Search NASA⌕ Search

SEARCH · Search NASA

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Transonic wind tunnel wall interference corrections for three-dimensional models

A procedure for the evaluation of wall interference corrections for three-dimensional models is presented. The Mach number and angle-of-attack corrections require the numerical solution of the potential equation about a simplified representation of the experimental model. Pressure measurements are required near the wind tunnel walls. The correction procedure also requires knowledge of the free-stream Mach number, the model angle of attack, and the lift force experienced by the model. The procedure provides an estimate of the accuracy of the correction. For slender configurations at Mach numbers close to one, the Equivalence Rule formulation is adopted to calculate the wall interference effects. Preliminary results are presented for both general and slender-body configurations.

Rizk, M. H.↗

A likelihood ratio anomaly detector for identifying within-perimeter computer network attacks

The rapid detection of attackers within firewalls of enterprise computer networks is of paramount importance. Anomaly detectors address this problem by quantifying deviations from baseline statistical models of normal network behavior and signaling an intrusion when the observed data deviates significantly from the baseline model. But, many anomaly detectors do not take into account plausible attacker behavior. As a result, anomaly detectors are prone to a large number of false positives due to unusual but benign activity. Our paper first introduces a stochastic model of attacker behavior which is motivated by real world attacker traversal. Then, we develop a likelihood ratio detector that compares the probability of observed network behavior under normal conditions against the case when an attacker has possibly compromised a subset of hosts within the network. Since the likelihood ratio detector requires integrating over the time each host becomes compromised, we illustrate how to use Monte Carlo methods to compute the requisite integral. We then present Receiver Operating Characteristic (ROC) curves for various network parameterizations that show for any rate of true positives, the rate of false positives for the likelihood ratio detector is no higher than that of a simple anomaly detector and is often lower. Finally, we demonstrate the superiority of the proposed likelihood ratio detector when the network topologies and parameterizations are extracted from real-world networks.

97 MATHEMATICS AND COMPUTING↗

Wind-Tunnel Investigation of Paraglider Models at Supersonic Speeds

An investigation was made in the Langley Unitary Plan wind tunnel to determine the behavior of paraglider models at moderate to high supersonic speeds. The models were deployed from a sting in the supersonic stream and steady-state aerodynamic performance data were obtained. Maximum values of the lift-drag ratio were about 1.4 at a Mach number of 2.65 and about 1.2 at a Mach number of 4.65. The angles of attack over which the models could be flown were limited by unsteady behavior of the canopy.

Taylor, Robert T.↗

A mathematical model of a single main rotor helicopter for piloted simulation

A mathematical model, suitable for piloted simulation of the flying qualities of helicopters, is a nonlinear, total force and moment model of a single main rotor helicopter. The model has ten degrees of freedom: six rigid body, three rotor flapping, and the rotor rotational degrees of freedom. The rotor model assumes rigid blades with rotor forces and moments radially integrated and summed about the azimuth. The fuselage aerodynamic model uses a detailed representation over a nominal angle of attack and sideslip range of + or - 15 deg., as well as a simplified curve fit at large angles of attack or sideslip. Stabilizing surface aerodynamics are modeled with a lift curve slope between stall limits and a general curve fit for large angles of attack. A generalized stability and control augmentation system is described. Additional computer subroutines provide options for a simplified engine/governor model, atmospheric turbulence, and a linearized six degree of freedom dynamic model for stability and control analysis.

Talbot, P. D.↗

High angle-of-attack aerodynamic characteristics of crescent and elliptic wings

Static longitudinal and lateral-directional forces and moments were measured for elliptic- and crescent-wing models at high angles-of-attack in the NASA Langley 14 by 22-Ft Subsonic Tunnel. The forces and moments were obtained for an angle-of-attack range including stall and post-stall conditions at a Reynolds number based on the average wing chord of about 1.8 million. Flow-visualization photographs using a mixture of oil and titanium-dioxide were also taken for several incidence angles. The force and moment data and the flow-visualization results indicated that the crescent wing model with its highly swept tips produced much better high angle-of-attack aerodynamic characteristics than the elliptic model. Leading-edge separation-induced vortex flow over the highly swept tips of the crescent wing is thought to produce this improved behavior at high angles-of-attack. The unique planform design could result in safer and more efficient low-speed airplanes.

Vandam, C. P.↗

Wind Tunnel Testing of Various Disk-Gap-Band Parachutes

Two Disk-Gap-Band model parachute designs were tested in the NASA Langley Transonic Dynamics Tunnel. The purposes of these tests were to determine the drag and static stability coefficients of these two model parachutes at various subsonic Mach numbers in support of the Mars Exploration Rover mission. The two model parachute designs were designated 1.6 Viking and MPF. These model parachute designs were chosen to investigate the tradeoff between drag and static stability. Each of the parachute designs was tested with models fabricated from MIL-C-7020 Type III or F-111 fabric. The reason for testing model parachutes fabricated with different fabrics was to evaluate the effect of fabric permeability on the drag and static stability coefficients. Several improvements over the Viking-era wind tunnel tests were implemented in the testing procedures and data analyses. Among these improvements were corrections for test fixture drag interference and blockage effects, and use of an improved test fixture for measuring static stability coefficients. The 1.6 Viking model parachutes had drag coefficients from 0.440 to 0.539, while the MPF model parachutes had drag coefficients from 0.363 to 0.428. The 1.6 Viking model parachutes had drag coefficients 18 to 22 percent higher than the MPF model parachute for equivalent fabric materials and test conditions. Model parachutes of the same design tested at the same conditions had drag coefficients approximately 11 to 15 percent higher when manufactured from F-111 fabric as compared to those fabricated from MIL-C-7020 Type III fabric. The lower fabric permeability of the F-111 fabric was the source of this difference. The MPF model parachutes had smaller absolute statically stable trim angles of attack as compared to the 1.6 Viking model parachutes for equivalent fabric materials and test conditions. This was attributed to the MPF model parachutes larger band height to nominal diameter ratio. For both designs, model parachutes fabricated from F-111 fabric had significantly greater statically stable absolute trim angles of attack at equivalent test conditions as compared to those fabricated from MILC-7020 Type III fabric. This reduction in static stability exhibited by model parachutes fabricated from F-111 fabric was attributed to the lower permeability of the F-111 fabric. The drag and static stability coefficient results were interpolated to obtain their values at Mars flight conditions using total porosity as the interpolating parameter.

Cruz, Juan R.↗

Subsonic stability and control derivatives for an unpowered, remotely piloted 3/8-scale F-15 airplane model obtained from flight test

In response to the interest in airplane configuration characteristics at high angles of attack, an unpowered remotely piloted 3/8-scale F-15 airplane model was flight tested. The subsonic stability and control characteristics of this airplane model over an angle of attack range of -20 to 53 deg are documented. The remotely piloted technique for obtaining flight test data was found to provide adequate stability and control derivatives. The remotely piloted technique provided an opportunity to test the aircraft mathematical model in an angle of attack regime not previously examined in flight test. The variation of most of the derivative estimates with angle of attack was found to be consistent, particularly when the data were supplemented by uncertainty levels.

Iliff, K. W.↗

Model mount system for testing flutter

A wind tunnel model mount system is disclosed for effectively and accurately determining the effects of attack and airstream velocity on a model airfoil or aircraft. The model mount system includes a rigid model attached to a splitter plate which is supported away from the wind tunnel wall several of flexible rods. Conventional instrumentation is employed to effect model rotation through a turntable and to record model flutter data as a function of the angle of attack versus dynamic pressure.

Farmer, M. G.↗

Space Shuttle Orbiter Crew Hatch Jettison Test using a 0.0405-scale model (16-0) in the Texas A/M low speed wind tunnel (OA362). Space Shuttle aerothermodynamic data report

This report contains post-test information for the Space Shuttle Orbiter Crew Hatch Jettison Test OA362 which was conducted in the Texas A&M Low Speed Wind Tunnel from 6/15/87 to 6/22/87. The test objective was to verify that the crew hatch, once jettisoned, would clear the orbiter under various simulated flight conditions. Several model hatches were used with the 0.0405-scale orbiter (Model 16-0). The model's angle of attack was set at 10, 15, and 20 degrees while the sideslip had values of minus 5, 0, and plus 5 degrees. The full scale Qbars that were simulated were 105, 128, 160, and 210 psf. In the hatch jettison mechanism itself, the plunger pressure was varied to achieve horizontal velocities of 3, 5, 7, and 20.1 feet per second model scale, and the plunger location was varied to achieve a variety of rotational velocities. The orbiter model was subjected to 122 runs with 13 different hatches. Of these, 60 were good runs.

Mitchell, C. E.↗

Wind-Tunnel Investigation of a Small-Scale Model of an Aerial Vehicle Supported by Tilting Ducted Fans

A wind-tunnel investigation has been made to study the static longitudinal and lateral stability characteristics of a simplified aerial vehicle supported by ducted fans that tilt relative to the airframe. The ducts were in a triangular arrangement with one duct in front and two at the rear in order to minimize the influence of the downwash of the front duct on the rear ducts. The results of the investigation were compared with those of a similar investigation for a tandem two-duct arrangement in which the ducts were fixed (rather than tiltable) relative to the airframe, since the three-duct configuration had been devised in an attempt to avoid some of the deficiencies of the tandem fixed-duct configuration. The results of the investigation indicated that the tilting-duct arrangement had less noseup pitching moment for a given forward speed than the tandem fixed-duct arrangement. The model had less angle-of-attack instability than the tandem fixed-duct arrangement. The model was directionally unstable but had a positive dihedral effect throughout the test speed range.

Smith, Charles C., Jr.↗

Aerodynamic Testing of the Orion Launch Abort Tower Separation with Jettison Motor Jet Interactions

The aerodynamic database for the Orion Launch Abort System (LAS) was developed largely from wind tunnel tests involving powered jet simulations of the rocket exhaust plumes, supported by computational fluid dynamics (CFD) simulations. The LAS contains three solid rocket motors used in various phases of an abort to provide propulsion, steering, and Launch Abort Tower (LAT) jettison from the Crew Module (CM). This paper describes a pair of wind tunnel experiments performed at transonic and supersonic speeds to determine the aerodynamic effects due to proximity and jet interactions during LAT jettison from the CM at the end of an abort. The tests were run using two different scale models at angles of attack from 150deg to 200deg , sideslip angles from -10deg to +10deg , and a range of powered thrust levels from the jettison motors to match various jet simulation parameters with flight values. Separation movements between the CM and LAT included axial and vertical translations as well as relative pitch angle between the two bodies. The paper details aspects of the model design, nozzle scaling methodology, instrumentation, testing procedures, and data reduction. Sample data are shown to highlight trends seen in the results.

Rhode, Matthew N.↗

Evaluating Deception Detection Model Robustness To Linguistic Variation

With the increasing use of automated, machine learning-driven tools and the downstream impact that algorithmic judgements can have, it is critical to develop models that are robust to evolving or manipulated inputs. Evaluating the reliability of multimodal models across linguistic variations to understand model susceptibility to intentional linguistic adversarial attacks as well as natural linguistic variations is essential in this pursuit. We present extensive analysis of model robustness and susceptibility to linguistic variations in the setting of deceptive news detection, a difficult classification task that is an increasingly important problem to solve with the impact of misinformation spread online. We evaluate the effectiveness of incorporating adversarial defense strategies and measure model susceptibility to state-of-the-art adversarial attacks using two types of linguistic attacks — character and word perturbations. We consider two multiclass prediction tasks — a 3-way classification of tweets as trustworthy, propaganda, or disinformation; and a 4-way classification as clickbait, hoax, satire, or conspiracy — and compare the performance of three embeddings that have been state-of-the-art for several NLP tasks — GloVe, ELMo, and BERT — to highlight consistent trends in susceptibility, high confidence misclassifications, and high impact failures. We find that character or mixed ensemble models are the most effective defense mechanisms and that character perturbations are a more effective attack than word perturbations for deception classification.

adversarial evaluation↗

Pressure distributions obtained on a 0.04-scale and 0.02-scale model of the Space Shuttle Orbiter's forward fuselage in the Langley continuous flow hypersonic tunnel

Results from pressure distribution tests on 0.04-scale and 0.02-scale models of the forward fuselage of the Space Shuttle Orbiter are presented without analysis. The tests wre completed in the Langley Continuous Flow Hypersonic Tunnel (CFHT). The 0.04-scale model was tested at angles of attack from -5 deg to 45 deg and angles of sideslip from -3 deg to 3 deg. The 0.02-scale model was tested at angles of attack from -10 deg to 45 deg and angles of sideslip from -5 deg to 5 deg. The tests were conducted in support of the development of the Shuttle Entry Air Data System (SEADS). In addition to modeling the 20 SEADS pressure orifices, the wind-tunnel models were also instrumented with orifices to match Development Flight Instrumentation (DFI) port locations currently existing on the Space Shuttle Orbiter Columbia (OV-102). This DFI simulation has provided a means for comparisons between reentry flight pressure data and wind-tunnel data.

Bradley, P. F.↗

Results of acoustic tests of a Prop-Fan model

Results of acoustic tests in a low speed open jet anechoic wind tunnel are presented for a counter rotation Prop-Fan model. The model tested had 5 front and 5 rear rotor blades with swept planform. Noise spectra are presented showing the influence of operating and configuration variables such as: (1) power absorption, (2) tip speed, (3) rotor-rotor spacing, (4) power split between the front and rear blade rows, (5) variation of the RPM ratio between front and rear blade rows, (6) tractor versus pusher (pylon effects), and (7) angle of attack. In addition to model scale results, calculated levels derived from test are presented showing the influence of the above variables on Effective Perceived Noise Level of a 13.1 ft diameter Prop-Fan at a flyover distance of 1500 ft. It was found that the strongest effects are caused by tip speed and power absorption. A significant finding was that there is an optimum operating tip speed for minimum noise for a given power absorption. Effects of other parametric variations are generally small but measurable. In order to minimize noise to meet airplane certification limits, operation at moderate tip speeds and power absorption is shown to be desirable. Accuracy of predicted Effective Perceived Noise Level is shown to be good with the best accuracy in the 590 to 670 ft/sec tip speed range.

Metzger, F.B.↗

Identification of aerodynamic models for maneuvering aircraft

The method based on Fourier functional analysis and indicial formulation for aerodynamic modeling as proposed by Chin and Lan is extensively examined and improved for the purpose of general applications to realistic airplane configurations. Improvement is made to automate the calculation of model coefficients, and to evaluate more accurately the indicial integral. Test data of large angle-of-attack ranges for two different models, a 70 deg. delta wing and an F-18 model, are used to further verify the applicability of Fourier functional analysis and validate the indicial formulation. The results show that the general expression for harmonic motions throughout a range of k is capable of accurately modeling the nonlinear responses with large phase lag except in the region where an inconsistent hysteresis behavior from one frequency to the other occurs. The results by the indicial formulation indicate that more accurate results can be obtained when the motion starts from a low angle of attack where hysteresis effect is not important.

Lan, C. Edward↗

Effect of periodic changes of angle of attack on behavior of airfoils

This report presents the results of a series of experiments, which gave some quantitative results on the effect of periodic changes in the direction of the relative air flow against airfoils. The first series of experiments concerned how the angle of attack of the wing model was changed by causing the latter to oscillate about an axis parallel to the span and at right angles to the air flow. The second series embraced all the experiments in which the direction of the air flow itself was periodically changed.

AIRFOILS - ANGLE OF ATTACK↗

Laser transit anemometer measurements on a slender cone in the Langley unitary plan wind tunnel

A laser transit anemometer (LTA) system was used to probe the boundary layer on a slender (5 degree half angle) cone model in the Langley unitary plan wind tunnel. The anemometer system utilized a pair of laser beams with a diameter of 40 micrometers spaced 1230 micrometers apart to measure the transit times of ensembles of seeding particles using a cross-correlation technique. From these measurements, boundary layer profiles around the model were constructed and compared with CFD calculations. The measured boundary layer profiles representing the boundary layer velocity normalized to the edge velocity as a function of height above the model surface were collected with the model at zero angle of attack for four different flow conditions, and were collected in a vertical plane that bisected the model's longitudinal center line at a location 635 mm from the tip of the forebody cone. The results indicate an excellent ability of the LTA system to make velocity measurements deep into the boundary layer. However, because of disturbances in the flow field caused by onboard seeding, premature transition occurred implying that upstream seeding is mandatory if model flow field integrity is to be maintained. A description and results of the flow field surveys are presented.

Humphreys, William M., Jr.↗

Boundary Layer Transition on Slender Cones in Conventional and Low Disturbance Mach 6 Wind Tunnels

An experimental investigation was conducted on a 5-degree half-angle cone and a 5-degree half-angle flared cone in a conventional Mach 6 wind tunnel to examine the effects of facility noise on boundary layer transition. The influence of tunnel noise was inferred by comparing transition onset locations determined from the present test to that previously obtained in a Mach 6 low disturbance quiet tunnel. Together, the two sets of experiments are believed to represent the first direct comparison of transition onset between a conventional and a low disturbance wind tunnel using a common test model and transition detection technique. In the present conventional hypersonic tunnel experiment, separate measurements of heat transfer and adiabatic wall temperatures were obtained on the conical models at small angles of attack over a range of Reynolds numbers, which resulted in laminar, transitional, and turbulent flow. Smooth model turbulent heating distributions are compared to that obtained with transition forced via discrete surface roughness. The model nosetip radius was varied to examine the effects of bluntness on transition onset. Despite wall to total temperature differences between the transient heating measurements and the adiabatic wall temperature measurement, the two methods for determining sharp cone transition onset generally yielded equivalent locations. In the 'noisy' mode of the hypersonic low disturbance tunnel, transition onset occurred earlier than that measured in the conventional hypersonic tunnel, suggesting higher levels of freestream acoustic radiation relative to the conventional tunnel. At comparable freestream conditions, the transition onset Reynolds number under low disturbance conditions was a factor of 1.3 greater than that measured on flared cone in the LaRC conventional hypersonic tunnel and a factor of 1.6 greater that the flared cone run in the low disturbance tunnel run 'noisy'. Navier-Stokes mean flow computations and linear stability analysis were conducted to assess the experimental results and have indicated N factors associated with sharp flared cone transition onset to be approximately a factor of 2 lower than that inferred from the corresponding low disturbance tunnel measurements.

Horvath, Thomas J.↗