Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Impact load-induced micro-structural damage and micro-structure associated mechanical response of concrete made with different surface roughness and porosity aggregates

The relationship between the nature of micro damage under impact loading and changes in mechanical behavior associated with different microstructures is studied for concretes made with two different coarse aggregates having significant differences mainly in roughness and porosity - sintered fly ash and uncrushed gravel. A range of techniques including X-ray diffraction, digital image analysis, mercury porosimetry, X-ray computed tomography, laser surface profilometry and scanning electron microscopy were used to characterize the aggregates and micro-structures. The concrete prepared with lightweight aggregates was stronger in compression than the gravel aggregate concrete due to enhanced hydration as a result of internal curing. In the lightweight concrete, it was deduced that an inhomogeneous micro-structure led to strain incompatibilities and consequent localized stress concentrations in the mix, leading to accelerated failure. The pore structure, compressibility, and surface texture of the aggregates are of paramount importance for the micro-cracking growth.

36 MATERIALS SCIENCE↗

Use of a liquid-crystal, heater-element composite for quantitative, high-resolution heat transfer coefficients on a turbine airfoil, including turbulence and surface roughness effects

Local heat transfer coefficients were measured along the midchord of a three-times-size turbine vane airfoil in a static cascade operated at roon temperature over a range of Reynolds numbers. The test surface consisted of a composite of commercially available materials: a Mylar sheet with a layer of cholestric liquid crystals, which change color with temperature, and a heater made of a polyester sheet coated with vapor-deposited gold, which produces uniform heat flux. After the initial selection and calibration of the composite sheet, accurate, quantitative, and continuous heat transfer coefficients were mapped over the airfoil surface. Tests were conducted at two free-stream turbulence intensities: 0.6 percent, which is typical of wind tunnels; and 10 percent, which is typical of real engine conditions. In addition to a smooth airfoil, the effects of local leading-edge sand roughness were also examined for a value greater than the critical roughness. The local heat transfer coefficients are presented for both free-stream turbulence intensities for inlet Reynolds numbers from 1.20 to 5.55 x 10 to the 5th power. Comparisons are also made with analytical values of heat transfer coefficients obtained from the STAN5 boundary layer code.

Hippensteele, Steven A.↗

Use of a liquid-crystal and heater-element composite for quantitative, high-resolution heat-transfer coefficients on a turbine airfoil including turbulence and surface-roughness effects

Local heat transfer coefficients were measured along the midchord of a three-times-size turbine vane airfoil in a static cascade operated at room temperature over a range of Reynolds numbers. The test surface consisted of a composite of commercially available materials: a Mylar sheet with a layer of cholestric liquid crystals, which change color with temperature, and a heater made of a polyester sheet coated with vapor-deposited gold, which produces uniform heat flux. After the initial selection and calibration of the composite sheet, accurate, quantitative, and continuous heat transfer coefficients were mapped over the airfoil surface. Tests were conducted at two free-stream turbulence intensities: 0.6 percent, which is typical of wind tunnels; and 10 percent, which is typical of real engine conditions. In addition to a smooth airfoil, the effects of local leading-edge sand roughness were also examined for a value greater than the critical roughness. The local heat transfer coefficients are presented for both free-stream turbulence intensities for inlet Reynolds numbers from 1.20 to 5.55 x 10 to the 5th power. Comparisons are also made with analytical values of heat transfer coefficients obtained from the STAN5 boundary layer code.

Hippensteele, S. A.↗

Ion irradiation effects on Cr-coated zircaloy-4 surface wettability and pool boiling critical heat flux.

The concept of coating the currently used nuclear fuel cladding (zirconium-based alloy, typically Zircaloy-4 or Zirc-4) with an oxidation preventive layer is a progressing Accident tolerant Fuel (ATF) candidate alloys. The coated Zirc-4-based alloys could be a solution to suppress undesirable fast reaction kinetics with high-temperature steam. Zirc-4 has been the most preferred cladding material in pressurized water reactors (PWRs). Chromium (Cr) based alloys as a coating material provides excellent corrosion protection and good strength and wear resistance. In this paper, we present the surface wettability measurements and pool boiling Critical Heat Flux (CHF) for Cr-coated Zirc-4 claddings pre- and post-exposure to an ion irradiation environment. The wettability measurements, including static contact angle (contact angle, θ) and average surface roughness (surface roughness, Ra), are introduced for samples of different coating thicknesses (5–30 μm thick). The coatings fabricated by the cold spray of Cr-Al particles to 10 mm × 10 mm × 1.95 mm Zirc-4 substrates. Post fabrication, a Pilgering (cold rolling) process, was applied to finalize the coating thickness and resulted in a significant reduction in surface roughness of initially fabricated rough surfaces. The process produced three distinguished samples 5-μm unpolished (as machined), 5-μm, and 30-μm polished (cold rolled). The measurements are presented for the three surfaces and bare Zirc-4 as a baseline surface. The contact angle analyses were implemented in theoretical models from the literature to predict pool boiling CHF. Pool boiling experiments were conducted to measure the pool boiling CHF values and compare them to the predicted values. Scanning Electron Microscope (SEM) images and Energy Dispersive X-ray Spectroscopy (EDS) analysis was performed to characterize the surfaces for better understanding and interpreting the results. The SEM images showed localized surface damage due to ion irradiation. No recognized change in the measured surface roughness due to ion irradiation. The contact angles of irradiated Cr-coated surfaces are consistently higher (10°) than pre-irradiated surfaces. Decreasing the Cr-coating layer thickness resulted in lower contact angle pre- and post- ion irradiation. The predicted pool boiling CHF using the Kandlikar model is in good agreement with the experimentally measured CHF values within ±12% for all samples.

36 MATERIALS SCIENCE↗

Effects of surface roughness on the aerodynamic characteristics of the modified 089 B shuttle orbiter at Mach 6 (LA15)

A one hundredth scale model of the modified 089B shuttle orbiter was tested in the Langley 20-Inch Mach 6 tunnel. Force and moment, surface pressure and oilflow data were obtained on one model, and phase-change coating data were obtained on another. The pressure tests were conducted first; the tubes were clipped near the base of the model and then the force and moment and oil flow tests conducted. Angles of attack for the tests were from 20 deg to 35 deg and are commensurate with the range of flight values from entry down to Mach 5. The design flight Reynolds number at Mach 6, based on model length, was 15 million, which could not be obtained in the tunnel; therefore, the tests were conducted at the highest and lowest values for this model in the tunnel, 9.4 million and 4.0 million, respectively, to indicate Reynolds number effects. Two control deflection combinations, representative of the bank and pitch control limits of the design flight trajectory, were used.

Ashby, G. C., Jr.↗

Numerical comparisons of a modified Rayleigh approach with other rough surface EM scattering solutions.

A modification of the classical Rayleigh technique utilizing the fast Fourier transform, developed into the so-called Rayleigh-FFT method for electromagnetic scattering, is shown to obtain valid scattering results from arbitrary irregular periodic structures composed of a rough layer over a rough half-space. The considerable usefulness of the Rayleigh approach is thus established, and Beckmann's (1968) contention (that the convergence of the method is reasonably rapid only if the roughness is very slight) is refuted.

Jiracek, G. R.↗

The effects of Reynolds number, rotor incidence angle and surface roughness on the heat transfer distribution in a large-scale turbine rotor passage

A combined experimental and computational program was conducted to examine the heat transfer distribution in a turbine rotor passage geometrically similar to the Space Shuttle Main Engine (SSME) High Pressure Fuel Turbopump (HPFTP). Heat transfer was measured and computed for both the full span suction and pressure surfaces of the rotor airfoil as well as for the hub endwall surface. The objective of the program was to provide a benchmark-quality database for the assessment of rotor heat transfer computational techniques. The experimental portion of the study was conducted in a large scale, ambient temperature, rotating turbine model. The computational portion consisted of the application of a well-posed parabolized Navier-Stokes analysis of the calculation of the three-dimensional viscous flow through ducts simulating a gas turbine package. The results of this assessment indicate that the procedure has the potential to predict the aerodynamics and the heat transfer in a gas turbine passage and can be used to develop detailed three dimensional turbulence models for the prediction of skin friction and heat transfer in complex three dimensional flow passages.

Blair, M. F.↗

Interactions of light with rough dielectric surfaces - Spectral reflectance and polarimetric properties

The nature of the interactions of visible and NIR radiation with the surfaces of rock and mineral samples was investigated by measuring the reflectance and the polarization properties of scattered and reflected light for slab samples of obsidian and fine-grained basalt, prepared to controlled surface roughness. It is shown that the degree to which radiation can penetrate a surface and then scatter back out, an essential criterion for mineralogic determinations based on reflectance spectra, depends not only upon the composition of the material, but also on its physical condition such as sample grain size and surface roughness. Comparison of the experimentally measured reflectance and polarization from smooth and rough slab materials with the predicted models indicates that single Fresnel reflections are responsible for the largest part of the reflected intensity resulting from interactions with the surfaces of dielectric materials; multiple Fresnel reflections are much less important for such surfaces.

Yon, S. A.↗

Scaling of atomic layer etching of SiO 2 in fluorocarbon plasmas: Transient etching and surface roughness

Fabricating sub-10 nm microelectronics places plasma processing precision at atomic dimensions. Atomic layer etching (ALE) is a cyclic plasma process used in semiconductor fabrication that has the potential to remove a single layer of atoms during each cycle. In self-limiting ideal ALE, a single monolayer of a material is consistently removed in each cycle, typically expressed as EPC (etch per cycle). In plasma ALE of dielectrics, such as SiO 2 and Si 3 N 4 , using fluorocarbon gas mixtures, etching proceeds through deposition of a thin polymer layer and the process is not strictly self-terminating. As a result, EPC is highly process dependent and particularly sensitive to the thickness of the polymer layer. In this paper, results are discussed from a computational investigation of the ALE of SiO 2 on flat surfaces and in short trenches using capacitively coupled plasmas consisting of a deposition step (fluorocarbon plasma) and an etch step (argon plasma). We found that ALE performance is a delicate balance between deposition of polymer during the first half cycle and etching (with polymer removal) during the second half cycle. In the absence of complete removal of the overlying polymer in each cycle, ALE may be transient as the polymer thickness grows with each cycle with a reduction in EPC until the thickness is too large to enable further etching. Small and statistical amounts of polymer left from a previous cycle can produce statistical variation in polymer thickness on the next cycle, which in turn can lead to a spatially dependent EPC and ALE roughness. Based on synergy between T i (sputtering time) and T p (passivation time), dielectric ALE can be described as having three modes: deposition, roughening surface (transitioning to etch-stop), and smooth surface with steady-state EPC.

Materials Science↗

Effect of Surface Roughness on Dynamic Stall in Pitching Motion

Dynamic stall plays a critical role in determining the performance and stability of a wide range of fluid-dynamics systems in various engineering applications. This unsteady aerodynamic phenomenon is particularly significant for maneuvering aircraft wings, jet aircraft subjected to gust encounters, helicopter rotor blades, and wind turbine blades [1–3]. The prediction of the dynamic stall vortex (DSV) is challenging due to factors such as unsteady aerodynamics, three-dimensional (3-D) effects, turbulence and flow separation, incoming gust, and surface impact effects [4–6]. Hence, advanced computational techniques and modeling approaches in computational fluid dynamics (CFD) would be required to enhance the accuracy and reliability of DSV predictions in dynamic stall scenarios. In the past, Batther and Lee [7] employed delayed detached eddy simulations (DDES) to understand the flow physics associated with the onset of dynamic stall. Their approach demonstrated that DDES achieves results comparable to those obtained from large-eddy simulations at a reduced computational cost. In another study, Khalifa et al. [8] examined the 3-D aspects of dynamic stall on a NACA 0012 airfoil using DES solvers. In conclusion, the findings underlined the superiority of 3-D simulations over two-dimensional approaches, particularly in predicting the lift coefficient values and capturing dynamic stall stages more precisely.

97 MATHEMATICS AND COMPUTING↗

Strain-induced reduction of surface roughness dominated spin relaxation in MOSFETs

Semiconductor spintronics is a rapidly developing field with large impact on microelectronics. Using spin may help to reduce power consumption and increase computational speed. Silicon is perfectly suited for spin-based applications. It is characterized by a weak spin-orbit interaction which should result in a long spin lifetime. However, recent experiments indicate the lifetime is greatly reduced in gated structures. Thus, understanding the peculiarities of the spin-orbit effects on the subband structure and details of the spin propagation in surface layers and thin silicon films is urgently needed. We investigate the contribution of the spin-orbit interaction to the equivalent valley splitting and calculate the spin relaxation matrix elements by using a perturbative k ⋅p approach. We demonstrate that applying uniaxial stress along the [110] direction may considerably suppress electron spin relaxation in silicon surface layers and thin films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Numerical Study of Solar Receiver Tube With Modified Surface Roughness for Enhanced and Selective Absorptivity in Concentrated Solar Power Tower

Abstract Concentrated solar power (CSP) is a reliable renewable energy source that is progressively lowering its cost of energy. However, the heat loss due to reflected and emitted radiation hinders the maximum achievable thermal efficiency for solar receiver tubes on the solar tower. Current solar selective coatings cannot withstand the high temperatures that come with state-of-the-art CSP towers often needing to be recoated soon after initial operation. We intend to use Inconel 718 with different additive manufacturing (AM) practices to construct surfaces that allow for more light-trapping to occur. By adjusting printing parameters, we can tailor a surface to allow for more absorption while diminishing emitted radiation heat loss. By using COMSOL Multiphysics, we can generate these theoretical surfaces to emulate a printed surface, and using the coupled Multiphysics we can simulate how the surface dictates radiation properties. Our results show that by having a rougher surface we can enhance the absorptivity of Inconel 718 (IN718) by 38.8%. We expect this work to transform how solar absorber tubes are manufactured without using selective coatings and supplement the US Department of Energy (DOE) 2030 SunShot Initiative.

14 SOLAR ENERGY↗

β-(1,3)-Glucan Unmasking in Some Candida albicans Mutants Correlates with Increases in Cell Wall Surface Roughness and Decreases in Cell Wall Elasticity

Candida albicans is among the most common human fungal pathogens, causing a broad range of infections, including life-threatening systemic infections. The cell wall of C. albicans is the interface between the fungus and the innate immune system. The cell wall is composed of an outer layer enriched in mannosylated glycoproteins (mannan) and an inner layer enriched in β-(1,3)-glucan and chitin. Detection of C. albicans by Dectin-1, a C-type signaling lectin specific for β-(1,3)-glucan, is important for the innate immune system to recognize systemic fungal infections. Increased exposure of β-(1,3)-glucan to the immune system occurs when the mannan layer is altered or removed in a process called unmasking. Nanoscale changes to the cell wall during unmasking were explored in this paper in live cells with atomic force microscopy (AFM). Two mutants, the cho1Δ/Δ and kre5Δ/Δ mutants, were selected as representatives that exhibit modest and strong unmasking, respectively. Comparisons of the cho1Δ/Δ and kre5Δ/Δ mutants to the wild type reveal morphological changes in their cell walls that correlate with decreases in cell wall elasticity. In addition, AFM tips functionalized with Dectin-1 revealed that the forces of binding of Dectin-1 to all of the strains were similar, but the frequency of binding was highest for the kre5Δ/Δ mutant, decreased for the cho1Δ/Δ mutant, and rare for the wild type. These data show that nanoscale changes in surface topology are correlated with increased Dectin-1 adhesion and decreased cell wall elasticity. Finally, AFM, using tips functionalized with immunologically relevant molecules, can map epitopes of the cell wall and increase our understanding of pathogen recognition by the immune system.

59 BASIC BIOLOGICAL SCIENCES↗