Search NASA⌕ Search

SEARCH · Search NASA

Results for “positional dependence”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Satellite interferometer as an advanced navigation/communication system

An orthogonal system of interferometry baselines aboard a geostationary satellite is proposed to be used for navigation, surveillance, and traffic control. Position determination is based on the relationship between the measured phase differences, the known and unknown transmitter locations, and other systematic error model parameters using a generalized least-squares estimation procedure. It is shown that position accuracy is critically dependent on the baseline length and on the magnitude of the random component of the measuring errors. Several trade-offs with respect to the system accuracies, the number of users, data rates, hardware costs, etc., are examined. Simultaneous use of the same channels for navigation and data transfer is found feasible and five candidate or 'strawman' interferometer system proposals are presented. It is concluded that the system's performance is excellent in comparison with present or planned systems, and that it is viable in meeting potential user's requirements.

Gopalapillai, G. S.↗
NASA NTRS1981

Experimental investigation of the flow on the suction side of a thin Delta wing

Surface oil flow patterns were photographed and pressure distribution measurements were carried out on a sharp edged delta wing of aspect ratio lambda = 1.0 in order to determine the influence of Reynolds number and of vortex breakdown on the flow on the suction side of the wing. The formation of the secondary vortex occurs due to separation of a laminar boundary layer in the front part of the wing and due to separation of a turbulent boundary layer in the rear part of the wing. In the case of turbulent separation, the secondary separation line is closer to the wing leading edge than in the laminar case. The position of the transition depends on the Reynolds number and on the angle of incidence. The breakdown of a vortex above the wing leads to a kink in the secondary separation line.

Hummel, D.↗
NASA NTRS1984

Cosmic ray exposure ages of iron meteorites, complex irradiation and the constancy of cosmic ray flux in the past

While previous calculations of potassium ages assumed a constant cosmic ray flux and a single stage (no change in size) exposure of iron meteorites, present calculations relaxed these constancy assumptions and the results reveal multistage irradiations for some 25% of the meteorites studied, implying multiple breakup in space. The distribution of exposure ages suggests several major collisions (based on chemical composition and structure), although the calibration of age scales is not yet complete. It is concluded that shielding-corrected (corrections which depend on size and position of sample) production rates are consistent for the age bracket of 300 to 900 years. These production rates differ in a systematic way from those calculated for present day fluxes of cosmic rays (such as obtained for the last few million years).

Marti, K.↗
NASA NTRS1983

Deposition of silicon nitride from SiCl4 and NH3 in a low pressure RF plasma

Silicon nitride coatings were deposited in a low-pressure (1-10 Torr) RF plasma from SiCl4 and NH3 in the presence of argon onto stainless martensitic steel grounded and floating substrates at 300 C and 440 C respectively. The heating of the substrates depends mainly on the position and the induced RF power. The coatings were identified as silicon nitride by X-ray investigation and were found to contain chlorine by energy-dispersive analysis of X-rays. The growth rate, the microhardness and the chlorine concentration of the coatings were determined as a function of the total gas pressure, the RF power input and the NH3-to-SiCl4 ratio. It was observed that the coatings on the floating substrates have higher deposition rates and are of superior quality.

Ron, Y.↗
NASA NTRS1989

Unsteady stagnation-point heat transfer during passage of a concentrated vortex

The unsteady boundary layer due to a single rectilinear vortex filament approaching a 2-D stagnation point is investigated. Assuming the vortex remains far from the surface, incompressible potential flow theory is used to determine the time dependent inviscid flow field. The unsteady boundary layer equations are solved by an alternating-direction-implicit finite-difference method. Two mechanisms which cause fluctuations in heat transfer are the unsteady velocity field in the boundary layer and secondly, the unsteady total temperature at the edge of the boundary layer. The relative importance of these mechanisms is dependent upon the total temperature fluctuations relative to the imposed temperature difference. As a vortex approaches a stagnation point it may be forced to one side of the stagnation line or the other, depending on its initial position. Results are presented for both of these cases.

Rigby, David L.↗
NASA NTRS1988

A study of cloud-generated radiative heating and its generation of available potential energy. I - Theoretical background. II - Results for a climatological zonal mean January

The effect of radiative heating and cooling by clouds on the available potential energy (APE) is theoretically discussed. It is shown that the cloud radiative contribution to the generation of APE is determined by the net cloud radiative heating and the efficiency factor, which is a function of the temperature distribution of the atmosphere. Results are presented for low and middle cloud effects for three atmospheric layers. Cloud radiative heating is found to be a single function of cloud optical thickness for all classes designed in terms of cloud top heights and optical thickness. Low clouds at low latitudes destroy APE an midclouds generate APE. A concept is developed to relate the cloud radiative heating to cloud heights and optical depths. Cloud-generated radiative heating is computed for January zonal mean conditions for low and midclouds. For both cases, the strongest influence is found in the low troposphere, with marked differences in signs and magnitudes. At extratropical latitudes, both cloud classes generate net radiative cooling. In the tropics, the effect of low cloud changes from net cooling to the net heating as the optical thickness increases, and midclouds cause net heating. A mechanism is described whereby this dependence produces a strong positive feedback effect on the development of SST anomalies in the tropical oceans.

Stuhlmann, R.↗
NASA NTRS1991

Jacobi-Integral Method For Two-Body Problem

Jacobi-integral method enables efficient, accurate computation of trajectory of natural satellite or spacecraft perturbed by component of gravitational potential depending explicitly on both position and time. Instead of total energy, Jacobi integral, which is energylike constant of motion in this case, embedded in Newtonian differential equations of motion. Trajectories computed in fewer steps. With modifications, applicable to such terrestrial problems as motions of rotors and of beams of electrically charged particles in changing electrical and magnetic fields.

Bond, Victor R.↗
NASA NTRS1990

Stellar kinematics of elliptical galaxies in pairs

In both galaxy pairs Arp 166 and 3C 278 the authors find radially increasing velocity dispersions indicating a perturbed, non-equilibrium state of the galaxies after the tidal interaction. In all galaxies, the increase is most pronounced in the regions which correspond to the centers of the outer isophotes. The authors suggest a scenario in which the galaxies are strongly decelerated on their orbits during the encounter. The deceleration depends on the radial position in the perturbed galaxy and vanishes in the center of the perturbed galaxy (Spitzer, 1958). In addition, the crossing time of the stars near the center is very short, implying that the tidal perturbations can be averaged over several orbital periods (e.g., Binney and Tremaine, 1987). In consequence, the central parts are not affected by the tidal interaction while the outer parts are strongly decelerated. This leads to a displacement of the central parts of the galaxies with respect to their envelopes in an anti-symmetrical way for the two components of each galaxy pair. The motions of the central parts subsequently are opposed by dynamical friction with the surrounding envelopes. Due to dynamical friction, the density of the stars increases in the wakes of the moving central parts (Mulder, 1983). The overdensity of stars in the wakes of the moving central parts efficiently decelerates the motions of the central parts. The reaction of the stars in the overdensity regions leads to an increase of the velocity dispersion mainly along the orbits of the moving central parts. The presented observations, especially the asymmetrical luminosity profiles and the radially increasing velocity dispersions support consistently the above scenario of tidal interaction between galaxies. Further spectroscopic observations are necessary in order to investigate the degree of anisotropy in the kinematically perturbed regions.

Madejsky, Rainer↗
NASA NTRS1991

Interrelation of soft and hard X-ray emissions during solar flares. I - Observations

The interrelation between the acceleration and heating of electrons and ions during impulsive solar flares is determined on the basis of simulataneous observations of hard and soft X-ray emission from the Solar Maximum Mission at high time resolution (6 s). For all the flares, the hard X-rays are found to have a power-law spectrum which breaks down during the rise phase and beginning of the decay phase. After that, the spectrum changes to either a single power law or a power law that breaks up at high energies. The characteristics of the soft X-ray are found to depend on the flare position. It is suggested that small-scale quasi-static electric fields are important for determining the acceleration of the X-ray-producing electrons and the outflowing chromospheric ions.

Winglee, R. M.↗
NASA NTRS1992

AXAF VETA-I mirror encircled energy measurements and data reduction

The AXAF VETA-I mirror encircled energy was measured with a series of apertures and two flow gas proportional counters at five X-ray energies ranging from 0.28 to 2.3 keV. The proportional counter has a thin plastic window with an opaque wire mesh supporting grid. Depending on the counter position, this mesh can cause the X-ray transmission to vary as much as +/-9 percent, which directly translates into an error in the encircled energy. In order to correct this wire mesh effect, window scan measurements were made, in which the counter was scanned in both horizontal (Y) and vertical (Z) directions with the aperture fixed. Post VETA measurement of the VXDS setup were made to determine the exact geometry and position of the mesh grid. Computer models of the window mesh were developed to simulate the X-ray transmission based on this measurement. The window scan data were fitted to such mesh models and corrections were made. After this study, the mesh effect was well understood and the final results of the encircled energy were obtained with an uncertainty of less than 0.8 percent.

Zhao, Ping↗
NASA NTRS1993

The propagation of low-frequency whistler waves driven by ion beams in the magnetotail

The generation and propagation of low-frequency whistler waves excited by ion beams in the plasma sheet boundary layer are followed using standard ray tracing techniques and assuming a Harris-type neutral sheet magnetic field profiles. The density is chosen such that the total pressure remains constant. The wave energy is calculated along the wave path taking into account growth due to the ion beam while the wave is in the plasma sheet boundary layer as well as damping due to resonant interactions with the background plasma. The results show that the electromagnetic waves are guided toward the central plasma sheet by the plasma gradients but are damped out before reaching the neutral plane itself due to Cerenkov resonance with the hot central plasma sheet background ions. The amplitudes and final positions of the waves depend on the temperature of the background plasma, the ion beam drift speed, and the ion beam thermal speed.

Burinskaia, T.↗
NASA NTRS1993

Microwave emission from a sunspot. II - The center-to-limb variation

The center-to-limb variation of both the spectral and spatial brightness distributions is investigated using a series of microwave observations of a sunspot in the active region NOAA 4741. Depending on the heliocentric position of the sunspot, the microwave emission appears in two typical profiles: either a ring structure near the center of the disk or a single-peak structure near the limb. Due to the increase of the gyroresonance opacity of the field lines near the spot center as the viewing angle increases, the brightness temperature at high, optically thin frequencies increases slightly as the spot approaches the limb. In addition, a change of effective harmonic, which accompanies a discontinuous change in the degree of polarization, characterizes the center-to-limb variation of the gyroresonance spectrum. Finally, the height of the gyroresonance layer, low in the corona of the active region, is determined from a change of spectrum from gyroresonance to free-free emission as the spot passes over the solar limb.

Lee, Jeongwoo W.↗
NASA NTRS1993

AXAF VETA-I mirror encircled energy measurements and data reduction

The AXAF VETA-I mirror encircled energy was measured with a series of apertures and two flow gas proportional counters at five X-ray energies ranging from 0.28 to 2.3 keV. The proportional counter has a thin plastic window with an opaque wire mesh supporting grid. Depending on the counter position, this mesh can cause the X-ray transmission to vary as much as +/- 9 percent, which directly translates into an error in the encircled energy. In order to correct this wire mesh effect, window scan measurements were made, in which the counter was scanned in both horizontal (Y) and vertical (Z) directions with the aperture fixed. Post VETA measurement of the VXDS setup were made to determine the exact geometry and position of the mesh grid. Computer models of the window mesh were developed to simulate the X-ray transmission based on this measurement. The window scan data were fitted to such mesh models and corrections were made. After this study, the mesh effect was well understood and the final results of the encircled energy were obtained with an uncertainty of less than 0.8 percent.

Zhao, Ping↗
NASA NTRS1993

Computational analysis of off-design waveriders

Comprehensive inviscid and viscous numerical simulations of hypersonic flow past nonconical rounded-nose waveriders are presented. The flow fields and aerodynamic forces at off-design conditions are determined inviscidly by a space-marching CFD code with the initial-data plane provided by a time-marching Navier-Stokes CFD code. Off-design conditions include off-design Mach numbers, angles of attack, and rounded leading edges. A wide range of waverider configurations is investigated and compared. These calculations show the effects of viscous interactions, which are influential near the leading edges, and determine the viscous drag. The inviscid calculations show that L/D decreases as freestream M increases (with alpha = 0). At the on-design Mach numbers, the maximum L/D may occur at slight positive or negative alpha, depending on the shape of the waverider, and zero lift occurs at a negative alpha approximately equal to half of the body thickness. The effects of slight leading-edge blunting produce only local effects in the flow field and small losses in L/D.

He, X.↗
NASA NTRS1922

Airplane stability calculations and their verification by flight tests

For some time, the designers of airplanes have begun to occupy themselves with the question of longitudinal stability. In their quest to simplify calculation and data collection, the designers have attached the greatest importance to the coefficient of initial longitudinal stability. In this study a diagram was constructed from the data of the tunnel tests, which depends neither on the position of the center of gravity nor of the angle of deflection of the elevators. This diagram is constructed by means of straight lines drawn through the metacenters of the complete airplane, in a direction parallel to the tangents to the polar of the airplane relative to a system of axes fixed with reference to the airplane.

STABILITY CALCULATIONS↗
NASA NTRS1957

Investigation of shock-boundary-layer interaction on the spike of a conical-spike nose inlet

Measurements were made of the height of the shock-induced boundary-layer thickening and separation over a Mach number range of 1.6 to 2.0. The behavior of the interaction depended on longitudinal spike position as well as on cone surface Mach number. The cone position affected the interaction by changing the rate of subsonic diffusion and thereby changing the pressure aft of the terminal shock. When the pressure rise due to the interaction exceeded about 1.9, the boundary layer was separated.

Wise, George A↗
NASA NTRS1938

Flow in Smooth Straight Pipes at Velocities Above and Below Sound Velocity

To investigate the laws of flow of compressible fluids in pipes, tests were carried out with air flowing at velocities below and above that of sound in straight smooth pipes. Air was chosen as the flow medium. In order that the effect of compressibility may be brought out most effectively, the velocity should lie between 100 and 500 m/s (200 and 1,000 mph); that is, be of the order of magnitude of the velocity of sound in air. The behavior of the compression shock in a smooth cylindrical pipe was also investigated. The compression shock can occur at any position in the pipe, depending on the throttling downstream, and travels upstream with increasing throttling up to the pipe entrance, so that only subsonic velocities occur in the pipe.

Frossel, W↗
NASA NTRS1992

Thermographic imaging of cracks in thin metal sheets

The presence of cracks significantly decreases the structural integrity of thin metal sheets used in aerospace applications. Thermographic detection of surface temperature variations due to these cracks is possible after external heating. An approximate line source of heat is used to produce an inplane flow of heat in the sheet. A crack in the sheet perturbs the inplane flow of heat and can be seen in an image of the surface temperature of the sheet. An effective technique for locating these perturbations is presented which reduces the surface temperature image to an image of variations in the inplane heat flow. This technique is shown to greatly increase the detectability of the cracks. This thermographic method has advantages over other techniques in that it is able to remotely inspect a large area in a short period of time. The effectiveness of this technique depends on the shape, position and orientation of the heat source with respect to the cracks as well as the extent to which the crack perturbs the surface heat flow. The relationship between these parameters and the variation in the heat flow is determined both by experimental and computational techniques. Experimental data is presented for through-the-thickness, subsurface and surface EDM notches. Data for through-the-thickness fatigue cracks are also presented.

Cramer, K. E.↗