditions of the experiment with a 1:3 scale model of the slightly shorter BOLT configuration. The variation in well-known correlation parameters for transition due to isolated roughness elements with respect to element position, height, and flow Reynolds number is delineated. Furthermore, the wake instability theory is used to examine the amplification of unstable disturbances behind the centerline trip at the design conditions of the BOLT-II flight experiment and for its dynamically scaled version on the 1:3 scale model of the wind tunnel experiment. To our knowledge, this study represents the first analysis of the wake instabilities in the presence of a prominent entropy layer outside the boundary layer. At the nominal flight design condition of Re ∞ ) = 5.44 and Re ∞ = 2.5 x 10 6 /m, a diamond planform (“pizza-box”) trip with k/δ = 0.70 and planform-halfwidth-to-height ratio of b/k = 3.0 at X/L = 0.254 induces a strong distortion of the boundary-layer flow in the vicinity of the symmetry plane, such that the wake structure includes a centerline streak produced by the flow retardation behind the trip along with multiple additional, prominent vorticity structures representing the necklace vortex system. Stability results reveal that each of these streaks can support a strong amplification of wake instabilities within a frequency band of 95 kHz–255 kHz, with a peak N-factor of greater than 15 beyond X/L ≈ 0.42. The dynamically scaled wind tunnel configuration with Re ∞ = 20.25 x 10 6 /m is also found to support N > 15 at similar axial stations.

BOLT↗
NASA NTRS2010

Experimental Validation of L1 Adaptive Control: Rohrs' Counterexample in Flight

The paper presents new results on the verification and in-flight validation of an L1 adaptive flight control system, and proposes a general methodology for verification and validation of adaptive flight control algorithms. The proposed framework is based on Rohrs counterexample, a benchmark problem presented in the early 80s to show the limitations of adaptive controllers developed at that time. In this paper, the framework is used to evaluate the performance and robustness characteristics of an L1 adaptive control augmentation loop implemented onboard a small unmanned aerial vehicle. Hardware-in-the-loop simulations and flight test results confirm the ability of the L1 adaptive controller to maintain stability and predictable performance of the closed loop adaptive system in the presence of general (artificially injected) unmodeled dynamics. The results demonstrate the advantages of L1 adaptive control as a verifiable robust adaptive control architecture with the potential of reducing flight control design costs and facilitating the transition of adaptive control into advanced flight control systems.

Xargay, Enric↗
NASA NTRS1959

Effects of Nose Radius and Extreme Cooling on Boundary-Layer Transition for Three Smooth 15°-Cone-Cylinders in Free Flight at Mach Numbers to 8.50

Three highly polished 15°- included- angle cone- cylinders with hemispherical tips of several diameters ( 2, 3, and 4 in.) have been flown in order to obtain boundary- layer transition data at very low wall to local stream temperature ratios, and heat- transfer data. All surfaces had a 2-microinch average roughness height. Laminar flow existed over the entire hemispherical nose of the 2- and 3-inch-tip- diameter models throughout the complete flight history. Extreme cooling to wall to local stream temperature ratios at the sonic point as low as 0.20 did not cause transition on the nose for diameters as large as 3 inches. However, extreme cooling did cause early transition on the 4-inch model where it appears probable that transition occurred forward of the 45° station at a wall to local stream temperature ratio of about 0.26. Variations in tip diameter influenced transition downstream of the nose under conditions of extreme cooling. The 2-inch- tip model was laminar at all cone- cylinder stations at temperature ratios as low as 0.32 whereas the 3- and 4-inch-tip models were turbulent at the same local flow conditions but at higher wall to local temperature ratios. Transition on the cone and cylinder of the 3- and 4-inch- tip bodies appeared to be sensitive to local Mach number, and occurred at higher local temperature ratios when values of local Mach number were higher. Increasing the nose diameter from 2 to 3 inches significantly changed the local flow conditions for which laminar flow existed on the cone- cylinder afterbody. However, a further increase in tip size t o a 4-inch diameter had no discernable effect on the local flow conditions at transition. The transition results of the 3- and 4-inch-nose-diameter smooth bodies are similar to those observed on a 7/8-inch-nose-diameter body with roughened surfaces. Turbulent boundary layers resulted in both cases at very low wall to local stream temperature ratios. Both laminar and turbulent heat-transfer data were in good agreement with theoretical Stanton numbers when heat-transfer reduction due to tip blunting was considered.

CYLINDRICAL AFTERBODY↗
NASA NTRS1953

Flight Investigation of the Stability and Control Characteristics of a 0.13-Scale Model of the Convair XFY-1 Vertically Rising Airplane During Constant-Altitude Transitions, TED No. NACA DE 368

An investigation is being conducted to determine the dynamic stability and control characteristics of a 0.13-scale flying model of the Convair XFY-1 vertically rising airplane. This paper presents the results of flight tests to determine the stability and control characteristics of the model during constant-altitude slow transitions from hovering to normal unstalled forward flight. The tests indicated that the airplane can be flown through the transition range fairly easily although some difficulty will probably encountered in controlling the yawing motions at angles of attack between about 60 and 40. An increase in the size of the vertical tail will not materially improve the controllability of the yawing motions in this range of angle of attack but the use of a yaw damper will make the yawing motions easy to control throughout the entire transitional flight range. The tests also indicated that the airplane can probably be flown sideways satisfactorily at speeds up to approximately 33 knots (full scale) with the normal control system and up to approximately 37 knots (full scale) with both elevons and rudders rigged to move differentially for roll control. At sideways speeds above these values, the airplane will have a strong tendency to diverge uncontrollably in roll.

Lovell, Powell M., Jr.↗
NASA NTRS1972

An experimental investigation of turbulent boundary layers at high Mach number and Reynolds numbers

Skin friction, heat transfer and pressure measurements were obtained in laminar, transitional and turbulent boundary layers on flat plates at Mach numbers from 7 to 13 at wall-to-free stream stagnation temperature ratios from 0.1 to 0.3. Measurements in laminar flows were in excellent agreement with the theory of Cheng. Correlations of the transition measurements with measurements on flight vehicles and in ballistic ranges show good agreement. Our transition measurements do not correlate well with those of Pate and Schueler. Comparisons have been made between the skin friction and heat transfer measurements and the theories of Van Driest, Eckert and Spalding and Chi. These comparisons reveal in general that at the high end of our Mach number range (10-13) the theory of Van Driest is in best agreement with the data, whereas at lower Mach numbers (6.5-10) the Spalding Chi theory is in better agreement with the measurements.

Holden, M. S.↗
NASA NTRS1979

Critical considerations for wind-tunnel testing V/STOL aircraft models

Low-speed wind-tunnel testing of V/STOL aircraft concepts to determine the aerodynamic-propulsion interaction effects during the transition between hover and wingborne flight is a necessary step in the development cycle of this type of aircraft. The paper examines factors which must be dealt with to assure that the information obtained in experiments is accurate and representative of the full-scale aircraft modeled. Areas of discussion include: (1) Proper engine simulation selection and model size constraints as a result of the selection; (2) selection of reference power-off condition for determining propulsion interaction effects; (3) modeling of realistic flight conditions to obtain a comprehensive evaluation of the entire transition performance; and (4) wind-tunnel boundary interferences and how these are highly configuration dependent.

Margason, R. J.↗
NASA NTRSDate not supplied

Development Of 12 Kw Hall Thrusters for Nasa Lunar Gateway Power And Propulsion Element

NASA is embarking on a new and exciting era of human exploration to the Moon and its vicinity. As part of the Artemis program, NASA is developing the lunar Gateway, an orbiting platform in Near Rectilinear Halo Orbit (NRHO) about the Moon. The first two elements of the Gateway will be launched in 2024 and will be transferred from a high Earth orbit to the NRHO via the use of Solar Electric Propulsion (SEP). The SEP system is located on the Power and Propulsion Element (PPE) which will provide up to 60 kW of power. Aerojet Rocketdyne is developing the 12 kW flight Hall thrusters to be used for transferring the PPE and the Habitat and Logistics Outpost (HALO) module to NRHO. Work is continuing on the development testing, and these results will be described in the paper. The project has also recently completed its critical design review and is transitioning to the fabrication of the three flight thrusters. The 12 kW Hall thrusters are being developed under the NASA Advanced Electric Propulsion System (AEPS) program. As part of the AEPS program, AR built two Engineering Test Unit (ETU) Hall thrusters based on the NASA HERMeS engine and conducted a series of tests to validate the design. One series of tests focused on environments and functional testing, while the other series was mainly focused on long duration test blocks. Results from these tests were used to compare with NASA data from the HERMeS thruster. The comparison of the test results showed no change to the critical performance and lifetime parameters, which enabled the next phase of the program to proceed. Currently testing is continuing on the Engineering Development Units (EDU) as part of the flight qualification activities. The successful completion of the CDR serves as the starting point for the flight thruster fabrication, which is now underway to support the launch of the Gateway modules in 2024. The development and qualification of the AEPS 12 kW Hall thrusters is proceeding well. As the program completes CDR and transitions into flight builds of the three 12 kW Hall thrusters that will be used to transfer the combined PPE and HALO stack to the NRHO, the results of the development testing are reviewed in this presentation, and a status of the program and future plans is provided. The launch of the two Gateway modules and the transfer of this large payload to cislunar orbit will mark a significant milestone in electric propulsion, as it will demonstrate the ability of SEP to transfer very large payloads over great distances. This establishes the precedent that could lead to cargo transfers from the Earth to the Moon or even to Mars using SEP.

Hall thrusters↗
NASA NTRS1996

Comparison of Aero/Propulsion Transition Characteristics for a Joint Strike Fighter Configuration

NASA Ames conducted a series tests of a large-scale powered model of Lockheed Martin Skunk Works' JSF STOVL configuration at the 80- by 120-Foot Wind Tunnel. The model uses a modified version of an F-16 fighter engine (a Pratt & Whitney F100-229 engine). To provide vertical flight capability, the Lockheed aircraft incorporates a forward fuselage mounted vertical lift fan in addition to an aft mounted vectoring nozzle all driven by a single engine. The lift fan is driven off the engine by means of a shaft and gear system. The data presented is for STOVL configuration 140, a wing-body-canard planform. The main goal of this testing was to obtain propulsion induced data for evaluating differences between small- and large-scale model testing during the transition flight regime between jet- and wing-borne flight. The data presented is from aerodynamic testing of the model in both the unpowered (engine-off) and powered (engine running) configurations. This data, when combined with the propulsion system thrust calibration data from the NASA Ames' Outdoor Aerodynamic Research Facility (OARF), is used to determine the propulsion induced effects during transition.

Naumowicz, Tim↗