Search NASA⌕ Search

SEARCH · Search NASA

Results for “boundary layer height”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Effects of Step Shape on Transition over a Swept Backward-Facing Step

The effect of backward-facing step shape on stationary-crossflow growth was studied down-stream of a two-dimensional step in a swept-wing flow. The step height was set at 76% of the local unperturbed boundary-layer thickness at the step location, and the shape was varied by placing three ramps of differing slopes and shapes on the downstream face of the step, including a 30◦ramp, rounded ramp, and a 5◦ramp. In addition, the square step shape (with noramp) was studied. The 5◦ramp was the only one that was successful at substantially delaying transition downstream of the step. Even so, it did not completely mitigate the effect of the step. The 5◦ramp significantly altered the mean flow, significantly reducing the separation region downstream of the step. While this geometry still resulted in increased growth of the stationary crossflow instability, it substantially reduced the amplitude of the unsteady instabilities that grew downstream of the step. In particular, this ramp completely eliminated the low-frequency, traveling crossflow mode that was observed in the other cases.

Jenna L Eppink↗
NASA NTRS2012

Receptivity of Hypersonic Boundary Layers to Distributed Roughness and Acoustic Disturbances

Boundary-layer receptivity and stability of Mach 6 flow over smooth and rough 7 half-angle sharp-tipped cones are numerically investigated. The receptivity of the boundary layer to slow acoustic disturbances, fast acoustic disturbances, and vortical disturbances are considered. The effects of two-dimensional isolated and distributed roughness on the receptivity and stability are also simulated. The results show that the instability waves are generated in the leading edge region and that the boundary layer is much more receptive to slow acoustic waves than to the fast waves. Vortical disturbances also generate unstable second modes, however the receptivity coefficients are smaller than that of the slow acoustic wave. An isolated two-dimensional roughness element of height h/delta =1/4 did not produce any difference in the receptivity or in the stability of the boundary layer. Distributed roughness elements produced a small decrease in the receptivity coefficient and also stabilized the boundary layer by small amounts.

Balakumar, Ponnampalam↗
NASA NTRS2019

Biomass-Burning Smoke Heights over the Amazon Observed from Space

We characterise the vertical distribution of biomass-burning emissions across the Amazon during the biomass-burning season (July–November) with an extensive climatology of smoke plumes derived from MISR and MODIS (2005–2012) and CALIOP (2006–2012) observations. Smoke plume heights exhibit substantial variability, spanning a few hundred metres up to 6 km above the terrain. However, the majority of the smoke is located at altitudes below 2.5 km. About 60 % of smoke plumes are observed in drought years, 40 %–50 % at the peak month of the burning season (September) and 94 % over tropical forest and savanna regions, with respect to the total number of smoke plume observations. At the time of the MISR observations (10:00–11:00 LT), the highest plumes are detected over grassland fires (with an averaged maximum plume height of ∼1100 m) and the lowest plumes occur over tropical forest fires (∼800 m). A similar pattern is found later in the day (14:00–15:00 LT) with CALIOP, although at higher altitudes (2300 m grassland vs. 2000 m tropical forest), as CALIOP typically detects smoke at higher altitudes due to its later overpass time, associated with a deeper planetary boundary layer, possibly more energetic fires, and greater sensitivity to thin aerosol layers. On average, 3 %–20 % of the fires inject smoke into the free troposphere; this percentage tends to increase toward the end of the burning season (November: 15 %–40 %). We find a well-defined seasonal cycle between MISR plume heights, MODIS fire radiative power and atmospheric stability across the main biomes of the Amazon, with higher smoke plumes, more intense fires and reduced atmospheric stability conditions toward the end of the burning season. Lower smoke plume heights are detected during drought (800 m) compared to non-drought (1100 m) conditions, in particular over tropical forest and savanna fires. Drought conditions favour understory fires over tropical forest, which tend to produce smouldering combustion and low smoke injection heights. Droughts also seem to favour deeper boundary layers and the percentage of smoke plumes that reach the free troposphere is lower during these dry conditions. Consistent with previous studies, the MISR mid-visible aerosol optical depth demonstrates that smoke makes a significant contribution to the total aerosol loading over the Amazon, which in combination with lower injection heights in drought periods has important implications for air quality. This work highlights the importance of biome type, fire properties and atmospheric and drought conditions for plume dynamics and smoke loading. In addition, our study demonstrates the value of combining observations of MISR and CALIOP constraints on the vertical distribution of smoke from biomass burning over the Amazon.

Gonzalez-Alonso, Laura↗
DOE OSTI2023

Gulf of Mexico Offshore Wind Energy Hurricane Risk Assessment

NREL's feasibility assessment of offshore wind in the Gulf of Mexico concluded that hurricane risk was one of the major challenges that would need to be overcome for a mature offshore wind industry to develop in the Gulf of Mexico. To ensure the robust design of wind turbines in the Gulf of Mexico, it is critical to understand the added risk posed by the threat of major hurricanes, as those affecting the Gulf of Mexico region have a significant potential to exceed design limits prescribed by the International Electrotechnical Commission (IEC) wind design standards. To satisfy this charge, this project defines the wind hazard for the Gulf of Mexico Offshore Wind Energy area using the hurricane hazard model develop by Applied Research Associates and published extensively in the open literature. In doing so, the return periods associated with the IEC Class 1A and Typhoon Class limit-state hurricanes are estimated on a grid with nominal resolution of 10 km to determine where hurricane risk results in the exceedance of the IEC design criteria. On the same grid, wind speeds hazard contours associated with return periods varying from 50 to 1,000 years are also estimated. An additional challenge in assessing hurricane wind speed risk in the Gulf of Mexico arises from inconsistent terminology across the Saffir-Simpson hurricane scale and the IEC design criteria. Saffir-Simpson definitions are based on 1-minute sustained wind speeds estimated at 10-m height over marine terrain, while the IEC uses a different averaging period (3-second versus 1-minute) and reference height (assumed herein a hub height of 150 m versus 10 m). Employing the latest research on turbulence characteristics of the hurricane boundary layer, conversions between various durations (e.g., 3-seconds, 1-minute, 10-minutes, 1-hour) and between elevations near the surface (10 m) to near hub height (assumed herein 150 m) are developed. IEC Class 1A and Typhoon Class limit states are also provided in terms of an equivalent Saffir-Simpson hurricane wind speed category.

17 WIND ENERGY↗
NASA NTRS1984

Optimization and application of riblets for turbulent drag reduction

Riblet surfaces have been tested in boundary layers having different upstream histories and at higher Reynolds numbers than previously reported. The drag reduction for the riblet surfaces was found to be dependent on the height and spacing of the riblets in law-of-the-wall variables regardless of the free-stream Reynolds number or upstream boundary-layer history. Micro-photographs of the actual riblet geometries are examined to determine the effect of rib details on the riblet drag-reduction performances. To further increase drag-reduction performance, riblet surfaces are combined with another drag-reduction concept, the large-eddy breakup device (LEBU). In addition, the yaw sensitivity of riblets is evaluated, as well as the characteristics of riblet surfaces manufactured out of a thin vinyl sheet.

Walsh, M. J.↗
NASA NTRS1973

A model of wind shear and turbulence in the surface boundary layer

A model of wind and turbulence has been described for the surface boundary layer. The wind structure in the surface layer is considered to be a function of the surface parameters, stability, and height. The surface parameters considered are: (1) the surface roughness length; (2) the surface friction velocity; and (3) the zero plane displacement height. The stability parameter, Z/L, where L is the Monin-Obukov stability length, describes the thermal effect on the wind profile. The logarithmic wind profile is used to describe the mean wind field in the neutral boundary layer, and a logarithmic profile with a stability defect is used to describe the stable and unstable atmospheric conditions. For the very stable conditions, the logarithmic wind law does not hold. Under this condition, the layers of the atmosphere become disconnected and large scale frontal motions are the predominate factor in defining the wind profile. Figures are presented which represent some typical wind profiles in the very stable condition.

Luers, J. K.↗
NASA NTRS1978

Theoretical investigation of maintaining the boundary layer of revolution laminar using suction slits in incompressible flow

The transition of the laminar boundary layer into the turbulent state, which results in an increased drag, can be avoided by sucking of the boundary layer particles near the wall. The technically-interesting case of sucking the particles using individual slits is investigated for bodies of revolution in incompressible flow. The results of the variational calculations show that there is an optimum suction height, where the slot separations are maximum. Combined with favorable shaping of the body, it is possible to keep the boundary layer over bodies of revolution laminar at high Reynolds numbers using relatively few suction slits and small amounts of suction flow.

Thiede, P.↗
NASA NTRS1993

Boundary layer flow of air over water on a flat plate

A non-similar boundary layer theory for air blowing over a water layer on a flat plate is formulated and studied as a two-fluid problem in which the position of the interface is unknown. The problem is considered at large Reynolds number (based on x), away from the leading edge. A simple non-similar analytic solution of the problem is derived for which the interface height is proportional to x(sub 1/4) and the water and air flow satisfy the Blasius boundary layer equations, with a linear profile in the water and a Blasius profile in the air. Numerical studies of the initial value problem suggests that this asymptotic, non-similar air-water boundary layer solution is a global attractor for all initial conditions.

Nelson, John↗
NASA NTRS2010

Micro-Ramp Flow Control for Oblique Shock Interactions: Comparisons of Computational and Experimental Data

Computational fluid dynamics was used to study the effectiveness of micro-ramp vortex generators to control oblique shock boundary layer interactions. Simulations were based on experiments previously conducted in the 15 x 15 cm supersonic wind tunnel at NASA Glenn Research Center. Four micro-ramp geometries were tested at Mach 2.0 varying the height, chord length, and spanwise spacing between micro-ramps. The overall flow field was examined. Additionally, key parameters such as boundary-layer displacement thickness, momentum thickness and incompressible shape factor were also examined. The computational results predicted the effects of the micro-ramps well, including the trends for the impact that the devices had on the shock boundary layer interaction. However, computing the shock boundary layer interaction itself proved to be problematic since the calculations predicted more pronounced adverse effects on the boundary layer due to the shock than were seen in the experiment.

Hirt, Stefanie M.↗
NASA NTRS1982

Supersonic burning in separated flow regions

The trough vortex phenomena is used for combustion of hydrogen in a supersonic air stream. This was done in small sizes suitable for igniters in supersonic combustion ramjets so long as the boundary layer displacement thickness is less than 25% of the trough step height. A simple electric spark, properly positioned, ignites the hydrogen in the trough corner. The resulting flame is self sustaining and reignitable. Hydrogen can be injected at the base wall or immediately upstream of the trough. The hydrogen is introduced at low velocity to permit it to be drawn into the corner vortex system and thus experience a long residence time in the combustion region. The igniters can be placed on a skewed back step for angles at least up to 30 deg. without affecting the igniter performance significantly. Certain metals (platinum, copper) act catalytically to improve ignition.

Zumwalt, G. W.↗
NASA NTRS1984

The role of airfoil geometry in minimizing the effect of insect contamination of laminar flow sections

A method has been developed to predict the contamination of an airfoil by insects and the resultant performance penalty. Insect aerodynamics have been modeled and the impingement of insects on an airfoil are solved by calculating their trajectories. Upon impact, insect rupture and the resulting height of the debris is determined based on experimental data. A boundary layer analysis is performed to determine which insects cause boundary layer transition and the resultant drag penalty. A contaminated airfoil figure of merit is presented to be used to compare airfoil susceptibility. Results show that the insect contamination effects depend on accretion conditions, airfoil angle of attack and Reynolds number. The importance of the stagnation region to designing airfoils for minimum drag penalties is discussed.

Maresh, J. L.↗
NASA NTRS1986

Low-Noise Supersonic Nozzle

Two-dimensional nozzle incorporates unusual design features of rapid expansion contour, boundary-layer bleed slots upstream of throat, and exit width-to-height ratio of 1.7 to provide noise levels in upstream regions of test rhombus substantially lower than in conventional nozzles.

Beckwith, I. E.↗
NASA NTRS1992

Remote Sensing by Spaceborne Lidar Aided by Surface Returns

Spaceborne lidar offers the possibility of global mapping of clouds and atmospheric aerosols. Mapping of cloud-top heights, multiple layers of thin clouds and the depth of the planetary boundary layer (PBL), given sufficient aerosols, are applications that should be fairly easy to accomplish from space with even a modest lidar system. However, the constraints imposed on spaceborne lidar by large ranging distances, limited available power/weight, and fast moving platforms present significant challenges to achieving more quantitative retrievals such as extracting aerosol extinction profiles, PBL optical depths and cloud optical depths. Ways to take advantage of the strong signals available from ground/sea reflections to improve upon atmospheric aerosol and cloud retrievals as well as to distinguish certain surface types are explored.

Reagan, J. A.↗
NASA NTRS2012

Micro-Ramp Flow Control for Oblique Shock Interactions: Comparisons of Computational and Experimental Data

Computational fluid dynamics was used to study the effectiveness of micro-ramp vortex generators to control oblique shock boundary layer interactions. Simulations were based on experiments previously conducted in the 15- by 15-cm supersonic wind tunnel at the NASA Glenn Research Center. Four micro-ramp geometries were tested at Mach 2.0 varying the height, chord length, and spanwise spacing between micro-ramps. The overall flow field was examined. Additionally, key parameters such as boundary-layer displacement thickness, momentum thickness and incompressible shape factor were also examined. The computational results predicted the effects of the microramps well, including the trends for the impact that the devices had on the shock boundary layer interaction. However, computing the shock boundary layer interaction itself proved to be problematic since the calculations predicted more pronounced adverse effects on the boundary layer due to the shock than were seen in the experiment.

Hirt, Stephanie M.↗
NASA NTRS1997

Boundary Layer Receptivity to Three-Dimensional Freestream Disturbances at Two-Dimensional Roughness

The receptivity of a laminar boundary layer to an isolated three-dimensional convected disturbance is investigated in a low-speed wind tunnel experiment. The disturbance is created by the short-duration pulsed displacement of a small low-aspect-ratio wing located upstream of a flat plate. The height of the wing is set so that the convected disturbance grazes the edge of the flat-plate boundary layer. A receptivity site is provided by a two-dimensional roughness strip on the surface of the plate. The different propagation speeds of acoustic, convected and instability waves cause the various wave packets from the pulsed displacement to arrive at a downstream measurement station at different times, separating the phenomena and allowing them to be studied independently. Ensemble- averaged measurements are made with and without roughness on the plate. Preliminary analysis of the measurements suggest the presence of a two-dimensional T-S wave packet arising from an interaction between an acoustic wave and the roughness, and a three-dimensional T-S wave packet arising from an interaction between the localized convected disturbance and the roughness strip. The growth rates and spatial characteristics of the disturbances and the instability wave packets are measured as they propagate downstream.

Dietz, Anthony↗
NASA NTRS2021

PBL Height from AIRS, GPS RO, and MERRA-2 Products in NASA GES DISC and Their 10 Year Seasonal Mean Intercomparison

Within the planetary boundary layer (PBL), surface forcing response, drag, turbulence, and vertical mixing are important processes and play a more critical role here than in the overlying “free atmosphere”. The PBL Height (PBLH) is an important parameter in climate models, weather forecasts, and air quality prediction. The NASA Goddard Earth Sciences Data and Information Services Center (GES DISC) provides data processing, archiving, and distribution services for numerous Earth science products. PBLH is a parameter in three products served by GES DISC, which are from the Atmospheric Infrared Sounder (AIRS), the Global Positioning System (GPS) radio occultation (RO) experiment, and the NASA reanalysis product Modern-Era Retrospective analysis for Research and Applications – 2 (MERRA-2). These products have different spatial and temporal resolutions and coverages, and their PBLH definitions are also different. To better serve the PBL research community, we have summarized the specifications of these products. A ten-year seasonal mean intercomparison is also conducted to provide further guidance to users. The intercomparison results show that MERRA-2 has a much shallower PBL than AIRS and GPS RO. An experimental study indicates the different PBLH definition in MERRA-2 caused smaller values of PBLH. The improvement of the water vapor retrieval in AIRS version 7 over version 6 results in the version 7 PBLH agreeing better with GPS RO and MERRA-2 than version 6, especially near the equator and low latitudes.

Feng Ding↗
NASA NTRS2007

Spatial Correlation and Coherence of Boundary Layer Winds Near Cape Canaveral Florida

The spatial correlation and coherence of winds over separation distances from 8.5 to 31 km based on central Florida data from November 1999 through August 2001 are presented. The winds at altitudes from 500 to 3000 m were measured using a network of five radar wind profilers. The goal was to determine the extent to which the profilers may be considered independent data sources. Quality controlled profiles were produced every 15 minutes for up to sixty gates, each representing 101 m in altitude over the range from 130 m to 6089 m. Five levels, each containing three consecutive gates, were selected for analysis. These levels covered the range from 433 to 3059 m. The results show that the profilers are independent for features having time scales of less than one hour in the winter or two hours in the summer. This does not depend significantly on height. Because the size of the network coincides with the "spectral gap" in the boundary layer, the result also does not depend on the spacing of the profilers within the network.

Merceret, Francis J.↗
NASA NTRS2012

Mixed Layer Heights Derived from the NASA Langley Research Center Airborne High Spectral Resolution Lidar

The NASA airborne High Spectral Resolution Lidar (HSRL) has been deployed on board the NASA Langley Research Center's B200 aircraft to several locations in North America from 2006 to 2012 to aid in characterizing aerosol properties for over fourteen field missions. Measurements of aerosol extinction (532 nm), backscatter (532 and 1064 nm), and depolarization (532 and 1064 nm) during 349 science flights, many in coordination with other participating research aircraft, satellites, and ground sites, constitute a diverse data set for use in characterizing the spatial and temporal distribution of aerosols, as well as properties and variability of the Mixing Layer (ML) height. We describe the use of the HSRL data collected during these missions for computing ML heights and show how the HSRL data can be used to determine the fraction of aerosol optical thickness within and above the ML, which is important for air quality assessments. We describe the spatial and temporal variations in ML heights found in the diverse locations associated with these experiments. We also describe how the ML heights derived from HSRL have been used to help assess simulations of Planetary Boundary Layer (PBL) derived using various models, including the Weather Research and Forecasting Chemistry (WRF-Chem), NASA GEOS-5 model, and the ECMWF/MACC models.

Scarino, Amy J.↗