Search NASA⌕ Search

SEARCH · Search NASA

Results for “beam loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Improvement of a plasma uniformity of the 2nd ion source of KSTAR neutral beam injector

The 2nd ion source of KSTAR (Korea Superconducting Tokamak Advanced Research) NBI (Neutral Beam Injector) had been developed and operated since last year. A calorimetric analysis revealed that the heat load of the back plate of the ion source is relatively higher than that of the 1st ion source of KSTAR NBI. The spatial plasma uniformity of the ion source is not good. Therefore, we intended to identify factors affecting the uniformity of a plasma density and improve it. We estimated the effects of a direction of filament current and a magnetic field configuration of the plasma generator on the plasma uniformity. We also verified that the operation conditions of an ion source could change a uniformity of the plasma density of an ion source.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Magnet designs for muon collider ring and interactions regions

Conceptual designs of superconducting magnets for the storage ring of a Muon Collider with a 1.5 TeV c.o.m. energy and an average luminosity of 10{sup 34} cm{sup -2}s{sup -1} are presented. All magnets are based on Nb{sub 3}Sn superconductor and designed to provide an adequate operating field/field gradient in the aperture with the critical current margin required for reliable magnet operation in the machine. Magnet cross-sections were optimized to achieve the accelerator field quality in the magnet aperture occupied with beams. The magnets and corresponding protective measures are designed to handle about 0.5 kW/m of dynamic heat load from the muon beam decays. Magnet parameters are reported and compared with the requirements.

43 PARTICLE ACCELERATORS↗

Effect of ion-beam treatment on structure and fracture resistance of 12Cr1MoV steel under static, cyclic and dynamic loading

Features of the structure and properties modification of 12Cr1MoV steel subjected to irradiation by zirconium ion beam have been investigated with the use of optical and electron microscopy as well as microhardness measurement. It has been shown that upon treatment the structure modification occurred across the entire cross-section of specimens with the thickness of 1 mm. Changes in the mechanical properties of these specimens under static, cyclic and impact loading are interpreted in terms of identified structure changes.

36 MATERIALS SCIENCE↗

Fatigue analysis of the Spallation Neutron Source 2 MW target design

Upgrades to the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory are under way with two major projects. The first project is the Proton Power Upgrade (PPU), which will double the power capacity of the SNS accelerator system to enable the operation of a future second neutron source target station—the second project. PPU also will increase power to the SNS first target station – which currently operates at 1.4 MW with 1.0 GeV protons – to 2 MW with 1.3 GeV protons. Final design of the PPU 2 MW target module is finished, including all necessary design and analysis calculations. The fatigue evaluation described herein is an assessment of the fitness of the PPU 2 MW target mercury vessel to resist failure from cyclic loading from the pulsed 60 Hz proton beam and thermal changes from disrupted operation. In addition to the reliability predictions, the method, detail, and depth of this fatigue evaluation are superior to those of past target design assessments. Furthermore, the thermal fatigue life is predicted to exceed 3125 thermal cycles per 1250 h of operation for all load cases. The design also meets the (relative) fatigue design goal for combined thermal and pulse loading of greater than 0.5 times the minimum fatigue life calculated for a jet-flow target design operating at 1.4 MW—the most robust design to date in terms of resistance to fatigue failure. From the onset of the PPU, it has been known that pulse loading requires effective application of helium gas injection into the target mercury to reduce beam pressure loading. For the PPU 2 MW target, none of the pulse load cases requires a maximum strain reduction from gas injection of more than 50% (for base material) to meet the fatigue design goal. This level of reduction is achievable from gas injection, according to historical strain measurements from 1.4 MW target operation. Overall, the PPU 2 MW target design is predicted to have superior resistance to fatigue failure compared with past target designs.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Load-shortening behavior of an initially curved eccentrically loaded column

To explore the feasibility of using buckled columns to provide a soft support system for simulating a free-free boundary condition in dynamic testing, the nonlinear load-shortening behavior of initially imperfect, eccentrically loaded slender columns is analyzed. Load-shortening curves are obtained for various combinations of load eccentricity and uniform initial curvature and are compared, for reference purposes, with the limiting case of the classical elastica. Results for numerous combinations of initial curvature and load eccentricity show that, over a wide range of shortening, an axially loaded slender column exhibits load-deflection compliance which is of the same order as that of a straight but otherwise identical cantilever beam under lateral tip loading.

Fichter, W. B.↗

Rollable Corrugated Tubular Booms

A promising candidate for a new class of deployable composite boom is the COrrugated ROllable TUbular Boom (COROTUB), which is to be employed on future large space structures by the National Aeronautics and Space Administration (NASA). The COROTUB’s two corrugated thin shells form a closed section, which yields high bending and torsional stiffness, allowing for high dimensional stability. The corrugation geometry that dictates the boom cross-section shape was completely defined by closed-form analytical equations given a set of key design parameters. Parametric studies of two geometric variables were used to evaluate which parameters most influence the cross-section’s area moment of inertia and torsional constant. The number of corrugations, flattened height of the boom, and concave and convex corrugation radii were varied to study the complete boom design space. Deeper corrugations increased the local buckling (crimpling) loads of the thin-shell boom but reduced the area moment of inertia and therefore the global buckling load of the beam-column member, and thus a fine balance was sought. Finite element analyses of pure bending and compression load cases for short, 1.22-m-long fully-deployed booms ofeither the same size (flattened height) or similar inertia properties, were first carried out to efficiently study this design trade-off in detail.A second computational study evaluated the boom transition shape and the structural response of a 6-m-long partially-deployed boom, where the effects of partially bracing the root of the boom were also assessed. It was found that bracing length could greatly affect the strength and stiffness of this boom.Bracing type (as in the discrete number of clamps at the root) had no effect on stiffness, but particularly impacted strength for loading cases and boundary conditions that promoted the onset of local web buckling at the root. The corrugated designs were also found to improve, by as much as 20%, the boom bending and axial strength and boom transition length from flat to deployed when compared to a state-of-the-art boom alternative of the same size, for short bracing distances, such as those that would be required by small satellite applications. In addition, they showed a comparable structural response for longer bracing supports.

Booms↗

Mathematical modelling of the beam under axial compression force applied at any point – the buckling problem

The study is devoted to stability of simply supported beam under axial compression. The beam is subjected to an axial load located at any point along the axis of the beam. The buckling problem has been desribed and solved mathematically. Critical loads have been calculated. In the particular case, the Euler’s buckling load is obtained. Explicit solutions are given. The values of critical loads are collected in tables and shown in figure. The relation between the point of the load application and the critical load is presented.

97 MATHEMATICS AND COMPUTING↗

Ultracold Molecules: Physics in the Quantum Regime

Our research encompasses approaches to the trapping of diatomic molecules at low temperature plus the cooling and detection of polyatomic molecules in the kelvin temperature regime. We have cooled and trapped CaF and/or CaH molecules, loaded directly from a molecular beam. As part of this work, we are continuing to develop an important trapping technique, optical loading from a buffer-gas beam. This method was invented in our lab. We are also studying cold polyatomic molecules and their interactions with cold atoms.

74 ATOMIC AND MOLECULAR PHYSICS↗

Liquid Rocket Booster (LRB) for the Space Transportation System (STS) systems study. Appendix E: Pressure-fed booster test bed for the liquid rocket booster study

The stress analysis/structural design of the Pressure-Fed Booster Engine Test Bed using the existing F-1 Test Facility Test Stand at Huntsville, Alabama is described. The analysis has been coded and set up for solution on NASTRAN. A separate stress program was established to take the NASTRAN output and perform stress checks on the members. Joint checks and other necessary additional checks were performed by hand. The notes include a brief description of other programs which assist in reproducing and reviewing the NASTRAN results. The redesign of the test stand members and the stress analysis was performed per the A.I.S.C. Code. Loads on the stand consist of the loaded run tanks; wind loads; seismic loads; live loads consisting of snow and ice: live and dead loads of steel; and loaded pressurant bottle. In combining loads, wind loads and seismic loads were each combined with full live loads. Wind and seismic loads were not combined. No one third increase in allowables was taken for the environmental loads except at decks 147 and 214, where the increase was used when considering the stay rods, brackets and stay beams. Wind and seismic loads were considered from each of the four coordinate directions (i.e. N,S,E,W) to give eight basic conditions. The analysis was run with the pressurant tank mounted at level 125. One seismic condition was also run with the tank mounted at levels 169 and 214. No failures were noted with mounting at level 169, but extensive deck failure with mounting at level 214 (the loadsets used are included on the tape, but no detailed results are included in the package). Decking support beams at levels 147 and 214 are not included in the model. The stress program thus does not reduce strut lengths to the length between support beams (the struts are attached to the beams at intersection points) and gives stress ratios larger than one for some of the struts. The affected members were therefore checked by hand.

Source record↗

Modeling and simulation performance of sucker rod beam pump

Artificial lift is a mechanism to lift hydrocarbon, generally petroleum, from a well to surface. This is used in the case that the natural pressure from the reservoir has significantly decreased. Sucker rod beam pumping is a method of artificial lift. Sucker rod beam pump is modeled in this research as a function of geometry of the surface part, the size of sucker rod string, and fluid properties. Besides its length, sucker rod string also classified into tapered and un-tapered. At the beginning of this research, for easy modeling, the sucker rod string was assumed as un-tapered. The assumption proved non-realistic to use. Therefore, the tapered sucker rod string modeling needs building. The numerical solution of this sucker rod beam pump model is computed using finite difference method. The numerical result shows that the peak of polished rod load for sucker rod beam pump unit C-456-D-256-120, for non-tapered sucker rod string is 38504.2 lb, while for tapered rod string is 25723.3 lb. For that reason, to avoid the sucker rod string breaks due to the overload, the use of tapered sucker rod beam string is suggested in this research.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Simultaneous control and optimization for elastic systems

Studies are conducted to determine the dynamic response of beams and plates to loads which are extreme within a certain class of admissible loads. Two approaches to this problem are suggested. In approach one, Pontryagin's maximality principle is regarded as an additional constraint. The optimality of design is then determined by standard numerical techniques. The "adjoint variable approach' to sensitivity of structural design is applied for a given inhomogeneous term. The inhomogeneous term is an extremal element of admissible load vectors, which constitute a closed subspace of a Sobolev space. Again, the maximality principle is invoked. While only beam and plate theory problems are used as examples, generalizations are easy to perceive.

Komkov, V.↗

Interaction of HOMs in periodic accelerating structures

The paper discusses the HOM interaction effect in a 5-cell 650 MHz HB cavity prototype for the PIP-II project. This effect may lead to flat HOM passbands. In the presence of misalignments, this passband disintegrates into individual cell resonances that are not coupled to the beam pipes and, therefore, have a high-quality factor and R/Q ratio. These resonances can lead to excessive cryogenic loading, increased emittance, and beam instabilities. An analytical theory has been developed to explain this effect, as well as special methods for eliminating it.

Yakovlev, V. [Fermilab]↗

The structural optimization of a spreader bar for twin lift helicopter operations

An optimization study was performed to develop a minimum weight spreader bar to allow two helicopters to lift the same payload. With this arrangement, the maximum payload that can be lifted is almost doubled without the expense of designing and building a new helicopter. The concept has had some limited use by civil helicopter operators using small helicopters and has been demonstrated in large scale by two CH-54's which successfully lifted a total load of 20 ton. To this point, rather heavy available beams or tower structures have been used for the spreader bar. Since the weight of the bar not only detracts from payload but also adds to the logistics problem, there are more than the usual incentives to minimize weight. Since the design requirement is for classic beam column with uniform side loads resulting from bar weight and aerodynamic drag, the design problem is particularly amenable to optimization. A study has been performed at Sikorsky to establish the minimum weight for a spreader bar sized to carry a load equal to the capacity of two Army BLACK HAWK helicopters. Toward this end, a computer program was written to analyze the spreader bar deflections and stresses and coupled to the NASA developed CONMIN optimization routines.

Dobyns, A.↗

Evaluation of mounting bolt loads for Space Shuttle Get Away Special (GAS) adapter beam

During the prototype vibration tests of the GAS adapter beam, significant impacting of the beam at its support points was observed. The cause of the impacting was traced to gaps under the mounting bolt heads. Because of the nonlinear nature of the response, it was difficult to evaluate the effects which Shuttle launch dynamics might have on the mounting bolt loads. A series of tests were conducted on an electrodynamic exciter in which the transient acceleration time histories, which had been measured during the Space Transportation System-1 (STS-1; Space Shuttle mission 1) launch, were simulated. The actual flight data had to be filtered and compensated so that it could be reproduced on the shaker without exceeding displacement and velocity limitations. Mounting bolt loads were measured directly by strain gages applied to the bolts. Various gap thicknesses and bolt torques were investigated. Although increased gap thickness resulted in greater accelerations due to impacting, the bolt loads were not significantly affected. This is attributed to the fact that impacting excited mostly higher frequency modes which do not have significant modal mass.

Talapatra, D. C.↗

Electromagnetic and hadronic interactions of ultrarelativistic nuclei

Beam nuclei accelerated at the Large Hadron Collider (LHC) at CERN are lost due to interactions with the counter-rotating beam, residual gas, and accelerator elements. Proper modelling of the beam transport and radiation load on accelerator components requires reliable prediction of the yields of nuclear fragments produced in electromagnetic dissociation and hadronic fragmentation of beam nuclei. We investigate electromagnetic and hadronic fragmentation of lead nuclei in collisions with various nuclei and single electrons at the injection and collision energies of the LHC. The consideration is based on the RELDIS and abrasion-ablation models. Since this approach well describes Pb fragmentation data at 30 and 158 A GeV, its validity for Pb nuclei at the LHC collision energy is also expected.

43 PARTICLE ACCELERATORS↗

Comparison of advanced reduced-basis methods for transient structural analysis

Two advanced reduced-basis methods for linear, transient structural analysis, the force-derivative method and the Lanczos method, are compared to two widely-used modal methods, the mode-displacement method and the mode-acceleration method. Comparisons are made for two linear example problems: a proportionally-damped cantilevered beam subject to a discrete tip load which varies linearly with time, and a discretely-damped multispan beam subject to a uniformly distributed load which varies as a quintic function of time. Results from the methods are compared in terms of the number of basis vectors required to obtain a desired level of accuracy and the associated computational times. The results are problem dependent, and it is shown that for the cantilevered beam problem, the mode-acceleration and force-derivative methods are the most efficient in terms of the number of basis vectors and computational time. The force-derivative method is shown to be the most effective method for solving the multispan beam problem with closely-spaced frequencies. In general, the force-derivative method is shown to produce an accurate solution using very few basis vectors and to require less computational time as compared to the other methods studied.

Mcgowan, David M.↗

Laser-cooled atoms inside a hollow-core photonic-crystal fiber

We describe the loading of laser-cooled rubidium atoms into a single-mode hollow-core photonic-crystal fiber. Inside the fiber, the atoms are confined by a far-detuned optical trap and probed by a weak resonant beam. We describe different loading methods and compare their trade-offs in terms of implementation complexity and atom-loading efficiency. The most efficient procedure results in loading of {approx}30,000 rubidium atoms, which creates a medium with an optical depth of {approx}180 inside the fiber. Compared to our earlier study this represents a sixfold increase in the maximum achieved optical depth in this system.

74 ATOMIC AND MOLECULAR PHYSICS↗

Development of a cryogenic load frame for the neutron diffractometer at Takumi in Japan Proton Accelerator Research Complex

To prepare for projects such as the Large Hadron Collider upgrade, International Thermonuclear Experimental Reactor and Demonstration reactor, it is important to form a clear understanding of stress-strain properties of the materials that make up superconducting magnets. Thus, we have been studying the mechanical properties of superconducting wires using neutron diffraction measurements. To simulate operational conditions such as temperature, stress, and strain, we developed a cryogenic load frame for stress-strain measurements of materials using a neutron diffractometer at Japan Proton Accelerator Research Complex (J-PARC) Takumi beam line. The maximum load that can be applied to a sample using an external driving machine is 50 kN. Using a Gifford-MacMahon cryocooler, samples can be measured down to temperatures below 10 K when loaded. In the present paper, we describe the details of the cryogenic load frame with its test results by using type-304 stainless steel wire.

43 PARTICLE ACCELERATORS↗