Search NASA⌕ Search

SEARCH · Search NASA

Results for “nanocrystalline”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Investigation of kinetic inductance and microwave loss in thin-film TaC x N 1−x superconducting resonators

The promise of tantalum for realizing superconducting quantum devices has generated interest in its compound films, particularly nitrides. Among these, cubic-phase tantalum carbonitride (TaC x N 1−x ) offers reduced susceptibility to oxidation and a high critical temperature, yet its microwave properties remain largely unexplored. Here, in this study, we investigate plasma-enhanced atomic layer deposition of cubic-phase TaC x N 1−x thin films for superconducting microwave circuits. Structural and transport measurements reveal nanocrystalline morphology with sub-10 nm grains and superconductivity in the dirty limit. Coplanar waveguide resonators exhibit moderately high kinetic inductance (16.8 pH/sq for 30 nm films) with potential for enhancement through dimensional scaling. The films also support high internal quality factors exceeding 10 5 at 50 mK in the single-photon regime, comparable to granular aluminum. Loss analysis identifies the two-level systems as the dominant limiting mechanism, with potential for further reduction through interface engineering. These results establish atomic layer deposited TaC x N 1−x as a promising material for scalable, low-loss, high-inductance superconducting circuits.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Reduced thermal resistance of Al-rich AlGaN HEMTs via top-side diamond integration

We report back-end-of-line growth of nanocrystalline diamond (NCD) on ultrawide bandgap (UWBG) high Al content aluminum gallium nitride (AlGaN) channel high electron mobility transistors for thermal management. A thin (∼15 nm) silicon nitride (SiN x ) interlayer was deposited to protect the device surface before performing a low temperature (500 °C) NCD growth process in an attempt to protect the gates on these fully fabricated devices. Notably, atomic force microscopy showed that the maximum lateral grain size exceeded 300 nm even though the film thickness was ∼250 nm. Comparing electrical (DC) performance before and after NCD growth, the gate leakage increased by ∼10 2 after NCD growth. Despite the lower NCD growth temperature, intermixing of the Ni and Au was observed in the Schottky gate metal stack; however, we believe there is another mechanism, possibly hydrogen-related, that is responsible for the measured increase in gate leakage. Regarding thermal management, the device-level thermal resistance (quantified using the average gate temperature rise measured by thermoreflectance imaging) was reduced by 29% through the incorporation of the top-side diamond film. Using time-domain thermoreflectance, the thermal conductivity of the ≈250 nm thick NCD film was measured to be 45 ± 25 W m −1 K −1 . This is expected to be at least 5× greater than the thermal conductivity of the thin disordered AlGaN alloy. There could also be a coupled electrothermal component contributing to the reduced temperature rise from electric field spreading and consequent heat spreading. This study demonstrates a promising first step toward device-level thermal management of high power UWBG Al-rich AlGaN devices.

Lundh, James Spencer [U.S. Naval Research Laborato↗
DOE OSTI2026

Influence of minor Ce additions on magnetic and electrical properties in Fe–6.5 wt. % Si alloy

Fe–6.5 wt. % Si alloys exhibit lower core loss at higher frequency than the dominating electrical steel containing 3.2% Si due to its lower magneto-crystalline anisotropy energy (MAE) and higher electrical resistivity. However, compared to nanocrystalline and amorphous soft-magnetic materials, 6.5% Si steel, although being cost effective and having high saturation magnetization, still has much to improve, especially with respect to MAE and resistivity. To explore further improvement, the effects of minor Ce additions (due to its mixed valence 4f-electron configuration) on the microstructure, electrical and magnetic behaviors of Fe–6.5 wt. % Si alloys were investigated. Due to its limited solubility in Fe, Ce exhibits condition-dependent effects on electrical resistivity, showing only marginal improvement under rapid solidification. In contrast, Ce addition degrades magnetic performance, reducing saturation magnetization (from 1.86 to 1.76 T) and increasing coercivity (from 88 to 171 A/m), which results in an 83.4% increase in core loss (W 10/1000 condition). Overall, Ce addition provides limited benefit in electrical resistivity while deteriorating magnetic properties, making it ineffective for enhancing the soft magnetic performance of Fe–6.5 wt. % Si alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Diagenetic formation of uranium-silica polymers in lake sediments over 3,300 years

Significance Understanding the long-term fate of widespread noncrystalline uranium (U) species is critical to improving our knowledge of U biogeochemistry and U-contaminated environments. We use naturally U-enriched lake sediments that have been deposited for thousands of years as an analogue for the progressive evolution of contaminated environments, in order to uncover if noncrystalline species may evolve into more resistant crystalline phases. We combine multidisciplinary tools including U isotope ratio and speciation techniques to describe a mineralogical transformation where organic-bound U evolves into polymeric and nanocrystalline uranium-silica phases that are still easily remobilized even 3,300 y after their deposition. These findings bring an interpretation that illuminates an active debate on uranium mobility in the environment.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2023

Shewanella oneidensis MR-1 respires CdSe quantum dots for photocatalytic hydrogen evolution

Living bio-nano systems for artificial photosynthesis are of growing interest. Typically, these systems use photoinduced charge transfer to provide electrons for microbial metabolic processes, yielding a biosynthetic solar fuel. Here, we demonstrate an entirely different approach to constructing a living bio-nano system, in which electrogenic bacteria respire semiconductor nanoparticles to support nanoparticle photocatalysis. Semiconductor nanocrystals are highly active and robust photocatalysts for hydrogen (H 2 ) evolution, but their use is hindered by the oxidative side of the reaction. In this system, Shewanella oneidensis MR-1 provides electrons to a CdSe nanocrystalline photocatalyst, enabling visible light-driven H 2 production. Unlike microbial electrolysis cells, this system requires no external potential. Illuminating this system at 530 nm yields continuous H 2 generation for 168 h, which can be lengthened further by replenishing bacterial nutrients.

Science & Technology - Other Topics↗
DOE OSTI2024

Viral afterlife: SARS-CoV-2 as a reservoir of immunomimetic peptides that reassemble into proinflammatory supramolecular complexes

It is unclear how severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) infection leads to the strong but ineffective inflammatory response that characterizes severe Coronavirus disease 2019 (COVID-19), with amplified immune activation in diverse cell types, including cells without angiotensin-converting enzyme 2 receptors necessary for infection. Proteolytic degradation of SARS-CoV-2 virions is a milestone in host viral clearance, but the impact of remnant viral peptide fragments from high viral loads is not known. Here, we examine the inflammatory capacity of fragmented viral components from the perspective of supramolecular self-organization in the infected host environment. Interestingly, a machine learning analysis to SARS-CoV-2 proteome reveals sequence motifs that mimic host antimicrobial peptides (xenoAMPs), especially highly cationic human cathelicidin LL-37 capable of augmenting inflammation. Such xenoAMPs are strongly enriched in SARS-CoV-2 relative to low-pathogenicity coronaviruses. Moreover, xenoAMPs from SARS-CoV-2 but not low-pathogenicity homologs assemble double-stranded RNA (dsRNA) into nanocrystalline complexes with lattice constants commensurate with the steric size of Toll-like receptor (TLR)-3 and therefore capable of multivalent binding. Such complexes amplify cytokine secretion in diverse uninfected cell types in culture (epithelial cells, endothelial cells, keratinocytes, monocytes, and macrophages), similar to cathelicidin’s role in rheumatoid arthritis and lupus. The induced transcriptome matches well with the global gene expression pattern in COVID-19, despite using <0.3% of the viral proteome. Delivery of these complexes to uninfected mice boosts plasma interleukin-6 and CXCL1 levels as observed in COVID-19 patients.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Bragg Coherent Imaging of Fluctuating Domains

This review presents two examples of domain dynamics in crystalline solid state samples which were imaged recently with synchrotron X-rays by Bragg Coherent Diffraction methods. Domains are associated with sub-atomic phase shifts in the structure which are revealed by the strong phase contrast associated with Bragg diffraction. At low temperatures, La2-xSrxNiO4 has an antiferromagnetic spin-ordered phase with correlation lengths of 200 nm; its domains are imaged with magnetic Bragg Ptychography to visualize their slow fluctuations. Hydrothermally synthesized nanocrystalline BaTiO3 is found to be made up of ~50 nm domains using Bragg Coherent Diffraction Imaging; electric field induced movement of its internal domain walls is a likely explanation of the nano-material's anomalously large dielectric constant, which is used in the manufacture of multilayer ceramic capacitors

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Structure-property correlations and scaling in the magnetic and magnetocaloric properties of GdCrO 3 particles

The structure, magnetic, and magnetocaloric (MC) properties of orthorhombic nanocrystalline GdCrO 3 with six particle sizes: < d > = 87, 103, 145, 224, 318, and 352 nm are reported. The particle size was tailored by annealing under different temperatures and estimated by scanning electron microscopy. With increase in < d >, Goldschmidt tolerance factor t, orthorhombic strain s, and out-of-plane Cr–O 1 –Cr bond angle first decrease, reaching minimum values for < d > = 224 nm, and then increase for sample with < d > = 318 nm and 352 nm, thus showing a V-shaped variation. Temperature dependence of the magnetization (M) reveals an antiferromagnetic transition at ${T}_{\text{N}}^{\text{Cr}}\sim 168$ K for < d > ≥ 224 nm and ${T}_{\text{N}}^{\text{Cr}}\sim 167$ K for < d > < 224 nm and an essentially d-independent spin-reorientation at T SR = 9 K. M measured at 5 K and 7 T first increases with increase in < d >, reaching maximum value for sample with < d > = 224 nm, and then decreases for samples with < d > = 318 nm and 352 nm, showing an inverted-V variation with < d >. Similar < d >-dependence is observed for the magnetic entropy change (MEC) and relative cooling power (RCP) showing a close relationship between the structural and magnetic properties of GdCrO 3 nanoparticles investigated here. The 224 nm sample with the minimum values of t, s, and Cr–O 1 –Cr bond angle exhibits the maximum value of MEC (–ΔS) = 37.8 J kg –1 K –1 at 5 K under a field variation (ΔH) of 7 T and its large estimated RCP of 623.6 J Kg –1 is comparable with those of typical MC materials. Both (–ΔS) and RCP are shown to scale with the saturation magnetization MS, suggesting that MS is the crucial factor controlling their magnitudes. Assuming (–ΔS) ~ (ΔH) n , the temperature dependence of n for the six samples are determined, n varying between 1.3 at 5 K to n = 2.2 at 130 K in line with its expected magnitudes based on mean-field theory. Furthermore, these results on structure-property correlations and scaling in GdCrO 3 suggest that its MC properties are tunable for potential low-temperature magnetic refrigeration applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Simulating hindered grain boundary diffusion using the smoothed boundary method

Abstract Grain boundaries can greatly affect the transport properties of polycrystalline materials, particularly when the grain size approaches the nanoscale. While grain boundaries often enhance diffusion by providing a fast pathway for chemical transport, some material systems, such as those of solid oxide fuel cells and battery cathode particles, exhibit the opposite behavior, where grain boundaries act to hinder diffusion. To facilitate the study of systems with hindered grain boundary diffusion, we propose a model that utilizes the smoothed boundary method to simulate the dynamic concentration evolution in polycrystalline systems. The model employs domain parameters with diffuse interfaces to describe the grains, thereby enabling solutions with explicit consideration of their complex geometries. The intrinsic error arising from the diffuse interface approach employed in our proposed model is explored by comparing the results against a sharp interface model for a variety of parameter sets. Finally, two case studies are considered to demonstrate potential applications of the model. First, a nanocrystalline yttria-stabilized zirconia solid oxide fuel cell system is investigated, and the effective diffusivities are extracted from the simulation results and are compared to the values obtained through mean-field approximations. Second, the concentration evolution during lithiation of a polycrystalline battery cathode particle is simulated to demonstrate the method’s capability.

Materials Science↗
DOE OSTI2019

Optimized oxygen deprived low temperature sputtered WO3 thin films for crystalline structures

In this work, we report a detailed analysis on the effects of processing parameters for sputtered tungsten trioxide (WO 3 ) thin nanoscale films on their structural, vibrational and electrical properties. The research aims to understand the fundamental aspects of WO3 sputtering at relatively low temperatures and in an oxygen deprived environment targeting applications of temperature and oxygen sensitive substrates. Structural analysis indicates that films deposited at room temperature, or substrate temperatures at or below 400 degrees C with low oxygen partial pressure are amorphous. Furthermore, crystallization of the films was observed with distinct Raman peaks when the films were annealed at 300 degrees C or above using rapid thermal annealing for 10 min. Films revealed monoclinic phases of WO 3 with the presence of W-O-W stretching, bending and lattice vibrational modes in the Raman spectra. Interestingly, a change of transport behavior from insulating to semiconducting was observed for as deposited films on post annealing. Annealed films revealed stoichiometric WO 3 phases with no external defects detected. The present study adopts a route to intercalate WO 3 in a variety of applications from electrochromic coloration to a nanocrystalline thin film for electronic devices sensitive to higher temperatures and gas flow in the sputtering system.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Colossal grain growth in Cd(Se,Te) thin films and their subsequent use in CdTe epitaxy by close-spaced sublimation

Many technologies deposit thin films on inexpensive substrates, resulting in small grains due to classic nucleation and grain growth theory. For example, state-of-the-art solar cells are made by depositing CdSeTe and CdTe layers on inexpensive glass coated with nanocrystalline transparent conducting oxides (TCOs), like SnO 2 . Characteristically, the grain size of these films is on the order of the film thickness, i.e. a few microns. CdTe small-grain films have poor electro-optical properties and require CdCl 2 passivation which fails to fully passivate grain boundaries, causes carrier compensation, and prevents implementing other II–VI alloys and materials to improve performance. Here, we present a method to increase grain size to 1 mm in CdSe x Te 1-x thin films deposited on glass/TCO substrates without CdCl 2 treatment. The colossal grain growth is driven by mechanisms distinct from classic nucleation, grain growth, and Ostwald ripening and only occurs at low selenium content (x ~ 0.1). We also demonstrate how these films can serve as templates for subsequent large-grain epitaxy of other compositions like CdTe, again without exposure to CdCl 2 . The results open new paths for thin film solar cell technology, and thin film devices in general.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Effect on compression of lowering the design adiabat in the SQ-n campaign

A set of experiments in the SQ-n campaign attempts to increase the compression in layered implosions by reducing the design adiabat from 3.0 down to ∼ 2.6. The experiments utilize nanocrystalline high density carbon ablators driven by a ramped laser pulse drive. Contrary to expectations, the lower design adiabat layered implosion reaches the same level of compression, within the measurement uncertainty, as the previous set of SQ-n layered implosions at the higher design adiabat. Here, we examine potential explanations for this result, including incomplete melting or refreezing of the ablator after the first shock passes into the fuel layer, reproducibility, and dopant areal density. We also discuss additional potential paths to reaching lower adiabat including increased dopant areal density, ramped dopant profiles, and increased initial capsule size which are also based on experimental campaign results from the National Ignition Facility.

Physics - Plasma physics↗
DOE OSTI2019

Microstructure evolution during near- T g annealing and its effect on shear banding in model alloys

By performing extensive molecular dynamics simulations, we investigate herein the deformation behavior in A l 90 S m 10 and C u 64.5 Z r 35.5 alloys after elongated isothermal annealing in the vicinity of the glass-transition temperature ( T g ). Different microstructural response to the annealing process was observed: A l 90 S m 10 maintains the glassy structure with improved energetic stability, enhanced short-range order (SRO), and a more pronounced spatial network that extends beyond the first atomic shell, while C u 64.5 Z r 35.5 forms nanocrystalline Laves C u 2 Zr phases. Shear banding occurs in both annealed systems under shear loading. For A l 90 S m 10 , the spatial network formed by the local clusters characterizing the SRO of the system is significantly weakened but remains appreciable in the shear band. In contrast, the crystalline ordering in the C u 64.5 Z r 35.5 is completely destroyed during shear banding. Consequently, while displaying higher yield strength, the annealed C u 64.5 Z r 35.5 sample appears to be less ductile. By carefully examining the effect of microstructures on the structural ordering in the shear band and the consequent mechanical response, our work contributes to a better understanding of the deformation mechanism of amorphous alloys as compared with that in crystalline materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Synthesis of metallic glass nanoparticles by inert gas condensation

Inert Gas Condensation (IGC) is a versatile method for the synthesis of ultrafine nanoparticles. While it has been mostly used in the synthesis of nanocrystalline particles it has also been employed in the synthesis of metallic glass nanoparticles, which can be further used in the generation of nanostructured metallic glasses, known as nanoglasses. In this work, we use molecular dynamics simulations to investigate the IGC processes leading to the synthesis of Cu 64 Zr 36 amorphous nanoparticles. We investigate the growth of nanoparticles up to 7.3 nm diameter using long simulations of up to 130 ns, under relatively low pressures in the range of 4 to 10 bars. Results indicate a significant effect of pressure on the final structure of the amorphous nanoparticles, yet no clear influence on the segregation of Cu atoms to its surface. Cu segregation occurring at all pressures results in a thin Cu rich layer, about 2.5 Å thick, that coats all nanoparticles. Here, statistics of atomic Voronoi polyhedra shows that the fraction of full icosahedra in the nanoparticles produced at 4 bars is equivalent to that of bulk metallic glasses produced by melt and quench at 10 9 K/s. Higher pressures result in a lower fraction of full icosahedra.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Size-dependent attraction of Cu solutes to clusters formed at Ag grain boundaries

We report a size-dependent solute clustering mechanism at grain boundaries in a sputtered ultrafine-grained Ag-Cu alloy, where large Cu clusters form despite weak individual solute-solute interactions. X-ray diffraction confirms limited Cu solubility in the Ag matrix, while scanning transmission electron microscopy reveals Cu clustering at both ordinary GBs and GB junctions. Density functional theory calculations show that 12-atom Cu clusters are energetically preferred, while smaller three-atom clusters are significantly less stable. Additional calculations demonstrate a marked increase in solute-cluster attraction energy with cluster size. As a result, these findings point to a previously unrecognized pathway for grain-boundary solute clustering in immiscible systems, driven by collective solute-cluster interactions, with implications for segregation behavior and stability in nanocrystalline and ultrafine-grained alloys.

Alloys↗
DOE OSTI2021

Removal of spurious data in Bragg coherent diffraction imaging: an algorithm for automated data preprocessing

Bragg coherent diffraction imaging (BCDI) provides a powerful tool for obtaining high-resolution structural information from nanocrystalline materials. Here a BCDI sample consisting of a large number of randomly oriented nanoscale crystals is considered. Ideally, only one crystal is oriented to produce a Bragg peak on the detector. However, diffraction from other crystals often produces additional signals on the detector. Before the measured diffraction patterns can be processed into structural images, scientists routinely need to manually identify and remove the `alien' intensities from sources other than the intended crystal. With the development of modern high-coherence storage rings, such as the upgraded Advanced Photon Source (APS), the already slow process of manual preprocessing will be untenable for the large volumes of data that will be produced. An automated method of identifying and deleting alien intensities is proposed. This method exploits the fact that BCDI of a perfect crystal produces diffraction data with inversion symmetry around the Bragg peak. This approach uses the machine learning clustering method DBSCAN to distinguish between diffraction from multiple sources, and then calculates cluster size and inversion symmetry to assess whether clusters of intensity belong to desired data or alien signals. This approach can dramatically reduce the amount of time spent manually processing data, allowing BCDI data processing capabilities to keep pace with the technological advances of fourth-generation synchrotron light sources.

36 MATERIALS SCIENCE↗
DOE OSTI2023

True molecular conformation and structure determination by three-dimensional electron diffraction of PAH by-products potentially useful for electronic applications

The true mol­ecular conformation and the crystal structure of benzo[e]di­naphtho­[2,3-a;1',2',3',4'-ghi]fluoranthene, 7,14-di­phenyl­naphtho­[1,2,3,4-cde]bis­anthene and 7,16-di­phenyl­naphtho­[1,2,3,4-cde]heli­anthrene were determined ab initio by 3D electron diffraction. All three mol­ecules are remarkable polycyclic aromatic hydro­carbons. The mol­ecular conformation of two of these com­pounds could not be determined via classical spectroscopic methods due to the large size of the mol­ecule and the occurrence of multiple and reciprocally connected aromatic rings. The mol­ecular structure of the third mol­ecule was previously considered provisional. These com­pounds were isolated as by-products in the synthesis of similar products and were at the same time nanocrystalline and available only in very limited amounts. 3D electron diffraction data, taken from submicrometric single crystals, allowed for direct ab initio structure solution and the unbiased determination of the inter­nal mol­ecular conformation. Detailed synthetic routes and spectroscopic analyses are also discussed. Based on many-body perturbation theory simulations, benzo[e]di­naphtho­[2,3-a;1',2',3',4'-ghi]fluoranthene may be a promising candidate for triplet–triplet annihilation and 7,14-di­phenyl­naphtho­[1,2,3,4-cde]bis­anthene may be a promising candidate for inter­molecular singlet fission in the solid state.

36 MATERIALS SCIENCE↗