Search NASA⌕ Search

SEARCH · Search NASA

Results for “supersonic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Aerodynamic Performance of a Supersonic Throughflow Fan Stage With a Convergent Flow Path

The results from an experimental evaluation of a supersonic throughflow (SSTF) fan stage with a convergent flow path are presented. The stage was designed for a pressure ratio of 2.46 at a tip speed of 1350 ft/s and an inlet Mach number 2.00. The stage was tested with flows at subsonic and supersonic inlet axial Mach numbers and with rotor speeds from 40 to 110 percent of design speed. The fan stage overall performance characteristics, as well as details of its performanc characteristics downstream of the stator vanes, are presented. These measurements were obtained with radially and circumferentially traversing probes. At the design condition, the measured overall pressure ratio was 2.366, and the corresponding adiabatic efficiency was 0.610. Transition from subsonic to supersonic flow was demonstrated at 80, 100 and 110 percent of design speed. At the design condition, the radial distribution of energy addition (temperature ratio) from the computational fluid dynamics (CFD) calculations is in excellent agreement with the measured values. The predicted pressure distributions agree reasonably well with those measured.

Royce D. Moore↗
NASA NTRS1996

Seeding for laser velocimetry in confined supersonic flows with shocks

There is a lack of firm conclusions or recommendations in the open literature to guide laser velocimeter (LV) users in minimizing the uncertainty of LV data acquired in confined supersonic flows with steep velocity gradients. This fact led the NASA Lewis Research Center (LeRC) in Cleveland (Ohio, USA), and the Institute of Propulsion Technology of DLR in Cologne (Germany) to a joint research effort to improve reliability of LV measurements in supersonic flows. Over the years, NASA and DLR have developed different expertise in laser velocimetry, using different LV systems: Doppler and two-spot (L2F). The goal of the joint program is to improve the reliability of LV measurements by comparing results from experiments in confined supersonic flows performed under identical test conditions but using two different LV systems and several seed particle generators. Initial experiments conducted at the NASA LERC are reported in this paper. The experiments were performed in a narrow channel with Mach number 2.5 flow containing an oblique shock wave generated by an immersed 25-dg wedge.

Lepicovsky, J.↗
NASA NTRS1996

Supersonic Laminar Flow Control Research

The objective of this research is to understand supersonic laminar flow stability, transition and active control. Some prediction techniques will be developed or modified to analyze laminar flow stability. The effects of distributed heating and cooling as an active boundary layer control technique will be studied. The primary tasks of the research apply to the NASA/Ames PoC and LFSWT's nozzle design with laminar flow control and are listed as follows: Predictions of supersonic laminar boundary layer stability and transition; Effects of wall heating and cooling on supersonic laminar flow control on a flat plate; Performance evaluation of the PoC and LFSWT nozzle designs with wall heating and cooling applied at different locations and various lengths; Effects of a conducted-vs-pulse wall temperature distribution for the LFSWT; and Application of wall heating and/or cooling to laminar boundary layer and flow separation control of airfoils and investigation of related active control techniques.

Lo, Ching F.↗
NASA NTRS1996

Supersonic Gas-Liquid Cleaning System

The Supersonic Gas-Liquid Cleaning System Research Project consisted mainly of a feasibility study, including theoretical and engineering analysis, of a proof-of-concept prototype of this particular cleaning system developed by NASA-KSC. The cleaning system utilizes gas-liquid supersonic nozzles to generate high impingement velocities at the surface of the device to be cleaned. The cleaning fluid being accelerated to these high velocities may consist of any solvent or liquid, including water. Compressed air or any inert gas is used to provide the conveying medium for the liquid, as well as substantially reduce the total amount of liquid needed to perform adequate surface cleaning and cleanliness verification. This type of aqueous cleaning system is considered to be an excellent way of conducting cleaning and cleanliness verification operations as replacements for the use of CFC 113 which must be discontinued by 1995. To utilize this particular cleaning system in various cleaning applications for both the Space Program and the commercial market, it is essential that the cleaning system, especially the supersonic nozzle, be characterized for such applications. This characterization consisted of performing theoretical and engineering analysis, identifying desirable modifications/extensions to the basic concept, evaluating effects of variations in operating parameters, and optimizing hardware design for specific applications.

Kinney, Frank↗
NASA NTRS1993

Calculations of Supersonic and Hypersonic Flows using Compressible Wall Functions

The present paper presents a numerical procedure to calculate supersonic and hypersonic flows using the compressible law of the wall. The turbulence models under consideration include the Launder-Reece-Rodi-Gibson Reynolds-stress model and the k-epsilon model. The models coupled with the proposed wall function technique have been tested in both separated and unseparated flows. The flows include (1) an insulated flat plate flow over a range of Mach numbers, (2) a Mach 5 flat plate flow with cold wall conditions, (3) a two dimensional supersonic compression corner flow, (4) a hypersonic flow over an axisymmetric flare, and (5) a hypersonic flow over a 2-D compression corner. Results indicate that the wall function technique gives improved predictions of skin friction and heat transfer in separated flows compared with models using wall dampers. Predictions of the extent of separation are not improved over the wall damper models except with the Reynolds-stress model for the supersonic compression corner flow case.

Huang, P. G.↗
NASA NTRS1996

Supersonic Wind Tunnels (Latest Citations from the Aerospace Database)

The bibliography contains citations concerning the design, construction, operation, performance, and use of supersonic wind tunnels. References cover the design of flow nozzles, diffusers, test sections, and ejectors for tunnels driven by compressed air, high-pressure gases, or cryogenic liquids. Methods for flow calibration, boundary layer control, local and freestream turbulence reduction, and force measurement are discussed. Instrusive and non-intrusive instrumentation, sources of measurement error, and measurement corrections are also covered. The citations also include the testing of inlets, nozzles, airfoils, and other components of aerospace vehicles that must operate supersonically. Comprehensive coverage of wind tunnel force balancing systems, and blowdown and supersonic wind tunnels are covered in separate bibliographies.(Contains 50-250 citations and includes a subject term index and title list.)

WIND TUNNELS↗
NASA NTRS1961

Some Effects of Leading-Edge Sweep on Boundary-Layer Transition at Supersonic Speeds

The effects of crossflow and shock strength on transition of the laminar boundary layer behind a swept leading edge have been investigated analytically and with the aid of available experimental data. An approximate method of determining the crossflow Reynolds number on a leading edge of circular cross section at supersonic speeds is presented. The applicability of the critical crossflow criterion described by Owen and Randall for transition on swept wings in subsonic flow was examined for the case of supersonic flow over swept circular cylinders. A wide range of applicability of the subsonic critical values is indicated. The corresponding magnitude of crossflow velocity necessary to cause instability on the surface of a swept wing at supersonic speeds was also calculated and found to be small. The effects of shock strength on transition caused by Tollmien-Schlichting type of instability are discussed briefly. Changes in local Reynolds number, due to shock strength, were found analytically to have considerably more effect on transition caused by Tollmien-Schlichting instability than on transition caused by crossflow instability. Changes in the mechanism controlling transition from Tollmien-Schlichting instability to crossflow instability were found to be possible as a wing is swept back and to result in large reductions in the length of laminar flow.

Chapman, Gray T.↗
NASA NTRS1959

Formulas Pertinent to the Calculation of Flow-Field Effects at Supersonic Speeds Due to Wing Thickness

Expressions based on linearized supersonic-flow theory are derived for the perturbation velocity potential in space due to wing thickness for rectangular wings with biconvex airfoil sections and for arrow, delta, and quadrilateral wings with wedge-type airfoil sections. The complete range of supersonic speeds is considered subject to a minor aspect-ratio-Mach number restriction for the rectangular plan form and to the condition that the trailing edge is supersonic for the sweptback wings. The formulas presented can be utilized in determining the induced-flow characteristics at any point in the field and are readily adaptable for either numerical computation or analytical determination of any velocity components desired.

Margolis, Kenneth↗
NASA NTRS1999

Collective Interaction in a Linear Array of Supersonic Rectangular Jets: A Linear Spatial Instability Study

A linear spatial instability model for multiple spatially periodic supersonic rectangular jets is solved using Floquet-Bloch theory. It is assumed that in the region of interest a coherent wave can propagate. For the case studied large spatial growth rates are found. This work is motivated by an increase in mixing found in experimental measurements of spatially periodic supersonic rectangular jets with phase-locked screech and edge tone feedback locked subsonic jets. The results obtained in this paper suggests that phase-locked screech or edge tones may produce correlated spatially periodic jet flow downstream of the nozzles which creates a large span wise multi-nozzle region where a coherent wave can propagate. The large spatial growth rates for eddies obtained by model calculation herein are related to the increased mixing since eddies are the primary mechanism that transfer energy from the mean flow to the large turbulent structures. Calculations of spacial growth rates will be presented for a set of relative Mach numbers and spacings for which experimental measurements have been made. Calculations of spatial growth rates are presented for relative Mach numbers from 1.25 to 1.75 with ratios of nozzle spacing to nozzle width ratios from s/w(sub N) = 4 to s/w(sub N) = 13.7. The model may be of significant scientific and engineering value in the quest to understand and construct supersonic mixer-ejector nozzles which provide increased mixing and reduced noise.

Miles, Jeffrey Hilton↗
NASA NTRS1965

Effects of the Air Traffic Control System on the Supersonic Transport

A study of the problems anticipated with the introduction of the supersonic transport into the air traffic control system indicated that supersonic transport design allowances for time and fuel for maneuvering during climbouts may not be sufficient, that there is a greater communications-navigation work- load for the supersonic transport than for the subsonic jet transport during descent, and that use of a flight director to command pitch control guidance for the pilot would be helpful.

Norman S. Silsby↗
NASA NTRS1999

Effects of Jet Swirl on Mixing of a Light Gas Jet in a Supersonic Airstream

A non reacting experiment was performed to investigate the effects of jet swirl on mixing of a light gas jet in a supersonic airstream. The experiment consisted of two parts. The first part was an investigation of the effects of jet swirl and skew on the mixing and penetration of a 25 deg. supersonic jet injected from a flat surface (flush wall injection) into a supersonic ducted airflow. Specifically, the objective was to determine whether the jet would mix more rapidly if the jet were swirling, and whether swirl, with and without skew, causes the injectant-air plume to have a net circulation (i.e., a single or dominant vortex). The second part was a preliminary study of the mixing of swirling jets injected from the base of a skewed ramp. The hypothesis was that favorable interactions between vorticity generated by the swirling jet and vortices generated by the ramp could produce mixing enhancements. Both parts of the experiment were conducted at equal injectant mass flow rate and total pressure. The results for the flush wall injection cases indicate that, except relatively close to the injection point, swirl, with or without skew, does not enhance the mixing of the jet, and can in fact reduce penetration. In addition, a plume with significant net circulation is not generated, as had previously been believed. The results for the ramp cases indicated no improvements in mixing in comparison with the baseline (swept ramp injector) case. However, it was not possible to determine the vorticity mechanisms underlying the poor performance, since no measurements of vorticity were made. Thus, since many geometric parameters were chosen arbitrarily, the results are inconclusive for this class of injector.

Doerner, Steven E.↗
NASA NTRS2000

A Qualitative Piloted Evaluation of the Tupolev Tu-144 Supersonic Transport

Two U.S. research pilots evaluated the Tupolev Tu-144 supersonic transport aircraft on three dedicated flights: one subsonic and two supersonic profiles. The flight profiles and maneuvers were developed jointly by Tupolev and U.S. engineers. The vehicle was found to have unique operational and flight characteristics that serve as lessons for designers of future supersonic transport aircraft. Vehicle subsystems and observed characteristics are described as are flight test planning and ground monitoring facilities. Maneuver descriptions and extended pilot narratives for each flight are included as appendices.

Rivers, Robert A.↗
NASA NTRS2000

Longitudinal Handling Qualities of the Tu-144LL Airplane and Comparisons With Other Large, Supersonic Aircraft

Four flights have been conducted using the Tu-144LL supersonic transport aircraft with the dedicated objective of collecting quantitative data and qualitative pilot comments. These data are compared with the following longitudinal flying qualities criteria: Neal-Smith, short-period damping, time delay, control anticipation parameter, phase delay (omega(sp)*T(theta(2))), pitch bandwidth as a function of time delay, and flight path as a function of pitch bandwidth. Determining the applicability of these criteria and gaining insight into the flying qualities of a large, supersonic aircraft are attempted. Where appropriate, YF-12, XB-70, and SR-71 pilot ratings are compared with the Tu-144LL results to aid in the interpretation of the Tu-144LL data and to gain insight into the application of criteria. The data show that approach and landing requirements appear to be applicable to the precision flightpath control required for up-and-away flight of large, supersonic aircraft. The Neal-Smith, control anticipation parameter, and pitch-bandwidth criteria tend to correlate with the pilot comments better than the phase delay criterion, omega(sp)*T(theta(2)). The data indicate that the detrimental flying qualities implication of decoupled pitch-attitude and flightpath responses occurring for high-speed flight may be mitigated by requiring the pilot to close the loop on flightpath or vertical speed.

Cox, Timothy H.↗
NASA NTRS2001

Active Control of Supersonic Impinging Jets

Experimental studies of supersonic impinging jet flows suggest that they are greatly influenced by the flow-acoustic interactions through a feedback mechanism. The self-sustained oscillations of the jet column observed in these flows result in high velocities in the ambient medium induced by the large-scale coherent vortical structures in the jet shear layers. As a consequence, the suck down force on the surface from which the jet is issuing can reach as high as 60% of the primary jet thrust. In addition, the overall sound pressure levels (OASPL) increase significantly relative to a free jet. To alleviate these undesirable flow and acoustic characteristics, a novel control technique using supersonic microjets is demonstrated. Sixteen supersonic microjets are placed around the circumference of the main jet at the nozzle exit to disrupt the feedback mechanism. As a result, significant lift loss recovery (approximately 50%) and reduced near field OASPL (approximately 7 dB) are observed.

Krothapalli, A.↗
NASA NTRS2001

Experimental Investigation of Supersonic Coplanar Jets within Ejectors

This experimental and theoretical work involved reduction of supersonic jet noise using Mach Wave Elimination (MWE), a method that suppresses noise by means of a gaseous layer that envelops the supersonic jet. Also explored was a new method for mixing enhancement in which an axial, secondary flow enhances mixing in a primary flow. The research is relevant to the advent of future supersonic transports that must adhere to the same take-off and landing restrictions as ordinary subsonic aircraft. To reduce noise, one needs to understand the fundamental fluid mechanics of the jet, namely its turbulent structure and mean-flow characteristics, and to perform high-quality noise measurements. The results generated are applicable to free jets as well as to jets within ejectors.

Papamoschou, Dimitri↗
NASA NTRS1994

Sonic and Supersonic Jet Plumes

Study of sonic and supersonic jet plumes are relevant to understanding such phenomenon as jet-noise, plume signatures, and rocket base-heating and radiation. Jet plumes are simple to simulate and yet, have complex flow structures such as Mach disks, triple points, shear-layers, barrel shocks, shock- shear- layer interaction, etc. Experimental and computational simulation of sonic and supersonic jet plumes have been performed for under- and over-expanded, axisymmetric plume conditions. The computational simulation compare very well with the experimental observations of schlieren pictures. Experimental data such as temperature measurements with hot-wire probes are yet to be measured and will be compared with computed values. Extensive analysis of the computational simulations presents a clear picture of how the complex flow structure develops and the conditions under which self-similar flow structures evolve. From the computations, the plume structure can be further classified into many sub-groups. In the proposed paper, detail results from the experimental and computational simulations for single, axisymmetric, under- and over-expanded, sonic and supersonic plumes will be compared and the fluid dynamic aspects of flow structures will be discussed.

Venkatapathy, E.↗
NASA NTRS1994

Experimental and Computational Study of Sonic and Supersonic Jet Plumes

Study of sonic and supersonic jet plumes are relevant to understanding such phenomenon as jet-noise, plume signatures, and rocket base-heating and radiation. Jet plumes are simple to simulate and yet, have complex flow structures such as Mach disks, triple points, shear-layers, barrel shocks, shock-shear-layer interaction, etc. Experimental and computational simulation of sonic and supersonic jet plumes have been performed for under- and over-expanded, axisymmetric plume conditions. The computational simulation compare very well with the experimental observations of schlieren pictures. Experimental data such as temperature measurements with hot-wire probes are yet to be measured and will be compared with computed values. Extensive analysis of the computational simulations presents a clear picture of how the complex flow structure develops and the conditions under which self-similar flow structures evolve. From the computations, the plume structure can be further classified into many sub-groups. In the proposed paper, detail results from the experimental and computational simulations for single, axisymmetric, under- and over-expanded, sonic and supersonic plumes will be compared and the fluid dynamic aspects of flow structures will be discussed.

Venkatapathy, E.↗
NASA NTRS2001

Unsteady Flow in a Supersonic Turbine with Variable Specific Heats

Modern high-work turbines can be compact, transonic, supersonic, counter-rotating, or use a dense drive gas. The vast majority of modern rocket turbine designs fall into these Categories. These turbines usually have large temperature variations across a given stage, and are characterized by large amounts of flow unsteadiness. The flow unsteadiness can have a major impact on the turbine performance and durability. For example, the Space Transportation Main Engine (STME) fuel turbine, a high work, transonic design, was found to have an unsteady inter-row shock which reduced efficiency by 2 points and increased dynamic loading by 24 percent. The Revolutionary Reusable Technology Turbopump (RRTT), which uses full flow oxygen for its drive gas, was found to shed vortices with such energy as to raise serious blade durability concerns. In both cases, the sources of the problems were uncovered (before turbopump testing) with the application of validated, unsteady computational fluid dynamics (CFD) to the designs. In the case of the RRTT and the Alternate Turbopump Development (ATD) turbines, the unsteady CFD codes have been used not just to identify problems, but to guide designs which mitigate problems due to unsteadiness. Using unsteady flow analyses as a part of the design process has led to turbine designs with higher performance (which affects temperature and mass flow rate) and fewer dynamics problems. One of the many assumptions made during the design and analysis of supersonic turbine stages is that the values of the specific heats are constant. In some analyses the value is based on an average of the expected upstream and downstream temperatures. In stages where the temperature can vary by 300 to 500 K, however, the assumption of constant fluid properties may lead to erroneous performance and durability predictions. In this study the suitability of assuming constant specific heats has been investigated by performing three-dimensional unsteady Navier-Stokes simulations for a supersonic turbine stage.

Dorney, Daniel J.↗