Results for “edge instability” — Page 24

NASA NTRS1994

Using FU Orionis outbursts to constrain self-regulated protostellar disk models

One-dimensional, convective, vertical structure models and one dimensional time-dependent, radial diffusion models are combined to create a self-consistent picture in which FU Orionis outbursts occur in young stellar objects (YSOs) as the result of a large-scale, self-regulated, thermal ionization instability in the surrounding protostellar accretion disk. Although active accretion disks have long been postulated to be ubiqitous among low-mass YSOs, few constraints have until now been imposed on physical conditions in these disks. By fitting the results of time-dependent disk models to observed timescales of FU Orionis events, we estimate the magnitude of the effective viscous stress in the inner disk (r approximately less than 1 AU) to be, in accordance with an ad hoc 'alpha' prescription, the product of the local sound speed, pressure scale height, and an efficiency factor alpha of 10(exp -4) where hydrogen is neutral and 10(exp 3) where hydrogen is ionized. We hypothesize that all YSOs receive infall onto their outer disks which is steady (or slowly declining with time) and that FU Orionis outbursts are self-regulated, disk outbursts which occur only in systems which transport matter inward at a rate sufficiently high to cause hydrogen to be ionized in the inner disk. We estimate a critical mass flux of dm(sub crit)/dt = 5 x 10(exp 7) solar mass/yr independent of the magnitude of alpha for systems with one solar mass, three solar radius central objects. Infall accretion rates in the range of dm(sub in)/dt = 1-10) x 10(exp -6) solar mass/yr produce observed FU Orionis timescales consistent with estimates of spherical molecular cloud core collapse rates. Modeled ionization fronts are typically initiated near the inner edge of the disk and propogate out to a distance of several tens of stellar radii. Beyond this region, the disk transports mass steadily inward at the supplied constant infall rate. Mass flowing through the innermost disk annulus is equal to dm(sub in)/dt only in a time-averaged sense and is regulated by the ionization of hydrogen in the inner disk such that long intervals (approximately 1000 yr) of low-mass flux: (1-30) x 10(exp -8) solar mass/yr are punctuated by short intervals (approximately 100 yr) of high-mass flux: (1-30) x 10(exp -5) solar mass/yr. Timescales and mass fluxes derived for quiescent and outburst stages are consistent with estimates from observations of T Tauri and FU Orionis systems, respectively.

Bell, K. R.↗

NASA NTRSDate not supplied

X-57 “Maxwell” High-Lift Propeller Testing and Model Development

NASA’s X-57 “Maxwell” distributed electric propulsion flight demonstrator has a high-lift system that includes 12 fixed-pitch high-lift propellers located upstream of the wing leading edge for lift augmentation at low speeds. These high-lift propellers are not required at higher speeds and are folded conformally along the nacelles to reduce drag when not in operation. Aircraft performance models and flight simulations incorporate propeller performance to predict thrust, moments, and power consumption and propeller model accuracy is important in identifying safe operating regimes for this aircraft. Current high-lift propeller performance models have been verified and calibrated against numerous computational fluid dynamics analyses under a variety of flight conditions. We performed a series of full-scale wind tunnel tests at the NASA Langley Research Center Low Speed Aeroacoustic Wind Tunnel to further validate these models, to identify any adverse operating conditions for these propellers, and to assess the accuracy of the facility’s new Propeller Test Stand. The results indicate that the models accurately predicted performance and that the right-handed propeller showed lower torque and thrust for a given propeller speed compared to the left-handed version. Acoustic data support these measurements, showing higher tonal noise for the left versus right propeller. We suspect this is due to slight differences in the material properties between the early production (right) and more recent (left) blade sets leading to greater detwisting in the right-handed blades under load. Both propellers demonstrated very stable operation throughout the test including during deployment, stowing, and windmilling. Furthermore, high-speed imagery of the spinning propeller indicated no blade oscillations or instabilities for any test case. We also leveraged these images to analyze the effects of propeller loading on blade detwisting and tip position. Unfortunately, the thrust measurements varied significantly during the test due to cross-loading of the Propeller Test Stand load cell, though trends in the thrust data were still observable. The torque measurement, however, remained very precise for all test points and was used for performance comparisons. As a result of this test, we validated and improved the X-57 high-lift propeller performance models, obtained detailed propeller acoustic data and high-speed imagery, observed the propeller operating safely during a variety of dynamic events, and identified two potentially adverse, low-propeller-speed conditions which will be avoided during normal aircraft operation.

X-57↗

NASA NTRS2023

Measurements and Computations of Natural Transition on the NASA Juncture-Flow Model with a Symmetric Wing

Experiments were performed in the 14- by 22-Foot Subsonic Tunnel to assess natural transition on the symmetric-airfoil wings of the NASA Juncture-Flow Model. Infrared thermography was used to visualize the heating on the upper surface of both wings of the full-span model, and on the fuselage, for angles of incidence ranging from -10° to 10° at a fixed Reynolds number of 2.4E6 based on the chord length at the wing planform break. The fuselage boundary layer transitioned well upstream of the wing-root leading edge for all conditions. Transition fronts were identified by a steep rise in the surface temperature, and the transition coordinates were transformed from an image-based to a body-fixed system. Additionally, the state of the boundary layer was estimated at pressure ports distributed on the wings through observation of the pressure coefficient as a function of the angle of incidence. For increasing angles of incidence, the transition front was observed to advance upstream, in a mostly spanwise-uniform fashion, from near midchord at α = 0°; however, for increasingly negative angles of incidence, the transition front first receded and then advanced in a nonuniform jagged manner that is typically observed with stationary crossflow. The transition wedges first appeared inboard of the wing break and then spread outboard to near the tip by α = -6°. The upstream shift in transition at positive angles of incidence and the outboard progression of crossflow-dominated transition at increasingly negative angles of incidence are consistent with trends identified in a computational assessment of the boundary-layer transition based on both linear stability analysis and Reynolds-averaged-Navier-Stokes-based transition models. The stability results obtained from the Langley Stability and Transition Analysis Code were used to recalibrate a dual N-factor criterion, which allowed for the prediction of transition fronts that showed excellent agreement with the experiment. The Reynolds-averaged-Navier-Stokes-based models, from the NASA OVERFLOW 2.3 solver, that accounted for the crossflow instability showed mixed results in comparison with the experiment, with the helicity-based Langtry-Menter model performing the best. The experimental data, particularly the cases involving strong influence from both Tollmien-Schlichting and crossflow instabilities, will be valuable for the continued validation and improvement of transition models.

Boundary layer transition↗

NASA NTRS2023

Measurements and Computations of Natural Transition on the NASA Juncture-Flow Model with a Symmetric Wing

Experiments were performed in the 14- by 22-Foot Subsonic Tunnel to assess natural transition on the symmetric-airfoil wings of the NASA Juncture-Flow Model. Infrared thermography was used to visualize the heating on the upper surface of both wings of the full-span model, and on the fuselage, for angles of incidence ranging from -10° to 10° at a fixed Reynolds number of 2.4E6 based on the chord length at the wing planform break. The fuselage boundary layer transitioned well upstream of the wing-root leading edge for all conditions. Transition fronts were identified by a steep rise in the surface temperature, and the transition coordinates were transformed from an image-based to a body-fixed system. Additionally, the state of the boundary layer was estimated at pressure ports distributed on the wings through observation of the pressure coefficient as a function of the angle of incidence. For increasing angles of incidence, the transition front was observed to advance upstream, in a mostly spanwise-uniform fashion, from near midchord at α = 0°; however, for increasingly negative angles of incidence, the transition front first receded and then advanced in a nonuniform jagged manner that is typically observed with stationary crossflow. The transition wedges first appeared inboard of the wing break and then spread outboard to near the tip by α = -6°. The upstream shift in transition at positive angles of incidence and the outboard progression of crossflow-dominated transition at increasingly negative angles of incidence are consistent with trends identified in a computational assessment of the boundary-layer transition based on both linear stability analysis and Reynolds-averaged-Navier-Stokes-based transition models. The stability results obtained from the Langley Stability and Transition Analysis Code were used to recalibrate a dual N-factor criterion, which allowed for the prediction of transition fronts that showed excellent agreement with the experiment. The Reynolds-averaged-Navier-Stokes-based models, from the NASA OVERFLOW 2.3 solver, that accounted for the crossflow instability showed mixed results in comparison with the experiment, with the helicity-based Langtry-Menter model performing the best. The experimental data, particularly the cases involving strong influence from both Tollmien-Schlichting and crossflow instabilities, will be valuable for the continued validation and improvement of transition models.

boundary layer transition↗

NASA NTRS2023

Measurements and Computations of Natural Transition on the NASA Juncture-Flow Model with a Symmetric Wing

Experiments were performed in the 14- by 22-Foot Subsonic Tunnel to assess natural transition on the symmetric-airfoil wings of the NASA Juncture-Flow Model. Infrared thermography was used to visualize the heating on the upper surface of both wings of the full-span model, and on the fuselage, for angles of incidence ranging from -10° to 10° at a fixed Reynolds number of 2.4E6 based on the chord length at the wing planform break. The fuselage boundary layer transitioned well upstream of the wing-root leading edge for all conditions. Transition fronts were identified by a steep rise in the surface temperature, and the transition coordinates were transformed from an image-based to a body-fixed system. Additionally, the state of the boundary layer was estimated at pressure ports distributed on the wings through observation of the pressure coefficient as a function of the angle of incidence. For increasing angles of incidence, the transition front was observed to advance upstream, in a mostly spanwise-uniform fashion, from near midchord at α = 0°; however, for increasingly negative angles of incidence, the transition front first receded and then advanced in a nonuniform jagged manner that is typically observed with stationary crossflow. The transition wedges first appeared inboard of the wing break and then spread outboard to near the tip by α = -6°. The upstream shift in transition at positive angles of incidence and the outboard progression of crossflow-dominated transition at increasingly negative angles of incidence are consistent with trends identified in a computational assessment of the boundary-layer transition based on both linear stability analysis and Reynolds-averaged-Navier-Stokes-based transition models. The stability results obtained from the Langley Stability and Transition Analysis Code were used to recalibrate a dual N-factor criterion, which allowed for the prediction of transition fronts that showed excellent agreement with the experiment. The Reynolds-averaged-Navier-Stokes-based models, from the NASA OVERFLOW 2.3 solver, that accounted for the crossflow instability showed mixed results in comparison with the experiment, with the helicity-based Langtry-Menter model performing the best. The experimental data, particularly the cases involving strong influence from both Tollmien-Schlichting and crossflow instabilities, will be valuable for the continued validation and improvement of transition models.

boundary layer transition↗

NASA NTRS1994

Inner loop flight control for the High-Speed Civil Transport

High-speed aerospace vehicles which employ high strength, light weight, yet deformable materials may exhibit significant interaction between the rigid-body and vibrational dynamics. Preliminary High-Speed Civil Transport (HSCT) configurations are a prime example. Traditionally, separate control systems have been used to augment the rigid-body and vibrational dynamics. In the HSCT arena, the highly coupled motions may not allow this design freedom. The research activity addresses two specific issues associated with the design and development of an integrated flight control system (FCS) for HSCT configurations, which are discussed next. The HSCT is expected to have a short period instability at subsonic speeds. Flight vehicles with this characteristic (i.e., F-16, F-22, X-29, Space Shuttle) are stabilized with what is called a superaugmented pitch rate loop. One concern is 'Will this stability augmentation logic work for a HSCT?' Studies show that an idealized pitch rate design would be acceptable, but is not realistic. Investigations using a contaminated pitch rate design reveal serious hurdles to overcome in the FCS design. Mounting location for the pitch rate sensor is critical. Results indicate a forward location leads to destabilizing pick-up of aeroelastic modes, while aft locations lead to undesirable coupling of the dominate pitch mode with the first aeroelastic mode. Intermediate locations for the sensor may not be acceptable. The source of the problem is the presence of low frequency aeroelastic modes in HSCT configurations, which are not present in vehicles currently using the superaugmented logic. To say the least, a conventional superaugmented pitch rate loop strategy may have undesirable characteristics. An unconventional strategy, which attempts to eliminate the above deficiencies by blending several pitch rate signals, indicates an improvement in the FCS architecture feasibility, but is still lacking in some respects. The HSCT configuration does not have aerodynamic surfaces in the vicinity of the nose (i.e., no canard or vane). A second concern is 'Can the fuselage bending/torsion aeroelastic modes be effectively augmented without sufficient control input near the vehicle nose?' The superaugmented FCS results above may be suggesting the necessity of a secondary feedback loop to achieve an acceptable integrated FCS. Preliminary analysis of HSCT aeroelastic mode shapes indicate the use of existing wing leading edge devices as a second control input may be lacking in control authority for the rigid-body attitude and aeroelastic modes. An effort is underway to incorporate generic wing leading edge devices and canards into a generic HSCT model for the purpose of assessing additional control authority and it's use in candidate FCS designs. A generic HSCT mathematical model was necessary for the studies above. A HSCT category model is available in NASA-CR-172201. This model describes the linear, longitudinal dynamics about the following flight condition: ascent, W = 730,000 lbs, h = 6,500 ft, M = 0.6. The model incorporates the full rigid-body variable set, as well as eighteen aeroelastic modes. Elevator deflection serves as the control input. Modifications to the model include the incorporation of relaxed static stability (i.e., static margin from -7.3% to +10%) and additional control inputs.

Newman, Brett A.↗

NASA NTRS2005

Physics-Based Spectra of Accretion Disks around Black Holes

The purpose of this grant was to begin the process of deriving the light output of accretion disks around black holes directly from the actual processes that inject heat into the accreting matter, rather than from guessed dependences of heating rate on physical parameters. At JHU, the effort has focussed so far on models of accretion onto "intermediate mass black holes", a possible class of black holes, examples of which may have recently been discovered in nearby galaxies. There, Krolik and his student (Yawei Hui) have computed stellar atmospheres for uniformly-heated disks around this class of black holes. Their models serve two purposes: they are the very first serious attempts to compute the spectrum from accreting black holes in this mass range; and a library of such models can be used later in this program as contrasts for those computed on the basis of real disk dynamics. The output from these local disk calculations has also been successfully coupled to a program that applies the appropriate relativistic transformations and computes photon trajectories in order to predict the spectrum received by observers located at different polar angles. The principal new result of these calculations is the discovery of potentially observable ionization edges of H-like C and O at frequencies near the peak in flux from these objects. Most of the grant money at UCSB was spent on supporting graduate student Shane Davis. In addition. some money was spent on supporting two other students: Ari Socrates (now a Hubble Fellow at Princeton), and Laura Melling. Davis spent the year constructing stellar atmosphere models of accretion disks appropriate for the high/soft (thermal) state of black hole X-ray binaries. As with AGN models published previously by our collaboration with NASA support. our models include a complete general relativistic treatment of both the disk structure and the propagation of photons from the disk to a distant observer. They also include all important continuum opacity sources, including Compton scattering and bound-free opacity from abundant metal species. The principal new result is that bound-free opacity is very significant in altering the continuum spectral shape, resulting for example in quite different "color correction factors" compared to those predicted previously. In addition, the models predict a relationship between luminosity and inner disk temperature that is, for the first time, in accord with that observed. The primary purpose of the grant was to incorporate more realistic accretion disk physics, learned largely from simulations, into such spectral models. The Davis et al. paper includes consideration of a vertical dissipation profile computed from radiation magneto-hydrodynamic simulations of MRI turbulence by N. J. Turner (2004). So long as the disk is effectively thick, such dissipation profiles do not affect the predicted spectrum significantly. (More work needs to be done on these simulations, however.) A potentially more serious issue is that MRI turbulence produces substantial inhomogeneities, as do photon bubble instabilities. These inhomogeneities can affect the spectra by enhancing the effects of absorption opacity over scattering opacity. We have done some preliminary Monte Carlo calculations to explore these effects.

Krolik, Julian H.↗

NASA NTRS2018

Implementation of J-A Methodology Elastic-Plastic Crack Instability Analysis Capability into the WARP-3D Code

Characterization of the near crack-tip stress/strain fields is the foundation of fracture mechanics. The description of the near tip stress field and the prediction of when fracture occurs is well established for brittle materials that exhibit linear elastic behavior. However, in ductile materials or conditions that violate linear elastic assumptions (Aluminum alloys, Al 2024-T3, Al 2024- T351 etc.), the elastic-plastic crack-tip stress fields are characterized by the Hutchison-Rice-Rosengren (HRR) field. The J-integral is commonly used to characterize amplitude of the HRR field under elastic-plastic conditions. The J-integral has been demonstrated for crack-tip fields that are under high constraint conditions (i.e., small-scale plasticity where the J-dominance is maintained). However, as the external load increases, yielding changes from small- to largescale plasticity and usually a loss of constraint (i.e., reduction in the triaxial stress field along the crack front). The loss of constraint leads to the deviation of the crack-tip stress fields from that given by the HRR field. Hence, the J-dominance will be gradually lost and additional parameter(s) are required to quantify the crack-tip stress fields and predict fracture behavior. The assessment objectives were to: 1) implement a two-parameter (i.e., J-A) fracture criterion into an elastic-plastic three-dimensional (3D) finite element analysis (FEA), 2) validate the implementation by comparison with the A parameter from literature data, 3) conduct material characterization tests to quantify the material behavior and provide fracture data for validation of the J-A fracture criteria, and (4) perform evaluations to establish if the J-A criteria can be used to predict fracture in a ductile metallic material (e.g., aluminum alloys). The A parameter in these criteria is the second parameter in a three-term elastic-plastic asymptotic expansion of the neartip stress behavior. A series of extensive FEAs were performed using WARP3D software package to obtain solutions for the A parameter for different specimen configurations. The methodology needed for the estimation of the A parameter in the asymptotic expansion was developed and implemented using Matlab®. A user material (UMAT) routine was used to model the material stress-strain response using a Ramberg-Osgood power law with a hardening exponent (n) and a material coefficient (alpha). This UMAT routine was successfully implemented in WARP3D software and validated through comparison with the experimental data. Three configurations were extracted from published results: 1) center cracked plate (CCP), 2) single edge-cracked plate (SECP), and 3) double edge-cracked plate (DECP). These configurations and four other configurations (three-hole tension (THT)), three-point bend (3PTB), three-hole compact tension (3PCT), and compact tension (CT)) were analyzed to verify the methodology that was developed and implemented into WARP3D. Solutions of the A parameter were obtained for remote tension loading conditions that started with small-scale yielding and continued into the large-scale plasticity regime. The results indicate that the methodology developed can be used to calculate the elastic-plastic J-A parameters for test specimens with a range of crack geometries, material strain hardening behaviors, and loading conditions. The J-A parameters were implemented as fracture criteria and used to predict the test results. For comparison, other fracture criteria were used to predict the same test results. Major findings include: The A constraint parameter A varies with specimen type and applied load thus accurate determination is crucial in predicting the failure load, and the A parameter is asymptotic as the failure load is approached, making an accurate determination difficult (i.e., small differences in the A parameter can cause large variations in failure load) for materials exhibiting elastic-plastic behavior. The failure predictions from J-A methodology were more accurate than the traditionally used KC and J methods, and have comparable scatter to that observed when using the crack-tip opening angle (CTOA) method. However, the J-A methodology requires considerable effort (expertise level and labor) to implement and to evaluate the A parameter for different specimen types and materials, or to apply this methodology to part-through crack (e.g., 3D problems) structural applications.

Hamm, Kenneth R., Jr.↗

NASA NTRS2014

Adaptive Augmenting Control Flight Characterization Experiment on an F/A-18

This paper summarizes the Adaptive Augmenting Control (AAC) flight characterization experiments performed using an F/A-18 (TN 853). AAC was designed and developed specifically for launch vehicles, and is currently part of the baseline autopilot design for NASA's Space Launch System (SLS). The scope covered here includes a brief overview of the algorithm (covered in more detail elsewhere), motivation and benefits of flight testing, top-level SLS flight test objectives, applicability of the F/A-18 as a platform for testing a launch vehicle control design, test cases designed to fully vet the AAC algorithm, flight test results, and conclusions regarding the functionality of AAC. The AAC algorithm developed at Marshall Space Flight Center is a forward loop gain multiplicative adaptive algorithm that modifies the total attitude control system gain in response to sensed model errors or undesirable parasitic mode resonances. The AAC algorithm provides the capability to improve or decrease performance by balancing attitude tracking with the mitigation of parasitic dynamics, such as control-structure interaction or servo-actuator limit cycles. In the case of the latter, if unmodeled or mismodeled parasitic dynamics are present that would otherwise result in a closed-loop instability or near instability, the adaptive controller decreases the total loop gain to reduce the interaction between these dynamics and the controller. This is in contrast to traditional adaptive control logic, which focuses on improving performance by increasing gain. The computationally simple AAC attitude control algorithm has stability properties that are reconcilable in the context of classical frequency-domain criteria (i.e., gain and phase margin). The algorithm assumes that the baseline attitude control design is well-tuned for a nominal trajectory and is designed to adapt only when necessary. Furthermore, the adaptation is attracted to the nominal design and adapts only on an as-needed basis (see Figure 1). The MSFC algorithm design was formulated during the Constellation Program and reached a high maturity level during SLS through simulation-based development and internal and external analytical review. The AAC algorithm design has three summary-level objectives: (1) "Do no harm;" return to baseline control design when not needed, (2) Increase performance; respond to error in ability of vehicle to track command, and (3) Regain stability; respond to undesirable control-structure interaction or other parasitic dynamics. AAC has been successfully implemented as part of the Space Launch System baseline design, including extensive testing in high-fidelity 6-DOF simulations the details of which are described in [1]. The Dryden Flight Research Center's F/A-18 Full-Scale Advanced Systems Testbed (FAST) platform is used to conduct an algorithm flight characterization experiment intended to fully vet the aforementioned design objectives. FAST was specifically designed with this type of test program in mind. The onboard flight control system has full-authority experiment control of ten aerodynamic effectors and two throttles. It has production and research sensor inputs and pilot engage/disengage and real-time configuration of up to eight different experiments on a single flight. It has failure detection and automatic reversion to fail-safe mode. The F/A-18 aircraft has an experiment envelope cleared for full-authority control and maneuvering and exhibits characteristics for robust recovery from unusual attitudes and configurations aided by the presence of a qualified test pilot. The F/A-18 aircraft has relatively high mass and inertia with exceptional performance; the F/A-18 also has a large thrust-to-weight ratio, owing to its military heritage. This enables the simulation of a portion of the ascent trajectory with a high degree of dynamic similarity to a launch vehicle, and the research flight control system can simulate unstable longitudinal dynamics. Parasitic dynamics such as slosh and bending modes, as well as atmospheric disturbances, are being produced by the airframe via modification of bending filters and the use of secondary control surfaces, including leading and trailing edge flaps, symmetric ailerons, and symmetric rudders. The platform also has the ability to inject signals in flight to simulate structural mode resonances or other challenging dynamics. This platform also offers more test maneuvers and longer maneuver times than a single rocket or missile test, which provides ample opportunity to fully and repeatedly exercise all aspects of the algorithm. Prior to testing on an F/A-18, AAC was the only component of the SLS autopilot design that had not been flight tested. The testing described in this paper raises the Technology Readiness Level (TRL) early in the SLS Program and is able to demonstrate its capabilities and robustness in a flight environment.

VanZwieten, Tannen S.↗