Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation densities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Structural representation of additively manufactured 316L austenitic stainless steel

Three 316L stainless steel materials are studied and reported upon; wrought, as-built additively manufactured (AM), and heat-treated AM material. The AM material was produced from the laser engineered net shaping (LENS) process. Macroscopic uniaxial compression stress-strain curves were obtained for all three materials. The curves were similar for the wrought and heat-treated AM materials but the as-built AM material demonstrated approximately 1.7 times greater flow stress at any given level of strain than the other two materials. Electron-backscatter diffraction analysis of the materials also showed that the microstructures of the three materials differed; with complex grain morphology for the as-built AM material. The mean grain size of each of the three materials also differed. Furthermore, the initial dislocation density was also measured with neutron diffraction and line-profile analysis for both wrought and as-built AM materials with the density in the AM material approximately 2.5 times greater.

36 MATERIALS SCIENCE↗

High mobility AlGaN/GaN heterostructures grown on Si substrates using a large lattice-mismatch induced stress control technology

A large lattice-mismatch induced stress control technology with a low Al content AlGaN layer has been used to grow high quality GaN layers on 4-in. Si substrates. The use of this technology allows for high mobility AlGaN/GaN heterostructures with electron mobility of 2040 cm{sup 2}/(V·s) at sheet charge density of 8.4 × 10{sup 12 }cm{sup −2}. Strain relaxation and dislocation evolution mechanisms have been investigated. It is demonstrated that the large lattice mismatch between the low Al content AlGaN layer and AlN buffer layer could effectively promote the edge dislocation inclination with relatively large bend angles and therefore significantly reduce the dislocation density in the GaN epilayer. Our results show a great potential for fabrication of low-cost and high performance GaN-on-Si power devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Stochastic dislocation kinetics and fractal structures in deforming metals probed by acoustic emission and surface topography measurements

We demonstrate that the fractal dimension (FD) of the dislocation population in a deforming material is an important quantitative characteristic of the evolution of the dislocation structure. Thus, we show that peaking of FD signifies a nearing loss of uniformity of plastic flow and the onset of strain localization. Two techniques were employed to determine FD: (i) inspection of surface morphology of the deforming crystal by white light interferometry and (ii) monitoring of acoustic emission (AE) during uniaxial tensile deformation. A connection between the AE characteristics and the fractal dimension determined from surface topography measurements was established. As a common platform for the two methods, the dislocation density evolution in the bulk was used. The relations found made it possible to identify the occurrence of a peak in the median frequency of AE as a harbinger of plastic instability leading to necking. It is suggested that access to the fractal dimension provided by AE measurements and by surface topography analysis makes these techniques important tools for monitoring the evolution of the dislocation structure during plastic deformation—both as stand-alone methods and especially when used in tandem.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The source of the threading dislocation in GaSb/GaAs hetero-structures and their propagation mechanism

The misfit and threading dislocations during GaSb epitaxy on GaAs substrate were investigated by weak beam dark field and high angle dark field scanning transmission electron microscopy. The geometric phase analysis and dislocation density tensor analysis were next used to analyze the strain around the threading dislocations and quantify the corresponding Burgers vectors. It is shown that there are three types of threading dislocations (mixed, edge, and pair of mixed types) close to the interface, which originate from the 60 Degree-Sign , Lomer, and 60 Degree-Sign pair misfit dislocations, respectively. During the growth of the epitaxial layer, the edge type as well as the pair of mixed threading dislocations split into two mixed type dislocations for the glide in {l_brace}111{r_brace} planes. Eventually, only mixed type dislocations have been observed at the surface of thick GaSb layers.

36 MATERIALS SCIENCE↗

Investigation of the role of deposition rate on optical, microstructure and ethanol sensing characteristics of nanostructured Sn doped In2O3 films

Highlights: • Deposition rate can play an important role in gas sensing of In{sub 2}O{sub 3}:Sn films. • The crystallite size and linear defects of the films is estimated by eCMWP method. • The correlation between the optical, microstructure and gas sensing properties is studied. • The size distribution behavior of samples is in agreement with the results of porosity. • Optimum deposition rate for In{sub 2}O{sub 3}:Sn films is 0.2 nm/s. - Abstract: In this paper, Sn doped In{sub 2}O{sub 3} (In{sub 2}O{sub 3}:Sn) nanostructured films as metal oxide semiconductor material which is very important in optoelectronics and gas sensing industries, were prepared by thermal evaporation technique. It is discussed how different deposition rate (0.1, 0.2, 0.3 and 0.4 nm/s) affects the optical, electrical, microstructural and ethanol gas sensing characteristics of In{sub 2}O{sub 3}:Sn films and must be precisely monitored. The gas sensing performance of the films was evaluated in terms of gas concentration and operating temperature. A correlation between the crystallite size, porosity, dislocation density, outer cut-off radius of dislocation, optical band gap, activation energy and sensitivity of the films was established. The results demonstrate that the maximum sensitivity to ethanol vapors can be obtained for the sample grown at deposition rate of 0.2 nm/s. The response and recovery times of this sensor exposed to 100 ppm of ethanol vapors were determined and found to be 9.0 s and 3.9 s, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Crystal plasticity modeling of irradiation growth in Zircaloy-2

A reaction-diffusion based mean field rate theory model is implemented in the viscoplastic self-consistent (VPSC) crystal plasticity framework to simulate irradiation growth in hcp Zr and its alloys. A novel scheme is proposed to model the evolution (both number density and radius) of irradiation-induced dislocation loops that can be informed directly from experimental data of dislocation density evolution during irradiation. This framework is used to predict the irradiation growth behavior of cold-worked Zircaloy-2 and trends compared to available experimental data. The role of internal stresses in inducing irradiation creep is discussed. Effects of grain size, texture, and external stress on the coupled irradiation growth and creep behavior are also studied.

36 MATERIALS SCIENCE↗

A method to predict fatigue crack initiation in metals using dislocation dynamics

Abstract A theory is proposed to predict the initiation of fatigue cracks using cyclic dislocation dynamics (DD) simulations. The evolution of dislocation networks in a grain is simulated over several cycles. It is shown that the dislocation density and the energy stored in the dislocation networks increase with the number of cycles. The results of the DD simulations are used to construct an energy balance expression for crack initiation. A hypothetical crack is inserted into the grain, and the Gibbs energy consisting of the energy of the dislocation structure, the surface energy of the hypothetical crack, and the reduction in continuum energy is evaluated. Once the Gibbs energy attains a maximum, the dislocation structure becomes unstable, and it becomes energetically more favorable to form a real crack. The proposed method is applied to oxygen-free high conductivity copper, and the results are compared against experiments. Finally, it is shown how the method can be amended to account for environmental effects.

Electrochemistry↗

Effect of temperature on the nano/microstructure and mechanical behavior of nanotwinned Ag films

In situ and ex situ annealed nanotwinned (NT) Ag thin films have been investigated by TEM and tensile testing to reveal the thermal stability of the twin boundaries, grain boundaries, dislocation densities, and their respective influence of the macroscopic yield stress. The NT Ag films synthesized by magnetron sputtering form both coherent (CTB, Σ3{111}) and incoherent (ITB, Σ3{112}) twin boundaries that are thermally stable up to 473 K (200 Celsius), i.e., no obvious changes in grain size, twin spacing, and yield stress. In situ TEM observations show the dislocations become mobile at 453 K (180 Celsius) resulting in dislocation annihilation primarily at twin and grain boundaries. Rotation of grains with low-angle grain boundaries was observed during in situ heating, resulting in the growth of columnar grains above 453 K (180 Celsius). However, no noticeable changes in the spacings of CTBs were observed during the entire in situ and ex situ annealing [up to 873 K (600 Celsius)]. The increase in grain size and concomitant decrease in yield stress following annealing at various temperatures can be described by the Hall-Petch relationship, demonstrating that grain size rather than twin spacing is most sensitive to thermal annealing and plays a dominant role in the deformation of NT Ag films.

36 MATERIALS SCIENCE↗

Laser shocking of materials: Toward the national ignition facility

In recent years a powerful experimental tool has been added to the arsenal at the disposal of the materials scientist investigating materials response at extreme regimes of strain rates, temperatures, and pressures: laser compression. In this paper, this technique has been applied successfully to mono-, poly-, and nanocrystalline metals and the results have been compared with predictions from analytical models and molecular dynamics simulations. Special flash x-ray radiography and flash x-ray diffraction, combined with laser shock propagation, are yielding the strength of metals at strain rates on the order of 10 7 –10 8 s -1 and resolving details of the kinetics of phase transitions. A puzzling result is that experiments, analysis, and simulations predict dislocation densities that are off by orders of magnitude. Finally, other surprises undoubtedly await us as we explore even higher pressure/strain rate/temperature regimes enabled by the National Ignition Facility.

36 MATERIALS SCIENCE↗

Compositionally graded Ga 1-x In x P buffers grown by static and dynamic hydride vapor phase epitaxy at rates up to 1 μm/min

Here, we demonstrate Ga 1-x In x P compositionally graded buffers (CGBs) grown on GaAs with lattice constants between GaAs and InP by hydride vapor phase epitaxy (HVPE). Growth rates were up to ~1 μm/min and threading dislocation density (TDD) was as low as 1.0 x 10 6 cm -2 . We studied the effect of substrate offcut direction, growth rate, and strain grading rate on CGB defect structure. We compared the effect of a “dynamic grading” style, which creates compositional interfaces via mechanical transfer of a substrate between two growth chambers, vs. “static grading” where the CGB grows in a single chamber. Dynamic grading yielded smoother grades with higher relaxation, but TDD was not significantly different between the two styles. Substrate offcut direction was the most important factor for obtaining CGBs with low defect density. (001) substrates offcut towards (111)B yielded smoother CGBs with lower TDD compared to CGBs grown on substrates offcut towards (111)A. Transmission electron microscopy of static and dynamic CGBs grown on A and B-offcuts only found evidence of phase separation in a static A-offcut CGB, indicating that the B offcut limits phase separation, which in turn keeps TDD low. Reduced growth rate led to the appearance CuPt-type atomic ordering, which affected the distribution of dislocations on the active glide planes but did not alter TDD. Higher growth rates led to smoother CGBs and did not appreciably increase TDD as otherwise predicted by steady-state models of plastic relaxation. These results show HVPE’s promise for lattice-mismatched applications and low-c ost InP virtual substrates on GaAs

36 MATERIALS SCIENCE↗

Strength-ductility synergy through microstructural and compositional heterogeneity in directed energy deposition additive manufacturing of face-centered cubic materials

Directed energy deposition (DED) is an additive manufacturing (AM) process based on welding technology and offers the advantages of large build volume, high deposition rate, and ability to fabricate multi-material parts. Epitaxial continuous columnar grain growth is a characteristic microstructural feature of DED processed alloys. In this study, a bamboo-like microstructure (periodic alternation of equiaxed and columnar structure) was produced by adopting an intermittent deposition strategy in 316L stainless steel and Inconel 625. The formation of a bamboo-like alternating microstructure was confirmed through electron backscattered diffraction (EBSD) analysis. Hardness mapping showed that the columnar to equiaxed transition (CET) occurred at the region right below the fusion line. A finite element (FE) model was used to investigate the relationship between the temperature gradient (G) and the solidification rate (R). The FE model showed a low G/R ratio at the region right below the interface promoting the CET. The grain size and material-dependent deformation behaviors are analyzed using digital image correlation (DIC). The lower deformation on the fine-grain regions observed in DIC analysis is attributed to a higher strain hardening rate, which is confirmed through dislocation density analysis on a tensile-interrupted specimen. The periodically alternating grain size coupled with the microstructural changes caused by intermittent deposition strategy result in a better strength-ductility synergy in both single-material and bimetallic specimens.

36 MATERIALS SCIENCE↗

Laser Powder Directed Energy Deposition of Steels for Nuclear Applications

This comprehensive investigation examines the structure–property relationships in two nuclear alloy systems—Alloy 709 (A709) austenitic stainless steel and Grade 92 (G-92) ferritic/martensitic (F/M) steel—manufactured via directed energy deposition (DED) for sodium-cooled fast reactor applications. This study establishes the fundamental mechanisms for controlling microstructures for optimizing the mechanical performance of additively manufactured nuclear materials through systematic heat treatment optimization and multiscale characterization. As-deposited A709 steel develops a complex multiscale strengthening architecture consisting of a fine cellular solidification structure with diameter of 2-3 µm within10–50 µm grains, elevated dislocation densities from rapid thermal cycling, and grain boundary precipitates that activate concurrent Hall–Petch, dislocation, and precipitation hardening mechanisms to achieve exceptional properties [yield strength (YS): 603 MPa, ultimate tensile strength (UTS): 844 MPa, Vickers hardness: 220 HV] that achieve a 44% superior strength compared to that of the wrought material. Heat treatments produce different results. Solution annealing (SA) dissolves the cellular structure and reduces the hardness to 190 HV. Precipitation treatment (PT) keeps the cellular structure but adds carbides, allowing the hardness to reach 205 HV. The best approach combines both treatments (SA+PT) and creates uniform precipitate distributions with M 23 C 6 carbides at the grain boundaries and MX carbonitrides in the matrix, achieving a hardness of 195 HV. However, directional differences persist, with a 12%–15% strength variation between orientations due to the inherited layered microstructural architecture that survives aggressive heat treatment. While tensile testing at 550°C demonstrates 40%–50% thermal softening with dynamic strain aging, DED A709 steel still maintains a 71% higher YS than that of the wrought material. Ion irradiation studies (100–400 dpa) of DED A709 steel reveal progressive radiation damage with increasing void density and radiation-induced segregation causing nickel enrichment and chromium depletion, which will ultimately compromise mechanical properties. As-deposited G-92 exhibits exceptional strength (UTS: 1650–1700 MPa, 430 HV) through a complex microstructure containing both ferrite and martensite phases, a high geometrically necessary dislocation (GND) density (17.04×10 14 /m 2 ), and fine carbides. Heat treatments create distinct changes. Normalizing produces fresh martensite with the highest hardness (460 HV) and an increased GND density (20.23×10 14 /m 2 ). Tempering develops dual precipitation systems and reduces the hardness to 290 HV. The optimal approach uses sequential normalizing plus tempering, achieving balanced properties with the lowest hardness (250 HV) and a reduced GND density (11.01×10 14 /m 2 ). A processing-dependent anisotropy is observed: horizontal specimens achieve superior ductile behavior, while vertical specimens exhibit brittle failure. A tempering heat treatment successfully mitigates this anisotropic behavior by transforming the hard martensitic as-deposited structure into tempered martensite enabling both horizontal and vertical specimens to exhibit similar stress–strain characteristics with visible necking behavior. Remarkably, testing at 550°C reveals a reversal in the anisotropy, where as-deposited specimens achieve near isotropy with superior thermal stability (a 15%–20% strength reduction), while tempered specimens develop an orientation dependence with a 25%–30% strength reduction. Both alloy systems demonstrate that DED processing creates specimens with a superior strength through refined microstructural features, though with distinct strengthening mechanisms—austenitic through cellular structures and precipitates versus F/M through phase transformations and precipitates. Heat treatment optimization requires alloy-specific approaches, with A709 benefiting from controlled precipitation while G-92 requires careful phase transformation control. The results show that DED manufacturing can produce nuclear materials with exceptional performance, but directional effects and temperature-dependent behavior must be carefully considered for reactor component design and qualification.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

The Convolutional Multiple Whole Profile (CMWP) Fitting Method, a Global Optimization Procedure for Microstructure Determination

The analysis of line broadening in X-ray and neutron diffraction patterns using profile functions constructed on the basis of well-established physical principles and TEM observations of lattice defects has proven to be a powerful tool for characterizing microstructures in crystalline materials. These principles are applied in the convolutional multiple-whole-profile (CMWP) procedure to determine dislocation densities, crystallite size, stacking fault and twin boundary densities, and intergranular strains. The different lattice defect contributions to line broadening are separated by considering the hkl dependence of strain anisotropy, planar defect broadening and peak shifts, and the defect dependent profile shapes. The Levenberg–Marquardt (LM) peak fitting procedure can be used successfully to determine crystal defect types and densities as long as the diffraction patterns are relatively simple. However, in more complicated cases like hexagonal materials or multiple-phase patterns, using the LM procedure alone may cause uncertainties. Here, we extended the CMWP procedure by including a Monte Carlo statistical method where the LM and a Monte Carlo algorithm were combined in an alternating manner. The updated CMWP procedure eliminated uncertainties and provided global optimized parameters of the microstructure in good correlation with electron microscopy methods.

36 MATERIALS SCIENCE↗

Deformation, dislocation evolution and the non-Schmid effect in body-centered-cubic single- and polycrystal tantalum

A physically-informed continuum crystal plasticity model is presented to elucidate deformation mechanisms, dislocation evolution and the non-Schmid effect in body-centered-cubic (bcc) tantalum widely used as a key structural material for mechanical and thermal extremes. We show the unified structural modeling framework informed by mesoscopic dislocation dynamics simulations is capable of capturing salient features of the large inelastic behavior of tantalum at quasi-static (10 -3 s -1 ) to extreme strain rates (5000 s -1 ) and at low (77 K) to high temperatures (873 K) at both single- and polycrystal levels. Here we also present predictive capabilities of the model for microstructural evolution in the material. To this end, we investigate the effects of dislocation interactions on slip activities, instability and the non-Schmid behavior at the single crystal level. Furthermore, ex situ measurements on crystallographic texture evolution and dislocation density growth are carried out for polycrystal tantalum specimens at increasing strains. Numerical simulation results also support that the modeling framework is capable of capturing the main features of the polycrystal behavior over a wide range of strains, strain rates and temperatures. The theoretical, experimental and numerical results at both single- and polycrystal levels provide critical insight into the underlying physical pictures for micro- and macroscopic responses and their relations in this important class of refractory bcc materials undergoing large inelastic deformations.

36 MATERIALS SCIENCE↗

Deformation behavior of CP-titanium under strain path changes: Experiment and crystal plasticity modeling

The deformation behavior of commercially pure rolled titanium subjected to strain path changes is studied using experiments and a crystal plasticity model. Four different loading combinations are performed at room temperature to study the activation of slip, twinning, de-twinning and double-twinning in hexagonal closed packed titanium. The strain paths considered are: rolling direction compression (RDC) followed by normal direction compression (NDC), RDC followed by transverse direction compression (TDC), NDC followed by RDC, and NDC followed by TDC. An EBSD-based analysis of the distribution of boundary misorientation angles before and after reload was developed to analyze the evolution of {$10\bar{1}2$} tensile and {$11\bar{2}2$} compression twins. This analysis supports the model results concerning the treatment of twin reorientation. A de-twinning and double-twinning model accounting for back stress effects, an important feature of strain path changes, is implemented within the framework of the visco-plastic self-consistent (VPSC) model along with a dislocation density (DD) based hardening scheme. In the model, plasticity is accommodated by prismatic $\langle$a$\rangle$, basal $\langle$a$\rangle$ and pyramidal $\langle$c+a$\rangle$ slip modes, and {$10\bar{1}2$} tensile and {$11\bar{2}2$} compression twinning modes. The VPSC model predicts the evolution of twinning, de-twinning and double-twinning processes for both tensile and compression twinning modes under strain path change. The model predicts macroscopic stress-strain response, texture evolution, and twin volume fraction that are in agreement with experimental observations. The evolution of texture is investigated in detail by separately analyzing the twinned domains, rather than the evolution of the global texture.

36 MATERIALS SCIENCE↗

Microstructure and residual elastic strain at graphite nodules in ductile cast iron analyzed by synchrotron X-ray microdiffraction

The microstructure and residual elastic strain at graphite nodules (GNs) in ductile cast iron produced using either a fast or slow cooling rate have been characterized using synchrotron 3D X-ray Laue microdiffraction. The results demonstrate that thermal stress is introduced during cooling and that part of this stress is relaxed by plastic deformation of the polycrystalline ferrite matrix. It is observed that the plastic deformation is accommodated by the formation of dislocations and dislocation boundaries, which are organized in a cell structure. The dislocation density quantified based on the microstructure is most pronounced at the GN/matrix interface around small GNs in the fast cooled sample. Residual elastic strain is also present, which is mainly compressive with a maximum of 6.0–9.9 × 10 -4 near the GNs. Gradients of plastic deformation and elastic strain field around the GNs are observed. The results document for the first time that both the elastic strain field and the plastic strain field averaged over the grains around the GNs is approximately scaling with GN size and not affected by the cooling rate. The experimental data are compared with simulations by a finite element method, and agreement and disagreement are considered in detail.

36 MATERIALS SCIENCE↗

Suppression of phase separation in AlGaInAs compositionally graded buffers for 1550 nm photovoltaic converters on GaAs

We investigate strategies to suppress phase separation and reduce threading dislocation density (TDD) in AlGaInAs compositionally graded buffers (CGBs) that span the lattice constant range from GaAs to InP. Combining the results from high resolution x-ray diffraction, cathodoluminescence, transmission electron microscopy, and photovoltaic device measurements, we correlate the choices of epitaxial growth conditions with the defect structure of the CGBs and subsequent device performance. Both the use of substrates with high misorientation off (100) toward the (111)A plane and Zn doping instead of Si doping are shown to suppress phase separation and reduce TDD. We demonstrate a 0.74 eV GaInAs device grown on a GaAs substrate offcut 19.5° toward (111)A using a Zn-doped AlGaInAs CGB with TDD = 3.5 ± 0.2 × 10 6 cm -2 that has a bandgap-open circuit voltage offset of only 0.434 V measured under the AM1.5G solar spectrum. We characterized this device under high-intensity irradiance from a 1570 nm laser and measured a 31.9% peak laser power conversion efficiency at 3.6 W/cm 2 irradiance. These results provide a roadmap to the manufacture of laser- and thermal-power conversion devices with the performance and cost-effectiveness needed to drive adoption of these technologies at scale.

14 SOLAR ENERGY↗

Application of X-ray Technique to Study the Structure of Ultrafine-Grained Ferritic/Martensitic Steel

In this work, x-ray diffraction and transmission electron microscopy (TEM) analyses have been applied to study the structure of ultrafine-grained (UFG) ferritic/martensitic steel as compared to coarse-grained samples subjected to standard treatment. The x-ray phase analysis of diffraction patterns taken in the “transmission” mode allowed determining the volume fraction and phase composition of particles in the UFG samples. The lattice parameter, the size of coherent scattering domains, the averaged dislocation density, and the fraction of edge and screw dislocations of the ferritic phase in steel were determined according to the diffraction patterns taken in the “reflection” mode. The small-angle x-ray scattering (SAXS) technique was used to study the quantitative characteristics of the size, shape, and distribution of precipitates in the UFG samples. The TEM investigations were performed on the same foils to confirm the results of SAXS. The quantitative evaluations of dispersion and dislocation hardenings in ferritic/martensitic steel were conducted on the basis of the results obtained.

36 MATERIALS SCIENCE↗