Search NASA⌕ Search

SEARCH · Search NASA

Results for “commonality”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Assessment of Aeroacoustic Simulations of the High-Lift Common Research Model

This paper presents further validation of PowerFLOWR aeroacoustic simulations of the High-Lift Common Research Model through comparisons with experimental data from a recently completed wind tunnel test. Preliminary time- averaged surface pressure and microphone array data from the experiment are in reasonably good agreement with the simulations, and the slat is shown to be a dominant noise source on this model. The simulations did not predict slat tones that were very prominent in the experiment, but they did capture the broadband component of slat noise in the low-frequency range up to 1 kHz at full scale. Future tests are planned to demonstrate slat noise reduction technology, and simulations are being used to guide this development.

Lockard, David P.↗
NASA NTRS2019

Additional Findings from the Common Research Model Natural Laminar Flow Wind Tunnel Test

An experimental investigation of the Common Research Model with Natural Laminar Flow (CRM-NLF) took place in the National Transonic Facility (NTF) at the NASA Langley Research Center in 2018. The 5.2% scale semispan model was designed using a new natural laminar flow design method, Crossflow Attenuated NLF (CATNLF). CATNLF enables laminar flow on typical transport wings with high sweep and Reynolds number by reshaping the wing airfoils to obtain specific pressure distribution characteristics that control the crossflow growth near the leading edge. The CATNLF method also addresses Tollmien- Schlichting transition, attachment line transition, and Görtler vortices. During the wind tunnel test, data were acquired to address three primary test objectives: validate the CATNLF design method, characterize the NTF laminar flow testing capabilities, and establish best practices for laminar flow wind tunnel testing. The present paper provides both experimental and computational data to understand the CRM-NLF laminar flow characteristics, as well as address the three primary test objectives. The effects of angle of attack and Reynolds number on the CRM-NLF laminar flow extent are studied, and the dominant transition mechanism is evaluated at a variety of test conditions. Critical N-factors are calculated for the NTF environment, and a discussion on best practices for laminar flow wind tunnel testing is provided. The CRM-NLF in the NTF provided initial confirmation of the ability of the CATNLF method to suppress crossflow growth and enable significant extents of laminar flow on transport wings with high sweep and Reynolds numbers.

Lynde, Michelle N.↗
NASA NTRS2019

Wind Tunnel Testing of Active Flow Control on High-Lift Common Research Model

A 10%-scale high-lift version of the Common Research Model (CRM-HL) and an Active Flow Control (AFC) version of the model equipped with a simple-hinged flap (CRM-SHLAFC) were successfully tested. The tests were performed in the 14- by 22-Foot Subsonic Tunnel (14x22) at the NASA Langley Research Center (LaRC). The CRM-HL has a set of 37° inboard and outboard single-element Fowler flaps. The CRM-SHL-AFC has a set of 50° inboard and 55° outboard simple-hinged flaps equipped with integrated modular AFC cartridges on the flap shoulder. Both high-lift configurations share the same 30° slats and engine nacelle. Three new types of AFC devices were examined: the Double-Row Sweeping Jets (DRSWJ), the Alternating Pulsed Jets (APJ), and the High Efficiency Low Power (HELP) actuators. The DRSWJ and the APJ actuators used two rows of unsteady jets, whereas the HELP actuators used a combination of unsteady and steady jets, to overcome strong adverse pressure gradients while minimizing the mass flow usage. Nozzle pressure ratio, mass flow consumption and the power coefficient, which takes account of both supply air pressure and mass flow usage for the actuators, were used for judging the performance efficiency of the AFC devices. A prestall lift performance degradation for the CRM-HL configuration was resolved with a properly placed nacelle chine. The configuration with nacelle chine was chosen as the representative reference conventional high-lift case for comparison with the CRMSHL- AFC. The AFC-induced lift coefficient increment (DCL) was maintained for the entire lift curve over the CRM-SHL-AFC case with no AFC for almost all flow-control cases examined. The lift curve of the reference CRM-HL have a slightly steeper slope compared to those of the CRM-SHL-AFC configurations. The HELP actuation concept was extremely effective in controlling flow separation in the “linear region” of the curves comparing lift coefficient to mass flow rate. The HELP actuation achieved a targeted DCL of 0.50 using a moderate amount of mass flow and supply air pressure. The CRM-SHL-AFC configuration equipped with HELP actuation was able to match or exceed the lift performance of the reference conventional high-lift configuration (i.e., CRM-HL equipped with a nacelle chine), thus meeting the NASA Advanced Air Transport Technology (AATT) project goal.

Lin, John C.↗
NASA NTRS2019

Surface Flow Visualization of the High-Lift Common Research Model

A 10% scale version of the High-Lift Common Research Model (CRM-HL) was tested in the NASA Langley 14- by 22-Foot Subsonic Tunnel (14x22) in support of the NASA Advanced Air Transport Technology (AATT) Project. The CRM-HL experiment included various configurations such as conventional and simple-hinged flaps, with and without engine nacelle/pylon, with and without nacelle chine, different Active Flow Control (AFC) methods (sweeping jets, alternating pulsed jets, and preconditioned boundary layer blowing), and their various parameters. This particular study is focused on the surface flow visualization of the conventional CRM-HL model at landing configuration. The conventional CRM-HL model with the single-slotted Fowler flap system serves as a baseline for the AFC-enabled simplified high-lift configuration as well as a high-lift technology development platform due to its publicly open geometry. Surface flow visualizations were performed using fluorescent minitufts, which were found to be nonintrusive to the aerodynamic performance. Tuft flow visualizations are supplemented with the relevant pressure and force measurements in order to understand the flow characteristics developed on the conventional CRM- HL model. In addition, three dimensional, unsteady, compressible Computational Fluid Dynamic (CFD) simulations were performed for selective cases. The surface streamlines and transverse velocity fluctuations obtained by the CFD simulations are qualitatively compared to the tuft direction and tuft unsteadiness, respectively. Force measurements of the CRM-HL model show performance degradation at higher angles of attack. Surface flow visualizations revealed the performance loss due to the nacelle/pylon wake that grows with angle of attack and eventually promotes flow separation over the inboard wing. This performance loss was successfully recovered by placing a chine on the engine nacelle.

Koklu, Mehti↗
NASA NTRSDate not supplied

Mitigation of Nacelle/Pylon Wake on the High-Lift Common Research Model Using a Nacelle Chine

A 10% scale, high-lift version of the Common Research Model (CRM-HL) was tested in the NASA Langley Research Center 14-by22-Foot Subsonic Tunnel. The focus of the wind tunnel test campaign was to assess the feasibility of active flow control (AFC) on the simplified CRM-HL configuration. The modular design of the CRM-HL model enabled the testing of the conventional CRM-HL version to establish a benchmark for the AFC research. The wind tunnel model has the capability of being tested with and without the engine nacelle/pylon for comparison. The wind tunnel investigation included the acquisition of force and moment data, steady pressure data, as well as surface flow visualization using minitufts. For some select cases, numerical simulations were performed to aid in understanding the wind tunnel data. Wind tunnel measurements indicated a lift degradation of the conventional CRM-HL at high angles of attack. The surface flow visualization with fluorescent minitufts revealed that the lift degradation is due to flow separation caused by the nacelle/pylon wake on the inboard wing. The wake and the consequent flow separation were successfully mitigated using a nacelle chine installed on the inboard side of the engine nacelle.

Mehti Koklu↗
NASA NTRS2020

FLEET Velocimetry in the Common Research Model’s Wing Wake

Femtosecond laser electronic excitation tagging was used to make velocity measurements in the wake of the wing of the Common Research Model (CRM). Experiments were performed in the NASA Langley Research Center’s National Transonic Facility over a range of tunnel operating conditions. Pressures ranged from 205 to 411 kPa, temperatures from 278 to 323 K, and Mach from 0.1 to 0.9. Velocity was also determined over a range of model angles of attack. Time-averaged velocity results were obtained in both air and nitrogen, while single-shot velocity was obtained under certain tunnel operating conditions. Spatially-resolved, two dimensional, single component velocity measurements were achieved using a newly-developed laser scanning technique, which proved sufficiently sensitive to measure an approximately 5% velocity deficit in the wing wake region of the CRM.

Daniel T Reese↗
NASA NTRSDate not supplied

Requirements and Challenges for CFD Validation within the High-Lift Common Research Model Ecosystem

The High-Lift Common Research Model (CRM-HL) ecosystem is envisioned to become an industry standard set of test cases for high-lift aerodynamics prediction, with data generated providing a strong foundation for CFD validation. Since its original development, preliminary wind tunnel tests have been conducted to further understand and configure the geometry, and several more are in the planning phases. It is anticipated that the data generated in these tests will be used extensively by the CFD community for research, development, and validation of new techniques that yield more accurate results. To derive the maximum benefit from planned wind tunnel testing, data acquisition will be focused in several key areas to address specific shortcomings in CFD predictive capabilities. Significant challenges currently exist in areas including, but not limited to, characterizing high-lift flow phenomena, quantifying effects due to configuration changes, understanding wind tunnel and model installation effects, and establishing data uncertainty. This paper will discuss the current state-of-the-art in high-lift CFD prediction, key limitations of current CFD methods and tools, establishing a validation dialog between test and CFD practitioners, and the flow phenomena of highest interest, in an effort to begin to address these challenges. To this end, it is expected that the data generated from CRM-HL tests will form a strong foundation for future predictive capability.

Adam M Clark↗
NASA NTRS2021

Assessment and Improvement of RANS-based Transition Models based on Experimental Data of the Common Research Model with Natural Laminar Flow

Transition models based on auxiliary transport equations augmenting the Reynolds-averaged Navier-Stokes (RANS) framework often rely upon the correlations that were derived from a limited number of low-speed experiments and do not account for all of the transition mechanisms and/or their variation with the significant flow parameters. Available data from a recent experiment in the National Transonic Facility at the NASA Langley Research Center are used to assess the current transition modeling capability in NASA's OVERFLOW 2.2o code for a swept wing configuration at transonic cruise conditions. Specifically, the OVERFLOW solutions are used together with detailed stability analysis of the boundary layer flow over the new Common Research Model with Natural Laminar Flow (CRM-NLF) to evaluate the accuracy and the robustness of the transport-equation-based transition models, with the goal of proposing improvements that would help to strengthen the physical basis of these models for the important class of flows involving the combined effects of crossflow and flow compressibility. Results highlight the significant underprediction of the laminar flow extent within the inboard region of the wing, wherein the onset of transition may be attributed to a gradual amplification of Tollmien-Schlichting instabilities.

Boundary layer transition↗
NASA NTRSDate not supplied

Summary of the NASA Semi-Span High-Lift Common Research Model Wind Tunnel Test at the QinetiQ 5-Metre Low-Speed Facility

A summary and selected results from experimental testing of the NASA 10% scale semi-span High-Lift Common Research Model (CRM-HL) at the QinetiQ 5m (5mWT) pressurized low-speed wind tunnel are presented. There were many objectives of this test, the primary being to define a set of reference configurations for dissemination and use within the CRM-HL ecosystem, one in the landing configuration and one in the takeoff configuration. A database of force, moment, pressure and surface flow visualization data was collected to support several objectives: aerodynamic sensitivity to high-lift device positioning, Reynolds number effects on configuration selection, isolation of the effects of various components of the reference configuration e.g. landing gear, nacelle, horizontal tail, etc., and limited repeatability data for uncertainty quantification assessment. Some results were compared to limited data collected at the NASA Langley Research Center 14x22 wind tunnel to assess half-model effects and facility differences. Half-model effects were further studied with use of floor blowing to change boundary layer profile and assess effects on model aerodynamics. Flow visualization data were gathered with fluorescent mini-tufts and UV oil. Finally, test time was spend working on the development of new Particle Image Velocimetry (PIV) and Model Deformation Measurement (MDM) capabilities at the 5mWT facility.

Ashley Evans↗
NASA NTRSDate not supplied

Design Exploration of a Slotted-Wing Common Research Model

A knowledge-based aerodynamic design method, Constrained Direct Iterative Surface Cur-vature (CDISC), has been leveraged for the computational design exploration of a Common Research Model with Reduced-Sweep and Slotted Wings (CRMRS-SW). Cruise-slotted-wing airfoils include a slot near the trailing edge of a main airfoil component to introduce stream air to the low-momentum, upper-surface boundary layer on a flap airfoil component with the goal of allowing for a more aft loading, relative to supercritical airfoils, without shock-induced separation. Ultimately, the cruise slotted wing is a passive technology that allows for an in-crease in the drag divergence Mach number and/or an increase in aerodynamic efficiency at agiven cruise condition. These aerodynamic benefits may be realized at the vehicle level through a trade space that includes the following design options: increasing cruise Mach number, in-creasing wing thickness, decreasing wing sweep, increasing lift coefficient and/or decreasing drag coefficient. The present study aimed to evaluate the slotted-wing concept’s potential as adrag-saving technology in application to a single-aisle transonic transport aircraft at a given cruise condition. The CDISC design method was used to develop a better understanding of the slotted-wing design variables that have a significant impact on the variability in aircraft drag and leverage this newly-developed knowledge to quantify the aerodynamic performance benefits enabled by the cruise slotted wing.

Brett R. Hiller↗
NASA NTRSDate not supplied

Towards a Common Basis of Comparison Across a Broad Trade Space of Mars Architecture Options

Humanity’s fascination with Mars predates the advent of space access, but the coming-of-age of rocket propulsion in the mid-20th century provided the technological foundation for considering a human visit to the red planet. Werner von Braun’s “The Mars Project,” published in 1953, is acknowledged as the first integrated Mars mission architecture plan [1]; since then, the reformulation and refinement of Mars architectures and system concepts has been an ongoing activity, as continued study and planning for human Mars missions is necessary in order to incorporate evolving mission objectives, technology advancements, and the increasing body of knowledge regarding human factors and the various environments of space. Historical Mars architecture studies represent an enormous body of work, but apart from a couple of high-level reviews [2], tapping into the findings and philosophies of these varied works entails a tedious and time-consuming individual effort. The unfortunate result of the widely scattered corpus of Mars architectures is that knowledge and understanding acquired in previous studies is not consistently and effectively brought to bear in the studies of today. The primary vehicle for bringing forward past learning is human recall, which both is imperfect and experiences significant attrition. An effort is underway in the Advanced Concepts Office (ACO) at NASA’s Marshall Space Flight Center to recapture and re-baseline previous architecture studies in order to establish a broad basis of comparison for future Mars architecture studies. Recapturing involves gathering and organizing data and documentation from previous efforts; re-baselining entails developing models capable of reproducing the original results, and then utilizing these models to implement a common set of ground rules and assumptions across the resulting trade space of Mars architecture options. This paper will present the methodology ACO is employing in performing this architecture meta-study, including a discussion on the challenges involved in re-baselining without losing the intent behind previous concepts. As part of this discussion some initial results will be presented, along with a list of studies targeted for inclusion. It is expected that the completed basis of comparison results will be presented as a follow-on paper in the following year.

Stephen James Edwards↗
NASA NTRSDate not supplied

Common Scientific and Technological Interests Between Astrobiology and Space Biology

The disciplines of astrobiology (AB) and space biology (SB) clearly have common interests, however they have not been pursued jointly. SB and AB are inextricably linked, both intellectually and technologically. They can now be effectively linked operationally. Cross-cutting joint collaborations will enhance innovation and increase cost effectiveness. Session topics include joint science questions, technologies, instrumentation, and missions. Examples include life detection, overlapping planetary protection concerns, biofilms, radiation, hyper- and hypogravity, applications of artificial intelligence and machine learning, interoperable databases, facilities (i.e., spacecraft, lunar surface efforts, simulation chambers, analog sites, etc.), training opportunities, and other topics relevant to AB and SB joint ventures. We welcome contributions on this very broad topical area to facilitate cross-fertilization of these disciplines that are of great importance to NASA.

astrobiology↗
NASA NTRSDate not supplied

Surface-Normal Active Flow Control for Lift Enhancement and Separation Mitigation for High-Lift Common Research Model

This study explores the feasibility of using small surface-normal jets near the flap trailing edge as active aerodynamic load control on the high-lift Common Research Model wing/-body configuration. Chimera Grid Tools are utilized to generate structured curvilinear overset grids, and the Reynolds-averaged Navier-Stokes solver OVERFLOW is employed to solve for the flow-field around the geometry. The so-called microjet is initially employed across both the inboard and the outboard flaps on the pressure-side near the trailing edge. It is shown that implementing the microjet on the inboard flap is more effective compared to implementing it on the outboard flap. This is because, prior to microjet implementation, the flow on the outboard flap exhibits extensive separation, while the flow on the inboard flap exhibits moderate separation. For microjet implementation across the inboard flap only, the relationship between momentum coefficient of the microjet and lift-enhancement is found to be∆CL'1.66√Cμfor the rangeCμ= 0.00−0.012. We show that implementing a microjet with a jet velocity ratio of one, which corresponds toCμ= 0.003, can shift the linear region of the lift curve by ∆CL= 0.08. The linear shift in the lift curve is significant for enhancing airplane performance such as increasing its payload. Microjet implementation effects on the drag coefficient are also investigated through a drag decomposition analysis. Further, we employ an induced drag analysis based on the spanwise load distribution and show that the microjet-related increase in pressure drag coefficient is dominated by the increase in the induced drag while microjet implementation reduces the form drag. These preliminary results show that favorable changes in aerodynamic performance can be achieved by using the surface-normal jets presented in this study.

ARMD↗
NASA NTRS2021

Assessment of RANS-based Transition Models based on Experimental Data of the Common Research Model with Natural Laminar Flow

Transition models based on auxiliary transport equations augmenting the Reynolds-averaged Navier-Stokes (RANS) framework often rely upon transition correlations that were derived from a limited number of low-speed experiments and these models often fail to account for all of the relevant transition mechanisms and/or the variation in those mechanisms with respect to changes in the significant flow parameters. Available data from a recent experiment on the Common Research Model with Natural Laminar Flow (CRM-NLF) in the National Transonic Facility at the NASA Langley Research Center are used to assess the current transition modeling capability in NASA's OVERFLOW 2.3b solver for a swept wing configuration with nonzero taper and transonic cruise conditions. Specifically, the OVERFLOW solutions are used to evaluate the accuracy and robustness of the transport-equation-based transition models. Results highlight that the Spalart-Allmaras-based amplification factor transport (AFT-2017b) equation model and Menter’s shear-stress transport equation (SST2003)-based Langtry-Menter transition models (either with or without the modeling of crossflow transition) significantly underpredict the reported extent of laminar flow region over the entire span of the wing, irrespective of which instability mechanism(s) is expected to dominate the onset of the transition process. We show that the transition correlations underlying these models fail to account for the stabilizing effect of compressibility on the Tollmien-Schlichting transition, which is likely to be a major contributor to the underprediction of the laminar flow region on the CRM-NLF. The SST-2003-based Langtry-Menter model also appears to inaccurately predict the chordwise pressure variation along the majority of the wing span at all the flow conditions studied herein, due to how the turbulence intensity levels were enforced in the computations and how that was interfering with the functioning of the underlying turbulence model within the boundary layer. The AFT and Langtry-Menter models appear to be sensitive to the level of the freestream turbulence intensity, but the degree of sensitivity varies across the models.

CFD modeling↗
NASA NTRSDate not supplied

Development of the 10% NASA CRM High-Lift Common Research Model (CRM-HL)

A 10%-scale Common Research Model-high lift version (CRM-HL) was developed to support extensive experimental investigations in the areas of active flow control, control surface optimization for landing and take-off, acoustic technology development, and computational fluid dynamics code validation to name a few. The CRM-HL was designed to have modular components that will enable the model to be tested in the following three forms: (1) conventional high-lift (CHL) configuration, (2) Active Flow Control (AFC) enabled simple hinged flap high-lift (SHL) configuration, and (3) CHL configuration with noise reduction treatments for the slats and/or the flaps. This paper describes the design, analysis, and fabrication of the CRM-HL for testing in the NASA Langley Research Center (LaRC) 14 by 22-Foot Subsonic Tunnel (14x22) and other wind tunnels as deemed appropriate by the research community such as the Qinetiq 5 Meter tunnel.

Jared S. Fell↗
NASA NTRSDate not supplied

Real-Time Drag Optimization of Aspect Ratio 13.5 Common Research Model with Distributed Flap System

This paper presents a real-time drag optimization study of the aspect ratio 13.5 Common Research Model (CRM) with a distributed mini-plain flap system. A surrogate aerodynamic model of the aspect ratio 13.5 CRM is developed based on an aerodynamic database computed by a transonic panel method to capture the aerodynamic coefficients as functions of the angle of attack, flap deflections, and Mach number. A recursive least-squares parameter estimation algorithm is designed to estimate the aerodynamic parameters of the surrogate model. The estimated surrogate model is then used in an on-line drag optimization strategy based on an adjoint method. The results of the real-time drag optimization indicate a drag reduction of 2.46% for Mach 0.80, 3.37% for Mach 0.85, and 1.95% for Mach 0.88. The results show the convergence of all parameter estimates.

Drag Optimization↗
NASA NTRS2022

Charging Experiments and Filtration Testing on Facemask Materials: Towards Goals of Full Performance Restoration of Used N95 Masks and Enhancement of Common-Fabric Facemasks

Different techniques have been developed for sanitizing N95 masks while retaining whatever charge remains on them. However, these sanitizing methods do not address the fact that the electrical charge, filtration efficacy, and breathability of such masks may be expected to degrade during long-term use based on mechanisms known in the literature. In this study, approaches to electrically (re)charging facemask filter materials were explored in response to the COVID-19 induced shortage of N95 masks. The effort consisted of charging experiments followed by filtration testing conducted at the coupon level during a month-long period (May 2020). The main focus of the work was to develop a recharging technique which could eventually be adapted and used as part of a broader full-performance restoration process for used N95 masks, e.g., which might employ simple washing by alcohol or soapy water as a preceding step for sanitization and declogging. Most tested coupons were therefore nonwoven meltblown fibrous polypropylene (PP) filter media extracted from decades old N95 masks. Keeping in mind commonly used cloth facemasks, limited trials were also performed with some commercially available fabrics. Charging was done at elevated temperature and was followed by cooling to freeze in the applied charges produced from corona discharges using different electrode configurations and parameter combinations, or from triboelectric rubbing. Charging was also focused on using potentially scalable equipment, e.g., Van de Graaff generators or consumer ionic hair products. Some degree of success was achieved with one of the fabrics and the PP filter media which was first purposefully discharged to have typical filtration efficiency (FE) of ~35%. Numerous attempts at corona charging discharged media resulted in filtration efficiency (FE) ≥ 80 – 85%. Some measure of charge robustness was also established via stable performance during loading testing. However, results where FE ≥ 90% were not reliably repeatable and no results met the FE ≥ 95% goal due to shortcomings of the charging process. The best three trials for PP media statistically met the FE ≥ 90% criteria, amounted to a small percentage of the trials relying on an ionic hair dryer, and are attributed to good embedding of charges via aerodynamic force. Triboelectric charging significantly enhanced the viability of one of the polyester fabrics –measured FE increased from 19% up to 46% while maintaining a reasonably low pressure drop.

N95↗