Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Irradiation of UC1+x kernels using the MiniFuel vehicle: Microstructure, phase analysis, and initial post-irradiation examination

Uranium carbide is a candidate fuel form for a wide range of advanced reactors, including larger Generation IV reactors as well as small modular reactors and microreactors. However, its commercial deployment timeline faces challenges via traditional qualification approaches. To address this issue, an accelerated fission rate irradiation test was performed to collect basic fuel performance data to inform fuel performance models and potential future integral tests. Hyperstoichiometric UC (UC1+x) kernels were irradiated in the High Flux Isotope Reactor using the MiniFuel irradiation vehicle. The test matrix spanned two temperature regimes (700 °C and 800 °C) and burnup levels (1.8 % FIMA and 2.8 % FIMA). Between 21 and 63 kernels were tested at each unique temperature and burnup condition. As-fabricated microstructural analysis revealed a multiphase composition with UC, UC2, UC2−y, and U-C-O bearing phases for the irradiated kernels. Following irradiation, fission gas release, swelling, and microstructures were analyzed. Measured fission gas release was below 5 % for all irradiation conditions, reaching a maximum at the highest temperature and burnup condition. A binary swelling response was observed; the lower burnup and temperature conditions resulted in negligible swelling, but the higher burnup and temperature conditions produced significant anisotropic swelling and densification in a subset of kernels. The basic microstructural exams of kernels following irradiation were not capable of showing a correlation between kernels that exhibited excessive swelling and those that did not. Characterization of a subset of samples using the Advanced Photon Source and more detailed microstructural examination of unirradiated kernels revealed that a subset of kernels contained very high UC2 phase fractions. The anomalous swelling response is hypothesized to have been driven by this chemical variation. The results of this irradiation highlight the potential of accelerated fission rate irradiation testing to explore such behaviors and inform the development of fuel specifications.

Adorno Lopes, Denise [ORNL] (ORCID:000900023705987↗
DOE OSTI2018

Microstructural characterization of SiO2/Ni nanocomposites electrodeposited from a sulphate bath modified by PEI

Highlights: • SiO{sub 2}/Ni + PEI nanocomposites are deposited from the sulphate bath containing PEI. • PEI allows incorporation of higher SiO{sub 2} vol% in SiO{sub 2}/Ni + PEI nanocomposites. • PEI in the form of a thin layer surrounds spherical Ni nanograins and SiO{sub 2} clusters. • PEI action ensures high hardness, tribological properties and corrosion resistance. - Abstract: SiO{sub 2}/Ni nanocomposite coatings containing well-dispersed SiO{sub 2} nanoparticles were electrodeposited from a sulphate bath with and without the addition of polyethylenimine (PEI) as a cationic surfactant. The surface morphology and microstructure in the cross-sections of the deposited nanocomposites were examined by scanning electron microscopy. More detailed microstructure characterization was performed using transmission, scanning-transmission and high resolution transmission electron microscopy. It was determined that the addition of 0.05 g/L and 0.1 g/L of PEI allows the incorporation of SiO{sub 2} nanoparticles in the nickel matrix to be increased in comparison with the nanocomposite deposited without a surfactant. Based on high spatial resolution microanalysis, performed using high count rate energy dispersive spectroscopy of characteristic X-rays in the scanning-transmission mode, the distribution of SiO{sub 2} nanoparticles in the nanocomposite was visualized on elemental maps. Image analysis of the electron microscopy images enabled the mean equivalent circle diameters of grains in the nickel matrix to be determined, together with the volume fraction of SiO{sub 2} nanoparticles in the nanocomposites. The volume fraction of SiO{sub 2} clusters in the SiO{sub 2}/Ni + PEI nanocomposites with the addition of 0.05 g/L and 0.1 g/L of PEI is equal to 18.4% and 13.3%, respectively. Furthermore, the PEI addition allows the nickel grain size in the matrix to be reduced. The combination of different imaging techniques confirmed that PEI is not only present as a surfactant in the electrolytic bath, but also incorporates into the microstructure of the nanocomposite. Nanocomposites electrodeposited in the presence of 0.05 g/L of PEI exhibit higher hardness, good tribological properties and improved corrosion resistance. Although increasing the PEI concentration in the bath up to 0.1 g/L strongly promotes grain size reduction and increase of the SiO{sub 2} volume fraction, it also causes an increase in the PEI fraction embedded in the microstructure, which results in deterioration of the properties of the SiO{sub 2}/Ni + PEI nanocomposites.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2018

Densification, microstructure and properties of TiB2 ceramics fabricated by spark plasma sintering

Highlights: • Nearly full densification of in-house processed TiB{sub 2} ceramic powders at 1500 °C. • Microstructures revealing the size and shape of TiB{sub 2} grains after SPS. • The effect of sub-micron particles on the densification during SPS. • The effect of sintering pressure on the microstructure. • Microhardness and nano-indentation measurements along with oxidation studies. - Abstract: This study reports the fabrication of high-density TiB{sub 2} ceramics at reduced temperatures (1500 °C) by using field assisted sintering technology/spark plasma sintering (FAST/SPS) technique. In-house processed TiB{sub 2} powders with high purity were employed as starting materials. The effects of SPS conditions on the sintering behavior and microstructure of TiB{sub 2} were investigated. Sub-micron character of TiB{sub 2} particles has a strong influence on the densification during SPS. Microstructural analyses revealed that the high pressure affected both the grain size and the shape of TiB{sub 2} crystallites. Elongated grains with average size of 6 μm were perceived in TiB{sub 2} sample fabricated by SPS at 1500 °C under 60 MPa pressure with a relative density of 96.7%. The microhardness and elastic modulus were measured as 27.4 GPa and 685.2 GPa, respectively. This sample revealed an improved oxidation resistance due to the formation of a thin oxidation layer on the surface when heated up to 1200 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Data clustering for the high-resolution alignment of microstructure and strain fields

The emergence of small-scale deformation mapping by a combination of scanning electron microscopy and digital image correlation (SEM-DIC) has enabled full-field investigations into the complex roles of microstructure on microscale deformation mechanisms. However, these investigations are hindered by errors in alignment between the microstructure data, generally acquired by electron backscatter diffraction (EBSD), and the microscale strain data obtained by SEM-DIC. Distortions, stitching artifacts, and spatial resolution differences between microstructure and strain fields can lead to misalignments on the order of μms. This alignment uncertainty introduces error into microstructure-strain localization analyses and precludes the examination of deformation mechanisms near grain boundaries. To improve alignment between EBSD-obtained grain boundaries and SEM-DIC strain data, an approach was created wherein a mantle was first established around the EBSD-acquired grain boundaries. Strain data was then clustered within this mantle using a k-means algorithm to identify grain boundary strain localization, and these boundary points were fit to obtain a continuous curve for each individual boundary. Clustered point outliers, such as those due to grain boundary-local dislocation slip, were statistically identified by using an absolute error threshold and removed from the grain boundary fit. The ending identification of grain boundaries in the microscale strain data is significantly improved from EBSD-identified boundaries.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Strain rate sensitivity, microstructure variations, and stress-assisted β → α" phase transformation investigation on the mechanical behavior of dual-phase titanium alloys

In this study, the microstructures of three widely used dual-phase titanium alloys: Ti-6Al-4V, Ti-6Al-2Sn-4Zr-2Mo, and Ti-6Al-2Sn-4Zr-6Mo are characterized using backscatter electron imaging and the deformation behaviors in their individual α and β phases are investigated using in situ high-energy X-ray diffraction during uniaxial tension experiments. This is accompanied by calculation of the strain rate sensitivity (SRS) in these alloys, as a function of applied loading. The results of the calculated SRS and the mechanical response (in terms of lattice strains and hardening behaviors) are rationalized based on the local microstructure, composition, and texture of the alloy. A stress-induced β (BCC) to α" (orthorhombic) phase transformation is observed during the in-situ diffraction experiment, which permitted analysis of the lattice strain evolution during the phase transformation. Results from this study provide insights into the relationship between microstructure, composition, applied loading, and the deformation behavior, including effects on loading with time holds. Specifically, the results show that the microstructure, and not necessarily the chemical composition (Mo content), along with the applied loading have a dominant role in the observed SRS variation in titanium alloys. Further, the evolution of the α" (orthorhombic) phase is observed for the first time during deformation of an industrially relevant titanium alloy, Ti-6246.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Microstructural stability of irradiated yttrium hydride under thermal cycles

Hydrides that retain their hydrogen in service are critical for advanced microreactor and space nuclear systems. Hydrogen retention is affected by evolving microstructure under temperature and irradiation extremes. This study investigated microstructural features in neutron-irradiated yttrium hydride and the stability of these features under thermal cycles. Differential scanning calorimetry was used to determine hydrogen desorption and temperatures at which significant phase changes are occurring, and transmission electron microscopy was used for microstructural analysis after each thermal cycle. Cyclic heating led to crystallization and epitaxial growth of surface oxidation and dehydriding of the matrix. Other features such as the bulk matrix crystal structure, irradiation-induced cavities, and matrix precipitation remained constant after thermal cycling. Results allow us to design better hydride alloys through microstructure tailoring and potential irradiation conditioning treatments.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructure and mechanical properties of hypoeutectic Al–6Ce–3Ni-0.7Fe (wt.%) alloy

Here, a hypoeutectic, Fe-modified Al–Ce–Ni alloy (Al–6Ce–3Ni-0.7Fe, wt.%) is studied in terms of microstructure, thermal stability, ambient temperature strengthening, and creep resistance. The as-cast microstructure consists of primary Al dendrites and interdendritic binary eutectic regions (Al–Al11Ce3 and/or Al–Al9(Fe,Ni)2), with micron/submicron lamellar spacing, depending on the location along the height of the ingot. The cast alloy exhibits excellent coarsening resistance at 400 °C, with mostly unchanged microstructure and microhardness after 6 weeks of aging, indicating good thermal stability of Al11Ce3 and Al9(Fe,Ni)2. Orowan strengthening and load transfer are identified as strengthening mechanisms at ambient and elevated temperature. A high volume fraction of the intermetallic phases (providing load transfer) and relatively coarse eutectic spacing (for modest Orowan strengthening) result in a moderate as-cast microhardness of 566 ± 32 MPa. Creep resistance at 300 and 350 °C is similar to a binary Al-12.5Ce eutectic alloy (with twice the Ce content) because of two countering effects: Al–6Ce–3Ni-0.7Fe shows a higher volume fraction of strengthening intermetallic phases, but it also exhibits a large fraction of primary Al dendrites which weaken the alloy. By contrast, the alloy, when laser-remelted at the surface, has a fully eutectic microstructure without primary aluminum dendrites achieved by high undercooling on solidification, with a refined network of eutectic phases that doubles the microhardness as compared to the cast alloy. Whereas coarsening is faster due to the shorter diffusion distances between the eutectic phases, hardness remains ~30% higher than the as-cast alloy after ~6 weeks aging at 400 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructural evolution in shear-punch tests: A comparative study of pure Cu and Cu-Cr alloy

Understanding the mechanisms behind microstructural evolution during shear deformation has been a long-standing area of interest. However, establishing a connection between microstructure, mechanical properties, and extent of shear deformation is challenging and requires refined experimental approaches. Shear-punch testing (SPT) provides a controlled method to introduce shear into small volumes of material that later can be subjected to detailed microstructural characterization. In this study, we utilize an SPT device to induce shear deformation to pure copper and a binary copper-chromium alloy. Electron backscatter diffraction and transmission electron microscopy were used to study the mechanisms of plastic deformation after SPT. Our results indicate that shear deformation of pure Cu produces a dense network of intercepting microshear bands upon sustained deformation. Twin boundaries undergo degradation into high angle grain boundaries due to simultaneous deviation from the axis-angle pair condition of 60° misorientation on [111] direction. The presence of 50% volume Cr particles in the soft Cu matrix fundamentally altered the shear deformation mechanism. Preferential deformation of the Cu matrix led to accelerated shear-induced formation of low and high angle grain boundaries, and subsequent grain refinement. Comparatively, no grain refinement occurred in pure Cu at a strain ~10 times larger (ϵ = 4.73) than that of the copper-chromium case (ϵ = 0.42). Overall, our study sheds light on the microstructural evolution during shear deformation and highlights the significant influence of particle reinforcements on the shear deformation mechanisms of metals.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of post-deposition heat treatment on microstructure and mechanical properties of NASA HR-1 cold spray coatings

The primary goal of this work was to examine the impact of heat treatment on the evolution of microstructure and mechanical properties of NASA HR-1 cold spray coatings. Coatings were produced employing a high pressure cold spray system using N2 and He process gases and the effect of process gas and deposition temperature on the microstructure and mechanical properties of the coatings was examined. Microstructural characterization was performed using optical microscopy, scanning electron microscopy, micro X-ray computed tomography, and electron backscatter diffraction. NASA HR-1 coatings produced with He process gas exhibited improved plastic deformation and resulted in the lowest porosity compared to those deposited with N2 process gas. All coatings showed brittle failure with limited ductility in the as-deposited condition. Heat treatment of the NASA HR-1 cold spray coatings was performed at 550°C and 950°C for 1 h to improve the mechanical strength of the coatings. Heat treatment improved the particle bonding and enhanced the mechanical properties of the cold spray coatings. Heat treatment performed at 550°C resulted in higher mechanical strength of coatings, whereas the heat treatment performed at 950°C resulted in recrystallized microstructure and improved ductility of the coatings. However, heat treatment at 950°C resulted in forming the Eta (η) phase and Ni-Ti intermetallics in all the NASA HR-1 cold spray coatings. Here, the overall results suggest that using He as process gas contributed to reduced porosity and enhanced mechanical properties of the cold spray coatings.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2018

Engineering Two-Phase and Three-Phase Microstructures from Water-Based Dispersions of Nanoparticles for Eco-Friendly Polymer Solar Cell Applications

Nanoparticle organic photovoltaics, a subfield of organic photovoltaics (OPV), has attracted increasing interest in recent years due to the eco-friendly fabrication of solar modules afforded by colloidal ink technology. Importantly, using this approach it is now possible to engineer the microstructure of the light absorbing/charge generating layer of organic photovoltaics; decoupling film morphology from film deposition. In this study, single-component nanoparticles of poly(3-hexylthiophene) (P3HT) and phenyl-C 61 butyric acid methyl ester (PC 61 BM) were synthesized and used to generate a two-phase microstructure with control over domain size prior to film deposition. Scanning transmission X-ray microscopy (STXM) and electron microscopy were used to characterize the thin film morphology. Uniquely, the measured microstructure was a direct input for a nanoscopic kinetic Monte Carlo (KMC) model allowing us to assess exciton transport properties that are experimentally inaccessible in these single-component particles. Photoluminescence, UV-vis spectroscopy measurements, and KMC results of the nanoparticle thin films enabled the calculation of an experimental exciton dissociation efficiency (η ED ) of 37% for the two-phase microstructure. The glass transition temperature (T g ) of the materials was characterized with dynamic mechanical thermal analysis (DMTA) and thermal annealing led to an increase in ηED to 64% due to an increase in donor-acceptor interfaces in the thin film from both sintering of neighboring opposite-type particles in addition to the generation of a third mixed phase from diffusion of PC 61 BM into amorphous P3HT domains. Finally, this study demonstrates the higher level of control over donor-acceptor film morphology enabled by customizing nanoparticulate colloidal inks, where the optimal three-phase film morphology for an OPV photoactive layer can be designed and engineered.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Modeling Framework to Predict Melting Dynamics at Microstructural Defects in TNT-HMX High Explosive Composites

Many high explosive (HE) formulations are composite materials whose microstructure is understood to impact functional characteristics. Interfaces are known to mediate the formation of hot spots that control their safety and initiation. Here, to study such processes at molecular scales, we developed all-atom force fields (FFs) for Octol, a prototypical HE formulation comprised of TNT (2,4,6-trinitrotoluene) and HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine). We extended a FF for TNT and recasted it in a form that can be readily combined with a well-established FF for HMX. The resulting FF was extensively validated against experimental results and density functional theory calculations. We applied the new combined TNT-HMX FF to predict and rank surface and interface energies, which indicate that there is an energetic driver for coarsening of microstructural grains in TNT-HMX composites. Finally, we assess the impact of several microstructural environments on the dynamic melting of TNT crystal under ultrafast thermal loading. We find that both free surfaces and planar material interfaces are effective nucleation points for TNT melting. However, MD simulations show that TNT crystal is prone to superheating by at least 50 K on subnanosecond time scales and that the degree of superheating is inversely correlated with surface and interface energy. The modeling framework presented here will enable future studies on hot spot formation processes in accident scenarios that are governed by strong coupling between microstructural interfaces, material mechanics, momentum and energy transport, phase transitions, and chemistry.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Reversible Binding Interfaces Made of Microstructured Polymer Brushes

The polymer brush architecture of the end-tethered polymer molecules is one of the most widely used efficient methods to regulate interfacial interactions in colloidal systems found in live matter and manufactured materials. Emerging applications of polymer brush structures require solutions to new tasks in the control of interfacial interactions. The rapid development of live cell manufacturing relies on scalable and efficient cell harvesting methods. Stimuli-responsive surfaces made of surface-grafted poly(N-isopropylacrylamide) (PNIPAM) can bind and detach the adherent cell upon changes in temperature and have been used for cell growth and harvesting. The applications are limited by the requirement to satisfy a range of PNIPAM coating characteristics that depend on the dimensions of the integrin complex in the cell membrane and the basal surface. The analysis of the microstructured surfaces, when adhesive and disjoining functions of the microdomains are decoupled, shows that many limitations of PNIPAM one-component coatings can be avoided by using a much broader range of structural characteristics of the microstructured interfaces composed of alternating disjoining PNIPAM domains and adhesive polymeric domains with cell-affinity functional groups. Temperature-controlled reversible adhesion to such microstructured interfaces is studied here experimentally with model systems of solid spherical particles and by employing simulations for solid and soft membranes interacting with the microstructured surfaces to mimic interactions with soft and solid disk-like particles.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Direct Ab Initio Simulation of the Synthesis of BaZrO 3 and the Microstructure Impacts on Proton Transport

Controlling and predicting the processing-structure-performance relationship in functional materials is a grand challenge in materials science, with important implications for a wide range of emerging applications; a high fidelity understanding of the performance impact of microstructures formed under synthesis conditions is required to develop advanced materials, such as solid-state fuel cells and electrolyzers. Using the ceramic BaZrO 3 as a case study, we directly simulate the synthesis and investigate how proton transport is dictated by microstructures. We develop a framework that couples density functional theory (DFT), machine-learning interatomic potential (MLIP) driven molecular dynamics, and grand canonical Monte Carlo to perform large-scale, microstructure-resolved, atomistic simulations of proton transport in experimentally representative polycrystalline structures. Our fully ab initio approach, using a MLIP as a proxy for DFT, allows us to quantify the competition between two distinct diffusion mechanisms: one associated with grain-boundary regions and another within grains. When the impacts of grain boundaries are taken into account, proton transport exhibits substantial deviation from the bulk oxide limit. This addresses long-standing discrepancies between theory and experiments. Our integrated approach provides atomistic insight into microstructure-dependent proton pathways in BaZrO 3 and establishes a general protocol for predicting processing-structure-performance relationships.

organic↗
DOE OSTI2025

A quantitative comparison of the fingerprint of twinned microstructures through surface and three-dimensional techniques

Assessing the fingerprint of a material’s microstructure is key for supporting materials design. With the emergence of a wide range of 3D characterization techniques, it is critical to understand the main differences in fingerprints reconstructed from 2D and 3D datasets. To this end, we introduce a graph-based microstructure reconstruction framework that enables structural comparisons of twin domain networks in high purity Ti using 3D and 2D electron backscatter diffraction. Insights into the structure of the twin networks are facilitated by combining statistical analysis of twin crystallography with visual and graphical analysis of the novel graph abstractions of the twins. We demonstrate that compared to 3D reconstructions, conventional 2D views of twinning miss key aspects of the microstructure including the high interconnectivity of domains into networks that span the full reconstruction volume. The reduced cross-grain and in-grain twin connectivity typically observed in 2D has notable implications on our understanding of how twinning mediates the plastic response of microstructures and how twin networks evolve. It is thus clear that 3D characterization is critical for accurately inferring both twin network morphologies as well as the key unit processes facilitating network formation.

36 MATERIALS SCIENCE↗
DOE OSTI2019

High-throughput 3D reconstruction of stochastic heterogeneous microstructures in energy storage materials

Abstract Stochastic heterogeneous microstructures are widely applied in structural and functional materials, playing a crucial role in determining their performance. X-ray tomography and focused ion beam serial sectioning are frequently used methods to reconstruct three-dimensional (3D) microstructures, yet are demanding techniques and are resolution-limited. Here, a high-throughput multi-stage 3D reconstruction method via distance correlation functions is developed using a single representatively large-sized 2D micrograph for stochastic microstructures, and verified by X-ray micro-tomography datasets of isotropic and anisotropic solid oxide fuel cell electrodes. This method provides an economic, easy-to-use and high-throughput approach for reconstructing stochastic heterogeneous microstructures for energy conversion and storage devices, and can readily be extended to other materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

An AI-driven microstructure optimization framework for elastic properties of titanium beyond cubic crystal systems

Materials design aims to identify the material features that provide optimal properties for various engineering applications, such as aerospace, automotive, and naval. One of the important but challenging problems for materials design is to discover multiple polycrystalline microstructures with optimal properties. This paper proposes an end-to-end artificial intelligence (AI)-driven microstructure optimization framework for elastic properties of materials. In this work, the microstructure is represented by the Orientation Distribution Function (ODF) that determines the volume densities of crystallographic orientations. The framework was evaluated on two crystal systems, cubic and hexagonal, for Titanium (Ti) in Joint Automated Repository for Various Integrated Simulations (JARVIS) database and is expected to be widely applicable for materials with multiple crystal systems. The proposed framework can discover multiple polycrystalline microstructures without compromising the optimal property values and saving significant computational time.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effect of decades of corrosion on the microstructure of altered glasses and their radiation stability

Understanding the microstructural evolution of glasses during their interaction with water and radiation is of fundamental importance in addressing the corrosion of nuclear waste forms under geological disposal conditions. Here we report the results of more than 21 years of corrosion of two borosilicate glasses showing the formation of mesoporous C–S–H gels in Ca-bearing glasses and a mainly microporous microstructure in Al-bearing glasses. These porous corroded glasses were then irradiated with heavy ions to simulate the effects of recoil nucleus damage and monitored in real time using transmission electron microscopy with in situ ion irradiation. The ballistic collisions remarkably healed the porous corroded glasses to a pore-free homogeneous microstructure. Besides providing new insights and predictions about how doped glasses and actual waste forms may evolve under corrosion and irradiation, the results highlight the non-universal nature of the existing corrosion models and the important role that the glass composition and radiation damage play in the evolution of the microstructure during corrosion.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multi-modal Dataset of a Polycrystalline Metallic Material: 3D Microstructure and Deformation Fields

The development of high-fidelity mechanical property prediction models for the design of polycrystalline materials relies on large volumes of microstructural feature data. Concurrently, at these same scales, the deformation fields that develop during mechanical loading can be highly heterogeneous. Spatially correlated measurements of 3D microstructure and the ensuing deformation fields at the micro-scale would provide highly valuable insight into the relationship between microstructure and macroscopic mechanical response. They would also provide direct validation for numerical simulations that can guide and speed up the design of new materials and microstructures. However, to date, such data have been rare. Here, a one-of-a-kind, multi-modal dataset is presented that combines recent state-of-the-art experimental developments in 3D tomography and high-resolution deformation field measurements.

36 MATERIALS SCIENCE↗