Search NASA⌕ Search

SEARCH · Search NASA

Results for “stream flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Wind tunnel performance of four energy efficient propellers designed for Mach 0.8 cruise

For the advanced turboprop to be competitive with proposed advanced turbofan-powered aircraft, it must have high propulsive efficiency at Mach 0.8 cruise above 9.144-km altitude with an acceptable cabin noise environment. Four 8-bladed propeller models are designed employing various concepts to reduce compressibility losses. Wind tunnel tests are conducted at zero model incidence to the free-stream flow. Aerodynamic and acoustic test results are presented and discussed. It is shown that the aeroacoustically designed configuration (SR-3) with 45 deg of tip sweep and an area-ruled spinner yields the highest propulsive efficiency (78.7% at Mach 0.8, 3.06 advance ratio, and 1.7 power coefficient), with an improvement of about 3% over the straight bladed configuration (SR-2, with zero-degree sweep). The phase-interference concept for noise reduction used in SR-3 yields about 5-6 dB reduction as compared to SR-2.

Jeracki, R. J.↗

Far-field radiation of aft turbofan noise

Approximate expressions were developed for the noise radiation from the aft duct. The results of approximate aft radiation equation compare favorably to more exact Wiener-Hopf radiation results. Refraction as well as convective effects in the multiple flow streams is considered. The peak in the radiation pattern, which occurs nearly at engine sideline, is composed of modes with relatively large cut-off ratios. This implies that aft fan radiation will be inherently more difficult to suppress that the fan inlet noise. The theoretical multimodal radiation pattern is compared to experimental data for the first two harmonics of blade passage frequency for three full scale fans at two speeds. The agreement between theory and experiment is quite good.

Rice, E. J.↗

Use of satellite data in runoff forecasting in the heavily forested, cloud-covered Pacific Northwest

The author has identified the following significant results. Satellite-derived snow cover data improves forecasts of stream flow but not at a statistically significant amount and should not be used exclusively because of persistent cloud cover. Based upon reconstruction runs, satellite data can be used to augment snow-flight data in the Upper Snake, Boise, Dworshak, and Hungry Horse basins. Satellite data does not compare well with aerial snow-flight data in the Libby basin.

Dillard, J. P.↗

A diagonal form of an implicit approximate-factorization algorithm with application to a two dimensional inlet

A modification of an implicit approximate-factorization finite-difference algorithm applied to the two dimensional Euler and Navier-Stokes equations in general curvilinear coordinates is presented for supersonic free stream flow about and through inlets. The modification transforms the coupled system of equations into an uncoupled diagonal form which requires less computation work. For steady-state applications the resulting diagonal algorithm retains the stability and accuracy characteristics of the original algorithm. Solutions are given for inviscid and laminar flow about a two dimensional wedge inlet configuration. Comparisons are made between computed results and exact theory.

Chaussee, D. S.↗

Method of forming frozen spheres in a force-free drop tower

Hollow glass spheres are shaped by the effects of surface tension acting on bubbles of glass in its molten state. A downwardly flowing stream of air accelerated at a one-G rate of acceleration is established through a drop bubbles on molten glass are introduced into the stream of air and frozen and as they are accelerated at a one-G rate of acceleration.

Kendall, J. M., Jr.↗

Longitudinal afterbody grooves and shoulder radiusing for low-speed bluff body drag reduction

A new low-speed drag reduction approach is proposed which employs longitudinal surface V-shaped grooves cutting through the afterbody shoulder region. The test Reynolds number range was from 20,000 to 200,000 based on undisturbed free-stream flow and a body diameter of 6.08 cm. The V-grooves are shown to be most effective in reducing drag when the afterbody shoulder radius is zero. Reductions in drag of up to 33% have been measured for this condition. For large shoulder radius, the grooves are only effective at the lower Reynolds numbers of the test.

Howard, F. G.↗

Soil Moisture Project Evaluation Workshop

Approaches planned or being developed for measuring and modeling soil moisture parameters are discussed. Topics cover analysis of spatial variability of soil moisture as a function of terrain; the value of soil moisture information in developing stream flow data; energy/scene interactions; applications of satellite data; verifying soil water budget models; soil water profile/soil temperature profile models; soil moisture sensitivity analysis; combinations of the thermal model and microwave; determing planetary roughness and field roughness; how crust or a soil layer effects microwave return; truck radar; and truck/aircraft radar comparison.

Gilbert, R. H.↗

Applications of remote sensing technology to U.S. Water resource management

Applications of Landsat data to assessing the available water supply in the U.S. for agricultural puposes as a program of the NASA Office of Space Science and Applications are described. Snow melt runoff predictions are performed with multitemporal Landsat imagery to measure the extent of mountain snow packs in the Rockies in order to produce stream flow forecast models. The data is used for decisions of which crops to plant, based on irrigation water which will be accessible in eleven western U.S. states. Imagery has tracked the growth of irrigated lands watered from the Ogallala aquifer in the central U.S., and is providing a data base for calculating the aquifer depletion rates. Studies are preceeding in temporally mapping the kinds of vegetation growing in the Suwannee Sound in Florida to monitor the intrusion of salt water, which would reduce the River's usefulness for irrigation. Finally, capabilities of the Thematic Mapper are reviewed.

Weber, J. D.↗

Reduction of the shock wave intensity by modifying the transonic blade trailing edge

It is shown that the shock wave intensity can be decreased by using modified trailing edge configurations to reduce or even completely compensate for the effect of the finite thickness of the trailing edge. A theoretical analysis is presented together with numerical results for two supersonic streams flowing off the trailing edge at different velocities. The analysis is based on an ideal gas model.

Doerffer, P.↗

Propagation of energetic electron streams in solar flares

The microscopic stability of an electron stream flowing down to the photosphere from the corona is examined. It is found that, while a power-law distribution is stable in the low-density corona, it is unstable against the generation of magnetized electron plasma waves in the high-density photosphere. The scattering of these energetic electrons may alter their radiation signatures.

Mok, Y.↗

Dilution jet mixing program, supplementary report

The velocity and temperature distributions predicted by a 3-D numerical model and experimental measurements are compared. Empirical correlations for the jet velocity trajectory developed are presented. The measured velocity distributions for all test cases of phase through phase 3 are presented in the form of contour and oblique plots. quantification of the effects of the following on the jet mixing characteristics with a confined crossflow are: (1) orifice geometry momentum flux ratio and density ratio; (2) nonuniform mainstream temperature and velocity profiles upstream of dilution orifices; (3) cold versus hot jet injection; (4) cross-stream flow are a convergence as encountered in practical dilution zone geometries; (5) 2-D slot versus circular orifices; (6) discrete noncirculcer orifices; (7) single-sided versus opposed jets; (8) single row of jets.

Srinivasan, R.↗

Effects of inlet distortion on a static pressure probe mounted on the engine hub in an F-15 airplane

Problems encountered in obtaining good engine face pressure data were studied. A single static measurement located upstream of the engine hub in the stream flow was found to provide a pressure signal suitable for engine control. Two identical probes for measuring fan inlet static (PS2) pressure were designed and mounted on the hub of the left F100-PW-100 turbofan engine installed in the F-15 test aircraft for flight evaluation. The probe is used as a static pressure sensor for a digital engine control system.

Hughes, D. L.↗

Turbulent flow model for vapor collection efficiency of a high-purity silicon reactor

In this study a mathematical model and a computer code based on this model was developed to allow prediction of the product distribution in chemical reactors for converting gaseous silicon compounds to condensed-phase silicon. Specifically, the model formulated describes the silicon vapor separation/collection from the developing turbulent flow stream within reactors of the Westinghouse type. Migration of the silicon vapor to the reactor walls was described by the parametric solutions presented here, in order to reduce the experimentation necessary in the design of such reactors. Calculations relating to the collection efficiencies of such reactors are presented as a function of the reactor throughflow and distance along its length.

Srivastava, R.↗

Microstructure and stability of melt spun INCONEL 713 LC

The alloy IN-714LC was used in an investigation of the effect of process parameters on the microstructure of a rapidly solidified melt-spun material. The resultant ribbon microstructure consisted of several distinct regions, each of which corresponds to a different thermal history during processing. A chill zone of equiaxed randomly-oriented grains exists in a region of the foil which was in contact with the wheel during casting. This zone develops into a dendritic growth morphology with distance away from the lower ribbon surface. Dendrites inclined in the direction of wheel rotation result from growth into a flowing stream. TEM studies showed that a cell structure formed, the cell size decreasing with increasing wheel speed. Aging studies indicated that the cell structure plays an important role in gamma prime precipitation. Results relating to heat treatments (as would be encountered in compaction and use) and the stability of the melt-spun structure are considered.

Antolovich, S. D.↗

Coherent structures and modeling: Some background comments

Coherent structures are discussed as a sequence of events (identifiable motions) in the flow which convert significant amounts of mechanical energies of the mean flow stream, into turbulent fluctuations. The use of structure information in modeling is also discussed.

Kline, S. J.↗

Computer programs for calculation of sting pitch and roll angles required to obtain angles of attack and sideslip on wind tunnel models

Two programs have been developed to calculate the pitch and roll angles of a wind-tunnel sting drive system that will position a model at the desired angle of attack and and angle of sideslip in the wind tunnel. These programs account for the effects of sting offset angles, sting bending angles and wind-tunnel stream flow angles. In addition, the second program incorporates inputs from on-board accelerometers that measure model pitch and roll with respect to gravity. The programs are presented in the report and a description of the numerical operation of the programs with a definition of the variables used in the programs is given.

Peterson, John B., Jr.↗

A test for interfacial effects and stress transfer in ceramic matrix composites

The efforts to fabricate single embedded filament specimens of carbon and SiC fibers were unsuccessful largely due to the thermal stresses resulting from differences in thermal coefficient of expansion. Other factors appear to have been involved including embrittlement of the metal substrate by the H2 gas in the chemical vapor deposition flow stream and reaction layers formed between the silicon carbide and the metal substrate. The carbon fiber may have been attacked by the CVD reactant. It is concluded that these differential stresses are so large as to make the embedded fiber test impractical for the study of interphase effects and stress transfer in fiber ceramic matrix systems.

Bascom, Willard D.↗

Isotope exchange in oxide-containing catalyst

A method of exchanging rare-isotope oxygen for common-isotope oxygen in the top several layers of an oxide-containing catalyst is disclosed. A sample of an oxide-containing catalyst is exposed to a flowing stream of reducing gas in an inert carrier gas at a temperature suitable for the removal of the reactive common-isotope oxygen atoms from the surface layer or layers of the catalyst without damaging the catalyst structure. The reduction temperature must be higher than any at which the catalyst will subsequently operate. Sufficient reducing gas is used to allow removal of all the reactive common-isotope oxygen atoms in the top several layers of the catalyst. The catalyst is then reoxidized with the desired rare-isotope oxygen in sufficient quantity to replace all of the common-isotope oxygen that was removed.

Robert V Hess↗