Search NASA⌕ Search

SEARCH · Search NASA

Results for “catalyst loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Coupled methane and NO x conversion on Pt + Pd/Al 2 O 3 monolith: Conversion enhancement through feed modulation and Mn 0.5 Fe 2.5 O 4 spinel addition

The performance of a dual-layer Pt-Pd/Al 2 O 3 washcoated monolith promoted by an Al 2 O 3 -supported Mn 0.5 Fe 2.5 O 4 spinel base layer was evaluated with the objective to develop a catalyst with a lower loading of Platinum group metal (PGM) for stoichiometric natural gas vehicle (NGV) emission control. Flow reactor results show that a combination of a lean/rich modulated feed and spinel addition gives enhanced methane and NO conversions compared to a steady-state feed having the same overall composition. Washcoated catalysts – PGM-only, spinel-only, PGM + spinel – were compared over a wide range of operating conditions. The results show a decrease in the methane conversion light-off temperature of up to 85 °C for an application-relevant feed (CH 4 + NO + H 2 + CO + O 2 + H 2 O + CO 2 ) while a moderate 40 °C decrease was observed for a simple feed (CH 4 + O 2 + H 2 O + CO 2 ). In the absence of spinel the modulation enhancement is negatively impacted at high methane conversion (> 80 %). The data show that the O 2 storage and release property of the spinel is needed to fully exploit the modulation enhancement. The mechanism responsible for the enhancement is linked to suppression of O 2 inhibition on the methane oxidation rate near the stoichiometric neutral point (λ = 1). Sufficiently fast cycling achieves a balance between a metallic and oxidic precious metal crystallites favorable for methane activation. The addition of spinel moves this balance closer to the λ = 1 feed, enabling a high oxidation efficiency with lower byproduct NH 3 selectivity. Enhancement in the NO conversion follows the methane conversion due to an easier NO reduction under the slightly rich of stoichiometric feed. Comparison of the PGM + spinel catalysts to PGM-only catalysts shows that the addition of spinel in combination with modulation can achieve the same activity with a lower PGM loading.

03 NATURAL GAS↗

Ceria-based nanoflake arrays integrated on 3D cordierite honeycombs for efficient low-temperature diesel oxidation catalyst

A new, surfactant-free hydrothermal method has been developed for the growth of CeO 2 -based nanoflake arrays onto three-dimensional-channeled cordierite honeycomb substrates. Herein, a leaching-crystallization mechanism was proposed where the hydrothermal reaction, only involving cerium nitrate and water, leached the cordierite surface slightly and induced the formation of CeO 2 nanoparticles subsequently. Further continued reaction reincorporated Al and Si atoms leached from cordierite into CeO 2 , finally recrystallizing Ce-Al-Si composite nanoflake structures. Here, by using atomic layer deposition process, well-dispersed, size-controlled Pt nanoparticles were uniformly decorated on the CeO 2 -based nanoflakes to form the Pt/ CeO 2 nano-array-based monolithic catalyst. Despite 5-50 times reduction in the active material usage compared with the traditional wash-coated catalyst, the Pt/CeO 2 nano-array monolithic catalyst exhibited good catalytic oxidation activities over various individual gases, such as propylene, propane, CO, and NO oxidation, with 90% conversion efficiencies at temperatures below 200 °C. Under the simulated exhaust condition of low-temperature diesel combustion (LTC-D) developed by US DRIVE, the monolithic catalyst with low Pt loading (˜1 g/l) exhibits 90% conversion of catalytic oxidation over CO and hydrocarbonsat temperatures as low as ˜180 °C, much superior to the performance of traditional washcoated catalysts.

36 MATERIALS SCIENCE↗

Tungstenocene-grafted silica catalysts for the selective epoxidation of alkenes

In this study, tungstenocene(IV) dichloride was successfully deposited and grafted on the surface of a commercially-available non-ordered silica support via either a liquid-phase or a dry impregnation approach. After a high-temperature calcination step, two W(VI)-grafted silica catalysts, with a metal loading around 1.2–1.7 wt.%, were obtained. They were fully characterized by physisorption and spectroscopic techniques, which evidenced well-dispersed tungsten oxide polyoxo cluster sites, for the catalyst prepared via liquid-phase grafting, and evenly dispersed larger monoclinic tungsten(VI) oxide aggregates, for the catalyst prepared via dry impregnation, respectively. Both W/SiO 2 solids showed moderate to good conversion values in the epoxidation of (R)-(+)-limonene and methyl oleate (up to 68%), in the presence of aqueous hydrogen peroxide, with good selectivity to the desired epoxides (63% and 78%, respectively). Lastly, the heterogeneous character of the most interesting W/SiO 2 catalyst prepared via dry impregnation was confirmed by a hot centrifugation test and by an extended recovery and reuse of the solid in six catalytic runs.

36 MATERIALS SCIENCE↗

Solar reduction of carbon dioxide on copper-tin electrocatalysts with energy conversion efficiency near 20%

Abstract Copper catalysts modified with tin have been demonstrated to be selective for the electroreduction of carbon dioxide to carbon monoxide. However, such catalysts require the precise control of tin loading amount. Here, we develop a copper/tin-oxide catalyst with dominant tin oxide surface being formed via a spontaneous exchange reaction between sputtered tin and copper oxide. Even though the surface of this catalyst is tin-rich, it achieves an excellent performance towards carbon monoxide production in a flow cell. This contrasts with copper/tin-oxide prepared via atomic layer deposition since it yields selectivity towards carbon monoxide only on a copper-rich surface. Mechanism studies reveal that the tin sites on the tin-rich copper/tin-oxide surface achieve a suitable binding with adsorbed carbon monoxide under the presence of copper. Powered by a triple-junction solar cell, the copper/tin-oxide based electrolyzer sets a new benchmark solar-to-chemical energy conversion efficiency of 19.9 percent with a Faradaic efficiency of 98.9 percent towards carbon monoxide under simulated standard air mass 1.5 global illumination.

14 SOLAR ENERGY↗

Organocatalytic Upgrading of Furfural and 5-Hydroxymethyl Furfural to C 10 and C 12 Furoins with Quantitative Yield and Atom-Efficiency

There is increasing interest in the upgrading of C 5 furfural (FF) and C 6 5-hydroxymethyl furfural (HMF) into C 10 and C 12 furoins as higher energy-density intermediates for renewable chemicals, materials, and biofuels. This work utilizes the organocatalytic approach, using the in situ generated N,S-heterocyclic carbene catalyst derived from thiazolium ionic liquids (ILs), to achieve highly efficient self-coupling reactions of FF and HMF. Specifically, variations of the thiazolium IL structure have led to the most active and efficient catalyst system of the current series, which is derived from a new thiazolium IL carrying the electron-donating acetate group at the 5-ring position. For FF coupling by this IL (0.1 mol %, 60 °C, 1 h), when combined with Et 3 N, furoin was obtained in >99% yield. A 97% yield of the C 12 furoin was also achieved from the HMF coupling by this catalyst system (10 mol % loading, 120 °C, 3 h). On the other hand, the thiazolium IL bearing the electron-withdrawing group at the 5-ring position is the least active and efficient catalyst. The mechanistic aspects of the coupling reaction by the thiazolium catalyst system have also been examined and a mechanism has been proposed.

09 BIOMASS FUELS↗

Platinum Deposited Nitrogen-Doped Vertically Aligned Carbon Nanofibers as Methanol Tolerant Catalyst for Oxygen Reduction Reaction with Improved Durability

Nitrogen doping in carbon materials can modify the employed carbon material’s electronic and structural properties, which helps in creating a stronger metal-support interaction. In this study, the role of nitrogen doping in improving the durability of Pt catalysts supported on a three-dimensional vertically aligned carbon nanofiber (VACNF) array towards oxygen reduction reaction (ORR) was explored. The nitrogen moieties present in the N-VACNF enhanced the metal-support interaction and contributed to a reduction in the Pt particle size from 3.1 nm to 2.3 nm. The Pt/N-VACNF catalyst showed better durability when compared to Pt/VACNF and Pt/C catalysts with similar Pt loading. DFT calculations validated the increase in the durability of the Pt NPs with an increase in pyridinic N and corroborated the molecular ORR pathway for Pt/N-VACNF. Moreover, the Pt/N-VACNF catalyst was found to have excellent tolerance towards methanol crossover.

Elangovan, Ayyappan↗

MoS 2 nanosheet integrated electrodes with engineered 1T-2H phases and defects for efficient hydrogen production in practical PEM electrolysis

Low electrical conductivity and poor accessibility of MoS 2 reaction sites raise great challenges in maximizing the triple-phase-boundary (TPB) sites of MoS 2 -based electrodes and minimizing ohmic losses for efficient hydrogen evolution reaction (HER) in practical proton exchange membrane (PEM) water electrolysis. Herein, we report a scalable hydrothermal approach to fabricate ionomer-free integrated electrodes with engineered 1 T-2 H heterophase and defect-rich MoS 2 nanosheets (MoS 2 NSs) in-situ grown onto the carbon fiber paper (CFP). With an ultralow loading of 0.14 mg/cm 2 , a small voltage of 2.25 V was obtained at 2000 mA/cm 2 in a practical cell with Nafion115 membrane, which outperforms all previously reported high-loading non-precious catalyst-based electrodes. Impressively, it shows 44 times higher mass activity than a high-loading and ionomer-mixed MoS 2 assemblies electrode. Furthermore, this work builds a bridge from catalyst optimization to electrode fabrication and provides a promising direction for improving intrinsic catalytic activity, electrode conductivity and stability for practical PEM water electrolysis.

1T-2H heterophase↗

Favorable Core/Shell Interface within Co 2 P/Pt Nanorods for Oxygen Reduction Electrocatalysis

Here, nanostructures with nonprecious metal cores and Pt ultrathin shells are recognized as promising catalysts for oxygen reduction reaction (ORR) to enhance Pt efficiency through core/shell interfacial strain and ligand effects. However, core/shell interaction within a real catalyst is complex and due to the presence of various interfaces in all three dimensions is often oversimply interpreted. Using Co 2 P/Pt core/shell structure as a model catalyst, we demonstrate, through density functional theory (DFT) calculations that forming Co 2 P(001)/Pt(111) interface can greatly improve Pt energetics for ORR, while Co 2 P(010)/Pt(111) is highly detrimental to ORR catalysis. We develop a seed-mediated approach to core/shell Co 2 P/Pt nanorods (NRs) within which Co 2 P(001)/Pt(111) interface is selectively expressed over the side facets and the undesired Co 2 P(010)/Pt(111) interface is minimized. The resultant Co 2 P/Pt NRs are highly efficient in catalyzing ORR in acid, superior to benchmark CoPt alloy and Pt nanoparticle catalyst. As the first example of one-dimensional (1D) core/shell nanostructure with an ultrathin Pt shell and a nonprecious element core, this strategy could be generalized to develop ultralow-loading precious-metal catalysts with favorable core/shell interactions for ORR and beyond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Methane Conversion to Ethylene and Aromatics on PtSn Catalysts

Pt and PtSn catalysts supported on SiO 2 and H-ZSM-5 were studied for methane conversion under nonoxidative conditions. Addition of Sn to Pt/SiO 2 increased the turnover frequency for production of ethylene by a factor of 3, and pretreatment of the catalyst at 1123 K reduced the extent of coke formation. Pt and PtSn catalysts supported on H-ZSM-5 zeolite were prepared to improve the activity and selectivity to non-coke products. Ethylene formation rates were 20 times faster over a PtSn(1:3)/H-ZSM-5 catalyst with SiO 2 :Al 2 O 3 = 280 in comparison to those over PtSn(3:1)/SiO 2 . H-ZSM-5-supported catalysts were also active for the formation of aromatics, and the rates of benzene and naphthalene formation were increased by using more acidic H-ZSM-5 supports. These catalysts operate through a bifunctional mechanism, in which ethylene is first produced on highly dispersed PtSn nanoparticles and then is subsequently converted to benzene and naphthalene on Brønsted acid sites within the zeolite support. The most active and stable PtSn catalyst forms carbon products at a rate, 2.5 mmol of C/((mol of Pt) s), which is comparable to that of state-of-the-art Mo/H-ZSM-5 catalysts with same metal loading operated under similar conditions (1.8 mmol of C/((mol of Mo) s)). Scanning transmission electron microscopy measurements suggest the presence of smaller Pt nanoparticles on H-ZSM-5-supported catalysts, in comparison to SiO 2 -supported catalysts, as a possible source of their high activity. As a result, a microkinetic model of methane conversion on Pt and PtSn surfaces, built using results from density functional theory calculations, predicts higher coupling rates on bimetallic and stepped surfaces, supporting the experimental observations that relate the high catalytic activity to small PtSn particles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Studies on KIT-6 Supported Cobalt Catalyst for Fischer–Tropsch Synthesis

KIT-6 molecular sieve was used as a support to prepare cobalt catalyst for Fischer-Tropsch synthesis (FTS) using an incipient wetness impregnation method to produce cobalt loadings of 15 and 25 wt%. The catalysts were characterized by BET surface area, X-ray diffraction, scanning transmission election microscopy (STEM), extended X-ray absorption fine spectroscopy and X-ray absorption near edge spectroscopy. The catalytic properties for FTS were evaluated using a 1L CSTR reactor. XRD, pore size distribution, and STEM analysis indicate that the KIT-6 mesostructure remains stable during and after cobalt impregnation and tends to form smaller cobalt particles, probably located inside the mesopores. The mesoporous KIT-6 exhibited a slightly higher cobalt dispersion compared to amorphous SiO{sub 2} supported catalyst. With the higher Co loading (25 wt%) on KIT-6, partial structural collapse was observed after the FTS reaction. Compared to an amorphous SiO{sub 2} supported cobalt catalyst, KIT-6 supported cobalt catalyst displayed higher methane selectivity at a similar Co loading, likely due to diffusion effects.

01 COAL, LIGNITE, AND PEAT↗

Low cost modular plasma system for reforming of natural gas

The initial aim of this project was to develop a low-cost compact, modularly scalable, point of use, on demand production system for the reforming of natural gas (NG) into products such as acetylene, hydrogen and other related hydrocarbons. Based on a pulsed dielectric barrier discharge (DBD), the fast rising voltage pulses produced by the system causes the dielectric breakdown of the gas to lag behind the rapid voltage increase so that a voltage greater than the static breakdown voltage of the gas, called an overvoltage, is briefly attained. The century long commercial use of the DBD discharge to push the highly endothermic oxygen to ozone reaction served as an additional motivation. The project meets the recommendations of the National Research Council 2007 report on plasma science for a greater investment in low temperature plasma science and engineering. An important finding is that the method investigated has a high specific energy requirement (SER) of the order of 1,000 to 5,000 kWh per kg of hydrogen, and a corresponding low efficiency of only ~0.1 to 0.5% of converting electrical into chemical (ΔH, ΔG) energy. This compares unfavorably with 52 kWh/kgH 2 required for NG thermal plasma reforming, or a pulsed spark discharge, Lotfalipour et. al, and Gao et. al. (For comparison electrolysis of water into hydrogen and oxygen gas requires only 45 to 80kWh/kgH 2 ). This project garnered data with different reactor configurations, materials, gases and mixtures including NG, methane, hydrogen, propane, argon, nitrogen and air, gap sizes ranging from 0.5 to 4.1 mm, electrode areas from 5 to 460 cm, voltages to 27 kV, pulse frequencies to 20 kHz and peak currents into the hundreds of amperes, temperatures to 625 °C and pressures from 15 mbar to 2 bar. An SRS 300 residual gas analyzer (RGA) yielded quadrupole mass spectrometry (QMS) data on the reformate. To analyze the data we extended the public domain software OpenChrom®, Wenig, to QMS data, yielding accurate identification and quantitative data on reformate products. This extension of OpenChrom® is applicable beyond this project and is a significant contribution to the general community of researchers. The documentation is available on the internet, see Whitlock, and a copy has been appended to this report. The main product of methane and natural gas plasma reforming is hydrogen, constituting ~90% of the products, followed by 1% to 10% ethane, propane, ethylene, acetylene and isobutene. Neopentane, propene, butane and pentane constitute less than 1 % of product. Adding a nickel catalyst increases the selectivity for hydrogen. Carbon nanosheets (graphene), a product of commercial interest, were synthesized by plasma reforming of acetylene at low pressure. The reformate analysis shows hat saturated and branched hydrocarbons are favored compared with unsaturated and linear hydrocarbons. For example, ethane, propane, iso-butane, 2-methyl butane, and 2-methyl pentane are produced in higher amounts compared with unsaturated and linear components. At low pressure acetylene and ethylene production rate is higher and propane production lower. We developed a recirculating system in which hydrogen is removed through a permeable membrane as fast as it is being produced by the reactor and the remaining products are recirculated at a high flow rate of several liters per minute. This keeps the concentration of H 2 in the reactor low, while achieving a total output concentration of 79%, high enough for pressure swing adsorption to be used for further purification. The recirculating system could be used with other gas reforming technologies. We report on four different reactors,1) a spark discharge reactor, 2) a standard DBD cylindrical reactor, 3) a small DBD reactor where catalyst powder can be quickly loaded onto a carrier to investigate the effect of the plasma on the catalyst and the effectiveness of the of the catalyst in promoting gas reformation and 4) a configurable DBD reactor to study the performance effects of dielectric selection, electrode gap distance, and electrode/dielectric interface on plasma reactor operation. This project achieved a commercializable 1kW plasma system including reactors a plasma pulse generator and a gas supply module.

03 NATURAL GAS↗

3D pore analysis of gasoline particulate filters using X-ray tomography: impact of coating and ash loading

Since particulate emissions control technologies are dependent on filtration technologies, development of porous materials with optimized pore structures is crucial to improve filtration efficiency and pressure drop across filters. Despite increasing attention to 3D measurements of porous materials, there are few reports of pore structure investigations of diesel/gasoline particulate filters (D/GPFs) using 3D visualization techniques. Here, GPF 3D pore structures were examined using X-ray tomography (XRT) to identify the impacts of catalyst coating or ash loading. Voxel resolution of 2.93 mu m made it impossible to distinguish coating or ash materials from the cordierite substrate or to recognize smaller pores than the voxel resolution. However, pores up to 200 mu m, which are responsible for the most pore volume, were successfully analyzed. Coating and ash loading resulted in lowering average pore diameter, total porosity, and open porosity, as the peak density of pore diameter at 60 mu m decreased, while pores below 20 mu m increased. Also, the visualized closed pores, which were homogeneously distributed throughout the bare filter, tended to get larger from inlet to outlet sides and more likely to be on the surface inlet due to coating and ash loading, indicating gas pathways originally existing in open pores were blocked due to coating and ash loading, leading to increased pressure drop. The ash impact was found to be more noticeable on mid and back positions than on front position. In addition, the investigation of areal porosity along the direction of gas flow suggested that while ash penetration could reach the outlet side as noted from increased closed pore population, most ash particles would be contained up to 150 mu m. Lastly, the 2D crosscut microscopic analysis that requires destructive procedures with the limited examination area could provide underestimation of ash penetration, whereas the 3D XRT analysis seems to provide more accurate information of pore structure changes due to ash loading at different locations.

36 MATERIALS SCIENCE↗

A Comparative Study of Ethanol Upgrading to Butadiene Over Rare Earth Elements Incorporated in Dealuminated Beta Zeolites

Copper and rare earth element-containing dealuminated Beta zeolites (CuREE/deAlBeta) are promising catalysts for the conversion of ethanol to C 3+ olefins en route to sustainable aviation fuel. Product selectivities over CuREE/deAlBeta depend on the identity of the REE. Here, in this study, a suite of La/deAlBeta catalysts of varied La loading are prepared, and their reactivities, selectivities, and apparent C-C coupling kinetics in the cascade reaction between ethanol and acetaldehyde are reported. Ex situ and in situ titrations to quantify Lewis acidic La sites quantify distinct numbers of sites, suggesting a distribution of site types. Across a series of REE/deAlBeta catalysts (REE = Y, La, Lu, Yb, Gd), the selectivity to secondary products correlates with the pyridine heats of adsorption at REE Lewis acid sites. The turnover frequency (per Lewis acid site) for C–C coupling was similar across the series of REE/deAlBeta catalysts. Y/deAlBeta and La/deAlBeta, which have the most disparate secondary product selectivities, had similar kinetics for C–C coupling. These findings demonstrate the complexity of quantifying active sites in REE/deAlBeta zeolites, and the sensitivity of the selectivity, but not the reactivity for C–C coupling, to the identity of the REE atom in REE/deAlBeta zeolites.

alcohol upgrading↗

Role of the metal-support interface in the hydrodeoxygenation reaction of phenol

In this paper, the effect of interfacial sites between Pd particles and Nb 2 O 5 species is investigated by testing a series of Pd-Nb 2 O 5 /SiO 2 catalysts with different niobium loadings for the HDO reaction of phenol in the gas phase. Important differences in the selectivity to deoxygenated product were observed depending on the presence of niobium oxide close to Pd particles, which reveals the key role of the type of active phase in the control of reaction steps. It was found that Pd/SiO 2 catalyst promotes hydrogenation pathways, producing cyclohexanone as the major product. For Pd-Nb 2 O 5 /SiO 2 catalyst containing a Nb/Pd molar ratio of 0.5, a sharp increase in the selectivity to benzene is observed (7.5-fold). Increasing the Nb/Pd molar ratio, the formation of benzene is enhanced. The results showed that the Pd-Nb 2 O 5 interface, composed by an oxophilic oxide in the perimeter of the metal particle, is responsible for the activation of the Csingle bondO bond, promoting the deoxygenation reaction.

09 BIOMASS FUELS↗

Single Metal Atom Catalysts Prepared by Diluted Atomic Layer Deposition

The scalable and facile preparation of single-atom catalysts remains a critical challenge. Here, in this study, we introduce diluted atomic layer deposition (DALD), a unique approach for synthesizing supported metal catalysts with precisely tunable loadings. Unlike conventional metal deposition by ALD which uses pure metal precursors, DALD employs a diluted precursor mixture, combining organometallic precursors with the corresponding free ligand in controlled ratios. The method enables precise control over metal loadings, allowing the synthesis of structures ranging from nanoparticles to isolated single atoms, as exemplified by Ir, Rh, and Pt on high-surface-area γ-Al 2 O 3 . With its inherent simplicity and exceptional efficiency in metal precursor utilization, DALD represents a highly scalable strategy, unlocking opportunities for integrating single-atom catalysts into industrial processes.

36 MATERIALS SCIENCE↗

Uncovering the active sites and demonstrating stable catalyst for the cost-effective conversion of ethanol to 1-butanol

We report the recent emergence of a robust renewable ethanol industry has provided a sustainable platform molecule toward the production of value-added chemicals and fuels; what is lacking now are viable conversion processes from ethanol that can displace the current production pathways from non-renewable pathways. Here in the work, we demonstrate the highly selective conversion of ethanol to higher alcohols over low copper loaded MgAl mixed oxide catalysts, with 50% improvement in higher alcohol yields over the current state of the art. At these copper concentrations, atomically dispersed Cu +1 were found to be stable even at highly reductive conditions and highly active towards higher alcohol products (e.g. butanol, hexanol) while suppressing side reaction pathways and leading to extended lifetimes of over 150 hours time on stream. Technoeconomic analysis conducted based on these experimental results demonstrate that this catalytic system is cost-competitive with the conventional process. This marks significant progress in the development of Guerbet coupling of ethanol as a viable renewable process and offers a pathway toward sustainable chemical and fuel production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Meso-porous α-Fe{sub 2}O{sub 3} thin films synthesized via the sol-gel process for light-driven water oxidation

This work reports a facile and cost-effective method for synthesizing photoactive α-Fe{sub 2}O{sub 3} films as well as their performances when used as photoanodes for water oxidation. Transparent α-Fe{sub 2}O{sub 3} meso-porous films were fabricated by template-directed sol-gel chemistry coupled with the dip-coating approach, followed by annealing at various temperatures from 350 degrees C to 750 degrees C in air. α-Fe{sub 2}O{sub 3} films were characterized by X-ray diffraction, XPS, FE-SEM and electrochemical measurements. The photoelectrochemical performance of α-Fe{sub 2}O{sub 3} photoanodes was characterized and optimized through the deposition of Co-based co-catalysts via different methods (impregnation, electro-deposition and photo-electro-deposition). Interestingly, the resulting hematite films heat-treated at relatively low temperature (500 degrees C), and therefore devoid of any extrinsic dopant, achieve light-driven water oxidation under near-to-neutral (pH = 8) aqueous conditions after decoration with a Co catalyst. The onset potential is 0.75 V vs. the reversible hydrogen electrode (RHE), thus corresponding to 450 mV light-induced under potential, although modest photocurrent density values (40 μAcm{sup -2}) are obtained below 1.23 V vs. RHE. These new materials with a very large interfacial area in contact with the electrolyte and allowing for a high loading of water oxidation catalysts open new avenues for the optimization of photo-electrochemical water splitting. (authors)

08 HYDROGEN↗