Search NASA⌕ Search

SEARCH · Search NASA

Results for “irradiation testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Specifications of Legacy U(Pu)Zr Metallography Data

The DOE Nuclear Energy Advanced Reactor Technologies (ART) Program has supported the creation of several databases with information describing the safety performance of fast reactors, components, and fuels. This growing collection of legacy experimental data, operating data, and analysis is available online to registered users. Metallography data is one of the most important types of PIE data being collected, organized and stored in several ART Fast Reactor Databases (https://frdb.ne.anl.gov), including the Fuels Irradiation & Physics Database (FIPD), Out-of-Pile Transient Database (OPTD), and TREAT (the Transient Reactor Test Facility) Experimental Relational Database (TREXR). These databases contain three main sets of metallography data. The first set is the metallography data from Experimental Breeder Reactor-II (EBR-II) and Fast Flux Test Facility (FFTF) irradiated fuel pins measured in the Hot Fuel Examination Facility (HFEF); the second set is the metallography data from EBR-II irradiated fuel pins measured in the Alpha-Gamma Hot Cell Facility (AGHCF); the third set is the metallography data from transient tested fuel pins (the transients tests include the out-of-pile tests and TREAT tests) measured in AGHCF. Since both the second and third sets of data were measured in AGHCF, they are governed by the same specification. The metallography data in the databases are digital images scanned from either positive or negative photos. The quality of the images, including their resolution and contrast, relies on the preserved quality of the pictures and the scanning conditions. To analyze the microstructure of a fuel pin, a series of preparatory steps must be undertaken. These include sectioning, epoxy mounting, mechanical grinding and polishing, and often etching. The resulting samples were then transferred to a secondary hot cell, or glovebox (depending the strength of radiation field) for microscopy examination. The specifications provided herein focus on the metallography examinations. The sample grinding, polishing and etching processes are also discussed. The procedures involving sectioning and epoxy mounting are out of the scope of the current specification; details can be found in the corresponding operation manuals. If more data are collected and added to the ART Fast Reactor Databases, this specification will be updated to accommodate the additional data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Determination of Scale Bar for AGHCF Metallography Data

The DOE Nuclear Energy Advanced Reactor Technologies (ART) Fast Reactor Program (FRP) has supported the development of several databases containing information on the safety performance of fast reactors, components, and fuels. This growing collection of legacy experimental data, operating data, and analysis is available online to registered users. Metallography data represents one of the most critical types of post-irradiation examination (PIE) data being collected, organized, and archived in several ART Fast Reactor Databases (https://frdb.ne.anl.gov), including the Metallic Fuels Irradiation & Physics Database (FIPD), Out-of-Pile Transient Database (OPTD), and TREAT (the Transient Reactor Test Facility) Experimental Relational Database (TREXR). These databases contain three principal sets of metallography data. The first set comprises metallography data from Experimental Breeder Reactor-II (EBR-II) and Fast Flux Test Facility (FFTF) irradiated fuel pins examined in the Hot Fuel Examination Facility (HFEF). The second set consists of metallography data from EBR-II irradiated fuel pins examined in the Alpha-Gamma Hot Cell Facility (AGHCF). The third set includes metallography data from transient-tested fuel pins (including both out-of-pile furnace tests and TREAT tests) examined in AGHCF. Since both the second and third sets were generated in AGHCF, they are governed by identical specifications. The metallography data in the databases consist of digital images scanned from either positive or negative photographic films. To analyze the microstructure of a fuel pin, a series of preparatory steps are required, including sectioning, epoxy mounting, mechanical grinding and polishing, and etching. Following sample preparation, specimens are transferred for metallographic examination. The AGHCF and HFEF metallography data were generated using optical microscopes manufactured by Leitz and Bausch and Lomb (B&L). Images were recorded on Polaroid film at preset magnifications. Magnification verification for the Leitz and B&L metallographs was conducted every two months prior to 1989 and at least every six months from 1989 through the conclusion of the IFR program. Magnifications determined from imaging of microslide standards were compared to the instrument settings for magnifications ranging from 50× to 500×. If the magnifications determined from standards deviated from the instrument settings, adjustments were made to the bellows extension until agreement was achieved. The specifications for AGHCF and HFEF legacy metallography data have been established based on available hard-copy and digital records, most of which have been incorporated into the data repositories associated with FIPD, OPTD, and TREXR. Detailed specifications including hard-copy records, digitized records, cutting diagrams and sectioning schemes, high-magnification photographs, photomosaics (composites), information tags, scale bars, and magnification verification procedures can be found in a separate report.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Outdoor performance of a tandem InGaP/Si photovoltaic luminescent solar concentrator

Here, we report the design, fabrication and outdoor characterization of a tandem luminescent solar concentrator/Si multi-junction photovoltaic module. Our tandem LSC/Si device consists of an InGaP LSC functioning as a top cell and a passivated contact Si bottom cell. The LSC comprises of an InGaP microcell array coupled to a polymer waveguide, loaded with CdSe/CdS core-shell quantum dot luminophores. The light trapping efficiency of the LSC waveguide is enhanced by encapsulation with photoluminescence trapping mirrors consisting of dielectric multilayer thin films. We demonstrate the performance of the LSC/Si device through a series of outdoor tests under various irradiance conditions conducted at the National Renewable Energy Laboratory. We report the first outdoor testing data of an LSC/Si tandem module, displaying maintained performance across varied diffusivity conditions for the LSC component. Finally, we model the tandem module performance using a ray optic simulation-based multiphysics model and forecast a pathway for high efficiency tandem LSC/Si module performance.

14 SOLAR ENERGY↗
DOE OSTI2022

Second group of irradiation capsules: property data of irradiated welded stainless steel 347 and irradiated, welded, and hydrogen charged Zircaloy-4 for SHINE

Zircaloy-4 and AISI 347 stainless steel were irradiated to low doses (10 20 and 10 21 n/cm 2 ) at low temperature (~60°C) in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL). These materials were under consideration for some of the structural components of the medical isotope production facility developed by SHINE Technologies. Zircaloy-4 base metal, as welded, welded and post-weld heat treated (PWHT), and hydrogen charged samples were irradiated. AISI 347 base metal from Sandmeyer Steel, Penn Stainless, and Rolled Alloys suppliers were irradiated. AISI 347 gas tungsten arc welding (GTAW) and flux-cored arc welding (FCAW) samples of Penn Stainless and Rolled Alloys were also irradiated. The irradiated materials were tested with microhardness and tensile tests at room temperature in air. The AISI 347 materials had more elongation after irradiation than the Zircaloy-4 materials. In fact, the Zircaloy-4 welded without PWHT and with H charging had the lowest elongation of any of the materials. This report is the final in a series of reports on this project.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Novel Microshear Geometry for Exploring the Influence of Void Swelling on the Mechanical Properties Induced by MeV Heavy Ion Irradiation

Small disks are often the specimen of choice for exposure in nuclear reactor environments, and this geometry invariably limits the types of mechanical testing that can be performed on the specimen. Recently, shear punch testing has been utilized to evaluate changes arising from neutron irradiation in test reactor environments on these small disk specimens. As part of a broader effort to link accelerated testing using ion irradiation and conventional neutron irradiation techniques, a novel microshear specimen geometry was developed for use with heavy-ion irradiated specimens. The technique was demonstrated in pure Cu irradiated to 11 and 110 peak dpa with 10 MeV Cu ions. At 11 peak dpa, the Cu specimen had a high density of small voids in the irradiated region, while at 110 peak dpa, larger voids with an average void swelling of ~20% were observed. Micropillar and microshear specimens both exhibited hardening at 11 dpa, followed by softening at 110 dpa. The close alignment of the new microshear technique and more conventional micropillar testing, and the fact that both follow intuition, is a good first step towards applying microshear testing to a wider range of irradiated materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Thermo-Mechanical Distortion of Tungsten-Coated Steel During High Heat Flux Testing Using Plasma Arc Lamps

An experimental setup and a test section were designed and fabricated for high heat flux testing (HHFT) of neutron-irradiated specimens using water-wall plasma arc lamps. Because of the radiological considerations and limitations of reactor irradiation, the size of the test articles was limited to disks less than 10 mm in diameter. The specimen was clamped onto an actively cooled block, and clamping allowed the insertion of several thermocouples on the back surface of the specimen through a copper (Cu) block. Five vacuum plasma sprayed tungsten (W)–coated F82H steel specimens were subjected to HHFT. Surface profilometry measurements, which were conducted after HHFT, revealed central bowing of the top W surface. This type of residual distortion occurred for all of the specimens, and the larger the specimens were, the larger was the distortion.In an attempt to understand specimen distortion and address the science questions related to the testing of subsize specimens during HHFT, a simplified thermo-mechanical model was developed. By using a measured temperature in the Cu as an isothermal boundary condition, the model eliminated the need for coupling cooling fluid flow models with stress models, greatly simplifying the analysis. The main variable in the proposed model is hC, i.e., the thermal contact conductance between the F82H and the Cu washer. Inelastic properties, including hardening properties, were considered for F82H steel and Cu. Numerical simulation results demonstrated a buildup of residual deformation during HHFT and a very complex state of stress and deformation during typical heat flux (HF) cycling. Additionally, hoop stress evolution during a high heat flux cycle reveals that F82H at an interface with W would be mainly in compression during HF application and experienced a transition to a tension state during cooldown. Also, specimen distortion evolves during each HF cycle, as the specimen bows downward during HF application and upward during the cooldown period between HF cycles. The final specimen distortion, i.e., upward bowing of the specimen center, was qualitatively predicted for hC values of 4000 to 5000 W/(m 2 ·K). This hC range of values, for which bulging is obtained, is at the lower spectrum of the range of values for hC, consistent with the low thermal contact conductance expected from the unpolished F82H surface.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Microstructural changes of proton irradiated Hastelloy-N and in situ micropillar compression testing of one single grain at different local damage levels

Here, in situ micropillar compression was used to study the deformation of proton-irradiated Hastelloy-N at different damage levels. Multiple pillars were prepared from a single domain along the cross-section of 2.5 MeV proton-irradiated Hastelloy-N. Depending on the location of micropillars, the critical resolved shear stress was obtained as a function of local damage levels. Such an approach eliminates the variation of yield stress due to the difference in the Schmid factor. Microstructural characterization showed that irradiation hardening is contributed by complicated defect structures, including (a) dislocation loops with many in corduroy-like alignments, (2) dislocations pile up, and (3) Cottrell atmosphere. Silicon atoms are found to segregate at dislocation lines and loops and form complicated Cottrell cloud patterns. The critical resolved shear stress, $t_{crss}$, and hardening exponents were both extracted as a function of displacements per atom values up to 2.3. There was a 60% increase in $t_{crss}$ at the highest damage level.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Sensitivity of ATF Experiments in the Center Flux Trap of the Advanced Test Reactor to Adjacent Experiments

Irradiation experiments conducted in the Idaho National Laboratory’s Advanced Test Reactor are typically assumed to have little effect on one another. This assumption does not hold true for certain experiments in close proximity. To evaluate the impacts on safety and programmatic parameters of experiments in the center flux trap, the contents of the adjacent H and inner-A positions were modeled with a range of possible irradiation targets. First, neutron flux maps with experiments in those positions were compared against a baseline configuration. Next, several safety and programmatic parameters for a generic accident-tolerant fuel test train were calculated. It was shown that these parameters can exhibit considerable sensitivity to the contents of the H and A experiment positions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

FAST Irradiations, Postirradiation Examinations, and Modeling of U-Mo for Light Water Reactor Applications

Many next generation light water reactor (LWR) concepts, such as mobile small modular reactors, are seeking to use smaller core dimensions than conventional reactor types. Smaller reactor cores require an increase in fissile material to maintain reactivity. For non-proliferation purposes, enrichment increases are limited to less than 20% (high assay low enriched uranium, [HALEU]) and so higher uranium density fuels than UO 2 must be considered. To this end, uranium-molybdenum alloys were tested using the Fission Accelerated Steady-state Test (FAST) approach. The experiment test matrix is focused on identifying the temperature transition between low swelling and high fission gas retention to break away swelling and low fission gas retention. This paper documents the results of irradiation tests and post-irradiation examinations (PIE) including neutron radiography, rodlet profilometry, fission gas collection analysis, and optical metallography. The results of these tests showed that unconstrained U-Mo fuels (solid, Na-bonded rodlets) have a swelling threshold between 400-450°C with minimal fission gas release below this point. Higher temperature solid fuel showed microstructural zoning with small pore networks while lower temperature solid fuels have a uniform microstructure with large pore networks. U-Annular Mo fuels where swelling had some self-constraint imposed upon it, were shown to have much reduced swelling compared to their solid counterparts as well as very low fission gas release for irradiation temperatures up to 500°C. These initial results show that the use of U-Mo in constrained fuel geometries could be used as a high uranium density HALEU fuel for LWRs.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Tensile properties of the neutron irradiated HT-9 ACO-3 duct

HT-9, a ferritic-Martensitic steel, has attracted significant interest as a structural and cladding material for a variety of high dose nuclear component applications. This study examines the tensile properties of a HT-9 fuel assembly duct from the fast flux test facility, FFTF. The duct, from the Advanced Core Oxide-3 (ACO-3) irradiation test, was subjected to fast neutron irradiation exposure ranging from 3 dpa above the core top to nearly 155 dpa near the core mid-plane, spanning a temperature range from 382 °C at the lower end to 504 °C at the top. Due to the combination of thermal and neutron flux gradients along the core height. This yields a variety of irradiation damage processes which depend on core location. Tensile properties of specimens extracted at different positions along the height of the irradiated duct were measured at 25 °C, 200 °C and near their in-core irradiation temperature. The results show temperature has a greater impact than dose on post-irradiation strength and ductility. Two irradiation temperature regimes were determined, below irradiation temperatures of 420 °C irradiation hardening increases as irradiation temperature decreases, and above that temperature relatively minor changes are observed in tensile properties. These results are discussed in terms of expected microstructural changes, indicating that dislocation content is a strong contributor in these findings.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

HRMT-60- RaDIATE Material Studies

HRMT-60 experiment was performed at the CERN-HiRadMat facility in October 2022 to understand thermal shock response of conventional materials and novel materials to support the design and operation of future multi-MW accelerator beam windows and secondary particle-production targets. This experiment, organized within the framework of the RaDIATE collaboration, builds on the previous HRMT-43 (BeGrid2) experiment, where a variety of materials in both non-irradiated and previously proton-irradiated conditions were tested. The primary goal was to understand the failure mechanisms, limits and flow behavior of the various material specimens, as well as compare and contrast the thermal shock response of previously irradiated materials to their non-irradiated counterparts. A total of 120 samples were tested at different beam conditions. This poster will present the preliminary results of several materials tested during this experiments.

Ammigan, K.↗
DOE OSTI2023

Final CRADA Report: Accelerated Burn-up Accumulation Test of Clean Core Thorium Energy Designated ANEEL Fuel

Clean Core Thorium Energy (CCTE), LLC, located in Oak Brook, Illinois, is committed to the development of alternative nuclear fuels. CCTE is focused on leveraging the inherent benefits of thorium to create a novel nuclear fuel solution for our worlds growing power demand. Unlike some other fuel cycles proposing to use thorium in advanced reactors, CCTE is focused on deploying solid fuel designs (ceramic pellets in metallic cladding) in existing pressurized heavy-water reactors (PHWRs) and Canada deuterium uranium (CANDU) reactors. CCTE’s fuel design, referred to as Advanced Nuclear Energy for Enriched Life (ANEEL), uses mixed thorium-uranium oxide ((Th,U)O2) to enhance reactor operational strategies while producing significantly low attractiveness material in terms of nuclear proliferation. The overall project objective is to investigate the performance of high burnup ANEEL fuel via an irradiation experiment to be performed in the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL). The scope of work for this CRADA was specifically aimed at performing conceptual design and analysis to support development of an irradiation test rig, development of a fuel fabrication process for the experiment pellets, fabrication and qualification of the pellets, and shipment of the pellets to INL so they can be used to construct experiment rodlets.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

The use of U3Si2/Al dispersion fuel for high power research reactors

In order to investigate the irradiation performance of U3Si2/Al dispersion fuel at relatively aggressive reactor conditions, compared to how this fuel is typically used in a research or test reactor, post irradiation examination was performed on two fuel plates that were irradiated at ~270 W/cm2 average surface heat flux and to a maximum local burnup greater than 8 × 1021 fissions/cm3 in the Advanced Test Reactor as part of the RERTR-8 experiment. As part of the non-destructive examinations that were performed on both fuel plates, detailed thickness measurements using a high-fidelity measurement bench were performed on one fuel plate and a segment of the second fuel plate. This paper provides the first reported results of such high-resolution thickness measurements for U3Si2/Al dispersion fuel plates, containing primarily the U3Si2 fuel phase, irradiated at such power levels to high burnup. For destructive examination using optical metallography, samples were generated from both irradiated plates. Localized regions of high swelling (characteristic of internal blistering) were observed on the surface of both fuel plates, suggesting that the performance limits had been reached for each plate. Destructive examinations showed that the fuel particles that are primarily U3Si2, which become amorphous during irradiation, in both plates contained relatively large fission gas bubbles with evidence of fission gas bubble interconnection.

Wachs, Daniel M.↗
DOE OSTI2024

UNCERTAINTIES FOR IN-REACTOR TESTING OF TRITIUM LOADED GETTERS WITH TEMPERATURE CONTROL

The fourth experiment in TPBAR Materials Irradiation Separate-Effects Test (TMIST) series (TMIST-4) is planned to experimentally determine the effect of neutron irradiation on the equilibrium vapor pressure of tritium over a tritium loaded Nickel-Plated Zirconium (NPZ) getter in a simulated TPBAR service environment. This pressure will be used to estimate the tritium permeation rate. In the thermal design in the TMIST-4, two evaluations are required. 1) The cladding temperature is calculated to estimate the feasibility of detecting potential irradiation enhancement of the partial pressure for an NPZ getter. This work is required to obtain a precise cladding temperature for measurement of a low tritium partial pressure. This work has been completed and indicated that the required/target cladding temperatures based on the TMIST-4 test plan can be satisfied under the test condition range by modifying the capsule component shapes and inserting a thermally conductive metal sleeve. 2) The evaluation of uncertainties associated with the test design and operation is performed. This includes fabrication tolerances, and power and nuclear operating conditions. These factors will impact the component temperatures inside capsules and resulting the tritium partial pressure. The tritium permeation rate is a function of temperature and tritium partial pressure. The prediction of tritium permeation rates affects the feasibility of obtaining measurement resolutions required to reach reasonable conclusion for potential irradiation enhanced performance. This work will investigate the uncertainties.

TTP, TPBAR, TMIST-4, TPBAR Materials Irradiation S↗
DOE OSTI2022

Steady-State Irradiation of Characterized Instruments for Nuclear Thermal Rockets Using In-Pile Experiment Apparatus

The development of nuclear rocket technology is critical for further exploration of extra-terrestrial bodies. Nuclear rockets can provide various advantages over current chemical rockets. However, the harsh environment provides several challenges regarding instrument performance. Temperature extremes, radiation (reactor and space), and the inability to conduct traditional maintenance activities can lead to severe degradation in instrument performance. To better understand the effects of radiation on instrumentation, an irradiation campaign has been designed to test a set of instruments provided by a collaborator in the aerospace industry. Details concerning instrument performance before and after irradiation are provided to allow for an analysis of the tested instruments. Additionally, the design of the irradiation test is described in detail.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

A mechanism-based quantitative multi-scale framework for investigating irradiation hardening of tungsten at low temperature

We present the development and validation of a mechanism-based multi-scale modeling framework to quantitatively link the irradiation defect evolution kinetics at the microscopic scale to the macroscopic yield strength and flow stress evolution of tungsten irradiated at low temperature (0.08 < T/T m < 0.18, where T m is the melting point and is equal to 3673 K). The mechanism-based strength model, proposed as the superposition of thermal softening and modified dispersed barrier hardening, is developed to understand the underlying strengthening mechanisms. The thermal softening exponent as defined in the Johnson-Cook model is obtained by fitting unirradiated yield strength at different temperatures. A set of irradiation-induced defect kinetics equations with the thermodynamics parameters derived from the atomic calculations reported in the literature is used to determine the densities and sizes of defect clusters at the meso-scale, and the predicted irradiation damage characteristics are in reasonable quantitative agreement with experimental data from literature. The effects of irradiation condition (temperature and irradiation dose) and test temperature on yield strength are quantitatively predicted and compared with experimental measurements from the literature. Here, the predicted irradiation hardening and strain hardening are compared with experimental data as model validation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Comparative post-irradiation examination of high burnup U-19Pu-10Zr: Assessing steady-state irradiation behavior against historical and modeled fuel performance

Here, the development of next-generation sodium-cooled fast reactors necessitates comprehensive research on metallic fuels to maximize economic performance while ensuring safe operation. In this study, we investigated the steady-state irradiation behavior of two high burnup U-19Pu-10Zr fuel pins, DP-36 and DP-40, in preparation for planned safety testing. Post-irradiation examination (PIE) was performed to quantify fuel column elongation, regions of low-density at the top of the fuel column, pin deformation, fission product distribution, fractional fission gas release, microstructural evolution, and fuel constituent redistribution. Benchmarking against existing PIE data from U-19Pu-10Zr fuel pins irradiated in EBR-II revealed consistent patterns in fuel column elongation and cladding diametral strain. However, both pins exhibited longer low-density structures, and destructive examination of DP-36 revealed more complex constituent redistribution patterns compared to previously reported data for ternary fuel pins. The steady-state irradiation of both pins was also modeled using BISON. Comparisons of PIE results with modeled predictions showed overall agreement in fractional fission gas release but consistent overestimation of axial and radial swelling due to gaseous and solid swelling models. These findings underscore the critical importance of pre-test characterization on test and sibling pins to accurately capture steady-state fuel behavior ahead of transient testing, thus establishing a baseline for post-test comparison. Additionally, these analyses identified key data gaps that warrant further investigation to improve the understanding and prediction of fuel swelling, thereby enhancing the synergy between modeling and experimental efforts in supporting accident testing.

BISON↗
DOE OSTI2025

AGC-2 Graphite Preirradiation Data Analysis Report

This report describes the specimen loading order and documents all preirradiation examination material property measurement data for graphite specimens contained within the Second Advanced Graphite Capsule (AGC 2) irradiation capsule. The AGC 2 capsule is the second in six planned irradiation capsules comprising the Advanced Graphite Creep (AGC) test series. The AGC test series is used to irradiate graphite specimens in order to garner quantitative data necessary for predicting the irradiation behavior and operating performance of new nuclear grade graphites. This testing will ascertain the in service behavior of the graphite for pebble bed and prismatic very high temperature reactor designs. Similar to the First Advanced Graphite Capsule (AGC 1) preirradiation examination report, material property tests were conducted on specimens from 18 nuclear grade graphite types. However, AGC 2 tested an increased number of specimens (i.e., 512) prior to loading them into the AGC 2 irradiation assembly. All AGC 2 specimen testing was conducted at Idaho National Laboratory from July 2009 to August 2010. This report also details the specimen loading methodology for graphite specimens inside the AGC 2 irradiation capsule. The AGC 2 capsule design requires “matched pair” creep specimens that have similar dose levels above and below the neutron flux profile mid plane. This provides similar specimens with and without an applied load. Analysis in this document utilizes the neutron flux profile calculated for the AGC 2 capsule design, the capsule dimensions, and the size (i.e., length) of the selected graphite specimens to create a stacking order that produces “matched pairs” of graphite specimens above and below the AGC 2 capsule elevation mid point, thus providing specimens with similar neutron dose levels.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗