SEARCH · Search NASA

Results for “lamination”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Analysis of matrix cracking and local delamination in (0/theta/-theta)s graphite epoxy laminates under tensile load

Three-dimensional element analyses of (0/theta/-theta)s graphite epoxy laminates, where theta = 15, 20, 25, 30, and 45 deg, subjected to axial tensile load, were performed. The interlaminar stresses in the theta/-theta interface were calculated with and without a matrix crack in the central -theta plies. The interlaminar normal stress changes from a small compressive stress when no matrix crack is present to a high tensile stress at the intersection of the matrix crack and the free edge. The analysis of local delamination from the -theta matrix crack indicates a high strain energy release rate and a localized Mode I component near the free edge, within one-ply distance from the matrix crack. To examine the stress state causing the matrix cracking, the maximum principal normal stress in a plane perpendicular to the fiber direction in the -theta ply was calculated in an uncracked laminate. The corresponding shear stress parallel to the fiber was also calculated. The principal normal stress at the laminate edge increased through the ply thickness and reached a very high tensile value at the theta/-theta interface indicating that the crack in the -theta ply may initiate at the theta/-theta interface.

Salpekar, S. A.↗

NASA NTRS1993

Effect of boundary conditions and panel geometry on the response of laminated panels subjected to transverse pressure loads

The behavior of thin laminated flat and curved panels subjected to transverse pressure and inplane loads is considered. The effects of panel geometry, boundary conditions and laminate stacking sequence on the response of panels subjected to transverse pressure loads up to 12.4 N/sq cm is presented. The response of thin laminated panels is evaluated analytically and selected results are compared with test data. A parametric study of the deformation and strain responses of panels with radius of curvature ranging from 20 to 305 cm is presented. The combination of inplane tensile and pressure loads is also considered.

Jegley, Dawn C.↗

NASA NTRS1994

Improved PMR Polyimides For Heat-Stable Laminates

Second-generation PMR-type polyimides (PMR-II polyimides) of enhanced thermo-oxidative stability prepared by substitution of para-aminostyrene (PAS) end caps for nadic-ester (NE) end caps used in prior PMR-II polyimides. Laminates unidirectionally reinforced with graphite fibers and made with PAS-capped resins exhibited thermo-oxidative stabilities significantly greater than those of similar laminates made with NE-capped PMR-II resins. One new laminate exhibited high retention of weight and strength after 1,000 h of exposure to air at 371 degrees C.

Vannucci, R. D.↗

NASA NTRS1993

Stochastic damage evolution in textile laminates

A probabilistic model utilizing random material characteristics to predict damage evolution in textile laminates is presented. Model is based on a division of each ply into two sublaminas consisting of cells. The probability of cell failure is calculated using stochastic function theory and maximal strain failure criterion. Three modes of failure, i.e. fiber breakage, matrix failure in transverse direction, as well as matrix or interface shear cracking, are taken into account. Computed failure probabilities are utilized in reducing cell stiffness based on the mesovolume concept. A numerical algorithm is developed predicting the damage evolution and deformation history of textile laminates. Effect of scatter of fiber orientation on cell properties is discussed. Weave influence on damage accumulation is illustrated with the help of an example of a Kevlar/epoxy laminate.

Dzenis, Yuris A.↗

NASA NTRS1994

The effects of embedded internal delaminations on composite laminate compression strength; an experimental review

Delaminations in laminated composite materials can degrade the compressive strength of these materials. Delaminations can form as a result of impact damage or processing flaws. In order to better understand the effects of these delaminations on the compressive behavior of laminated composite plates, programs have been conducted to assess the criticality of prescribed delaminations of known size, shape, and location on the compression strength of laminated composites. A review of these programs is presented along with highlights of pertinent findings from each.

Nettles, Alan T.↗

NASA NTRS1994

Preliminary evaluation of hybrid titanium composite laminates

In this study, the mechanical response of hybrid titanium composite laminates (HTCL) was evaluated at room and elevated temperatures. Also, the use of an elastic-plastic laminate analysis program for predicting the tensile response from constituent properties was verified. The improvement in mechanical properties achieved by the laminates was assessed by comparing the results of static strength and constant amplitude fatigue tests to those for monolithic titanium sheet. Two HTCL were fabricated with different fiber volume fractions, resin layer thicknesses, and resins. One panel was thicker and was more poorly bonded in comparison to other. Consequently, the former had a lower tensile strength, while fewer cracks grew in this panel and at a slower rate. Both panels showed an improvement in fatigue life of almost two orders of magnitude. The model predictions were also in good agreement with the experimental results for both HTCL panels.

Miller, J. L.↗

NASA NTRS1994

On the laminated structure of ozone in the sub-tropical atmosphere

Ozone data recorded by balloon-borne sondes released at various sites around the world revealed that frequently the vertical ozone distribution in the stratosphere is remarkably laminated. Recently, measurements of ozone profiles near the winter polar vortex have shown strong laminae close to the vortex boundary. Also, a statistical study published recently has shown that laminae are most commonly found between 12 and 18 km at high latitudes in winter and spring in both hemispheres but they are not found in the tropics and are rarely observed in the subtropics. Ozonesonde ascents performed in Athens (37.9 deg N, 23.8 deg E) during the winter 1991-1992 in the framework of the European Arctic Stratospheric Ozone Experiment (EASOE) have shown that the lamination phenomenon was very frequently present in our region which is in contradiction with previous measurements at our latitudes. The characteristic minimum of ozone at 15 km has been also detected. Finally, the correlation of the occurrence of these two phenomena in relation with the circulation of air masses showed that the laminated profiles are connected in the lower stratosphere while the appearance of the ozone minimum around 15 km is connected with the influence of the subtropical jet-stream.

Varotsos, Costas↗

NASA NTRS1994

Basic mechanics of laminated composite plates

The mechanics of laminated composite materials is presented in a clear manner with only essential derivations included. The constitutive equations in all of their forms are developed and then summarized in a separate section. The effects of hygrothermal effects are included. The prediction of the engineering constants for a laminate are derived. Strength of laminated composites is not covered.

Nettles, Alan T.↗

NASA NTRS1992

Static and dynamic strain energy release rates in toughened thermosetting composite laminates

In this work, the static and dynamic fracture properties of several thermosetting resin based composite laminates are presented. Two classes of materials are explored. These are homogeneous, thermosetting resins and toughened, multi-phase, thermosetting resin systems. Multi-phase resin materials have shown enhancement over homogenous materials with respect to damage resistance. The development of new dynamic tests are presented for composite laminates based on Width Tapered Double Cantilevered Beam (WTDCB) for Mode 1 fracture and the End Notched Flexure (ENF) specimen. The WTDCB sample was loaded via a low inertia, pneumatic cylinder to produce rapid cross-head displacements. A high rate, piezo-electric load cell and an accelerometer were mounted on the specimen. A digital oscilloscope was used for data acquisition. Typical static and dynamic load versus displacement plots are presented. The ENF specimen was impacted in three point bending with an instrumented impact tower. Fracture initiation and propagation energies under static and dynamic conditions were determined analytically and experimentally. The test results for Mode 1 fracture are relatively insensitive to strain rate effects for the laminates tested in this study. The test results from Mode 2 fracture indicate that the toughened systems provide superior fracture initiation and higher resistance to propagation under dynamic conditions. While the static fracture properties of the homogeneous systems may be relatively high, the apparent Mode 2 dynamic critical strain energy release rate drops significantly. The results indicate that static Mode 2 fracture testing is inadequate for determining the fracture performance of composite structures subjected to conditions such as low velocity impact. A good correlation between the basic Mode 2 dynamic fracture properties and the performance is a combined material/structural Compression After Impact (CAI) test is found. These results underscore the importance of examining rate-dependent behavior for determining the longevity of structures manufactured from composite materials.

Cairns, Douglas S.↗

NASA NTRS1992

Mechanisms of compressive failure in woven composites and stitched laminates

Stitched laminates and angle interlock woven composites have been studied in uniaxial, in-plane, monotonic compression. Failure mechanisms have been found to depend strongly on both the reinforcement architecture and the degree of constraint imposed by the loading grips. Stitched laminates show higher compressive strength, but are brittle, possessing no load bearing capacity beyond the strain for peak load. Post-mortem inspection shows a localized shear band of buckled and broken fibers, which is evidently the product of an unstably propagating kink band. Similar shear bands are found in the woven composites if the constraint of lateral displacements is weak; but, under strong constraint, damage is not localized but distributed throughout the gauge section. While the woven composites tested are weaker than the stitched laminates, they continue to bear significant loads to compressive strains of approx. 15 percent, even when most damage is confined to a shear band.

Cox, B. N.↗

NASA NTRS1992

Buckling behavior of long symmetrically laminated plates subjected to combined loads

A parametric study of the buckling behavior of infinitely long symmetrically laminated anisotropic plates subjected to combined loadings is presented. The loading conditions considered are axial tension and compression, transverse tension and compression, and shear. Results obtained using a special purpose analysis, well suited for parametric studies are presented for clamped and simply supported plates. Moreover, results are presented for some common laminate constructions, and generic buckling design charts are presented for a wide range of parameters. The generic design charts are presented in terms of useful nondimensional parameters, and dependence of the nondimensional parameters on laminate fiber orientation, stacking sequence, and material properties is discussed. An important finding of the study is that the effects of anisotropy are much more pronounced in shear-loaded plates than in compression loaded plates. In addition, the effects of anisotropy on plates subjected to combined loadings are generally manifested as a phase shift of self-similar buckling interaction curves. A practical application of this phase shift is the buckling resistance of long plates can be improved by applying a shear loading with a specific orientation. In all cases considered, it is found that the buckling coefficients of infinitely long plates are independent of the bending stiffness ratio (D sub 11/D sub 22) sup 1/4.

Nemeth, Michael P.↗

NASA NTRS1992

Characteristics of laminates with delamination control strips

Tough resin is needed to resist delamination crack propagation. However, modulus often has to be compromised because it is difficult to retain both high modulus and toughness in a matrix material. A potential solution is to use a hybrid system in which tough resin strips are included within a conventional matrix composite. By adjusting the spacing of the tough resin strips, maximum delamination size can be controlled. Experimental results for impact damage and subsequent damage propagation in laminates containing tough resin strips are reported. Plain adhesive strips and fiber-reinforced tough resin composite strips were used in constructing the hybrid laminates. Test results indicated that size of delamination inflicted by impact was confined between the tough resin strips. As a result, significantly increased residual compressive strength was obtained. Impacted laminates containing tough resin strips were also fatigue tested. It was found that these strips reduced the growth of the impact damage area relative to the growth seen in coupons with no tough resin strips. Damage growth from an open hole under tension fatigue was evaluated using both tough resin strips and glass fiber reinforced tough resin strips. Unreinforced tough resin strips retarded delamination growth from the open hole, but did not stop matrix cracks growing in the fiber direction. Fiber reinforced tough resin strips did not contain axial delamination growth from the open hole. However, they did act as crack arresters, stopping the through-the-thickness tension crack originating from the hole.

Sun, C. T.↗

NASA NTRS1993

Master plot analysis of microcracking in graphite/epoxy and graphite/PEEK laminates

We used a variational stress analysis and an energy release rate failure criterion to construct a master plot analysis of matrix microcracking. In the master plot, the results for all laminates of a single material are predicted to fall on a single line whose slope gives the microcracking toughness of the material. Experimental results from 18 different layups of AS4/3501-6 laminates show that the master plot analysis can explain all observations. In particular, it can explain the differences between microcracking of central 90 deg plies and of free-surface 90 deg plies. Experimental results from two different AS4/PEEK laminates tested at different temperatures can be explained by a modified master plot that accounts for changes in the residual thermal stresses. Finally, we constructed similar master plot analyses for previous literature microcracking models. All microcracking theories that ignore the thickness dependence of the stresses gave poor results.

Nairn, John A.↗

NASA NTRS1994

Response of laminated composite plates to low-speed impact by different impactors

An analytic procedure has been developed to determine the transient response of simply supported, retangular laminated composite plates subjected to impact loads from airgun-propelled or drop-weight impactors. A first-order shear deformation theory has been included in the analysis to represent properly any local short-wavelength transient bending response. The impact force has been modeled as a locally distributed load with cosine-cosine distribution. A double Fourier series expansion and the Timoshenko small increment method have been used to determine the contact force, out-of-plane deflections, and in-plane strains and stresses at any plate location due to an impact force at any plate location. The results of experimental and analytical studies are compared for quasi-isotropic laminates. The results indicate the importance of including transverse shear deformation effects in the analysis for predicting the response of laminated plates subjected to both airgun-propelled and dropped-weight impactors. The results also indicate that plate boundary conditions influence the axial strains more significantly than the contact force for a dropped-weight impactor. The results of parametric studies identify a scaling approach based on impactor momentum that may account for the differences in the responses of plates impacted by airgun-propelled or dropped-weight impactors.

Prasad, Chunchu↗

NASA NTRS1995

Prediction of microcracking in composite laminates under thermomechanical loading

Composite laminates used in space structures are exposed to both thermal and mechanical loads. Cracks in the matrix form, changing the laminate thermoelastic properties. An analytical methodology is developed to predict microcrack density in a general laminate exposed to an arbitrary thermomechanical load history. The analysis uses a shear lag stress solution in conjunction with an energy-based cracking criterion. Experimental investigation was used to verify the analysis. Correlation between analysis and experiment is generally excellent. The analysis does not capture machining-induced cracking, or observed delayed crack initiation in a few ply groups, but these errors do not prevent the model from being a useful preliminary design tool.

Maddocks, Jason R.↗

NASA NTRS1993

CCARES: A computer algorithm for the reliability analysis of laminated CMC components

Structural components produced from laminated CMC (ceramic matrix composite) materials are being considered for a broad range of aerospace applications that include various structural components for the national aerospace plane, the space shuttle main engine, and advanced gas turbines. Specifically, these applications include segmented engine liners, small missile engine turbine rotors, and exhaust nozzles. Use of these materials allows for improvements in fuel efficiency due to increased engine temperatures and pressures, which in turn generate more power and thrust. Furthermore, this class of materials offers significant potential for raising the thrust-to-weight ratio of gas turbine engines by tailoring directions of high specific reliability. The emerging composite systems, particularly those with silicon nitride or silicon carbide matrix, can compete with metals in many demanding applications. Laminated CMC prototypes have already demonstrated functional capabilities at temperatures approaching 1400 C, which is well beyond the operational limits of most metallic materials. Laminated CMC material systems have several mechanical characteristics which must be carefully considered in the design process. Test bed software programs are needed that incorporate stochastic design concepts that are user friendly, computationally efficient, and have flexible architectures that readily incorporate changes in design philosophy. The CCARES (Composite Ceramics Analysis and Reliability Evaluation of Structures) program is representative of an effort to fill this need. CCARES is a public domain computer algorithm, coupled to a general purpose finite element program, which predicts the fast fracture reliability of a structural component under multiaxial loading conditions.

Duffy, Stephen F.↗

NASA NTRS1995

A new merit function for evaluating the flaw tolerance of composite laminates

Advanced composite materials are providing notable savings in numerous aerospace and non-aerospace applications by virtue of their uniquely high strength-to-density ratio and high stiffness-to-density ratio. However, their full potential for high performance has yet to be achieved because of the low tolerance of the 'brittle' material to impact, holes, flaws, and localized discontinuities due to relatively low toughness. In the present paper a new and simple merit function is proposed for maximizing the strength performance of flawed composite laminate for different design requirement. This new merit function takes into account the flaw tolerance of a composite laminated as well as its stiffness. After development of the new merit function, an example is presented of its application to a practical laminate family.

Mikulas, Martin M., Jr.↗

NASA NTRS1997

A New Merit Function for Evaluating the Flaw Tolerance of Composite Laminates: Arbitrary Size Holes and Center Cracks - Part 2

In a previous paper, a new merit function for determining the strength performance of flawed composite laminates was presented. This previous analysis was restricted to circular hole flaws that were large enough that failure could be predicted using the laminate stress concentration factor. In this paper, the merit function is expanded to include the flaw cases of an arbitrary size circular hole or a center crack. Failure prediction for these cases is determined using the point stress criterion. An example application of the merit function is included for a wide range of graphite/epoxy laminates.

Mikulas, Martin M., Jr.↗