Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrode microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Improve photovoltaic performance of titanium dioxide nanorods based dye-sensitized solar cells by Ca-doping

Highlights: • TiO{sub 2} nanorods doped with Ca ions were synthesized by one-step hydrothermal method. • The flat band edge of rutile TiO{sub 2} shifted positively via Ca-doping. • The photoelectric conversion efficiency of dye-sensitized solar cells (DSSCs) based on TiO{sub 2} electrode was much enhanced by Ca-doping. • A relatively high open circuit voltage was obtained by adopting Ca-doped TiO{sub 2} nanorods electrode. - Abstract: Ca-doped TiO{sub 2} nanorod arrays were prepared via the one-step hydrothermal method successfully, and the effect of Ca ions content on the photovoltaic conversion efficiency of dye-sensitized solar cells has been fully discussed in the paper. Although no obvious change on the microstructure and morphology was observed by field emission scanning electron microscope and transmission electron microscope for the Ca-doped samples, the results of X-ray diffraction and X-ray photoelectron spectroscopy confirmed that Ti{sup 4+} was substituted with Ca{sup 2+} successfully. UV–vis spectroscopy results revealed that the flat band edge shifted positively by Ca ions doping. The photovoltaic conversion efficiency of the dye-sensitized solar cells based on the 2 mol% Ca-doped TiO{sub 2} electrode was 43% higher than that of the undoped one due to the less recombination possibility.

36 MATERIALS SCIENCE↗

Synchrotron small-angle X-ray scattering technique for battery electrode study

Structure dependent stability is a concern for the achievement of high energy density electrode with long cycling lifetime, especially for alloying-type and conversion-type anodes. Substantial alterations in volume upon discharge-discharge process leads to particle pulverization and continuous consumption of electrolyte. Moreover, the nucleation and growth mechanism of Li 2 O and Li 2 S, which determines the rate performance of Li-O 2 and Li-S batteries, are still understudy. Microstructure characterization techniques have been applied to disclose the structural changes of active material at different charge/discharge states. Synchrotron small-angle X-ray scattering (SAXS) attracts considerable attention because of the high flux, high time resolution and nondestructive characteristics. In addition, SAXS patterns provide statistics structural information of electrode at micrometer scale. The commonly used coin cell with punched holes simplifies the application of in situ/operando SAXS measurement. Here, this review discusses the research about the SAXS technique in the characterization of electrode in different batteries.

25 ENERGY STORAGE↗

The augmented saddle field discharge characteristics and its applications for plasma enhanced chemical vapour deposition

A high ion flux parallel electrode plasma is proposed and studied in its DC configuration. By cascading a diode source region which supplies electrons and a saddle field region where these seed electrons are energized and amplified, the energy of ion bombardment on the substrate can be decoupled from the plasma density. The sufficiently large density of electrons and holes in the vicinity of the substrate raises the possibility to perform plasma enhanced chemical vapour deposition on insulating materials, at low sheath voltages (around 40 V in the configuration studied), at low temperatures in which the surface mobility of film growth species may be provided by the bombardment of moderate energy ions. As a benchmarking exercise, experiments are carried out on silane discharge characteristics and deposition of hydrogenated amorphous silicon (a-Si:H) on both silicon wafer and glass. The films grown at low anode voltages have excellent microstructures with predominantly monohydride bonds, sharp band tails, but relatively high integrated defect density in the mid 10{sup 16}/cm{sup 3} range for the particular substrate temperature of 180 Degree-Sign C, indicating that further optimizations are necessary if the electrode configuration is to be used to create a-Si:H devices.

36 MATERIALS SCIENCE↗

Evaluating the improvement of corrosion residual strength by adding 1.0 wt.% yttrium into an AZ91D magnesium alloy

The influence of yttrium on the corrosion residual strength of an AZ91D magnesium alloy was investigated detailedly. Scanning electron microscope was employed to analyze the microstructure and the fractography of the studied alloys. The microstructure of AZ91D magnesium alloy is remarkably refined due to the addition of yttrium. The electrochemical potentiodynamic polarization curve of the studied alloy was performed with a CHI 660b electrochemical station in the three-electrode system. The result reveals that yttrium significantly promotes the overall corrosion resistance of AZ91D magnesium alloy by suppressing the cathodic reaction in corrosion process. However, the nucleation and propagation of corrosion pits on the surface of the 1.0 wt.% Y modified AZ91D magnesium alloy indicate that pitting corrosion still emerges after the addition of yttrium. Furthermore, stress concentration caused by corrosion pits should be responsible for the drop of corrosion residual strength although the addition of yttrium remarkably weakens the effect of stress concentration at the tip of corrosion pits in loading process.

36 MATERIALS SCIENCE↗

Formation of Sn–M (M=Fe, Al, Ni) alloy nanoparticles by DC arc-discharge and their electrochemical properties as anodes for Li-ion batteries

A direct current arc-discharge method was applied to prepare the Sn–M (M=Fe, Al, Ni) bi-alloy nanoparticles. Thermodynamic is introduced to analyze the energy circumstances for the formation of the nanoparticles during the physical condensation process. The electrochemical properties of as-prepared Sn–M alloy nanoparticles are systematically investigated as anodes of Li-ion batteries. Among them, Sn–Fe nanoparticles electrode exhibits high Coulomb efficiency (about 71.2%) in the initial charge/discharge (257.9 mA h g{sup −1}/366.6 mA h g{sup −1}) and optimal cycle stability (a specific reversible capacity of 240 mA h g{sup −1} maintained after 20 cycles) compared with others. Large differences in the electrochemical behaviors indicate that the chemical composition and microstructure of the nanoparticles determine the lithium-ion storage properties and the long-term cyclic stability during the charge/discharge process. - Graphical abstract: The growth mechanism and electrochemical performance of Sn-based alloy nanoparticles. - Highlights: • Thermodynamic analyses of oxides on Sn-M nanoparticles surface. • The relationship between chemical components and electrochemical responses. • Sn-Fe nanoparticles show excellent electrode performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Influence of electrospraying parameters on the microstructure of La{sub 0.6}Sr{sub 0.4}Co{sub 0.2}F{sub 0.8}O{sub 3-{delta}} films for SOFCs

Ceramics can play a remarkable role in the engineering of intermediate temperature solid oxide fuel cells (IT-SOFCs) capable of meeting the ambitious targets of reduced cost and improved lifetime. While mixed ionic-electronic conductors such as La{sub x}Sr{sub 1-x}Co{sub y}Fe{sub 1-y}O{sub 3-{delta}} are being used as volumic cathodes to increase the catalytic performance of these components, adequate microstructures are also an important requirement for optimal performance, particularly at lower operating temperatures. This work is devoted to the fabrication of La{sub 0.6}Sr{sub 0.4}Co{sub 0.2}Fe{sub 0.8}O{sub 3-{delta}} films on Ce{sub 0.9}Gd{sub 0.1}O{sub 2-{delta}} substrates by electrostatic spray deposition (ESD) and to the characterization of the microstructural dependence on the deposition conditions. A wide variety of microstructures ranging from dense to porous, with particular features such as reticulation and micro-porosity, were obtained by varying the ESD deposition parameters: nozzle-to-substrate distance (15, 30, 43, 45, and 58 mm), solution flow rate (0.34 and 1.5 mL/h), and substrate temperature (300, 350, 400 and 450 deg. C). The correlation between deposition parameters and resulting microstructures was systematically studied and put into evidence. - Graphical Abstract: This work is devoted to the fabrication of La{sub 0.6}Sr{sub 0.4}Co{sub 0.2}Fe{sub 0.8}O{sub 3-{delta}} films on dense Ce{sub 0.9}Gd{sub 0.1}O{sub 2-{delta}} substrates by electrostatic spray deposition (ESD) and to the characterization of the microstructural dependence on the deposition conditions. A wide variety of microstructures ranging from dense to porous, with particular features such as reticulation and micro-porosity, were obtained by varying the nozzle-to-substrate distance, substrate temperature and solution flow rate.Cross-section view of the fractal-like La{sub 0.6}Sr{sub 0.4}Co{sub 0.2}Fe{sub 0.8}O{sub 3-{delta}} cathode film, as-deposited by electrostatic spray deposition.

36 MATERIALS SCIENCE↗

Spatially resolved probing of Preisach density in polycrystalline ferroelectric thin films

Applications of the ferroelectric materials for the information storage necessitate the understanding of local switching behavior on the level of individual grains and microstructural elements. In particular, implementation of multilevel neuromorphic elements requires the understanding of history-dependent polarization responses. Here, we introduce the spatially resolved approach for mapping local Preisach densities in polycrystalline ferroelectrics based on first-order reversal curve (FORC) measurements over spatially resolved grid by piezoresponse force spectroscopy using tip-electrode. The band excitation approach allowed effective use of cantilever resonances to amplify weak piezoelectric signal and also provided insight in position-, voltage-, and voltage history-dependent mechanical properties of the tip-surface contact. Several approaches for visualization and comparison of the multidimensional data sets formed by FORC families or Preisach densities at each point are introduced and compared. The relationship between switching behavior and microstructure is analyzed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Low-Cost Production of Lithium-Ion Separator Membranes w/ Improved Safety

The purpose of this Cooperative Research and Development Agreement (CRADA) between Oak Ridge National Laboratory (ORNL) and Porous Power Technologies, LLC (PPT) was to validate the performance, durability, and safety of a new type of reinforced, composite lithium ion battery separator produced as either a free-standing product or by a method of direct coating after electrode fabrication. ORNL’s primary roles were to develop novel separator thermophysical and mechanical property characterization methods and assist with fundamental understanding of SYMMETRIX® HPX and HPX-F product line chemical makeup and microstructure. PPT’s primary roles were to implement the understanding gained from the ORNL developed characterization methods into a refined product line featuring nonwoven-reinforced, ceramic-filled composite HPX-F separators for the lithium ion battery industry and quantify long-term cell performance improvements associated with HPX-F separators. Over the course of this CRADA, the product line of PPT was expanded from a pure polyvinylidene fluoride (PVDF) HP and polyester nonwoven-reinforced HPX separator platform to one that includes a variety of ceramic-filled HPX-F separators. In addition, the laminating and direct coating technologies for HPX and HPX-F separators are now more developed and moving towards commercial licensing. PPT’s SYMMETRIX® production process will revolutionize the production of lithium ion batteries by eliminating one of the most expensive components (the free-standing separator membrane) while improving performance and safety. The performance and safety improvements are due primarily to replacement of the conventional polyethylene/polypropylene (PE/PP) separator material with polyvinylidene fluoride (PVDF), and to ceramic materials added to the PVDF to form a short-resistant, thermally-stable composite structure. Ultimately, lithium ion battery manufacturers will be able to produce PPT separators in-house through the laminating or direct coating methods such as those based on the SYMMETRIX® product line, giving them higher performance cells at a fraction of the cost required to purchase separators from existing vendors. Direct coating of separators onto electrodes eliminates the cost of a downstream thermal lamination step and requires little or no change to existing equipment. It is a clear path for lithium ion battery manufacturers to reach the <$1/m2 separator price target set by the U.S. Advanced Battery Consortium (USABC). The technology enabled by this project will have a substantial impact on energy efficiency required to produce cells and is anticipated to save up to $1B annually by 2014 in reduced manufacturing costs. In addition, it will contribute significantly to production energy savings associated with transporting free-standing polyolefin (PE/PP) separators from the vendor to the cell manufacturer locations. SYMMETRIX® separators have shown increased cell capacity, improved thermal stability, and longer cycle life over their PE/PP counterparts and have been repeatedly demonstrated to improve nearly all aspects of lithium ion battery performance Prior to the start of this CRADA, widespread adoption has been limited by three factors: 1) difficulty in handling the material on high-speed processing equipment due to lower tensile strength than oriented PE/PP materials; 2) cost concerns associated with the higher expense of PVDF as a raw material; and 3) questions regarding short resistance and durability. The first factor was addressed through thorough mechanical (ultimate tensile strength and dynamic mechanical analysis, etc.) property characterization of HPX and HPX-F materials against the commercial polyolefin baselines. The second factor was address by shifting the focus of PPT’s product line towards the HPX-F materials with low-PVDF (high ceramic filler) content to reduce overall separator cost. Concerns associated with the third factor were alleviated by evaluating the internal shorting resistance of the separators using a custom developed ORNL measurement method and obtaining long-term cycling data of the new HPX-F separator formulations. A materials emphasis was placed on polyester fiber mats for the nonwoven reinforcement (to boost overall separator tensile strength) and proprietary metal oxides for the HPX-F fillers (to improve thermomechanical properties of the separator and make it more resistant to overcharge and internal shorting).

batteries↗

A leaf-molded transparent triboelectric nanogenerator for smart multifunctional applications

Transparent, flexible and highly efficient portable power sources are essential components of the next generation electronics and optoelectronic devices. However, complicated technology, expensive cost, environmental pollution and low-efficient output have limited its development. Herein, based on periodic contact/separation between human skin and the microstructured polydimethylsiloxane (PDMS) film, we demonstrate a transparent flexible triboelectric nanogenerator (TENG) through a relatively simple, low-cost, environmental-friendly and high-efficient method. For the first time, the natural leaves with rich surface textures were introduced to make microstructures on PDMS films as effective friction surface in the TENG. Furthermore, long silver nanowires (200 µm in length at least) through novel synthesis were assembled as high-performance electrode, resulting in the entirely flexible and transparent TENG. Owing to the unique design, the transparent flexible TENG was eventually obtained with an enhanced output (Voc=56 V; Isc=3.1 μA) and remarkable transparency (88%). Owing to compelling features of the TENG, a self-powered user-interactive wearable system was successfully established by integrating a flexible electrochromic device (ECD). The remarkable color-tunable ability via mechanical control of our system, highly inspired by chameleons, is potentially useful in military camouflage, monitoring human activity visually, as well as replacing performance of face change in Sichuan Opera. Therefore, this research is a substantial advancement toward the construction of transparent nanogenerator and its multifunctional applications in energy conversation, wearable electronics, healthcare, culture experience, and even environmental protection.

42 ENGINEERING↗

The Synthesis of Manganese Hydroxide Nanowire Arrays for a High-Performance Zinc-Ion Battery

The morphology, microstructure as well as the orientation of cathodic materials are the key issues when preparing high-performance aqueous zinc-ion batteries (ZIBs). In this paper, binder-free electrode Mn(OH)2 nanowire arrays were facilely synthesized via electrodeposition. The nanowires were aligned vertically on a carbon cloth. The as-prepared Mn(OH)2 nanowire arrays were used as cathode to fabricate rechargeable ZIBs. The vertically aligned configuration is beneficial to electron transport and the free space between the nanowires can provide more ion-diffusion pathways. As a result, Mn(OH)2 nanowire arrays yield a high specific capacitance of 146.3 Ma h g−1 at a current density of 0.5 A g−1. They also demonstrates ultra-high diffusion coefficients of 4.5 × 10−8~1.0 × 10−9 cm2 s−1 during charging and 1.0 × 10−9~2.7 × 10−11 cm−2 s−1 during discharging processes, which are one or two orders of magnitude higher than what is reported in the studies. Furthermore, the rechargeable Zn//Mn(OH)2 battery presents a good capacity retention of 61.1% of the initial value after 400 cycles. This study opens a new avenue to boost the electrochemical kinetics for high-performance aqueous ZIBs.

25 ENERGY STORAGE↗

A general solution-chemistry route to the synthesis LiMPO{sub 4} (M=Mn, Fe, and Co) nanocrystals with [010] orientation for lithium ion batteries

A general and efficient solvothermal strategy has been developed for the preparation of lithium transition metal phosphate microstructures (LiMnPO{sub 4}, LiFePO{sub 4}, and LiCoPO{sub 4}), employing ethanol as the solvent, LiI as the Li source, metal salts as the M sources, H{sub 3}PO{sub 4} as the phosphorus source, and poly(vinyl pyrrolidone) (PVP) as the carbon source and template. This route features low cost, environmental benign, and one-step process for the cathode material production of Li-ion batteries without any complicated experimental setups and sophisticated operations. The as-synthesized LiMPO{sub 4} microstructures exhibit unique, well-shaped and favorable structures, which are self-assembled from microplates or microrods. The b axis is the preferred crystal growth orientation of the products, resulting in a shorter lithium ion diffusion path. The LiFePO{sub 4} microstructures show an excellent cycling stability without capacity fading up to 50 cycles when they are used as a cathode material in lithium-ion batteries. - Graphical abstract: A general and efficient solvothermal strategy has been developed for the preparation of lithium transition metal phosphate microstructures under solvothermal conditions in the presence of PVP. Highlights: > A general and efficient solvothermal strategy has been developed for the preparation of LiMPO{sub 4} microstructures. > This route features low cost, environmental benign, and one-step process. > The LiMPO{sub 4} microstructures exhibit unique, well-shaped, and favorable structures. > The LiFePO{sub 4} microstructures show an excellent cycling stability up to 50 cycles as a cathode material of lithium-ion batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of the graphite electrode material on the characteristics of molten salt electrolytically produced carbon nanomaterials

The electrochemical erosion of a graphite cathode during the electrolysis of molten lithium chloride salt may be used for the preparation of nano-structured carbon materials. It has been found that the structures and morphologies of these carbon nanomaterials are dependent on those of the graphite cathodes employed. A combination of tubular and spherical carbon nanostructures has been produced from a graphite with a microstructure of predominantly planar micro-sized grains and a minor fraction of more irregular nano-sized grains, whilst only spherical carbon nanostructures have been produced from a graphite with a microstructure of primarily nano-sized grains. Based on the experimental results, a best-fit regression equation is proposed that relates the crystalline domain size of the graphite reactants and the carbon products. The carbon nanomaterials prepared possess a fairly uniform mesoporosity with a sharp peak in pore size distribution at around 4 nm. The results are of crucial importance to the production of carbon nanomaterials by way of the molten salt electrolytic method. - Highlights: {yields} Carbon nanomaterials are synthesised by LiCl electrolysis with graphite electrodes. {yields} The degree of crystallinity of graphite reactant and carbon product are related. {yields} A graphite reactant is identified that enables the preparation of carbon nanotubes. {yields} The carbon products possess uniform mesoporosity with narrow pore size distribution.

36 MATERIALS SCIENCE↗

On the possibility of electrochemical unzipping of multiwalled carbon nanotubes to produce graphene nanoribbons

Highlights: • MWCNTs synthesized and electrochemically oxidized to study the formation of GNR • HRTEM, Raman and XPS confirmed no successful unzipping occurred after oxidation • Electrochemical oxidation very unlikely facilitate formation of intercalated MWCNTs - Abstract: Multiwalled carbon nanotubes (MWCNTs) with different geometrical characteristics and chemical doping have been synthesized and electrochemically oxidized to study the possibility of unzipping, and creating graphene nanoribbon (GNR) nanostructures. Modified glassy carbon electrodes of the MWCNTs have been tested in an aqueous electrolyte via anodic scans in a wide range of potentials, followed by keeping at the maximum potential for different times. The microstructural features, structural defects, and functional groups and their elements have been then studied using high resolution transmission electron microscopy (HRTEM), Raman spectroscopy and X-ray photoelectron spectroscopy (XPS), respectively. All results have confirmed that no successful unzipping occurs in the MWCNTs after electrochemical oxidation, even for the nitrogen-doped MWCNTs (CN{sub x}-MWCNTs) with reactive nitrogen groups and defective bamboo structures. In contrast to the report by Shinde et al. (J. Am. Chem. Soc. 2011, 133, 4168–4171), it has been concluded that the electrochemical oxidation in aqueous electrolytes is very unlikely to facilitate sufficient incorporation of the intercalated molecules among the walls of the MWCNTs. These molecules are, however, responsible for unzipping of MWCNTs.

36 MATERIALS SCIENCE↗

Reaction Current Heterogeneity at the Interface between a Lithium Electrode and Polymer/Ceramic Composite Electrolytes

Although lithium metal anodes are expected to increase the energy density of next-generation batteries, dendrite growth during charge remains a major bottleneck preventing widespread implementation. Composite solid electrolytes with ceramic particles embedded in a polymer matrix have the potential to prevent dendrites owing to the higher mechanical stiffness while also possessing the flexibility to maintain contact with the electrode. However, microscopically, the different mechanical and electrochemical properties of the polymer and ceramic domains can cause inhomogeneous charge transfer at the Li/electrolyte interface, which can lead to nonuniform Li deposition and propagation of dendrites. Here, we computationally examine the coupled electrochemical, transport, and mechanical processes at the interface to determine the propensity for dendrite formation and possible approaches to mitigate this issue. Predictions of two possible microstructures at the interface, namely, (i) where both the polymer and ceramic come in contact with Li metal and (ii) when only the polymer comes in contact with Li metal, suggest that the former has a greater tendency for nonuniform plating. In addition, predictions suggest that minimizing the interfacial resistance between polymers and ceramics and incorporating interlayers between the electrode and electrolyte help mitigate current heterogeneity. In conclusion, these predictions provide guidance for experimental approaches to prevent dendrites in composite electrolytes.

25 ENERGY STORAGE↗

Novel High Temperature Carbide and Boride Ceramics for Direct Power Extraction Electrode Applications. Final report

The current project aims to develop new carbide and boride ceramic materials that incorporate different metal elements (e.g., (Hf 1-x Zr x )B 2 , also called ceramic solid solutions) and understand the fundamental composition-processing-structure-property relationships for such materials. Specifically, nano powders and related nano-composites for selected mixed metal carbide and boride materials are synthesized from nano-scale mixed precursors obtained from solution-based processing via heat treatment in inert atmosphere. The obtained fine powders were then consolidated into dense ceramics via a novel flash sintering process. The mechanical properties and thermal oxidation resistance for the obtained materials were evaluated for these materials. It was found that different synthesis routes produced powders with somewhat different characteristics in terms of composition and microstructure, which then led to different properties for the final ceramics. The synthesis and processing methods demonstrated in this study might be adopted for developing other similar high temperature ceramics, while the mixed metal or solid solution ceramic materials obtained from this study might be used as hot electrodes for direction power extraction and other energy-related applications.

20 FOSSIL-FUELED POWER PLANTS↗