SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
System can transmit range-indicating pseudonoise (PN) codes and simultaneously transmit auxiliary information as binary data at a rate at least on order of pseudonoise chipping rate. PN code is modulated by data stream with relatively low bit rate. Data stream with high bit rate can be transmitted in same frequency band as PN ranging code.
Improved design for modulator and demodulator in offset-quaternary-phase-key-shifting (OQPSK) communication system enables receiver to resolve ambiguity in estimated phase of received signal. Features include unique-code-word modulation and detection and digital implementation of Costas loop in carrier-recovery subsystem. Enchances performance of carrier-recovery subsystem, reduces complexity of receiver by removing redundant circuits from previous design, and eliminates dependence of timing in receiver upon parallel-to-serial-conversion clock.
A computer code was developed to evaluate the space radiation environment encountered by geocentric satellites. The Short Orbital Flux Integration Program (SOFIP) is a compact routine of modular compositions, designed mostly with structured programming techniques in order to provide core and time economy and ease of use. The program in its simplest form produces for a given input trajectory a composite integral orbital spectrum of either protons or electrons. Additional features are available separately or in combination with the inclusion of the corresponding (optional) modules. The code is described in detail, and the function and usage of the various modules are explained. A program listing and sample outputs are attached.
Ability to lock onto signal increased with minimal equipment. Technique proposed to improve acquisition of spread-spectrum (pseudonoise) coded signal modulated by digital data signal. Divides correlation time into subintervals, integrates over subintervals, passes integrator outputs through square-law detectors, and adds detector outputs over all subintervals to reach decision regarding detection of code. Reduces effect of data-bit transitions at price of non-coherent-combining loss.
Gigabit-per-second communications have been a desired target for future NASA Earth science missions, and for potential manned lunar missions. Frequency bandwidth at S-band and X-band is typically insufficient to support missions at these high data rates. In this paper, we present the results of a 1 Gbps 32-QAM end-to-end experiment at Ka-band using a reconfigurable Field Programmable Gate Array (FPGA) baseband modulator board. Bit error rate measurements of the received signal using a software receiver demonstrate the feasibility of using ultra-high data rates at Ka-band, although results indicate that error correcting coding and/or modulator predistortion must be implemented in addition. Also, results of the demonstration validate the low-cost, MOS-based reconfigurable modulator approach taken to development of a high rate modulator, as opposed to more expensive ASIC or pure analog approaches.
Digital telemetry has supplanted analog telemetry for deep space communications. With digital telemetry, the telecommunications systems design engineer may use error correcting codes. This allows increased error protection at the cost of increased bandwidth. All science telemetry returned from the Voyager and Galileo spacecraft are protected by error correcting codes. Both the modulation and coding of digital telemetry for the deep space channel are considered. The descriptions include relative performance of some competing schemes. However, the treatment given here is, of necessity, cursory. A small class of modulation schemes has proven to be best for the deep space channel. The digital telemetry is either phase-shift-keyed onto a squarewave subcarrier and then phase modulated onto the carrier or the digital telemetry is directly phase modulated onto the carrier.
After a brief introduction on the need for simulation packages for the analysis and design of satellite communications systems, the software tool developed for the European Space Agency (ESA), its main objectives and the design choices made during the development are presented. A very concise description of the available communications and measurement block follows. The ESA standard Telemetry, Tracking and Command (TT&C) system simulator is then introduced along with a description of the ESA standard modulation and coding schemes. As an example, the simulation of the ranging system which is a non-standard communications block, is described in details. Several examples of TT&C simulations outputs are given and compared with measurement results or theoretical approximations, when available. Finally, future developments like the support of advanced modulation schemes and the dynamic satellite link simulation are presented.
Turbo coding using iterative SOVA decoding and M-ary differentially coherent or non-coherent modulation can provide an effective coding modulation solution: (1) Energy efficient with relatively simple SOVA decoding and small packet lengths, depending on BEP required; (2) Low number of decoding iterations required; and (3) Robustness in fading with channel interleaving.
Satellite on-board processing is needed to efficiently service multiple users while at the same time minimizing earth station complexity. The processing satellite receives a wideband uplink at 30 GHz and down-converts it to a suitable intermediate frequency. A multichannel demultiplexer then separates the composite signal into discrete channels. Each channel is then demodulated by bulk demodulators, with the baseband signals routed to the downlink processor for retransmission to the receiving earth stations. This type of processing circumvents many of the difficulties associated with traditional bent-pipe repeater satellites. Uplink signal distortion and interference are not retransmitted on the downlink. Downlink power can be allocated in accordance with user needs, independent of uplink transmissions. This allows the uplink users to employ different data rates as well as different modulation and coding schemes. In addition, all downlink users have a common frequency standard and symbol clock on the satellite, which is useful for network synchronization in time division multiple access schemes. The purpose of this program is to demonstrate the concept of an optically implemented multichannel demultiplexer (MCD). A proof-of-concept (POC) model has been developed which has the ability to receive a 40 MHz wide composite signal consisting of up to 1000 40 kHz QPSK modulated channels and perform the demultiplexing process. In addition a set of special test equipment (STE) has been configured to evaluate the performance of the POC model. The optical MCD is realized as an acousto-optic spectrum analyzer utilizing the capability of Bragg cells to perform the required channelization. These Bragg cells receive an optical input from a laser source and an RF input (the signal). The Bragg interaction causes optical output diffractions at angles proportional to the RF input frequency. These discrete diffractions are optically detected and output to individual demodulators for baseband conversion. Optimization of the MCD design was conducted in order to achieve a compromise between two opposing sources of signal degradation: adjacent channel interference and intersymbol interference. The system was also optimized to allow simple, inexpensive ground stations communications with the MCD. These design goals led to the realization of a POC MCD which demonstrates the demultiplexing function with minimal signal degradation. Performance evaluation results using the STE equipment indicate that the dynamic range of the demultiplexer in the presence of adjacent and multiple channel loading is 40 - 50 dB. Measured bit error rate (BER) probabilities varied from the predicted theoretical results by one dB or less. The performance of the proof-of-concept model indicate that the development of a space qualified optically implemented MCD are feasible. The advantages to such an implementation include reduced size, weight and power and increased reliability when compared with electronic approaches. All of these factors are critical to on-board satellite processors. Further optimization can be conducted which trade ground station complexity and MCD performance to achieve desired system results.
The Universal Space Transponder (UST) is a next generation transponder developed at the Jet Propulsion Laboratory to meet a large variety of telecom, navigation, and radio science needs for future deep-space and near-Earth missions. This paper details the UST software defined radio design and describes how the combination of a modular hardware architecture and in-flight reprogrammability enables a new level of flexibility and expandability for a space transponder. The UST uses common power and digital processing assemblies that can be integrated with a variety of RF modules and is capable of simultaneous, multiband operations with data rates up to 37.5 Mbps RX and 300 Mbps TX. This allows a single radio to support all the direct-to-Earth and relay communication requirements for even complex mission scenarios, reducing the total cost, mass, and power. The discussion includes a description of the current UST engineering models that have been built and tested, as well as details about the next generation capabilities supported by UST, including advanced link coding and modulation, radiometric techniques, and in-radio protocol handling. Details are also presented on RF modules and digital processing in development for radio science and astronomy purposes, including a bistatic radar receiver and broadband planetary emissions receiver. These will demonstrate the ability to integrate low-cost science instruments into the UST architecture, further expanding the versatility of the UST.
Abstract We have developed a modular graphical user interface (GUI)-based program for use in genetic algorithm-based feedback-assisted wavefront shaping. The program uses a class-based structure to separate out the universal modules (e.g. GUI, multithreading, optimization algorithms) and hardware-specific modules (e.g. code for different SLMs and cameras). This modular design makes the program easily adaptable to a wide range of lab equipment, while providing easy access to a GUI, multithreading, and three optimization algorithms (phase-stepping, simple genetic, and microgenetic).
With the increase of interests in the design and deployment of advanced reactor systems, a desire for simulation tools supporting system analysis of reactor operation and safety is rising. Molten salt reactors (MSRs), one of the advanced reactor systems, utilize liquid fused salt fuel as both coolant and fuel. During operation, MSR generates insoluble fission products, including noble metals and gases. The buildup of these species in fuel salt presents safety concerns as they may deposit on surfaces of critical components and produce excessive decay heat, causing the failure of system components. Timely removal of these noble metals and gases would ensure the safe operation of the reactor system. The dynamic nature of salt fuel system, involving the generation, decay, deposition, and extraction of noble metals and gases, calls for robust species transport models to facilitate system analysis and monitoring, and design of efficient species removal components. This paper concentrates on the development of a computational framework for species transport, consisting of multiphase transport model formulation, mass transfer between phases, numerical implementation in MOOSE environment, verification through Method of Manufacture Solutions (MMS) and validation against experimental data from the Molten Salt Reactor Experiment (MSRE). Integrating this framework into the System Analysis Module (SAM) code further enhances SAM’s capabilities for advanced reactor analysis in the future.
In this paper we design and analyze an end-to-endcommunication system between a lander/rover on the surface ofthe lunar South Pole and an Earth station. Various communicationsystems on the lander or rover could be used for the Earthto-Moon communication in both the uplink and downlink direction.To communicate to and from the lander/rover on the lunarSouth Pole, low and/or medium directional antennas onboardthe lander/rover will have to be pointed at low elevation anglesbetween 2 to 10 degrees, thus causing multipath fading effectsdue to reflection of a portion of the transmitted electromagneticwaves from the surface of the Moon. These are not commonlyencountered in traditional deep space communications betweena spacecraft and a ground station.We investigate various design methods and analyze such communicationsystems, in the presence of multipath fading. Wemodel the fading channel based on existing and simulated data.For coherent reception, the acquisition and tracking loop shouldacquire and track incoming carrier phase in presence of Ricianmultipath fading. For this communication system in additionto estimating the received carrier phase, the amplitude of thefading signal should also be estimated, in particular to be used inthe decoder. We consider simple modulation and coding schemesin particular those specified in the CCSDS standards for spaceapplications.After designing various components of the communication system,we use Simulink models to obtain the end-to-end performanceof the communication link under investigation. Basedon the available data, the fading channel can be accuratelymodeled as a Rician fading channel with various Rician parametersdepending on the Earth elevation angle, which alsoaffects the Doppler spread. Therefore, the challenge is todesign a communication system robust in the presence of themultipath fading where the channel conditions change in timeand thus produce fading. In summary, this paper comparespossible communication system designs, performance analysis,and simulations for coded system with/without interleaving withhard/soft decision and with/without channel state information(CSI), over a communication link between a lander/rover at theLunar south pole and a Deep Space Network station in presenceof Rician fading.
Here, in this work, we introduce a novel method to develop whole system digital twins (DTs) for advanced nuclear reactors. This method treats a complex reactor system as a heterogeneous graph: with the system components as different types of graph nodes and their physical interconnections as edges. Based on the heterogeneous graph, a graph neural network combining graph convolution and temporal node attention is developed as the DT, facilitating a comprehensive understanding of the system's dynamic behavior. By utilizing the System Analysis Module (SAM) code for simulating various operational transients, we develop a graph-based database that trains the DT. This DT is characterized by two primary functions: It can infer the entire system's status using sparse node information, and it can predict the progress of transients based on current and historical system information. Our approach is validated through case studies on the Experimental Breeder Reactor II (EBR-II) system and a generic Fluoride-salt-cooled High-temperature Reactor (gFHR), demonstrating the DT's accuracy in forecasting operational transients. The DT's rapid computation capabilities enhance its potential for supporting advanced reactor operations, offering benefits in intelligent simulation, autonomous control, and anomaly detection, paving the way for improved safety analysis and intelligent component health management for advanced reactor systems and reducing their operations and maintenance cost.
The command and telemetry portions of the Telstar system provide necessary support functions for the basic communications experiment and the radiation experiment. By means of the command system, the states of 9 magnetic latching relays in the satellite are controlled from the ground. Commands are sent to the satellite by coded signals modulated on a carrier in the VHF band. The telemetry system also uses a VHF carrier to transmit encoded information from the satellite. Data on 112 items are provided once each minute. This paper discusses the over-all command and telemetry systems and considers the general objectives, system aspects and detailed implementation.
Explorer xvii real time pcm telemetry data processing and display test stand
Network equipment installation at remote sites for Apollo program
Data telemetering to Earth from EGO describing PCM system and special processor for magnetometer data