SEARCH · Search NASA

Results for “flaps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

All sources NASA NTRS DOE OSTI

NASA NTRS1972

A preliminary evaluation of noise reduction potential for the upper surface blown flap

An assessment of the basic acoustic characteristics and noise reduction potential of an upper surface blown flap consisting of a rectangular nozzle and a single turning flap which was designed to approximate a typical takeoff setting is presented. The noise reduction concepts studied were: (1) replacing a section of the flap trailing edge with a porous material and (2) active modification of the flow field using blowing near the trailing edge. Diagrams of the airfoil section and test equipment are provided. Photographs of airflow conditions across the aerodynamic surface are included.

Hayden, R. E.↗

NASA NTRS1973

Results of Full-Scale Wind Tunnel Tests on the H.126 Jet Flap Aircraft

The aerodynamic characteristics of the full-scale H.126 jet flap aircraft were studied in a 40- by 80 foot wind tunnel. The H.126 aircraft is designed for research on flight characteristics of an aircraft using the jet flap principle. Static longitudinal, lateral, and directional characteristics were measured at a Reynolds number of 2.5 to 2.7 million. The jet control power as well as the aerodynamic characteristics were measured and are presented herein with limited discussion. The primary configuration variables were flap and aileron deflection.

Aiken, T. N.↗

NASA NTRS1973

Low-speed wind tunnel investigation of a semispan STOL jet transport wing body with an upper surface blown jet flap

An investigation of the static longitudinal aerodynamic characteristics of a semispan STOL jet transport wing-body with an upper-surface blown jet flap for lift augmentation was conducted in a low-speed wind tunnel having a 12-ft octagonal test section. The semispan swept wing had an aspect ratio of 3.92 (7.84 for the full span) and had two simulated turbofan engines mounted ahead of and above the wing in a siamese pod equipped with an exhaust deflector. The purpose of the deflector was to spread the engine exhaust into a jet sheet attached to the upper surface of the wing so that it would turn downward over the flap and provide lift augmentation. The wing also had optional boundary-layer control provided by air blowing through a thin slot over a full-span plain trailing-edge flap.

Phelps, A. E., III↗

NASA NTRS1972

Random gust response statistics for coupled torsion-flapping rotor blade vibrations.

An analysis of coupled torsion-flapping rotor blade vibrations in response to atmospheric turbulence revealed that at high rotor advance ratios anticipated for future high speed pure or convertible rotorcraft both flapping and torsional vibrations can be severe. While appropriate feedback systems can alleviate flapping, they have little effect on torsion. Dynamic stability margins have also no substantial influence on dynamic torsion loads. The only effective means found to alleviate turbulence caused torsional vibrations and loads at high advance ratio was a substantial torsional stiffness margin with respect to local static torsional divergence of the retreating blade.

Gaonkar, G. H.↗

NASA NTRS1973

Conformal mapping for potential flow about airfoils with attached flap.

The conformal mapping sequence presented transforms the potential flow about a circle into that about an airfoil with an attached flap or spoiler. It is found that adequate versatility of the flap shape for a given airfoil can usually be obtained with the indicated functions, although other transformations would expand the variety of possible flap shapes.

Rossow, V. J.↗

NASA NTRS1973

Design and fabrication of an aeroelastic flap element for a Short TakeOff and Landing (STOL) aircraft model

A flap element typifying a third element in the flap system of a short takeoff and landing aircraft was designed, fabricated, and instrumented. It was delivered to NASA for flight-simulated testing. The flap element was aluminum skin-stringer-rib construction with adhesive laminated skins. The tests conducted were as follows: (1) sonic check, (2) thermal expansion, (3) end fitting stiffness, (4) material properties, (5) maximum bending stress in the skin, and (6) effective skin width and stringer spacing.

Belleman, G. W.↗

NASA NTRS1973

Concepts for a theoretical and experimental study of lifting rotor random loads and vibrations (further experiments with progressing/regressing rotor flapping modes), Phase 7-C

The experiments with progressing/regressing forced rotor flapping modes have been extended in several directions and the data processing method has been considerably refined. The 16 inch hingeless 2-bladed rotor model was equipped with a new set of high precision blades which removed previously encountered tracking difficulties at high advance ratio, so that tests up to .8 rotor advance ratio could be conducted. In addition to data with 1.20 blade natural flapping frequency data at 1.10 flapping frequency were obtained. Outside the wind tunnel, tests with a ground plate located at different distances below the rotor were conducted while recording the dynamic downflow at a station .2R below the rotor plane with a hot wire anemometer.

Hohenemser, K. H.↗

NASA NTRS1973

Acoustic characteristics of a large-scale wind tunnel model of an upper-surface blown flap transport having two engines

The upper-surface blown (USB) flap as a powered-lift concept has evolved because of the potential acoustic shielding provided when turbofan engines are installed on a wing upper surface. The results from a wind tunnel investigation of a large-scale USB model powered by two JT15D-1 turbofan engines are-presented. The effects of coanda flap extent and deflection, forward speed, and exhaust nozzle configuration were investigated. To determine the wing shielding the acoustics of a single engine nacelle removed from the model were also measured. Effective shielding occurred in the aft underwing quadrant. In the forward quadrant the shielding of the high frequency noise was counteracted by an increase in the lower frequency wing-exhaust interaction noise. The fuselage provided shielding of the opposite engine noise such that the difference between single and double engine operation was 1.5 PNdB under the wing. The effects of coanda flap deflection and extent, angle of attack, and forward speed were small. Forward speed reduced the perceived noise level (PNL) by reducing the wing-exhaust interaction noise.

Falarski, M. D.↗

NASA NTRS1974

Preliminary static tests of a simulated upper-surface blown jet-flap configuration utilizing a full-size turbofan engine

The investigation was conducted to evaluate the static turning performance and the pressure and temperature environment of an upper-surface-blown wing and flap utilizing a small turbofan engine. The tests involved modifications of the engine primary nozzle designed to alleviate high temperature problems on the wing and flaps and yet provide acceptable static turning performance over the desired range of flap deflections and thrust conditions.

Shivers, J. P.↗

NASA NTRS1974

Externally blown flap noise research

The Lewis Research Center cold-flow model externally blown flap (EBF) noise research test program is summarized. Both engine under-the-wing and over-the-wing EBF wing section configurations were studied. Ten large scale and nineteen small scale EBF models were tested. A limited number of forward airspeed effect and flap noise suppression tests were also run. The key results and conclusions drawn from the flap noise tests are summarized and discussed.

Dorsch, R. G.↗

NASA NTRS1974

Small scale model static acoustic investigation of hybrid high lift systems combining upper surface blowing with the internally blown flap

A static acoustic and propulsion test of a small radius Jacobs-Hurkamp and a large radius Flex Flap combined with four upper surface blowing (USB) nozzles was performed. Nozzle force and flow data, flap trailing edge total pressure survey data, and acoustic data were obtained. Jacobs-Hurkamp flap surface pressure data, flow visualization photographs, and spoiler acoustic data from the limited mid-year tests are reported. A pressure ratio range of 1.2 to 1.5 was investigated for the USB nozzles and for the auxiliary blowing slots. The acoustic data were scaled to a four-engine STOL airplane of roughly 110,000 kilograms or 50,000 pounds gross weight, corresponding to a model scale of approximately 0.2 for the nozzles without deflector. The model nozzle scale is actually reduced to about .17 with deflector although all results in this report assume 0.2 scale factor. Trailing edge pressure surveys indicated that poor flow attachment was obtained even at large flow impingement angles unless a nozzle deflector plate was used. Good attachment was obtained with the aspect ratio four nozzle with deflector, confirming the small scale wind tunnel tests.

Cole, T. W.↗

NASA NTRS1974

Gust alleviation for a STOL transport by using elevator, spoilers, and flaps

Control laws were developed to investigate methods of alleviating the response of a STOL transport to gusty air. The transport considered in the study had triple-slotted, externally blown jet flaps and a large T-tail. The control devices used were the elevator, spoilers, and flaps. A hybrid computing system was used to simulate linearized longitudinal dynamics of the aircraft and to implement a conjugate gradient optimal search algorithm. The aircraft was simulated in the low-speed approach condition only. Feedback control matrices were found which minimized the average of a quadratic functional involving passenger compartment accelerations, pitch angle and rate, flight path angle and speed variations. The optimization was performed for artificially designed gust inputs in the form of predetermined rectangular waveforms. Results were obtained for elevator, spoilers, and flaps acting singly and in combination. Additional results were obtained for unit sinusoidal gust inputs by using the gain matrices computed for the artificial test gusts. Various sensor configurations were also investigated.

Lallman, F. J.↗

NASA NTRS1974

Longitudinal aerodynamic characteristics of an externally blown flap powered lift model with several propulsive system simulators

An investigation of a four-engine externally blown flap (EBF) powered-lift transport was conducted in the Langley V/STOL tunnel to determine the effect of different engine configurations on the longitudinal aerodynamic characteristics. The different engine configurations were simulated by five different sets of propulsion simulators on a single aircraft model. Longitudinal aerodynamic data were obtained for each simulator on each flap deflection corresponding to cruise, take-off, and landing at a range of angles of attack and various thrust coefficients. The bypass ratio (BPR) 6.2 engine simulator provided the best lift and drag characteristics of the five simulators tested in the take-off and landing configurations. The poor performance of the BPR 10.0 and 3.2 engine simulators can be attributed to a mismatch of engine-model sizes or poor engine location and orientation. Isolated engine wake surveys indicated that a reasonable assessment of the aerodynamic characteristics of an engine-wing-flap configuration could be made if qualitative information were available which defined the engine wake characteristics. All configurations could be trimmed easily with relatively small horizontal-tail incidence angles; however, the take-off landing configurations required a high-lift tail.

Hoad, D. R.↗

NASA NTRS1973

Studies of a large-scale jet-flap rotor in the 40- by 80-foot wind tunnel

Description of a large scale rotor and its apparatus which were constructed to investigate the merits of jet-flap applications to helicopter rotors. The presented results of a wind-tunnel study, aimed at determining the jet-flap multicyclic control potential for vibratory load and stress relief, illustrate the types of control deflections involved and their effects. A demonstrated analysis technique, which is used to analyze these results, is believed to be applicable to many kinds of investigations, particularly where large numbers of variables are involved and where circumstances tend to preclude 'systematic' testing. Among the major results of the study is the finding that significant and substantial vibratory stress and load reductions are achievable with a jet-flap multicyclic control system.

Mccloud, J. L., III↗

NASA NTRS1974

Externally blown flap noise research

Dorsch, R. G.↗

NASA NTRS1974

A wind tunnel investigation of the wake near the trailing edge of a deflected externally blown flap

The model tested was a general research model of a swept-wing, jet-powered STOL transport with externally blown flaps. The model was tested with four engine simulators mounted on pylons under the wing. Tests were conducted in the V/STOL tunnel over an angle of attack range of 0 deg to 16 deg and a thrust coefficient range from 0 to approximately 4 at a Reynolds number of 0.461 x 1 million based on the wing reference chord. The results of this investigation are presented primarily as plots of the individual velocity vectors obtained from the wake survey. These data are used to extend an earlier analysis to isolate the effects of the engine thrust on the behavior of the flow at the flap trailing edge. Results of a comparison with a jet-flap theory are also shown.

Johnson, W. G., Jr.↗

NASA NTRS1975

Static tests of a simulated upper surface blown jet-flap configuration utilizing a full-size turbofan engine

The investigation utilizing a small turbofan engine was conducted to evaluate static turning performance and pressure and temperature environment of an upper surface blown wing and flap segment. The tests involved modifications of the engine primary nozzle to alleviate high-temperature problems on the wing and flaps without adversely affecting static turning performance over the desired range of flap deflection and thrust condition.

Shivers, J. P.↗

NASA NTRS1975

Fluctuating pressures on aircraft wing and flap surfaces associated with powered-lift systems

The present work presents results from two research studies that provide information on the fluctuating pressures generated by the use of powered-lift systems in STOL aircraft. Data are given for several chordwise and spanwise locations on large-scale models of an externally blown flap (EBF) configuration and an upper surface blown flap (USB) configuration in which actual jet engines were used. Pressure levels were high enough to indicate that special design effort will be required to avoid acoustic fatigue failures of wing and flap sturctures. The observation that pressure levels did not decrease very much with increased distance from the engine exhaust center line suggests that a STOL aircraft fuselage, which is in relatively close proximity to the engines for aerodynamic reasons, will be subjected to unusually high external overall fluctuating pressure levels (OAFPLs) that may cause difficulty in control of the cabin noise level.

Mixson, J. S.↗