Search NASA⌕ Search

SEARCH · Search NASA

Results for “cell integration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Advances in Single and Multijunction III-V Photovoltaics on Silicon for Space Power

A collaborative research effort at MIT, Ohio State University and NASA has resulted in the demonstration of record quality gallium arsenide (GaAs) based single junction photovoltaic devices on silicon (Si) substrates. The ability to integrate highly efficient, radiation hard III-V based devices on silicon offers the potential for dramatic reductions in cell mass (approx.2x) and increases in cell area. Both of these improvements offer the potential for dramatic reductions in the cost of on-orbit electrical power. Recently, lattice matched InGaP/GaAs and metamorphic InGaP/InGaAs dual junction solar cells were demonstrated by MBE and OMVPE, respectively. Single junction GaAs on Si devices have been integrated into a space flight experiment (MISSES), scheduled to be launched to the International Space Station in March of 2005. I-V performance data from the GaAs/Si will be collected on-orbit and telemetered to ground stations daily. Microcracks in the GaAs epitaxial material, generated because of differences in the thermal expansion coefficient between GaAs and Si, are of concern in the widely varying thermal environment encountered in low Earth orbit. Ground based thermal life cycling (-80 C to + 80 C) equivalent to 1 year in LEO has been conducted on GaAs/Si devices with no discernable degradation in device performance, suggesting that microcracks may not limit the ability to field GaAs/Si in harsh thermal environments. Recent advances in the development and testing of III-V photovoltaic devices on Si will be presented.

Wilt, David M.↗

Thermoviscoplastic analysis of fibrous periodic composites using triangular subvolumes

The nonlinear viscoplastic behavior of fibrous periodic composites is analyzed by discretizing the unit cell into triangular subvolumes. A set of these subvolumes can be configured by the analyst to construct a representation for the unit cell of a periodic composite. In each step of the loading history, the total strain increment at any point is governed by an integral equation which applies to the entire composite. A Fourier series approximation allows the incremental stresses and strains to be determined within a unit cell of the periodic lattice. The nonlinearity arising from the viscoplastic behavior of the constituent materials comprising the composite is treated as fictitious body force in the governing integral equation. Specific numerical examples showing the stress distributions in the unit cell of a fibrous tungsten/copper metal matrix composite under viscoplastic loading conditions are given. The stress distribution resulting in the unit cell when the composite material is subjected to an overall transverse stress loading history perpendicular to the fibers is found to be highly heterogeneous, and typical homogenization techniques based on treating the stress and strain distributions within the constituent phases as homogeneous result in large errors under inelastic loading conditions.

Walker, Kevin P.↗

Thermoviscoplastic analysis of fibrous periodic composites by the use of triangular subvolumes

The non-linear viscoplastic behavior of fibrous periodic composites is analyzed by discretizing the unit cell into triangular subvolumes. A set of these subvolumes can be configured by the analyst to construct a representation for the unit cell of a periodic composite. In each step of the loading history the total strain increment at any point is governed by an integral equation which applies to the entire composite. A Fourier series approximation allows the incremental stresses and strains to be determined within a unit cell of the periodic lattice. The non-linearity arising from the viscoplastic behavior of the constituent materials comprising the composite is treated as a fictitious body force in the governing integral equation. Specific numerical examples showing the stress distributions in the unit cell of a fibrous tungsten/copper metal-matrix composite under viscoplastic loading conditions are given. The stress distribution resulting in the unit cell when the composite material is subjected to an overall transverse stress loading history perpendicular to the fibers is found to be highly heterogeneous, and typical homogenization techniques based on treating the stress and strain distributions within the constituent phases as homogeneous result in large errors under inelastic loading conditions.

Walker, Kevin P.↗

Refinement Of Hexahedral Cells In Euler Flow Computations

Topologically Independent Grid, Euler Refinement (TIGER) computer program solves Euler equations of three-dimensional, unsteady flow of inviscid, compressible fluid by numerical integration on unstructured hexahedral coordinate grid refined where necessary to resolve shocks and other details. Hexahedral cells subdivided, each into eight smaller cells, as needed to refine computational grid in regions of high flow gradients. Grid Interactive Refinement and Flow-Field Examination (GIRAFFE) computer program written in conjunction with TIGER program to display computed flow-field data and to assist researcher in verifying specified boundary conditions and refining grid.

Melton, John E.↗

Proceedings of the 22nd Project Integration Meeting

This report describes progress made by the Flat-Plate Solar Array Project during the period January to September 1983. It includes reports on silicon sheet growth and characterization, module technology, silicon material, cell processing and high-efficiency cells, environmental isolation, engineering sciences, module performance and failure analysis and project analysis and integration. It includes a report on, and copies of visual presentations made at the 22nd Project Integration Meeting held at Pasadena, California, on September 28 and 29, 1983.

Source record↗

Improved reversible coulometer cell

Cell operates either as timer or current-time integrating device in any physical orientation with better than 2 percent accuracy over temperature range of 283 K to 398 K, with input current range from few microamperes to approximately 1000 microamperes over time period of 1 sec to several hours.

Boettcher, G. E.↗

Distribution effectiveness for space radiation dosimetry

A simplified risk basis and a theory of hematological response are presented and applied to the problem of dosimetry in the manned space program. Unlike previous studies, the current work incorporates radiation exposure distribution effects into its definition of dose equivalent. The fractional cell lethality model for prediction of hematological response is integral in the analysis.

Wilson, J. W.↗

Computer modeling of a two-junction, monolithic cascade solar cell

The theory and design criteria for monolithic, two-junction cascade solar cells are described. The departure from the conventional solar cell analytical method and the reasons for using the integral form of the continuity equations are briefly discussed. The results of design optimization are presented. The energy conversion efficiency that is predicted for the optimized structure is greater than 30% at 300 K, AMO and one sun. The analytical method predicts device performance characteristics as a function of temperature. The range is restricted to 300 to 600 K. While the analysis is capable of determining most of the physical processes occurring in each of the individual layers, only the more significant device performance characteristics are presented.

Lamorte, M. F.↗

Rotor systems research aircraft /RSRA/ rotor force and moment measurement system

The two Rotor Systems Research Aircraft (RSRA) are flight vehicles with unique measurement capabilities. The primary goal of the RSRA is direct measurement of rotor forces and moments in flight. This is accomplished through a rotor force and moment measurement system comprised of load cells and/or hydro-pneumatic isolator units which are integral to the aircraft structure. Due to structural flexibility, the aircraft must undergo a physical calibration. A static calibration of the first RSRA has been completed, and data analysis has progressed through determination of a linear calibration algorithm. Design, development, and operation of the RSRA rotor force and moment measurement system and the Static Calibration Facility are described, and results of the calibration are presented.

Burks, J. S.↗

Turbidity very near the critical point of methanol-cyclohexane mixtures

The turbidity of a critical mixture of methanol and cyclohexane has been measured extremely close to the consolute point. The data span the reduced-temperature range between 10 to the -7th and 10 to the -3d, which is two decades closer to Tc than previous measurements. In this temperature range, the turbidity varies approximately as 1nt, as expected from the integrated form for Ornstein-Zernike scattering. A thin cell (200-micron optical path) with a very small volume (0.08 ml) was used to avoid multiple scattering. A carefully controlled temperature history was used to mix the sample and to minimize the effects of critical wetting layers. The data are consistent with a correlation-length amplitude of 3.9 plus or minus 1.0 A, in agreement with the value 3.5 A calculated from two-scale-factor universality and heat-capacity data from the literature.

Kopelman, R. B.↗

Periodic binary sequence generators: VLSI circuits considerations

Feedback shift registers are efficient periodic binary sequence generators. Polynomials of degree r over a Galois field characteristic 2(GF(2)) characterize the behavior of shift registers with linear logic feedback. The algorithmic determination of the trinomial of lowest degree, when it exists, that contains a given irreducible polynomial over GF(2) as a factor is presented. This corresponds to embedding the behavior of an r-stage shift register with linear logic feedback into that of an n-stage shift register with a single two-input modulo 2 summer (i.e., Exclusive-OR gate) in its feedback. This leads to Very Large Scale Integrated (VLSI) circuit architecture of maximal regularity (i.e., identical cells) with intercell communications serialized to a maximal degree.

Perlman, M.↗

The use of computer graphic simulation in the development of robotic systems

This paper describes the use of computer graphic simulation techniques to resolve critical design and operational issues for robotic systems. Use of this technology will result in greatly improved systems and reduced development costs. The major design issues in developing effective robotic systems are discussed and the use of ROBOSIM, a NASA developed simulation tool, to address these issues is presented. Three representative simulation case studies are reviewed: off-line programming of the robotic welding development cell for the Space Shuttle Main Engine (SSME); the integration of a sensor to control the robot used for removing the Thermal Protection System (TPS) from the Solid Rocket Booster (SRB); and the development of a teleoperator/robot mechanism for the Orbital Maneuvering Vehicle (OMV).

Fernandez, K.↗

The use of computer graphic simulation in the development of robotic systems

This paper describes the use of computer graphic simulation techniques to resolve critical design and operational issues for robotic systems. Use of this technology will result in greatly improved systems and reduced development costs. The major design issues in developing effective robotic systems are discussed and the use of ROBOSIM, a NASA developed simulation tool, to address these issues is presented. Three representative simulation case studies are reviewed: off-line programming of the robotic welding development cell for the Space Shuttle Main Engine (SSME); the integration of a sensor to control the robot used for removing the Thermal Protection System (TPS) from the Solid Rocket Booster (SRB); and the development of a teleoperator/robot mechanism for the Orbital Maneuvering Vehicle (OMV).

Fernandez, Ken↗

ECUT (Energy Conversion and Utilization Technologies) program: Biocatalysis Project

Fiscal year 1987 research activities and accomplishments for the Biocatalysis Project of the U.S. Department of Energy, Energy Conversion and Utilization Technologies (ECUT) Division are presented. The project's technical activities were organized into three work elements. The Molecular Modeling and Applied Genetics work element includes modeling and simulation studies to verify a dynamic model of the enzyme carboxypeptidase; plasmid stabilization by chromosomal integration; growth and stability characteristics of plasmid-containing cells; and determination of optional production parameters for hyper-production of polyphenol oxidase. The Bioprocess Engineering work element supports efforts in novel bioreactor concepts that are likely to lead to substantially higher levels of reactor productivity, product yields, and lower separation energetics. The Bioprocess Design and Assessment work element attempts to develop procedures (via user-friendly computer software) for assessing the economics and energetics of a given biocatalyst process.

Source record↗

Improved Ferroelectric Memories With Nondestructive Readout

Ferroelectric memories with enhanced photoresponse leading to improved nondestructive optoelectronic readout and lower power demand proposed. Memories improved versions of devices described in "Rapid, Nondestructive Readout From Ferroelectric Memory" (NPO-18551). In proposed application, array of nonvolatile ferroelectric memory cells fabricated by standard very-large-scale integrated-circuit techniques and flip-bonded onto similarly fabricated array of semiconductor lasers, {see "Optically Addressable, Ferroelectric Memory With NDRO" (NPO-18573)}.

Thakoor, Sarita↗

Research Help

The Electrosynthesis Co. Inc.'s Electrocinerator System integrates a highly effective air scrubber with an electrochemical cell to provide an apparatus capable of destroying virtually all toxic chemicals and airborne bacteria. Project (funded by DOD) is prospective means of decontaminating airborne chemicals and biological warfare agents. Also has broad civil use applicable to hospitals for destruction of airborne viruses and bacteria, and industrial use for elimination of toxic solvent vapors and malodorous emissions.

Source record↗

Active pixel sensor having intra-pixel charge transfer with analog-to-digital converter

An imaging device formed as a monolithic complementary metal oxide semiconductor Integrated circuit in an industry standard complementary metal oxide semiconductor process, the integrated circuit including a focal plane array of pixel cells, each one of the cells including a photogate overlying the substrate for accumulating photo-generated charge in an underlying portion of the substrate, a readout circuit including at least an output field effect transistor formed in the substrate, and a charge coupled device section formed on the substrate adjacent the photogate having a sensing node connected to the output transistor and at least one charge coupled device stage for transferring charge from the underlying portion of the substrate to the sensing node and an analog-to-digital converter formed in the substrate connected to the output of the readout circuit.

Fossum, Eric R.↗

Active pixel sensor with intra-pixel charge transfer

An imaging device formed as a monolithic complementary metal oxide semiconductor integrated circuit in an industry standard complementary metal oxide semiconductor process, the integrated circuit including a focal plane array of pixel cells, each one of the cells including a photogate overlying the substrate for accumulating photo-generated charge in an underlying portion of the substrate, a readout circuit including at least an output field effect transistor formed in the substrate, and a charge coupled device section formed on the substrate adjacent the photogate having a sensing node connected to the output transistor and at least one charge coupled device stage for transferring charge from the underlying portion of the substrate to the sensing node.

Fossum, Eric R.↗