SEARCH · Search NASA

Results for “Upper bounds”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

All sources NASA NTRS DOE OSTI

NASA NTRS1995

The Deep Space Network stability analyzer

A stability analyzer for testing NASA Deep Space Network installations during flight radio science experiments is described. The stability analyzer provides realtime measurements of signal properties of general experimental interest: power, phase, and amplitude spectra; Allan deviation; and time series of amplitude, phase shift, and differential phase shift. Input ports are provided for up to four 100 MHz frequency standards and eight baseband analog (greater than 100 kHz bandwidth) signals. Test results indicate the following upper bounds to noise floors when operating on 100 MHz signals: -145 dBc/Hz for phase noise spectrum further than 200 Hz from carrier, 2.5 x 10(exp -15) (tau =1 second) and 1.5 x 10(exp -17) (tau =1000 seconds) for Allan deviation, and 1 x 10(exp -4) degrees for 1-second averages of phase deviation. Four copies of the stability analyzer have been produced, plus one transportable unit for use at non-NASA observatories.

Breidenthal, Julian C.↗

NASA NTRS1994

Constraints on hydrothermal heat flux through the oceanic lithosphere from global heat flow

A significant discrepancy exists between the heat flow measured at the seafloor and the higher values predicted by thermal models of the cooling lithosphere. This discrepancy is generally interpreted as indicating that the upper oceanic crust is cooled significantly by hydrothermal circulation. The magnitude of this heat flow discrepancy is the primary datum used to estimate the volume of hydrothermal flow, and the variation in the discrepancy with lithospheric age is the primary constraint on how the hydrothermal flux is divided between near-ridge and off-ridge environments. The resulting estimates are important for investigation of both the thermal structure of the lithosphere and the chemistry of the oceans. We reevaluate the magnitude and age variation of the discrepancy using a global heat flow data set substantially larger than in earlier studies, and the GDHI (Global Depth and Heat Flow) model that better predicts the heat flow. We estimate that of the predicted global oceanic heat flux of 32 x 10(exp 12) W, 34% (11 x 10(exp 12) W) occurs by hydrothermal flow. Approximately 30% of the hydrothermal heat flux occurs in crust younger than 1 Ma, so the majority of this flux is off-ridge. These hydrothermal heat flux estimates are upper bounds, because heat flow measurements require sediment at the site and so are made preferentially at topographic lows, where heat flow may be depressed. Because the water temperature for the near-ridge flow exceeds that for the off-ridge flow, the near-ridge water flow will be even a smaller fraction of the total water flow. As a result, in estimating fluxes from geochemical data, use of the high water temperatures appropriate for the ridge axis may significantly overestimate the heat flux for an assumed water flux or underestimate the water flux for an assumed heat flux. Our data also permit improved estimates of the 'sealing' age, defined as the age where the observed heat flow approximately equals that predicted, suggesting that hydrothermal heat transfer has largely ceased. Although earlier studies suggested major differences in sealing ages for different ocean basins, we find that the sealing ages for the Atlantic, Pacific, and Indian oceans are similar and consistent with the sealing age for the entire data set, 65 +/- 10 Ma. The previous inference of a young (approximately 20 Ma) sealing age for the Pacific appears to have biased downward several previous estimates of the global hydrothermal flux. The heat flow data also provide indirect evidence for the mechanism by which the hydrothermal heat flux becomes small, which has often been ascribed to isolation of the igneous crust from seawater due to the hydraulic conductivity of the intervening sediment. We find, however, that even the least sedimented sites show the systematic increase of the ratio of observed to predicted heat flow with age, although the more sedimented sites have a younger sealing age. Moreover, the heat flow discrepancy persists at heavily sedimented sites until approximately 50 Ma. It thus appears that approximately 100-200 m of sediment is neither necessary nor sufficient to stop hydrothermal heat transfer. We therefore conclude that the age of the crust is the primary control on the fraction of heat transported by hydrothermal flow and that sediment thickness has a lesser effect. This inference is consistent with models in which hydrothermal flow decreases with age due to reduced crustal porosity and hence permeability.

Stein, Carol A.↗

NASA NTRS1994

Derivation and experimental verification of clock synchronization theory

The objective of this work is to validate mathematically derived clock synchronization theories and their associated algorithms through experiment. Two theories are considered, the Interactive Convergence Clock Synchronization Algorithm and the Mid-Point Algorithm. Special clock circuitry was designed and built so that several operating conditions and failure modes (including malicious failures) could be tested. Both theories are shown to predict conservative upper bounds (i.e., measured values of clock skew were always less than the theory prediction). Insight gained during experimentation led to alternative derivations of the theories. These new theories accurately predict the clock system's behavior. It is found that a 100% penalty is paid to tolerate worst case failures. It is also shown that under optimal conditions (with minimum error and no failures) the clock skew can be as much as 3 clock ticks. Clock skew grows to 6 clock ticks when failures are present. Finally, it is concluded that one cannot rely solely on test procedures or theoretical analysis to predict worst case conditions. conditions.

INTERACTIVE CONVERGENCE CLOCK↗

NASA NTRS1994

Toward a theory of interstellar turbulence. 1: Weak Alfvenic turbulence

We study weak Alfvenic turbulence of an incompressible, magnetized fluid in some detail, with a view to developing a firm theoretical basis for the dynamics of small-scale turbulence in the interstellar medium. We prove that resonant 3-wave interactions are absent. We also show that the Iroshnikov-Kraichnan theory of incompressible, magnetohydrodynamic turbulence -- which is widely accepted -- describes weak 3-wave turbulence; consequently, it is incorrect. Physical arguments, as well as detailed calculations of the coupling coefficients are used to demonstrate that these interactions are empty. We then examine resonant 4-wave interactions, and show that the resonance relations forbid energy transport to small spatial scales along the direction of the mean magnetic field, for both the shear Alfven wave and the pseudo Alfven wave. The three-dimensional inertial-range energy spectrum of 4-wave shear Alfven turbulence guessed from physical arguments reads E(k(sub z), k(sub perpendicular)) approximately V(sub A)v(sub L)L(exp -1/3)k(sub perpendicular)(exp -10/3), where V(sub A) is the Alfven speed, and v(sub L) is the velocity difference across the outer scale L. Given this spectrum, the velocity difference across lambda(sub perpendicular) approximately k(sub perpendicular exp -1) is v(sub lambda (sub perpendicular)) is approximately v(sub L)(lambda(sub perpendicular)/L)(exp 2/3). We derive a kinetic equation, and prove that this energy spectrum is a stationary solution and that it implies a positive flux of energy in k-space, along directions perpendicular to the mean magnetic field. Using this energy spectrum, we deduce that 4-wave interactions strengthen as the energy cascades to small, perpendicular spatial scales; beyond an upper bound in perpendicular wavenumber, k(sub perpendicular)L is approximately (V(sub A)/v(sub L))(exp 3/2), weak turbulence theory ceases to be valid. Energy excitation amplitudes must be very small for the 4-wave inertial-range to be substantial. When the excitation is strong, the width of the 4-wave inertial-range shrinks to zero. This seems likely to be the case in the interstellar medium.

Sridhar, S.↗

NASA NTRS1994

The determination of the mass and mean density of Enceladus from its observed shape

Application of limb-fitting methods to the 11 best Voyager 2 images of Enceladus has shown that the shape of this satellite is closely represented by a triaxial ellipsoid. The observed ratio of the differences of the principal axes F = (b - c)/(a - c) is 0.23 (sup +0.04 sub - 0.01), consisting with the value F = 0.23 expected for a synchronously rotating satellite in hydrostatic equilibrium. We also deduce from the Voyager observations, after allowing for limb topography, that the mean radius of the satellite is 249.4 +/- 0.2 km. For satellites of known mass, measurement of the size and shape leads to a determination of the satellite's mean density and moment of inertial. We have used this method to determine the moments of inertia of Mimas (1988) and Tethys (1991). Enceladus appears to be hydrostatically relaxed, making it an ideal candidate for this type of analysis. However, none of the Pioneer or Voyager spacecraft had a close encounter with this satellite and thus its mass is effectively unknown. Enceladus is trapped in a 2:1 orbit-orbit resonance with Dione, but the amplitudes of libration are too small to allow a useful mass determination. Using the observed shape alone, without any other assumptions other than that the satellite is in hydrostatic equilibrium at its present orbital radius, we place an upper bound on the mean density of 1.12 +/- 0.05 g/cu cm. Thus, the mean density of Enceladus is probably little more than that of water-ice and we conclude that this satellite is markedly deficient in rock. If the mass of a satellite is unknown, but the satellite is differentiated and has a deep mantle of known composition, then we show that measurement of the shape alone can lead to a determination of the satellite's mass, mean density, and moment of inertia. Application of this method to Enceladus, assuming that the satellite has a deep mantle of water-ice of density 0.93 g/cu cm, gives the result that the mean density of the satellite is 1.00 +/- 0.03 g/cu cm. This result fills the one remaining gap in our knowledge of the structure of the Saturnian satellite system. We now know the mean densities of all the primary Saturnian satellites in the sequence from the coorbital satellites, Janus and Epimetheus, through to the outer satellite Iapetus (the densities of the small, secondary satellites in Trojan-type orbits are still unknown). The Saturnian system possesses two striking features. (1) Because of significant porosity, the mean material densities of the satellites Janus, Epimetheus, and Mimas could be substantially greater than the apparent mean densities of these satellies. (2) The densities of the satellites are not correlated with their distances from the planet; in particular, the satellites Enceladus and Tethys have lower mean densities than their interior and exterior neighbors, Mimas and Dione. This may be the result of gross postformation redistribution of rock and ice, possibly due to satellite disruptions are suggested by Smith et al. (1982).

Dermott, Stanley F.↗

NASA NTRS1994

The whistler heat flux instability: Threshold conditions in the solar wind

Solar wind electrons are observed often to consist of two components: a core and a halo. The anisotropics and relative average speeds of these components correspond to a heat flux that has the potential to excite several different electromagetic instabilities; wave-particle scattering by the resulting enhanced fluctuations can limit this heat flux. This manuscript describes theoretical studies using the linear Vlasco dispersion equation for drifting bi-Maxwellian component distributions in a homogeneous plasma to examine the threshold of the whistler heat flux instability. Expressions for this threshold are obtained from two different parametric baselines: a local model that yields scalings as functions of local dimensionless plasma paramaters, and a global model based on average electron properties observed during the in-eliptic phase of the Ulysses mission. The latter model yields an expression for the heat flux at threshold of the whistler instability as a function of helisopheric radius that scales in the same way as the average heat flux observed form Ulysses and that provides an approximate upper bound for that same quantity. This theoretical scaling is combined with the observational results to yield a semi-empirical closure relation for the average electron heat flux in the solar wind between 1 and 5 AU.

Gary, S. Peter↗

NASA NTRS1994

Regulation of the solar wind electron heat fluxfrom 1 to 5 AU: Ulysses observations

In this study we use observations from the three-dimensional electron spectrometer and magnetometer aboard the Ulysses spacecraft to examine the solar wind electron heat flux from 1.2 to 5.4 AU in the ecliptic plane. Throughout Ulusses' transit to 5.4 AU, the electron heat flux decreases more rapidly (approximately R(exp -30)) than simple collisionless expansion along the local magnetic field and is smaller than expected for a thermal gradient heat flux, q(sub parallel e) (r) = - Kappa(sub parallel) del(sub parallel) T(sub e)(r). The radial gradients and magnitudes expected for a number of electron heat flux regulatory mechanisms are examined and compared to the observations. The best agreement is found for heat flux regulation by the whistler heat flux instability. The upper bound and radial scaling for the electron heat flux predicted for the whistler heat flux instability are consistent with the observations.

Scime, Earl E.↗

NASA NTRS1993

The effect of high lift to drag ratio on aerobraking

This work reviews the use of aerodynamic forces to modify the velocity, and therefore, the orbital path of vehicles due to transit through planetary atmospheres, especially when high values of lift can be generated. The concepts of aerobraking and aerocapture are examined, and the limiting factors are discussed. The use of high L/D vehicles, such as hypersonic waveriders, is examined, and the advantages and disadvantages of their use for aerocapture are addressed. This preliminary study of non-optimized aerocapture trajectories suggests that entrance velocities at Mars can be 10 - 12 km/sec for a waverider while sustaining acceptable loads of about 3 - 4 Earth G's over a 3 minute period, diminishing to less than 1 G in about 15 minutes. The entrance velocities are greater than those for a more conventional biconic configuration with similar deceleration loads sustained. The convective heating rate on the waverider, increased due to the higher velocities and sharp leading edges, has an estimated upper bound of 14000 W/sq cm and a corresponding temperature of about 7500 degrees K.

Crouse, Patrick↗

NASA NTRS1996

Good trellises for IC implementation of viterbi decoders for linear block codes

This paper investigates trellis structures of linear block codes for the IC (integrated circuit) implementation of Viterbi decoders capable of achieving high decoding speed while satisfying a constraint on the structural complexity of the trellis in terms of the maximum number of states at any particular depth. Only uniform sectionalizations of the code trellis diagram are considered. An upper bound on the number of parallel and structurally identical (or isomorphic) subtrellises in a proper trellis for a code without exceeding the maximum state complexity of the minimal trellis of the code is first derived. Parallel structures of trellises with various section lengths for binary BCH and Reed-Muller (RM) codes of lengths 32 and 64 are analyzed. Next, the complexity of IC implementation of a Viterbi decoder based on an L-section trellis diagram for a code is investigated. A structural property of a Viterbi decoder called ACS-connectivity which is related to state connectivity is introduced. This parameter affects the complexity of wire-routing (interconnections within the IC). The effect of five parameters namely: (1) effective computational complexity; (2) complexity of the ACS-circuit; (3) traceback complexity; (4) ACS-connectivity; and (5) branch complexity of a trellis diagram on the VLSI complexity of a Viterbi decoder is investigated. It is shown that an IC implementation of a Viterbi decoder based on a non-minimal trellis requires less area and is capable of operation at higher speed than one based on the minimal trellis when the commonly used ACS-array architecture is considered.

Moorthy, H. T.↗

NASA NTRS1996

Good trellises for IC implementation of viterbi decoders for linear block codes

Lin, Shu↗

NASA NTRS1996

Soft-decision decoding techniques for linear block codes and their error performance analysis

The first paper presents a new minimum-weight trellis-based soft-decision iterative decoding algorithm for binary linear block codes. The second paper derives an upper bound on the probability of block error for multilevel concatenated codes (MLCC). The bound evaluates difference in performance for different decompositions of some codes. The third paper investigates the bit error probability code for maximum likelihood decoding of binary linear codes. The fourth and final paper included in this report is concerns itself with the construction of multilevel concatenated block modulation codes using a multilevel concatenation scheme for the frequency non-selective Rayleigh fading channel.

Lin, Shu↗

NASA NTRS1993

Dynamic of Langmuir and Ion-Sound Waves in Type 3 Solar Radio Sources

The evolution of Langmuir and ion-sound waves in type 3 sources is investigated, incorporating linear growth, linear damping, and nonlinear electrostatic decay. Improved estimates are obtained for the wavenumber range of growing waves and the nonlinear coupling coefficient for the decay process. The resulting prediction for the electrostatic decay threshold is consistent with the observed high-field cutoff in the Langmuir field distribution. It is shown that the conditions in the solar wind do not allow a steady state to be attained; rather, bursty linear and nonlinear interactions take place, consistent with the highly inhomogeneous and impulsive waves actually observed. Nonlinear growth is found to be fast enough to saturate the growth of the parent Langmuir waves in the available interaction time. The resulting levels of product Langmuir and ion-sound waves are estimated theoretically and shown to be consistent with in situ ISEE 3 observations of type 3 events at 1 AU. Nonlinear interactions slave the growth and decay of product sound waves to that of the product Langmuir waves. The resulting probability distribution of ion-sound field strengths is predicted to have a flat tail extending to a high-field cutoff. This prediction is consistent with statistics derived here from ISEE 3 observations. Agreement is also found between the frequencies of the observed waves and predictions for the product S waves. The competing processes of nonlinear wave collapse and quasilinear relaxation are discussed, and it is concluded that neither is responsible for the saturation of Langmuir growth. When wave and beam inhomogeneities are accounted for, arguments from quasi-linear relaxation yield an upper bound on the Langmuir fields that is too high to be relevant. Nor are the criteria for direct wave collapse of the beam-driven waves met, consistent with earlier simulation results that imply that this process is not responsible for saturation of the beam instability. Indeed, even if the highest observed Langmuir fields are assumed to he part of a long-wavelength 'condensate' produced via electrostatic decay, they still fall short of the relevant requirements for wave collapse. The most stringent requirement for collapse is that collapsing wave packets not be disrupted by ambient density fluctuations in the solar wind. Fields of several mV m(exp -1) extending over several hundred km would be needed to satisfy this requirement; at 1 AU such fields are rare at best.

Robinson, P. A.↗

NASA NTRS1996

The Mass of Large Impactors

By means of a simplified dynamical model, we have computed the eccentricity change in the orbit of each giant planet, caused by a single, large impact at the end of the accretion process. In order to set an upper bound on this eccentricity change, we have considered the giant planets' present eccentricities as primordial ones. By means of this procedure, we were able to obtain an implicit relation for the impactor masses and maximum velocities. We have estimated by this method the maximum allowed mass to impact Jupiter to be approx. 1.136 x 10(exp -1), being in the case of Neptune approx. 3.99 x 10(exp -2) (expressed in units of each planet final mass). Due to the similar present eccentricities of Saturn, Uranus and Jupiter, the constraint masses and velocities of the bodies to impact them (in units of each planet final mass and velocity respectively) are almost the same for the three planets. These results are in good agreement with those obtained by Lissauer and Safronov. These bounds might be used to derive the mass distribution of planetesimals in the early solar system.

Parisi, M. G.↗

NASA NTRS1997

Good Trellises for IC Implementation of Viterbi Decoders for Linear Block Codes

This paper investigates trellis structures of linear block codes for the integrated circuit (IC) implementation of Viterbi decoders capable of achieving high decoding speed while satisfying a constraint on the structural complexity of the trellis in terms of the maximum number of states at any particular depth. Only uniform sectionalizations of the code trellis diagram are considered. An upper-bound on the number of parallel and structurally identical (or isomorphic) subtrellises in a proper trellis for a code without exceeding the maximum state complexity of the minimal trellis of the code is first derived. Parallel structures of trellises with various section lengths for binary BCH and Reed-Muller (RM) codes of lengths 32 and 64 are analyzed. Next, the complexity of IC implementation of a Viterbi decoder based on an L-section trellis diagram for a code is investigated. A structural property of a Viterbi decoder called add-compare-select (ACS)-connectivity which is related to state connectivity is introduced. This parameter affects the complexity of wire-routing (interconnections within the IC). The effect of five parameters namely: (1) effective computational complexity; (2) complexity of the ACS-circuit; (3) traceback complexity; (4) ACS-connectivity; and (5) branch complexity of a trellis diagram on the very large scale integration (VISI) complexity of a Viterbi decoder is investigated. It is shown that an IC implementation of a Viterbi decoder based on a nonminimal trellis requires less area and is capable of operation at higher speed than one based on the minimal trellis when the commonly used ACS-array architecture is considered.

Moorthy, Hari T.↗

NASA NTRS1996

An Atmospheric Tape Recorder: The Imprint of Tropical Tropopause Temperatures on Stratospheric Water Vapor

We describe observations of tropical stratospheric water vapor q that show clear evidence of large-scale upward advection of the signal from annual fluctuations in the effective 'entry mixing ratio' q(sub E) of air entering the tropical stratosphere. In other words, air is 'marked,' on emergence above the highest cloud tops, like a signal recorded on an upward moving magnetic tape. We define q(sub E) as the mean water vapor mixing ratio, at the tropical tropopause, of air that will subsequently rise and enter the stratospheric 'overworld' at about 400 K. The observations show a systematic phase lag, increasing with altitude, between the annual cycle in q(sub E) and the annual cycle in q at higher altitudes. The observed phase lag agrees with the phase lag calculated assuming advection by the transformed Eulerian-mean vertical velocity of a q(sub E) crudely estimated from 100-hPa temperatures, which we use as a convenient proxy for tropopause temperatures. The phase agreement confirms the overall robustness of the calculation and strongly supports the tape recorder hypothesis. Establishing a quantitative link between q(sub E) and observed tropopause temperatures, however, proves difficult because the process of marking the tape depends subtly on both small- and large-scale processes. The tape speed, or large-scale upward advection speed, has a substantial annual variation and a smaller variation due to the quasi-biennial oscillation, which delays or accelerates the arrival of the signal by a month or two in the middle stratosphere. As the tape moves upward, the signal is attenuated with an e-folding time of about 7 to 9 months between 100 and 50 hPa and about 15 to 18 months between 50 and 20 hPa, constraining possible orders of magnitude both of vertical diffusion K(sub z) and of rates of mixing in from the extratropics. For instance, if there were no mixing in, then K(sub z) would be in the range 0.03-0.09 m(exp 2)/s; this is an upper bound on K(sub z).

Mote, Philip W.↗

NASA NTRS1997

Current Collection in a Magnetic Field

It is found that the upper-bound limit for current collection in the case of strong magnetic field from the current is close to that given by the Parker-Murphy formula. This conclusion is consistent with the results obtained in laboratory experiments. This limit weakly depends on the shape of the wire. The adiabatic limit in this case will be easily surpassed due to strong magnetic field gradients near the separatrix. The calculations can be done using the kinetic equation in the drift approximation. Analytical results are obtained for the region where the Earth's magnetic field is dominant. The current collection can be calculated (neglecting scattering) using a particle simulation code. Dr. Singh has agreed to collaborate, allowing the use of his particle code. The code can be adapted for the case when the current magnetic field is strong. The needed dm for these modifications is 3-4 months. The analytical description and essential part of the program is prepared for the calculation of the current in the region where the adiabatic description can be used. This was completed with the collaboration of Drs. Khazanov and Liemohn. A scheme of measuring the end body position is also proposed. The scheme was discussed in the laboratory (with Dr. Stone) and it was concluded that it can be proposed for engineering analysis.

Krivorutsky, E. N.↗

NASA NTRS1997

Algorithms for Multiple Fault Diagnosis With Unreliable Tests

In this paper, we consider the problem of constructing optimal and near-optimal multiple fault diagnosis (MFD) in bipartite systems with unreliable (imperfect) tests. It is known that exact computation of conditional probabilities for multiple fault diagnosis is NP-hard. The novel feature of our diagnostic algorithms is the use of Lagrangian relaxation and subgradient optimization methods to provide: (1) near optimal solutions for the MFD problem, and (2) upper bounds for an optimal branch-and-bound algorithm. The proposed method is illustrated using several examples. Computational results indicate that: (1) our algorithm has superior computational performance to the existing algorithms (approximately three orders of magnitude improvement), (2) the near optimal algorithm generates the most likely candidates with a very high accuracy, and (3) our algorithm can find the most likely candidates in systems with as many as 1000 faults.

Shakeri, Mojdeh↗

NASA NTRS1998

Thermal State-of-Charge in Solar Heat Receivers

A theoretical framework is developed to determine the so-called thermal state-of-charge (SOC) in solar heat receivers employing encapsulated phase change materials (PCMS) that undergo cyclic melting and freezing. The present problem is relevant to space solar dynamic power systems that would typically operate in low-Earth-orbit (LEO). The solar heat receiver is integrated into a closed-cycle Brayton engine that produces electric power during sunlight and eclipse periods of the orbit cycle. The concepts of available power and virtual source temperature, both on a finite-time basis, are used as the basis for determining the SOC. Analytic expressions for the available power crossing the aperture plane of the receiver, available power stored in the receiver, and available power delivered to the working fluid are derived, all of which are related to the SOC through measurable parameters. Lower and upper bounds on the SOC are proposed in order to delineate absolute limiting cases for a range of input parameters (orbital, geometric, etc.). SOC characterization is also performed in the subcooled, two-phase, and superheat regimes. Finally, a previously-developed physical and numerical model of the solar heat receiver component of NASA Lewis Research Center's Ground Test Demonstration (GTD) system is used in order to predict the SOC as a function of measurable parameters.

Hall, Carsie A., Jr.↗