Search NASA⌕ Search

SEARCH · Search NASA

Results for “static engine”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

PdCr based high temperature static strain gage

The program at NASA Lewis Research Center to develop a high temperature static strain gage system for the hypersonic vehicle and turbine engine research has emphasized a palladium-13 wt pct chromium (PdCr) alloy. Gages made from this alloy are being developed in both fine wire and thin film form. The wire gage system had platinum wire as a temperature compensator and was coated with a special alumina and zirconia mixture overcoat. This PdCr compensated wire gage responded linearly to the imposed strain to at least 1000 microstrain. The apparent strain varied within 300 microstrain from room temperature to 800 C with a reproducibility within 50 microstrain between thermal cycles to 800 C. The sputtered thin film PdCr strain gage, whose size was 8 x 8 mm and 10 microns thick, has demonstrated the possibility of extending the use of the PdCr strain gage to a temperature of approximately 1000 C.

Lei, Jih-Fen↗
NASA NTRS1992

Pd/Cr Strain Gauges For High Temperatures

Temperature-compensated Pd/Cr electrical-resistance strain gauges measure static strains in combustors, blades, and vanes of gas turbine engines. Made of alloy of 87 weight percent Pd and 13 weight percent Cr. Microstructure highly stable; undergoes no transformation of phase between ambient temperature and 1,000 degrees C. Gives highly repeatable readings with low drift at temperatures from ambient to 600 degrees C.

Lei, Jih-Fen↗
NASA NTRS1990

SIRTF primary mirror design, analysis, and testing

The primary mirror assembly (PMA) requirements and concepts for the Space Infrared Telescope Facility (SIRTF) program are discussed. The PMA studies at NASA/ARC resulted in the design of two engineering test articles, the development of a mirror mount cryogenic static load testing system, and the procurement and partial testing of a full scale spherical mirror mounting system. Preliminary analysis and testing of the single arch mirror with conical mount design and the structured mirror with the spherical mount design indicate that the designs will meet all figure and environmental requirements of the SIRTF program.

Sarver, George L., III↗
NASA NTRS1993

Navier-Stokes calculations for the unsteady flowfield of turbomachinery

The Multistage Unsteady Turbomachinery Code is presently used to numerically simulate the flowfield generated by rotating machinery. The code, which simplifies the Reynolds-averaged Navier-Stokes equations via the thin-layer approximation, is an implicit finite-volume scheme with flux Jacobians that are evaluated by flux-vector splitting, while residual fluxes are evaluated by flux-difference splitting. Attention is given to the computational results this obtained for three engineering problems, involving propfan, rotating blade, and both rotating and static blade flows.

Chen, Jen P.↗
NASA NTRS1994

Correlation of finite element free vibration predictions using random vibration test data

Finite element analysis is regularly used during the engineering cycle of mechanical systems to predict the response to static, thermal, and dynamic loads. The finite element model (FEM) used to represent the system is often correlated with physical test results to determine the validity of analytical results provided. Results from dynamic testing provide one means for performing this correlation. One of the most common methods of measuring accuracy is by classical modal testing, whereby vibratory mode shapes are compared to mode shapes provided by finite element analysis. The degree of correlation between the test and analytical mode shapes can be shown mathematically using the cross orthogonality check. A great deal of time and effort can be exhausted in generating the set of test acquired mode shapes needed for the cross orthogonality check. In most situations response data from vibration tests are digitally processed to generate the mode shapes from a combination of modal parameters, forcing functions, and recorded response data. An alternate method is proposed in which the same correlation of analytical and test acquired mode shapes can be achieved without conducting the modal survey. Instead a procedure is detailed in which a minimum of test information, specifically the acceleration response data from a random vibration test, is used to generate a set of equivalent local accelerations to be applied to the reduced analytical model at discrete points corresponding to the test measurement locations. The static solution of the analytical model then produces a set of deformations that once normalized can be used to represent the test acquired mode shapes in the cross orthogonality relation. The method proposed has been shown to provide accurate results for both a simple analytical model as well as a complex space flight structure.

Chambers, Jeffrey A.↗
NASA NTRS1995

Mechanical properties testing and results for thermal barrier coatings

The paper reports on several years of mechanical testing of thermal barrier coatings. The test results were generated to support the development of durability models for the coatings in heat engine applications. The test data that are reviewed include modulus, static strength, and fatigue strength data. The test methods and results are discussed, along with the significant difficulties inherent in mechanical testing of thermal barrier coating materials. The materials include 7 percent wt. and 8 percent wt. yttria, partially stabilized zirconia as well as a cermet material. Both low pressure plasma spray and electron-beam physical vapor deposited coatings were tested. The data indicate the basic trends in the mechanical properties of the coatings over a wide range of isothermal conditions. Some of the trends are correlated with material density.

Thomas A. Cruse↗
NASA NTRS2009

Explicit Finite Element Modeling of Multilayer Composite Fabric for Gas Turbine Engine Containment Systems, Phase II: Material Model Development and Simulation of Experiments - Part 3

A team consisting of Arizona State University, Honeywell Engines, Systems & Services, the National Aeronautics and Space Administration Glenn Research Center, and SRI International collaborated to develop computational models and verification testing for designing and evaluating turbine engine fan blade fabric containment structures. This research was conducted under the Federal Aviation Administration Airworthiness Assurance Center of Excellence and was sponsored by the Aircraft Catastrophic Failure Prevention Program. The research was directed toward improving the modeling of a turbine engine fabric containment structure for an engine blade-out containment demonstration test required for certification of aircraft engines. The research conducted in Phase II began a new level of capability to design and develop fan blade containment systems for turbine engines. Significant progress was made in three areas: (1) further development of the ballistic fabric model to increase confidence and robustness in the material models for the Kevlar(TradeName) and Zylon(TradeName) material models developed in Phase I, (2) the capability was improved for finite element modeling of multiple layers of fabric using multiple layers of shell elements, and (3) large-scale simulations were performed. This report concentrates on the material model development and simulations of the impact tests.

Zylon↗
NASA NTRS2006

Predicting Lifetime of a Thermomechanically Loaded Component

NASALIFE is a computer program for predicting the lifetime, as affected by low cycle fatigue (LCF) and creep rupture, of a structural component subject to temporally varying, multiaxial thermomechanical loads. The component could be, for example, part of an aircraft turbine engine. Empirical data from LCF tests, creep rupture tests, and static tensile tests are used as references for predicting the number of missions the component can withstand under a given thermomechanical loading condition. The user prepares an input file containing the creep-rupture and cyclic-fatigue information, temperature-dependent material properties, and mission loading and control flags. The creep rupture information can be entered in tabular form as stress versus life or by means of parameters of the Larson-Miller equation. The program uses the Walker mean-stress model to adjust predicted life for ranges of the ratio between the maximum and minimum stresses. Data representing complex load cycles are reduced by the rainflow counting method. Miner's rule is utilized to combine the damage at different load levels. Finally, the program determines the total damage due to creep and combines it with the fatigue damage due to the cyclic loading and predicts the approximate number of missions a component can endure before failing.

Murthy, Pappu L. N.↗
NASA NTRS2009

Control-Relevant Modeling, Analysis, and Design for Scramjet-Powered Hypersonic Vehicles

Within this paper, control-relevant vehicle design concepts are examined using a widely used 3 DOF (plus flexibility) nonlinear model for the longitudinal dynamics of a generic carrot-shaped scramjet powered hypersonic vehicle. Trade studies associated with vehicle/engine parameters are examined. The impact of parameters on control-relevant static properties (e.g. level-flight trimmable region, trim controls, AOA, thrust margin) and dynamic properties (e.g. instability and right half plane zero associated with flight path angle) are examined. Specific parameters considered include: inlet height, diffuser area ratio, lower forebody compression ramp inclination angle, engine location, center of gravity, and mass. Vehicle optimizations is also examined. Both static and dynamic considerations are addressed. The gap-metric optimized vehicle is obtained to illustrate how this control-centric concept can be used to "reduce" scheduling requirements for the final control system. A classic inner-outer loop control architecture and methodology is used to shed light on how specific vehicle/engine design parameter selections impact control system design. In short, the work represents an important first step toward revealing fundamental tradeoffs and systematically treating control-relevant vehicle design.

Rodriguez, Armando A.↗
NASA NTRS1990

A test fixture for measuring high-temperature hypersonic-engine seal performance

A test fixture for measuring the performance of several high temperature engine seal concepts was installed at the NASA Lewis Research Center. The test fixture was developed to evaluate seal concepts under development for advanced hypersonic engines such as those being considered for the National Aerospace Plane. The fixture can measure static seal leakage performance from room temperature up to 1500 F and air pressure differentials up to 100 psi. Performance of the seals can be measured while sealing against flat or engine simulated distorted walls, where distortions can be as large as 0.150 in. in only an 18 in. span. The fixture is designed to evaluate seals 3 feet long, a typical engine panel length. The seal channel can be configured to test square, circular, or rectangular seals that are nominally 0.5 in. high. The sensitivity of leakage performance to lateral or axial loading can also be measured using specially designed high temperature lateral and axial bellows preload systems. Leakage data for a candidate ceramic wafer engine seal is provided by way of example to demonstrate the test fixture's capabilities.

Steinetz, Bruce M.↗
NASA NTRS1978

Quiet Clean Short-haul Experimental Engine (QCSEE) composite fan frame design report

An advanced composite frame which is flight-weight and integrates the functions of several structures was developed for the over the wing (OTW) engine and for the under the wing (UTW) engine. The composite material system selected as the basic material for the frame is Type AS graphite fiber in a Hercules 3501 epoxy resin matrix. The frame was analyzed using a finite element digital computer program. This program was used in an iterative fashion to arrive at practical thicknesses and ply orientations to achieve a final design that met all strength and stiffness requirements for critical conditions. Using this information, the detail design of each of the individual parts of the frame was completed and released. On the basis of these designs, the required tooling was designed to fabricate the various component parts of the frame. To verify the structural integrity of the critical joint areas, a full-scale test was conducted on the frame before engine testing. The testing of the frame established critical spring constants and subjected the frame to three critical load cases. The successful static load test was followed by 153 and 58 hours respectively of successful running on the UTW and OTW engines.

Mitchell, S. C.↗
NASA NTRS1984

Ceramic component development for the AGT101 gas turbine engine

Under DOE/NASA sponsorship, a team is developing the AGT101, a highly efficient gas turbine engine for automotive application. The regenerated engine will operate at a maximum of 1370 C (2500 F) and 100,000 rpm, and will utilize a variety of Si3N4, SiC, lithium aluminum silicate and ceramic fiber insulation components. Engine design has been performed to consider the fabrication and material characteristics of these ceramic materials for both the static and rotating hot section components. Component fabrication has been performed, components have been screened in thermal and mechanical tests, and initial engine testing has been performed.

Carruthers, W. D.↗
NASA NTRS2002

Comparison of Engine Cycle Codes for Rocket-Based Combined Cycle Engines

This paper summarizes the results from a one day workshop on Rocket-Based Combined Cycle (RBCC) Engine Cycle Codes held in Monterey CA in November of 2000 at the 2000 JANNAF JPM with the authors as primary participants. The objectives of the workshop were to discuss and compare the merits of existing Rocket-Based Combined Cycle (RBCC) engine cycle codes being used by government and industry to predict RBCC engine performance and interpret experimental results. These merits included physical and chemical modeling, accuracy and user friendliness. The ultimate purpose of the workshop was to identify the best codes for analyzing RBCC engines and to document any potential shortcomings, not to demonstrate the merits or deficiencies of any particular engine design. Five cases representative of the operating regimes of typical RBCC engines were used as the basis of these comparisons. These included Mach 0 sea level static and Mach 1.0 and Mach 2.5 Air-Augmented-Rocket (AAR), Mach 4 subsonic combustion ramjet or dual-mode scramjet, and Mach 8 scramjet operating modes. Specification of a generic RBCC engine geometry and concomitant component operating efficiencies, bypass ratios, fuel/oxidizer/air equivalence ratios and flight dynamic pressures were provided. The engine included an air inlet, isolator duct, axial rocket motor/injector, axial wall fuel injectors, diverging combustor, and exit nozzle. Gaseous hydrogen was used as the fuel with the rocket portion of the system using a gaseous H2/O2 propellant system to avoid cryogenic issues. The results of the workshop, even after post-workshop adjudication of differences, were surprising. They showed that the codes predicted essentially the same performance at the Mach 0 and I conditions, but progressively diverged from a common value (for example, for fuel specific impulse, Isp) as the flight Mach number increased, with the largest differences at Mach 8. The example cases and results are compared and discussed in this paper.

Waltrup, Paul J.↗
NASA NTRS1976

Low-speed wind-tunnel tests of a large scale blended arrow advanced supersonic transport model having variable cycle engines and vectoring exhaust nozzles

A low-speed wind-tunnel investigation was conducted in a full-scale tunnel to determine the performance and static stability and control characteristics of a large-scale model of a blended-arrow advanced supersonic transport configuration incorporating variable-cycle engines and vectoring exhaust nozzles. Configuration variables tested included: (1) engine mode (cruise or low-speed), (2) engine exit nozzle deflection, (3) leading-edge flap geometry, and (4) trailing-edge flap deflection. Test variables included values of C sub micron from 0 to 0.38, values of angle of attack from -10 degrees to 30 degrees, values of angle of sideslip, from -5 degrees to 5 degrees, and values of Reynolds number, from 3.5 million to 6.8 million.

Parlett, L. P.↗
NASA NTRS1952

Dynamic response at altitude of a turbojet engine with variable area exhaust nozzle

The dynamic characteristics of turbojet engine with variable exhaust nozzle area were investigated over a range of altitudes and flight Mach numbers. These characteristics generalize to standard static level condition. Data resulting from approximate step disturbances in either manipulated variable suggested functional relationships from which functions can be derived. The constants of the transfer functions are listed for five combinations of engine speed and exhaust nozzle area. The minimum data needed to completely define the transfer functions were: experimentally determined dynamic characteristics, such as engine time constant and initial rise ratio, resulting from either manipulated variable; static characteristics determined from steady-state performance curves.

Delio, Gene J↗
NASA NTRS1972

Flight investigation of an air-cooled plug nozzle with afterburning turbojet

A convectively cooled plug nozzle, using 4 percent of the engine air as the coolant, was tested in 1967 K (3540 R) temperature exhaust gas. No significant differences in cooling characteristics existed between flight and static results. At flight speeds above Mach 1.1, nozzle performance was improved by extending the outer shroud. Increasing engine power improved nozzle efficiency considerably more at Mach 1.2 than at 0.9. The effect of nozzle pressure ratio and secondary weight flow on nozzle performance are also presented.

Samanich, N. E.↗
DOE OSTI2025

Maturing Rational Design Methodologies and Industry Consensus Engineering Standards: Critical Fastened Joints - Solar PV Industry

Critical structural joints can be seen throughout a solar array and are called upon to secure modules and keep racking assembled and able to resist large demands from winds and snow loads. In the relatively new and fast-growing solar PV industry, the important role these hardware assemblies (e.g. clips, clamps, bolts, nuts, washers) play is not well understood by product designers. Failures with critical structural joints are surprisingly common and point to the need for maturing the engineering and assembly of these joints. The wide variety of design concepts (Figure 2&2) demonstrate interesting and innovative ideas but are lacking the basics of fastener engineering seen in matured industries (e.g. transportation, buildings). Complicating the maturing process for critical structural joints is that they are one component in rack supporting structures that exhibits a systems behavior; each component will affect the other and play a key role in maintaining structural integrity. When wind loads the surface of a module, the underlying racking members deflect and twist which in turn imparts forces back into the joints and into the mounted modules. Often, these supporting rack structures exhibit high deflections and low natural frequencies which amplify the demands placed into the joints even in moderate winds. Current engineering practices and associated structural conventions view solar racking support structures as they would a high mass building that exhibit more static behaviors in wind events. Solar structures are unique from high mass buildings and require the development of solar specific industry engineering consensus standards.

14 SOLAR ENERGY↗
NASA NTRS1972

Design study of an air pump and integral lift engine ALF-504 using the Lycoming 502 core

Design studies were conducted for an integral lift fan engine utilizing the Lycoming 502 fan core with the final MQT power turbine. The fan is designed for a 12.5 bypass ratio and 1.25:1 pressure ratio, and provides supercharging for the core. Maximum sea level static thrust is 8370 pounds with a specific fuel consumption of 0.302 lb/hr-lb. The dry engine weight without starter is 1419 pounds including full-length duct and sound-attenuating rings. The engine envelope including duct treatment but not localized accessory protrusion is 53.25 inches in diameter and 59.2 inches long from exhaust nozzle exit to fan inlet flange. Detailed analyses include fan aerodynamics, fan and reduction gear mechanical design, fan dynamic analysis, engine noise analysis, engine performance, and weight analysis.

Rauch, D.↗