Search NASA⌕ Search

SEARCH · Search NASA

Results for “polynomials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Nonlinear temperature dependent failure analysis of finite width composite laminates

A quasi-three dimensional, nonlinear elastic finite element stress analysis of finite width composite laminates including curing stresses is presented. Cross-ply, angle-ply, and two quasi-isotropic graphite/epoxy laminates are studied. Curing stresses are calculated using temperature dependent elastic properties that are input as percent retention curves, and stresses due to mechanical loading in the form of an axial strain are calculated using tangent modulii obtained by Ramberg-Osgood parameters. It is shown that curing stresses and stresses due to tensile loading are significant as edge effects in all types of laminate studies. The tensor polynomial failure criterion is used to predict the initiation of failure. The mode of failure is predicted by examining individual stress contributions to the tensor polynomial.

Nagarkar, A. P.↗
NASA NTRS1979

Recurrence relations for computing with modified divided differences

Modified divided differences (MDD) provide a good way of representing a polynomial passing through points with unequally spaced abscissas. This note gives recurrence relations for computing coefficients in either the monomial or Chebyshev basis from the MDD coefficients, and for computing the MDD coefficients for either the differentiated or the integrated polynomial. The latter operation is likely to be useful if MDD are used in a method for solving stiff differential equations.

Krogh, F. T.↗
NASA NTRS1980

An analytical technique for approximating unsteady aerodynamics in the time domain

An analytical technique is presented for approximating unsteady aerodynamic forces in the time domain. The order of elements of a matrix Pade approximation was postulated, and the resulting polynomial coefficients were determined through a combination of least squares estimates for the numerator coefficients and a constrained gradient search for the denominator coefficients which insures stable approximating functions. The number of differential equations required to represent the aerodynamic forces to a given accuracy tends to be smaller than that employed in certain existing techniques where the denominator coefficients are chosen a priori. Results are shown for an aeroelastic, cantilevered, semispan wing which indicate a good fit to the aerodynamic forces for oscillatory motion can be achieved with a matrix Pade approximation having fourth order numerator and second order denominator polynomials.

Dunn, H. J.↗
NASA NTRS1979

The generalized pole assignment problem

For some linear, strictly proper system given by its transfer function, two dynamic output feedback problems can be posed. The first one is that of using dynamic-output feedback to assign the closed-loop characteristic polynomial and the second that of assigning the closed-loop invariant factors. These problems and their interrelationships are discussed. The formulation is done in the frequency domain and the investigation carried out from an algebraic point of view, in terms of linear equations over rings of polynomials. Using the notion of genericity, several necessary and sufficient conditions are expressed.

Djaferis, T. E.↗
NASA NTRS1981

Heat transfer of phase-change materials in two-dimensional cylindrical coordinates

Two-dimensional phase-change problem is numerically solved in cylindrical coordinates (r and z) by utilizing two Taylor series expansions for the temperature distributions in the neighborhood of the interface location. These two expansions form two polynomials in r and z directions. For the regions sufficiently away from the interface the temperature field equations are numerically solved in the usual way and the results are coupled with the polynomials. The main advantages of this efficient approach include ability to accept arbitrarily time dependent boundary conditions of all types and arbitrarily specified initial temperature distributions. A modified approach using a single Taylor series expansion in two variables is also suggested.

Labdon, M. B.↗
NASA NTRS1980

Geometrical rectification of spin-scan images from Pioneer 11

Images of Saturn received from Pioneer 11 suffer from geometrical distortions due to the curvilinear scan lines and the unequal sampling intervals in orthogonal directions, which are inherent in spin-scan imaging. In this paper geometrical image rectification by polynomial transformation based on control points is discussed. Factors that affect the accuracy of reconstruction are shown to include the spatial distribution and spatial density of control points, and the order of the polynomial distortion model. A computer implementation of the technique is described.

Strickland, R. N.↗
NASA NTRS1980

Alignment and evaluation of the cryogenic corrected infrared astronomical satellite /IRAS/ telescope

Room temperature alignment and evaluation techniques for the Infrared Astronomical Satellite (IRAS) telescope, which has a primary mirror figured to correct for surface distortions and the 2 K operating temperature are discussed. Interferometric cryogenic testing of the 0.6 m, f/1.5 lightweighted beryllium primary mirror at its intended operating temperature reveals surface distortions that can be modeled with Zernike polynomials. With this model, it becomes possible to derive the 'inverse' of the cryowavefront error (ideal cryo mirror) and to figure the cryo correction into the primary mirror using Perkin-Elmer's Computer Controlled Polisher. It is recognized that during room temperature assembly of the system, misalignment of the secondary mirror can introduce additional unwanted aberrations that may cancel or distort the wavefront errors purposely introduced by the cryo figuring. To avoid this possible degradation and to ensure optimum telescope performance, the system Zernike polynomial coefficients and wavefront maps generated from the in-process alignment interferograms are monitored and compared to Zernike coefficients and wavefront maps for the cryo corrected primary mirror.

Harned, N.↗
NASA NTRS1982

Tolerance analysis of optical telescopes using coherent addition of wavefront errors

A near diffraction-limited telescope requires that tolerance analysis be done on the basis of system wavefront error. One method of analyzing the wavefront error is to represent the wavefront error function in terms of its Zernike polynomial expansion. A Ramsey-Korsch ray trace package, a computer program that simulates the tracing of rays through an optical telescope system, was expanded to include the Zernike polynomial expansion up through the fifth-order spherical term. An option to determine a 3 dimensional plot of the wavefront error function was also included in the Ramsey-Korsch package. Several assimulation runs were analyzed to determine the particular set of coefficients in the Zernike expansion that are effected by various errors such as tilt, decenter and despace. A 3 dimensional plot of each error up through the fifth-order spherical term was also included in the study. Tolerance analysis data are presented.

Davenport, J. W.↗
NASA NTRS1983

VLSI Unit for Two-Dimensional Convolutions

Universal logic structure allows same VLSI chip to be used for variety of computational functions required for two dimensional convolutions. Fast polynomial transform technique is extended into tree computational structure composed of two units: fast polynomial transform (FPT) unit and Chinese remainder theorem (CRT) computational unit.

Liu, K. Y.↗
NASA NTRS1982

Investigation of Antarctic crust and upper mantle using MAGSAT and other geophysical data

Antarctica is the perfect proving ground for testing data reduction procedures which are alternatives to the standard procedure employing polynomial fitting. Unreduced data (observed values minus corefield model theo each pass) were averaged in 3 degree bins. The resulting map was then high pass filtered using a finite Fourier transform filter so that spectral peaks between 4200 km and 5280 km were diminished by 1/3, peaks corresponding to wavelengths greater than or equal to 5280 km were diminished by 1/2, and the d.c. component was set equal to zero. The surface subtracted in this way differs from the polynomials used in the standard method in that it is static over the 5 north data window. The map produced is presented and the effects of the static model are compared to those of the dynamic mode.

Bentley, C. R.↗
NASA NTRS1983

Simplified Syndrome Decoding of (n, 1) Convolutional Codes

A new syndrome decoding algorithm for the (n, 1) convolutional codes (CC) that is different and simpler than the previous syndrome decoding algorithm of Schalkwijk and Vinck is presented. The new algorithm uses the general solution of the polynomial linear Diophantine equation for the error polynomial vector E(D). This set of Diophantine solutions is a coset of the CC space. A recursive or Viterbi-like algorithm is developed to find the minimum weight error vector cirumflex E(D) in this error coset. An example illustrating the new decoding algorithm is given for the binary nonsymmetric (2,1)CC.

I. S. Reed↗
NASA NTRS1983

New syndrome decoder for (n, 1) convolutional codes

The letter presents a new syndrome decoding algorithm for the (n, 1) convolutional codes (CC) that is different and simpler than the previous syndrome decoding algorithm of Schalkwijk and Vinck. The new technique uses the general solution of the polynomial linear Diophantine equation for the error polynomial vector E(D). A recursive, Viterbi-like, algorithm is developed to find the minimum weight error vector E(D). An example is given for the binary nonsystematic (2, 1) CC.

Reed, I. S.↗
NASA NTRS1982

Modelling of TGS growth in space

Attention is called to the necessity of programming the temperature downward in order to maintain a constant growth rate in the absence of convection. Trial and error numerical computations are performed to find the first approximation for the required isothermal dissolution period, linear ramp, and polynomial temperature variation period. The linear ramp rate is limited by the specified maximum temperature gradient. The isothermal dissolution turns out to be unnecessary. The linear ramp must be stopped before the polynomial period is begun in order to avoid overshooting the specified maximum growth rate. After a few hours, the temperature profile approaches steady-state behavior.

Liu, L. C.↗
NASA NTRS1984

MAGSAT correlations with geoid anomalies

A digital data library of MAGSAT data is described and its applications and capabilities are reviewed. Polynomial trends were removed from each half-orbit in order to estimate and remove ring current effects from the data. The MAGSAT data in the Gulf of Mexico region was analyzed to define better the possible relation of the negative MAGSAT anomaly there to the negative residual geoid anomaly in the western Gulf of Mexico. Since the shape and location of the negative magnetic anomaly are variable depending upon the particular polynomial surface and curve orders used, no definitive conclusion as to the degree of correspondance between the residual geoid and MAGSAT lithosphere anomalies is offered.

Bowin, C. O.↗
NASA NTRS1983

Radar image registration and rectification

Two techniques for radar image registration and rectification are presented. In the registration method, a general 2-D polynomial transform is defined to accomplish the geometric mapping from one image into the other. The degree and coefficients of the polynomial are obtained using an a priori found tiepoint data set. In the second part of the paper, a rectification procedure is developed that models the distortion present in the radar image in terms of the radar sensor's platform parameters and the topographic variations of the imaged scene. This model, the ephemeris data and the digital topographic data are then used in rectifying the radar image. The two techniques are then used in registering and rectifying two examples of radar imagery. Each method is discussed as to its benefits, shortcomings and registration accuracy.

Naraghi, M.↗
NASA NTRS1984

Failure analysis for composite laminates

A discussion of the tensor polynomial failure criterion is presented together with a description of a biaxial compression test procedure used in the evaluation of the interaction strength parameters. In addition, a formulation for predicting the fatigue life of laminates is given based on the experimental evaluation of fatigue functions which are also utilized in a form of the tensor polynomial failure criterion as well. Experimental results are provided to compare with the fatigue life predictions and to demonstrate the effect of flaws and environment. Both bond-line defects in sandwich beam construction and inter-laminar disbond flaws are studied. Up to present, compressive strength test data have been obtained for ambient and elevated temperature, moisture-saturated conditions, including results from thermal-spike cycling simulating supersonic flight.

Tennyson, R. C.↗
NASA NTRS1984

Non-nulling seven-hole probes for high angle flow measurement

This paper illustrates a method for calibrating seven-hole probes to measure local total and static pressures and relative flow angles of up to 70 degrees in subsonic compressible flows. The method of Latin Squares was used to statistically sample a large and otherwise unmanageable data set, thereby reducing to a minimum the number of data points required to construct a polynomial curve fit to the data. Calibration produces three-variable third order polynomials which permit all of the desired flow properties to be found explicitly from probe measured pressures. This method determines the flow angles to within 2 degrees and Mach number to within 0.04 with 95 percent certainty.

Gerner, A. A.↗
NASA NTRS1984

Performance of the h, p and h-p versions

There are three basic versions of the finite element method, called the h, p and h-p versions. They are characterized by the way in which the finite element meshes and polynomial degree of elements are chosen. They differ in computer implementation (program architecture) and mathematical analysis. The manner in which the meshes and polynomial degree of the elements affect the accuracy of finite element solutions is examined. The approach is to fix certain parameters and increase the number of degrees of freedom so that the finie element solutions converge to the exact solution. Such a systematic increase of the number of degrees of freedom is called extension because it can be interpreted as a systematic extension of finite element spaces.

Babuska, I.↗