Search NASA⌕ Search

SEARCH · Search NASA

Results for “hardness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

A Study of Microstructure Evolution During Creep of 9Cr-1Mo Steel Using Ultrasonic and Hardness Measurements

In this work, microstructural changes during creep of 9Cr-1Mo steel were characterized using ultrasonic and hardness measurements. The creep testing of this steel was firstly performed at 873 K under the initial stresses of 160 and 175 MPa, respectively. Then, eight specimens under each stress level were prepared by the interrupted tests to simulate various creep states. Subsequently, two parameters of ultrasonic attenuation and velocity were introduced by the ultrasonic testing. Experiment results showed that regardless of the stresses, the ultrasonic attenuation experiences a peak at about 20% of the creep rupture time and a minimum value at about 50%, showing a strong correlation between ultrasonic attenuation and the creep life fraction. In addition to a slight increase during the primary creep, the ultrasonic velocity exhibits a significant change during the tertiary creep. Based on the analysis of microstructure changes, it indicated that the ultrasonic attenuation is significantly sensitive to the dynamic changes of the dislocation. In contrast, the velocity is mainly related to the evolution of precipitates. The Vickers hardness decreases monotonously during the creep process and presents a linear relation with the inverse of average diameter of M{sub 23}C{sub 6} carbides during the secondary and tertiary creep. Accordingly, it suggested that the present ultrasonic and hardness measurements provided a convenient tool to evaluate the microstructure evolution during creep degradation of heat-resistant steels.

36 MATERIALS SCIENCE↗

Extremely hard amorphous-crystalline hybrid steel surface produced by deformation induced cementite amorphization

Amorphous and nanograined (NG) steels are two categories of strong steels. However, over the past decade, their application has been hindered by their limited plasticity, the addition of expensive alloying elements, and processing challenges associated with producing bulk materials. Here in this work, we report that the surface of a carburized Fe-Mn-Si martensitic steel with extremely low elemental alloying additions can be economically fabricated into an amorphous-nanocrystalline hybrid structure. Atom probe tomography and nanobeam diffraction of a hard turned steel surface together with molecular dynamics (MD) simulations reveal that the original cementite surface structure experiences a size-dependent amorphization and phase transformation during heavy plastic deformation. MD simulations further show that the martensite-cementite interface serves as a nucleation site for cementite amorphization, and that cementite can become disordered if further strained when the cementite particles are relatively small. These graded structures exhibit a surface hardness of ~16.2 GPa, which exceeds the value of ~8.8 GPa for the original nanocrystalline martensitic steel and most nanocrystalline steels reported before. Finally, this practical and cost-efficient approach for producing a hard surface with retained bulk ductility and toughness can provide expanded opportunities for producing an amorphous-crystalline hybrid structure in steels and other alloy systems.

36 MATERIALS SCIENCE↗

Rapid discovery of high hardness multi-principal-element alloys using a generative adversarial network model

Multi-principal element alloys (MPEAs) continue to gain research prominence due to their promising high-temperature microstructural and mechanical properties. Recently, machine learning (ML) and materials informatics have been used extensively for screening MPEAs, however, most of these efforts were focused on constructing classification and regression models for predicting phase stability and mechanical properties of known compositions. These approaches may accelerate the screening process but optimizing new compositions with desirable properties within a practical time frame from an infinitely large design space of MPEA systems remains a grand challenge. To tackle this composition optimization challenge, a generative adversarial network coupled with a neural-network ML model was utilized to design MPEAs by filtering compositions that have high hardness. Even in a high-dimensional space with 18 elements as descriptors, the ML model was able to generate optimized compositions from which one composition was found to have 10% higher hardness (941 HV) than the maximum in the training data (857 HV). Density-functional theory was used to provide thermodynamic and electronic insights to higher hardness of the new MPEA found. The present work can optimize compositions from a wide design space of 18 elements (including W, Ta and Nb) that presents an opportunity to synthesize new compositions for applications ranging from corrosion-resistant alloys to nuclear materials. Here the findings suggest that generative ML can greatly accelerate materials discovery by identifying novel compositions, which can serve as a data-informed tool to guide experiments.

36 MATERIALS SCIENCE↗

Atomic migration of carbon in hard turned layers of carburized bearing steel

In grain finement and non-equilibrium there is carbon segregation within grain boundaries alters the mechanical performance of hard turning layers in carburized bearing steel. Moreover, an atom probe tomography (APT) study on the nanostructured hard turning layers reveals carbon migration to grain boundaries as a result of carbide decomposition during severe plastic deformation. In addition, samples exposed to different cutting speeds show that the carbon migration rate increases with the cutting speed. For these two effects lead to an ultrafine carbon network structure resulting in increased hardness and thermal stability in the severely deformed surface layer.

36 MATERIALS SCIENCE↗

Ameliorating the sodium storage performance of hard carbon anode through rational modulation of binder

Hard carbon anodes have emerged as promising candidates for sodium-ion batteries due to their inherent advantages. Nevertheless, the surface imperfections in these materials often culminate in irreversible electrolyte consumption, fostering the development of a heterogeneous and fragile solid electrolyte interface (SEI), thereby compromising the initial Coulombic efficiency (ICE). Here, drawing inspiration from the catalytic potential of C=O (carbonyl) bonds in directing preferential salt reduction, we introduce a novel strategy that leverages the modulation of the binder, a long-term overlooked pivotal components in the electrode process. Specifically, Polymethyl methacrylate (PMMA), abundant in C=O groups, is partially substituted for PVDF, ensuring robust adhesion of the electrode material to the current collector while preserving superior mechanical properties. The accurate combination of two binders with delightful compatibility in the state-of-art electrode process, can promote a uniform formation of the SEI on the hard carbon surface enriched in inorganic components, which can ensure long-term interfacial stability and suppresses excessive solvent decomposition and facilitates Na + transfer at the interface. Consequently, the initial Coulombic efficiency of the hard carbon anode with 70 %PMMA binder achieves 86 %, with prominent cycling stability (88 % capacity retention over 500 cycles) at a high current density of 1.2 A g −1 . When paired with high loading cathodes to assemble the pouch cell, it also demonstrates stable operational scenarios.

25 ENERGY STORAGE↗

Low-compressibility and hard material carbon nitride imide C{sub 2}N{sub 2}(NH): First principles calculations

First principles calculations are performed to investigate the structural, mechanical, and electronic properties of C{sub 2}N{sub 2}(NH). Our calculated lattice parameters are in good agreement with the experimental data and previous theoretical values. Orthorhombic C{sub 2}N{sub 2}(NH) phase is found to be mechanically stable at an ambient pressure. Based on the calculated bulk modulus and shear modulus of polycrystalline aggregate, C{sub 2}N{sub 2}(NH) can be regarded as a potential candidate of ultra-incompressible and hard material. Furthermore, the elastic anisotropy and Debye temperatures are also discussed by investigating the elastic constants and moduli. Density of states and electronic localization function analysis show that the strong C-N covalent bond in CN{sub 4} tetrahedron is the main driving force for the high bulk and shear moduli as well as small Poisson's ratio of C{sub 2}N{sub 2}(NH). -- Graphical abstract: Contours of electronic localization function (ELF) of C{sub 2}N{sub 2}(NH) on the: (0 0 1) plane (a), (1 0 0) plane (b), an ELF of Si{sub 2}N{sub 2}(NH) on the: (0 0 1) plane (c) and (1 0 0) plane (d). Display Omitted Research highlights: The structural, mechanical, and electronic properties of C{sub 2}N{sub 2}(NH) have been studied. C{sub 2}N{sub 2}(NH) is a potential low compressible and hard material. Both C{sub 2}N{sub 2}(NH) and Si{sub 2}N{sub 2}(NH) are found to have insulating feature with large band gaps. The strong covalent C-N bonding in CN{sub 4} tetrahedrons play a key role in the incompressibility and hardness of C{sub 2}N{sub 2}(NH). The chemical bonding in these two solids is a complex mixture of covalent and ionic characters.

36 MATERIALS SCIENCE↗

Prediction of novel hard phases of Si{sub 3}N{sub 4}: First-principles calculations

Exploration of novel hard metastable phases of silicon nitride was performed using a recently developed particle-swarm optimization method within the CALYPSO software package. Three potential hard metastable phases of t-Si{sub 3}N{sub 4}, m-Si{sub 3}N{sub 4}, and o-Si{sub 3}N{sub 4} were predicted. These phases are mechanically and dynamically stable at ambient pressure based on their elastic constants and phonon dispersions. t-Si{sub 3}N{sub 4} and m-Si{sub 3}N{sub 4} exhibit lower energies than γ-Si{sub 3}N{sub 4} at pressures below 2.5 GPa and 2.9 GPa, respectively, which promise that the formers could be obtained by quenching from γ-Si{sub 3}N{sub 4}. o-Si{sub 3}N{sub 4} is a better high-pressure metastable phase than CaTi{sub 2}O{sub 4}-type Si{sub 3}N{sub 4} proposed by Tatsumi et al. and it can come from the transition of γ-Si{sub 3}N{sub 4} under 198 GPa. The theoretical band gaps of t-Si{sub 3}N{sub 4}, m-Si{sub 3}N{sub 4}, and o-Si{sub 3}N{sub 4} at ambient pressure were 3.15 eV, 3.90 eV, and 3.36 eV, respectively. At ambient pressure, the Vickers hardness values of t-Si{sub 3}N{sub 4} (32.6 GPa), m-Si{sub 3}N{sub 4} (31.5 GPa), and o-Si{sub 3}N{sub 4} (36.1 GPa) are comparable to β-Si{sub 3}N{sub 4} and γ-Si{sub 3}N{sub 4}. With the pressure increasing, t-Si{sub 3}N{sub 4}, m-Si{sub 3}N{sub 4}, and o-Si{sub 3}N{sub 4} will change from the brittle to ductile state at about 15.7 GPa, 7.3 GPa and 28.9 GPa, respectively. - Graphical abstract: This figure shows the crystal structures of three Si{sub 3}N{sub 4} predicted in this manuscript, and left to right: t-Si{sub 3}N{sub 4}, m-Si{sub 3}N{sub 4} and o-Si{sub 3}N{sub 4}. - Highlights: • We explored three metastable phases of Si{sub 3}N{sub 4} — t-Si{sub 3}N{sub 4}, m-Si{sub 3}N{sub 4}, and o-Si{sub 3}N{sub 4}. • The enthalpies of t and m- are much lower than that of γ at ambient pressure. • ois one further high pressure phase than γ. • o-Si{sub 3}N{sub 4} is the most hardest phase in Si{sub 3}N4 system. • Increasing pressure will change them from brittle to ductile state.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructural and hardness investigations on a dissimilar metal weld between low alloy steel and Alloy 82 weld metal

The investigation on microstructure and hardness at the fusion boundary (FB) region of a dissimilar metal weld (DMW) between low alloy steel (LAS) A508-III and Alloy 82 weld metal (WM) was carried out. The results indicated that there were two kinds of FBs, martensite FB and sharp FB, with obvious different microstructures, alternately distributed in the same FB. The martensite FB region had a gradual change of elemental concentration across FB, columnar WM grains with high length/width ratios, a thick martensite layer and a wide heat affected zone (HAZ) with large prior austenite grains. By comparison, the sharp FB region had a relatively sharp change of elemental concentration across the FB, WM grains with low length/width ratios and a narrow HAZ with smaller prior austenite grains. The martensite possessed a K-S orientation relationship with WM grains, while no orientation relationship was found between the HAZ grains and WM grains at the sharp FB. Compared with sharp FB there were much more Σ3 boundaries in the HAZ beside martensite FB. The hardness maximum of the martensite FB was much higher than that of the sharp FB, which was attributed to the martensite layer at the martensite FB. - Highlights: •Martensite and sharp FBs with different microstructures were found in the same FB. •There were high length/width-ratio WM grains and a wide HAZ beside martensite FB. •There were low length/width-ratio WM grains and a narrow HAZ beside sharp FB. •Compared with sharp FB, there were much more Σ3 boundaries in HAZ of martensite FB. •Hardness maximium of martensite FB was much higher than that of sharp FB.

36 MATERIALS SCIENCE↗

Radiation hardness characterization of LKH-5 scintillating glass

Radiation hardness is an important property to examine in scintillators to help determine their expected lifetime in application cases where significant radiation dose is expected. Industrial imaging systems using 9 MV linear accelerators for x-ray radiography are one such application where significant radiation doses are expected to the scintillators used. Cadmium tungstate scintillators (CWO) and Thallium doped Cesium Iodide scintillators (CsI(Tl)) are used in some high energy cargo x-ray radiography systems. However, CWO has a high manufacturing cost for adequately uniform crystals and CsI(Tl) does not have sufficient radiation hardness. LKH-5 glass is being investigated as a potential low cost replacement for CWO and CsI(Tl). In this experiment 36 samples of a terbium doped silicate glass called LKH-5 were irradiated at doses up to 5 MRad using a 9 MV linear accelerator, and the change in their transmission properties was observed. Additionally, the glass was discovered to be a radiation hard glass due to the relatively small change in the transmission of the glass: less than 3% per cm at its emission peak of 550 nm and 5 MRad. This is similar to CWO which has a reported reduction in transmitted light of 2% per cm at 5 MRad and the emission peak of 475 nm and better than CsI(Tl) which is reported to have a reduction in transmitted light of 5% per cm at the emission peak of 550 nm and 4.2 MRad dose. Furthermore, an annealing procedure is described that returned the transmission of the glass to pre-irradiation values.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Microstructural Assessment of Molybdenum Disulfide Coatings Using Nanoindentation Hardness

MoS 2 coatings are used extensively in aerospace and defense applications due to their ultralow friction and high wear resistance. Burnished and resin-bonded MoS 2 coatings are commonly used in these applications due to simplicity in deposition and history of use, despite issues with consistency in coating properties and performance. Physical vapor deposition (PVD) of MoS 2 thin films has emerged as a process alternative in the past 50 years, promising far greater control over film structure and composition but at a greater cost. Despite PVD’s benefits, hesitance to adoption persists in high-consequence applications, not only due to increased costs but variability in resulting coating properties. These variations in properties and subsequent performance are in part due to the complexity of the PVD process and the sensitive interplay between coating process-structure-property relationships. This work aims to demystify the remaining uncertainties of the process-structure-property relationships in PVD MoS 2 . The microstructure and mechanical and tribological properties of 61 different PVD pure MoS 2 coatings are examined herein. Emphasis has been placed on developing performance-based (i.e., hardness, modulus) metrics that can assess microstructural changes (density, orientation, and crystallinity) and be utilized to accelerate process development and coating optimization. Relationships established within suggest that nanoindentation hardness can be used to infer coating performance (i.e., wear rate) and properties (i.e., density, crystalline texture, and stoichiometry). Furthermore, this work demonstrates that PVD MoS 2 coatings close to the theoretical density of MoS 2 consistently have the best tribological performance and can be reliably identified by their hardness.

MoS2↗

Host Galaxy Properties of BAT Hard X-ray Selected AGN

Surveys of AGN taken in the optical, UV, and soft X-rays miss an important population of obscured AGN only visible in the hard X-rays and mid-IR wavelengths. The SWIFT BAT survey in the hard X-ray range (14-195 keV) has provided a uniquely unbiased sample of 246 AGN unaffected by galactic or circumnuclear absorption [1]. Most of the sources in the survey are bright, Seyfert like AGN's with median redshift of 0.03. Of the AGN, 43% are obscured, type II AGN. We obtained 17 nights of imaging of 90 host galaxies of these AGN in 2008 at the Kitt Peak 2.1 m telescope in the SDSS ugriz filters. For the broad line sources we subtracted the AGN contribution using GALFIT. By comparing our sample of AGN to inactive galaxies in the SDSS, we find that AGN are found in the most massive galaxies and are bluer in color than inactive galaxies of comparable stellar mass. We also find a correlation between the point source optical light and hard X-ray luminosity.

79 ASTRONOMY AND ASTROPHYSICS↗

Bright, low debris, ultrashort hard x-ray table top source using carbon nanotubes

We demonstrate that carbon nanotube coated surfaces produce two orders of magnitude brighter hard x-ray emission, in laser produced plasmas, than planar surfaces. It is accompanied by three orders of magnitude reduction in ion debris which is also low Z and nontoxic. The increased emission is a direct consequence of the enhancement in local fields and is via the simple and well known 'lightning rod' effect. We propose that this carbon nanotube hard x-ray source is a simple, inexpensive, and high repetition rate hard x-ray point source for a variety of applications in imaging, lithography, microscopy, and material processing.

07 ISOTOPE AND RADIATION SOURCES↗

Development of an Adaptive Optical System for Sub-10-nm Focusing of Synchrotron Radiation Hard X-rays

In the hard x-ray region, to obtain the theoretical resolution or diffraction-limited focusing size in an imaging optical system, both ultraprecise optics and highly accurate alignment are necessary. An adaptive optical system is used for the compensation of aberrations in various optical systems, such as optical microscopes and space telescopes. In situ wavefront control of hard x-rays is also effective for realizing ideal performance. The aim of this paper is to develop an adaptive optical system for sub-10-nm hard x-ray focusing. The adaptive optical system performs the wavefront measurement using a phase retrieval algorithm and wavefront control using grazing-incidence deformable mirrors. Several results of experiments using the developed system are reported.

43 PARTICLE ACCELERATORS↗

Compressibility and hardness of Co-based bulk metallic glass: A combined experimental and density functional theory study

An incompressible Co{sub 54}Ta{sub 11}B{sub 35} bulk metallic glass (BMG) was investigated using in situ high-pressure synchrotron diffraction and nanoindendation. The elastic constants were deduced from the experiments based on the isotropic model. The Vickers hardness was measured to be 17.1 GPa. The elastic moduli and hardness are the highest values known in BMGs. The theoretically calculated elastic properties by density-functional study were well consistent with experimental measurements. The analysis of charge density and bonding character indicates the covalent character of Co-B and B-B bonds, underlying the unusually high elastic modulus and hardness in this material.

36 MATERIALS SCIENCE↗

Sensitivity study of ignition capsule implosion performance on the hard x-ray spectral distribution of hohlraum

The paper investigates theoretically the sensitivities of ignition capsule implosion performance on the hard x-ray spectral distribution of hohlraum. In the simulation, the hohlraum radiation is represented by a Planckian spectrum for the main drive plus a gaussian bump centered at energy E{sub c} for preheating x-rays. Simulation results show that with the increasing of center energy E{sub c}, the Atwood number at the fuel-ablator interface increases rapidly due to the preheating and expanding of the inner undoped CH layer. The growing of Atwood number indicates the hydrodynamic instability (HI) growth and mixing at this interface. On the other hand, the increasing of E{sub c} results in a large density gradient scale length of ablation front and stabilizes the HI growth at ablation front. The changes of the hard x-ray spectrum have significant influences on other important implosion parameters including the ablator mass remaining, shock timing, implosion velocity, and yield as well. High-precision results on the hard x-ray spectral distribution of hohlraum are thus critical for optimizing the ignition capsule design to limit the HI growth.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Islands stretch test for measuring the interfacial fracture energy between a hard film and a soft substrate

We present a technique for measuring the interfacial fracture energy, {Gamma}{sub i}, between a hard thin film and a soft substrate. A periodic array of hard thin islands is fabricated on a soft substrate, which is then subjected to uniaxial tension under an optical microscope. When the applied strain reaches a critical value, delamination between the islands and the substrate starts from the edge of the islands. As the strain is increased, the interfacial cracks grow in a stable fashion. At a given applied strain, the width of the delaminated region is a unique function of the interfacial fracture energy. We have calculated the energy release rate driving the delamination as a function of delamination width, island size, island thickness, and applied strain. For a given materials system, this relationship allows determination of the interfacial fracture energy from a measurement of the delamination width. The technique is demonstrated by measuring the interfacial fracture energy of plasma-enhanced chemical vapor deposition SiN{sub x} islands on a polyimide substrate. We anticipate that this technique will find application in the flexible electronics industry where hard islands on soft substrates are a common architecture to protect active devices from fracture.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effects of sequential tungsten and helium ion implantation on nano-indentation hardness of tungsten

To simulate neutron and helium damage in a fusion reactor first wall sequential self-ion implantation up to 13 dpa followed by helium-ion implantation up to 3000 appm was performed to produce damaged layers of {approx}2 {mu}m depth in pure tungsten. The hardness of these layers was measured using nanoindentation and was studied using transmission electron microscopy. Substantial hardness increases were seen in helium implanted regions, with smaller hardness increases in regions which had already been self-ion implanted, thus, containing pre-existing dislocation loops. This suggests that, for the same helium content, helium trapped in distributed vacancies gives stronger hardening than helium trapped in vacancies condensed into dislocation loops.

36 MATERIALS SCIENCE↗

Study of runaway electrons using dosimetry of hard x-ray radiations in Damavand tokamak

In this work several studies have been conducted on hard x-ray emissions of Damavand tokamak based on radiation dosimetry using the Thermoluminescence method. The goal was to understand interactions of runaway electrons with plasma particles, vessel wall, and plasma facing components. Total of 354 GR-200 (LiF:Mg,Cu,P) thermoluminescence dosimeter (TLD) crystals have been placed on 118 points – three TLDs per point – to map hard x-ray radiation doses on the exterior of the vacuum vessel. Results show two distinctive levels of x-ray radiations doses on the exterior of the vessel. The low-dose area on which measured dose is about 0.5 mSv/shot. In the low-dose area there is no particular component inside the vessel. On the contrary, on high-dose area of the vessel, x-ray radiations dose exceeds 30 mSv/shot. The high-dose area coincides with the position of limiters, magnetic probe ducts, and vacuum vessel intersections. Among the high-dose areas, the highest level of dose is measured in the position of the limiter, which could be due to its direct contact with the plasma column and with runaway electrons. Direct collisions of runaway electrons with the vessel wall and plasma facing components make a major contribution for production of hard x-ray photons in Damavand tokamak.

61 RADIATION PROTECTION AND DOSIMETRY↗