Search NASA⌕ Search

SEARCH · Search NASA

Results for “interface stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Achieving Electrode Smoothing by Controlling the Nucleation Phase of Metal Deposition Through Polymer‐Substrate Binding

Polymer additives [like polyethylene oxide (PEO)] are widely used for smooth electrode deposition in aqueous zinc and many other battery systems. However, the precise mechanism by which they regulate morphology and suppress dendrite formation remains unclear. In this study, the knowledge gap is addressed by using in situ electrochemical atomic force microscopy to directly observe the interfacial evolution during Zn electrodeposition and polymer adsorption on Cu substrates in the presence of varying concentrations of ZnSO 4 and PEO. Contrary to previous literature assumptions, which emphasize the binding to the growing Zn crystal surfaces or Zn 2+ ions, the results demonstrate that PEO smooths Zn films by promoting nucleation of (002)-oriented Zn platelets through interactions with the Cu substrate. Density functional theory simulations support this finding by showing that PEO adsorption on Cu modifies the interfacial energy of Zn/Cu/electrolyte interfaces, favoring the stabilization of Zn (002) on the Cu substrate, as well as confines Zn electrodeposition to a narrow near-surface region. In conclusion, these findings elucidate a novel design principle for electrode smoothing, emphasizing the importance of substrate selection paired with polymer additives that exhibit an attractive interaction with the substrate but minimal interaction with growing crystals, offering a mechanistic perspective for improved battery performance.

Electrodeposition↗

Ghost states and surface structures of the charge density wave kagome metal ScV 6 Sn 6

In this work, we investigate the high-temperature phase of the kagome metal ScV 6 Sn 6 using scanning tunneling microscopy/spectroscopy (STM/S) and density functional theory calculations. STM topographic images of the cleaved sample reveal two distinct surface terminations: flat islands with Sn termination and trenches terminated by kagome layers with Sn as the outermost atomic layer. STS measurements on the Sn-terminated and kagome-terminated surfaces show significant differences, in particular the presence of large density of states near the Fermi level in the former case. Our first-principles calculations reveal that the charge density on the kagome-terminated surface gives rise to “ghost states” which show intensity away from surface atoms, arising due to hybridization of orbitals above the surface. These states can obscure the intrinsic properties of the surface, potentially leading to misattribution of the surface termination. This underscores the need for careful interpretation in STM studies, especially when discerning surface states of localized states. Understanding the surface structure of this versatile quantum material provides essential information for interpreting surface-sensitive experiments, tailoring material properties, engineering interfaces, and controlling stability and reactivity. This knowledge paves the way for further exploration and potential applications of kagome lattice materials in various fields, including quantum computing, topological physics, and advanced electronic devices.

36 MATERIALS SCIENCE↗

Martensitic transformations in Ti-6Al-4V (ELI) alloy manufactured by 3D Printing

Highlights: • Two metastable martensitic phases, namely α′′ and α′ may be formed in Ti-6Al-4V during 3D manufacturing process. In the present investigation, Ti-6Al-4V ELI samples were manufactured by the powder-bed fusion (PBF) process using the laser sintering (LS) technology. Microstructure, chemical and phase constitution, and mechanical properties were studied by means of the transmission electron microscopy, atom probe tomography, X-ray diffraction, nanoindentation and mechanical testing. It was found that the structure of LS samples consisted of two different variants of metastable phases, namely the hexagonal α′ martensitic phase and small amounts of the orthorhombic α″ martensitic phase. The martensitic α′-phase was formed because of the high cooling rates of the LS method. The {10 1-bar 2} 1-bar 011 hexagonal martensite tensile twins were observed in the microstructure of the as-build alloy. Small areas with inner twinning martensitic plates, which are typical for the metastable orthorhombic martensitic phase in titanium alloys, were identified by the transmission electron microscopy. Atom probe tomography (APT) confirmed localization of β-stabilizing elements at interfaces, presumably at the twin or lamella boundaries. The structure and origin of the martensitic phases in 3D printed Ti-6Al-4V alloys are discussed with respect to in-situ heat treatment during manufacturing.

36 MATERIALS SCIENCE↗

Li-Metal Anode in Dilute Electrolyte LiFSI/TMP: Electrochemical Stability Using Ab Initio Molecular Dynamics

Ab initio molecular dynamics simulations were performed for Li + conducting electrolytes based on trimethyl phosphates (TMP) and lithium bis(fluorosulfonyl)imide (Li + FSI – ) salt in contact with a Li-metal electrode. We focused on the transient-state behavior at the electrolyte, interfacial electrolyte–Li-metal electrode, and lithium reference electrode–electrolyte–Li-metal electrode to study dynamics and activation energy barriers of the Li + ion, electrochemical and thermal stability of the interface electrode-electrolyte, and potential behavior of the Li-metal electrode, respectively. Our results show that in the most stable state, Li + ions are tetrahedrally coordinated to three TMPs and one FSI – . The inner solvation shell of a Li-ion is composed of three TMP and one FSI – in one contact ion-pair and four TMPs in a solvent-separated ion-pair. On the other hand, Li-ions transport through electrolyte cages takes place when they are coordinated with three or less molecules that could be a combination of TMPs and FSI – . The decomposition pathway of the LiFSI salt when in direct contact with the Li-metal anode starts with defluorination of FSI – , rapidly losing F– to the lithium surface, forming LiF species. The remaining FSO 2 NSO 2 –2 with the addition of 2e – from the Li-metal decomposes into SO 2 –2 and NFSO 2 –2 . SO 2 –2 deposits on the Li-surface and decomposes into Li 2 O and Li 2 S. The remaining NFSO 2 –2 defluorinates, losing F – ion to the lithium surface, resulting in LiF and the remaining NSO 2 –1 deposits on the lithium surface and decomposes in the following picoseconds, forming several binary compounds such as Li 3 N, Li 2 S and Li 2 O. In contrast, when the salt is solvated by the TMP molecules, avoiding a direct contact with the Li metal electrode, only one defluorination occurs, decomposing the FSI – into FSO 2 NSO 2 –2 and a F – . The two anions remain stable as they are solvated by the TMP molecules. Furthermore, we also analyzed the open circuit potential energy (OCPE) of the Li-metal electrode during the SEI formation. OCPE is calculated from the average local potential profile difference within the Li-metal electrode and a pristine Li-crystal reference electrode (LRE). When no SEI is formed, the Li-metal electrode has an average OCPE of +0.36 eV vs LRE. Due to the formation of a SEI, the Li-metal electrode has an average OCPE between -0.07 and -0.21 eV vs LRE. The OCPE of the Li-metal electrode decreases by ~0.42 eV when a SEI is formed.

25 ENERGY STORAGE↗

Two-Dimensional Crystallization of Poly( N -isopropylacrylamide)-Capped Gold Nanoparticles

Surface-sensitive X-ray reflectivity and grazing incidence small-angle X-ray scattering reveal the structure of polymer-capped-gold nanoparticles (AuNPs that are grafted with poly(N-isopropylacrylamide); PNIPAM–AuNPs) as they self-assemble and crystallize at the aqueous suspension/vapor interface. Citrate-stabilized AuNPs (5 and 10 nm in nominal diameter) are ligand-exchanged by 6 kDa PNIPAM-thiol to form corona brushes around the AuNPs that are highly stable and dispersed in aqueous suspensions. Surprisingly, no clear evidence of thermosensitive effect on surface enrichment or self-assembly of the PNIPAM–AuNPs is observed in the 10–35 °C temperature range. However, addition of simple salts (in this case, NaCl) to the suspension induces migration of the PNIPAM–AuNPs to the aqueous surface, and above a threshold salt concentration, two-dimensional crystals are formed. In conclusion, the 10 nm PNIPAM–AuNPs form a highly ordered single layer with in-plane triangular structure, whereas the 5 nm capped NPs form short-range triangular structure that gradually becomes denser as salt concentration increases.

36 MATERIALS SCIENCE↗

Role of Cations in the Cation-Driven Assembly Process and their Effect on the Charge Storage Properties of Bilayered Vanadium Oxide and Reduced Graphene Oxide Heterostructures in Alkali Ion Systems

Exfoliated δ-Li x V 2 O 5 ·nH 2 O (ex-LVO) and reduced graphene oxide (rGO) heterostructures were constructed using different assembling cations (i.e., Li⁺, Na⁺, and K⁺ ions). The ex-LVO and rGO nanoflakes were stacked together using a concentrated chloride solution of each assembling cation and vacuum annealed at 200 °C to form three distinct two-dimensional (2D) layered architectures. X-ray diffraction and thermogravimetric analysis confirmed that the assembling ions can control the interlayer spacing of the bilayered vanadium oxide (BVO) phase as well as impact the crystallographic water content, which in turn affects the electrochemical performance. Scanning electron microscopy, scanning transmission electron microscopy (STEM), electron energy-loss spectroscopy (EELS), and X-ray photoelectron spectroscopy confirmed that a 2D heterointerface formed between LVO and rGO and that the cations used to assemble the heterostructure are trapped in the interlayer BVO region. High-resolution STEM imaging also showed the rGO dispersion throughout the LVO layers. Moreover, STEM-EELS identified a V 2 O 3 phase that forms along the rGO interface and can stabilize the materials during cycling. A charge storage mechanism analysis, combined with the galvanostatic intermittent titration technique, found that increased interlayer spacings of the BVO phase and using the assembling cations to define intercalation sites for identical charge-carrying ions lead to improved ion diffusion and increased capacities during cycling. Therefore, the Li⁺ and Na⁺ ion assembled heterostructures showed improved charge-carrying ion diffusion and charge storage capacities in each of their respective charge storage systems (i.e., Li-ion and Na-ion half-cells). In total, the cation used for heterostructure assembly can modify the final material structure and tailor the ion diffusion and charge storage capacity to tune its properties for the desired electrochemical system using a variety of 2D materials.

25 ENERGY STORAGE↗

Surface Chemistry, Passivation, and Electrode Performance in Core–Shell Architectures of LiCoO 2 Nanoplates

Core–shell structures offer opportunities to overcome challenges to the durability of Li-ion batteries with high energy density due to instability at the cathode/electrolyte interface. Achieving complete stability requires fundamental understanding of the role of the shell in providing passivation without compromising carrier transport, by tuning surface chemistry and structural features in a highly conformal barrier layer. Here, individual LiCoO 2 nanoplates were employed as the core, and passivating shells were grown at a tailored thickness and composition, through different Al loadings and annealing temperatures. Depending on the annealing conditions, the sub-5 nm shells were shown to vary from amorphous aluminum oxide layers to LiAl x Co 1–x O 2 gradients, resulting in an Al-rich outer layer on a Co-rich core. This control revealed the differing balance between effective minimization of redox-active Co 3+ at the surface and transport properties of the two types of shell. Based on correlations with electrode performance, the requirements in thickness of the layers were proposed to critically depend on their chemical composition, with epitaxial shells based on surface substitution being favored. As a result, the outcomes of the study simultaneously advance the ability to assemble complex oxides into heterostructures and refine the rules of design for tunable passivation through a barrier layer, so as to maximize electrode properties in practical batteries.

25 ENERGY STORAGE↗

Eliminating chemo-mechanical degradation of lithium solid-state battery cathodes during >4.5 V cycling using amorphous Nb2O5 coatings

Abstract Lithium solid-state batteries offer improved safety and energy density. However, the limited stability of solid electrolytes (SEs), as well as irreversible structural and chemical changes in the cathode active material, can result in inferior electrochemical performance, particularly during high-voltage cycling (>4.3 V vs Li/Li + ). Therefore, new materials and strategies are needed to stabilize the cathode/SE interface and preserve the cathode material structure during high-voltage cycling. Here, we introduce a thin (~5 nm) conformal coating of amorphous Nb 2 O 5 on single-crystal LiNi 0.5 Mn 0.3 Co 0.2 O 2 cathode particles using rotary-bed atomic layer deposition (ALD). Full cells with Li 4 Ti 5 O 12 anodes and Nb 2 O 5 -coated cathodes demonstrate a higher initial Coulombic efficiency of 91.6% ± 0.5% compared to 82.2% ± 0.3% for the uncoated samples, along with improved rate capability (10x higher accessible capacity at 2C rate) and remarkable capacity retention during extended cycling (99.4% after 500 cycles at 4.7 V vs Li/Li + ). These improvements are associated with reduced cell polarization and interfacial impedance for the coated samples. Post-cycling electron microscopy analysis reveals that the Nb 2 O 5 coating remains intact and prevents the formation of spinel and rock-salt phases, which eliminates intra-particle cracking of the single-crystal cathode material. These findings demonstrate a potential pathway towards stable and high-performance solid-state batteries during high-voltage operation.

Science & Technology - Other Topics↗

DFT modelling of explicit solid–solid interfaces in batteries: methods and challenges

Density Functional Theory (DFT) calculations of electrode material properties in high energy density storage devices like lithium batteries have been standard practice for decades. By contrast, DFT modelling of explicit interfaces in batteries arguably lacks universally adopted methodology and needs further conceptual development. In this paper, we focus on solid–solid interfaces, which are ubiquitous not just in all-solid state batteries; liquid-electrolyte-based batteries often rely on thin, solid passivating films on electrode surfaces to function. We use metal anode calculations to illustrate that explicit interface models are critical for elucidating contact potentials, electric fields at interfaces, and kinetic stability with respect to parasitic reactions. The examples emphasize three key challenges: (1) the “dirty” nature of most battery electrode surfaces; (2) voltage calibration and control; and (3) the fact that interfacial structures are governed by kinetics, not thermodynamics. To meet these challenges, developing new computational techniques and importing insights from other electrochemical disciplines will be beneficial.

25 ENERGY STORAGE↗

Subcutaneous oxidation of In{sub 0.53}Ga{sub 0.47}As(100) through ultra-thin atomic layer deposited Al{sub 2}O{sub 3}

Stability of oxide/semiconductor interfaces during device fabrication is critically important, particularly for adoption of new semiconductor channel materials, such as III-V compounds. Unintentional oxidation of an underlying In{sub 0.53}Ga{sub 0.47}As(100) surface through atomic layer deposited (ALD) Al{sub 2}O{sub 3} layers of varying thickness is investigated. Oxygen annealing of 1 ∼ 2 nm thickness Al{sub 2}O{sub 3} layers at 300 °C or higher and large-dose water vapor exposure during the ALD-Al{sub 2}O{sub 3} process at 300 °C produces InGaAs surface oxidation. This subcutaneous oxidation of InGaAs increases the Al{sub 2}O{sub 3}/InGaAs interface defect density as observed in suppressed band-edge photoluminescence and in capacitance-voltage analysis, possibly by creating As dangling bonds at the InGaAs surface.

36 MATERIALS SCIENCE↗

The mechanics of nucleation and growth and the surface tensions of active matter

Homogeneous nucleation, a textbook transition path for phase transitions, is typically understood on thermodynamic grounds through the prism of classical nucleation theory. However, recent studies have suggested the applicability of classical nucleation theory to systems far from equilibrium. Here, in this article, we formulate a purely mechanical perspective of homogeneous nucleation and growth, elucidating the criteria for the properties of a critical nucleus without appealing to equilibrium notions. Applying this theory to active fluids undergoing motility-induced phase separation, we find that nucleation proceeds in a qualitatively similar fashion to equilibrium systems, with concepts such as the Gibbs–Thomson effect and nucleation barriers remaining valid. We further demonstrate that the recovery of such concepts allows us to extend classical theories of nucleation rates and coarsening dynamics to active systems upon using the mechanically derived definitions of the nucleation barrier and surface tensions. Three distinct surface tensions—the mechanical, capillary, and Ostwald tensions—play a central role in our theory. While these three surface tensions are identical in equilibrium, our work highlights the distinctive role of each tension in the stability of active interfaces and the nucleation and growth of motility-induced phases.

Capillary waves↗

OECD MCCI Project: Category 2 Coolability Engineering Enhancement Tests (Rev. 1, Final Report)

Ex-vessel debris coolability is an important light water reactor (LWR) safety issue. For existing plants, resolution of this issue will confirm the technical basis for severe accident management guidelines (SAMGs). For new reactors, understanding this issue will help confirm the effectiveness of the design and implementation of new accident mitigation features and severe accident management design alternatives (SAMDAs). The first OECD-MCCI program conducted reactor material experiments focused on achieving the following technical objectives: i) provide confirmatory evidence and data for various cooling mechanisms through separate effect tests for severe accident model development, and ii) provide long-term 2-D coreconcrete interaction data for code assessment and improvement. Specifications for the Water-Cooled Basemat (WCB-1) integral effect test are provided. The objective was to provide prototypic data on the transient evolution and stabilization of a core melt in a generic water-cooled core catcher design for advanced plant applications. The experiment approach was to incorporate a water-cooled basemat into the coreconcrete interaction test apparatus used for the CCI tests. The basemat was composed of five parallel water channels that were instrumented to provide both local and global data on the heat transfer performance. The basemat was covered with a layer of sacrificial concrete that would be ablated by the overlying melt at the start of the experiment. Eventually, the melt would approach, and then be thermally stabilized at, the interface of the water-cooled basemat. Due to the longer timeframe associated with this type of test, it was necessary to Direct Electrically Heat (DEH) the melt to provide sufficient time for the melt to come to thermal equilibrium.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Design of Next-Gen Cathode Materials With Both Cation and Anion Redox

Among all candidates of positive electrode materials for lithium ion batteries, the lithium rich layered oxides have gained growing research interests in recent years. Their energy density can reach closely to 700-900Wh/g (at materials level), making them the positive electrode materials with highest energy density among all known intercalation compounds for cathode materials. Combining both first principles computation, advanced electron and X-ray based imaging, we demonstrated that in the Li-rich materials oxygen vacancies are present and assist the transition metal ion migration through a facile mechanism. This means it is critically important to control the oxygen activities in these compounds for high voltage operations. In addition, the NiMn spinel oxides show little oxygen activities and under optimized synthesis condition the electrolyte/electrode interface showed superior stability. Combining the strengths of materials synthesis and the advanced characterization, I will discuss in details the strategies for stabilizing the anion redox for higher voltage electrode materials for lithium ion batteries.

Meng, Ying Shirley↗

Integrated Multiscale Model for Design of Robust 3D Solid-state Lithium Batteries

In FY23, we successfully established the multiscale modeling framework for probing the effects of materials microstructure on cell performance of 3D solid-state batteries. The framework covers physicochemical processes co-evolving at the atomistic and microstructure scales. Our simulations revealed the mechanism of initial interfacial degradation, formation of secondary phases, and the structure-property relationship for ion transport and mechanical stability at the interface. In addition, we also established the microstructure-performance relationships by performing sensitivity tests of various microstructure features and extracting their impact on cell performance during charge-discharge cycles. We have successfully applied our multiscale, multiphysics modeling capability to common electrode and electrolyte materials that are of interests to VTO and the experimental teams within the US-Germany collaboration. The insights we obtained from these simulations provide valuable design principles to optimize materials properties for advanced 3D solid-state batteries.

25 ENERGY STORAGE↗

A Review on Solid State Batteries: Life Cycle Perspectives

This report briefly reviews the characteristics of solid-state batteries (SSBs) and the life-cycle analysis (LCA) studies that have been completed for SSBs. Compared with conventional lithium-ion batteries (LIBs), SSBs offer improved safety and potentially higher energy density — both enabled by replacing liquid electrolytes with solid electrolytes and using lithium metal anodes. Several challenges impede the commercialization of SSBs, primarily related to the stability of the interface between the solid electrolyte and the electrodes. Several options are under consideration for SSB electrolyte and cathode chemistries. As a result, the production processes for these components and the corresponding battery packs are still under development and can differ significantly from those used for conventional LIB pack production. A robust comparison of SSBs with LIBs through LCA is important to analyze the environmental benefits and challenges associated with this alternative battery system. While the literature provides only a few LCA studies focused on SSBs, with significant uncertainty in their life-cycle inventories (LCIs), those studies collectively suggest that solid electrolyte manufacturing is the major environmental hotspot, followed by cathode and anode production.

25 ENERGY STORAGE↗

Parallel-Processed Multi-junction Perovskite Solar Cells (Final Technical Report)

This report consolidates the findings from this Department of Energy supported project, which aimed to advance the manufacturing of high-efficiency perovskite photovoltaics. To facilitate the processing of tandem devices, and perovskite single-junction and multi-junction devices more generally, the project team developed a lamination process to integrate the subcells and cells, decoupling the processing from the restrictive requirements of serial manufacturing. The lamination approach enables independent and precise tailoring of interface properties for stability and performance.

14 SOLAR ENERGY↗

Digital temperature sensor performance assessment report

Performance assessment data accumulated during exposure of the digital temperature sensor to simulated shuttle flight type environments are presented. The test parameters were specifically designed to check the sensor for its: (1) ability to resolve temperature relative to the design specifications; (2) ability to maintain accuracy after interchanging the temperature probes with each electronics interface assembly; (3) stability (i.e., satisfactory operation and accuracy during and after exposure to flight environments); and (4) repeatability, or its ability to produce the same output on subsequent exposures to the identical stimulus. Equipment list, test descriptions, data summary, and conclusions are included.

Canniff, J. H.↗