SEARCH · Search NASA

Results for “wall modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Dynamic Behavior of Oval-Twisted Helical Tube Heat Exchanger: Numerical Study with RELAP5-3D

Convective heat transfer characteristics and theoretical thermal stress behaviors are numerically calculated using RELAP5-3D for the helical-coiled once-through steam generator (H-OTSG) and the novel heat exchanger design known as the oval-twisted helically coiled heat exchanger (OTHCHX) under (1) fluctuating wall temperature conditions, (2) square-wave pulsating flow conditions, and (3) the combined effects of fluctuating wall temperature and square-wave pulsating flow conditions. Heat transfer coefficient models for the H-OTSG and OTHCHX were developed based on existing data and implemented into RELAP5-3D, successfully capturing the N⁢uavg behavior within 8% to 10% of the reported data. Under fluctuating wall temperature conditions, the OTHCHX displayed higher N⁢u avg behavior than the H-OTSG. As 𝑓 increased, the $𝜎^{𝑚⁢𝑎⁢𝑥}_{𝑡⁢ℎ}$ decreased. The $𝜎^{𝑚⁢𝑎⁢𝑥}_{𝑡⁢ℎ}$ was higher for the OTHCHX than for the H-OTSG under fluctuating wall temperature conditions. Under pulsating flow conditions, the H-OTSG and OTHCHX displayed much higher 𝑁⁢𝑢 𝑎𝑣𝑔 than under constant flow conditions. The H-OTSG displayed a higher $𝜎^{𝑚⁢𝑎⁢𝑥}_{𝑡⁢ℎ}$ over the OTHCHX. Under combined fluctuating wall temperature and pulsating flow conditions, the augmented heat transfer behavior from the pulsating flow was counteracted by the wall temperature fluctuations, producing slightly higher 𝑁⁢𝑢 𝑎𝑣𝑔 over constant wall temperature, constant flow conditions, but much lower than only constant pulsating flow under constant wall temperature conditions. The effects of simultaneous wall temperature fluctuations and square-wave pulsating flow caused higher $𝜎^{𝑚⁢𝑎⁢𝑥}_{𝑡⁢ℎ}$ than that of only wall temperature fluctuations or pulsating flow. As the Reynolds number (Re) increased, $𝜎^{𝑚⁢𝑎⁢𝑥}_{𝑡⁢ℎ}$ increased. However, when 𝑓=𝑓$_{\dot{m}}$, the $𝜎^{𝑚⁢𝑎⁢𝑥}_{𝑡⁢ℎ}$ showed decreasing values as Re increased. In conclusion, the results indicate that thermal-fluid resonance can help mitigate thermal stresses.

Thermal stress↗

DOE OSTI2021

Effects of turbulence-radiation coupling in pressurized oxy-combustion

Concerns over climate change have led to numerous efforts in developing low-carbon energy technologies. Pressurized oxy-combustion (POC) is a promising candidate to reduce carbon emission in power generation. Due to the strong impact of pressure on thermal radiation, heat transfer in POC differs significantly from the situation of conventional atmospheric pressure combustion. Thus thermal radiation in POC needs to be investigated to aid new combustor development. The present computational work is a step in this direction, initiating a systematic analysis of thermal radiation and heat transfer in a pilot-scale POC combustor, which has been developed at Washington University in St. Louis (WUSTL). In a POC process, pulverized coal is burned under elevated pressure and O2-CO2 environment. While most previous computational works on flame radiation focused on atmospheric pressure condition, this work considered a pressurized flame. Specifically, a 15-bar POC combustor of power 50 kW is modeled employing the Ansys FLUENT commercial platform, using both Reynolds-averaged Navier-Stokes (RANS) modeling and large-eddy simulation (LES). A recently published and validated global radiation model is used to predict the radiative property of the flue gas. The discrete ordinates (DO) radiation model is chosen to solve the radiative transport equation. Incident radiation on the walls of the combustor is identified and investigated. It is revealed that for this pilot-scale, pressurized combustor, thermal radiation exhibits similar patterns in the RANS and LES models. However, the magnitudes of radiation are different in both models, presumably because interactions between radiation and turbulence are embedded in the LES model but not in the RANS model. This difference thereby underlines the major goal of this research: investigating the impact of such turbulence-to-radiation coupling on thermal radiation in a pilot-scale POC setting. Most previous studies on turbulence-to-radiation interactions focused on bench-scale, atmospheric pressure flames. This work is the first effort to extend this study to a pilot-scale, pressurized flame.

Li, Lei↗

DOE OSTI2023

Winding θ and destructive interference of instantons

While the θ dependence of field theories is 2π periodic, the ground-state wavefunctions at θ and θ + 2π often belong to different classes of symmetry-protected topological states. When this is the case, a continuous change of the θ parameter can introduce an interface that supports a nontrivial field theory localized on the wall. We consider the 2d CP N-1 sigma model as an example and construct a weak-coupling setup of this interface theory by considering the small S1 compactification with nonzero winding θ parameter and a suitable symmetry-twisted boundary condition. This system has N classical vacua connected by fractional instantons, but the anomaly constraint tells us that the fractional-instanton amplitudes should vanish completely to have N-fold degeneracy at the quantum level. We show how this happens in this purely bosonic system, uncovering that the integration over the zero modes annihilates the fractional instanton amplitudes, in sharp contrast to what happens when the θ angle is constant. Moreover, we provide another explanation of this selection rule by showing that the N perturbative vacua acquire different charges under the global symmetry with the activation of the winding θ angle. We also demonstrate a similar destructive interference between instanton effects in the CP N-1 quantum mechanics with the Berry phase.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2021

Catalyzed baryogenesis

A novel mechanism, “catalyzed baryogenesis”, is proposed to explain the observed baryon asymmetry in our universe. In this mechanism, the motion of a ball-like catalyst provides the necessary out-of-equilibrium condition, its outer wall has CP-violating interactions with the Standard Model particles, and its interior has baryon number violating interactions. We use the electroweak-symmetric ball model as an example of such a catalyst. In this model, electroweak sphalerons inside the ball are active and convert baryons into leptons. The observed baryon number asymmetry can be produced for a light ball mass and a large ball radius. Due to direct detection constraints on relic balls, we consider a scenario in which the balls evaporate, leading to dark radiation at testable levels.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2023

Bridging adsorption behavior of confined CH 4 -CO 2 binary mixtures across scales

An accurate understanding of the competitive adsorption of CH 4 -CO 2 binary mixtures in nano-confined systems is critical for engineering CO 2 storage in shale gas reservoirs. Due to difficulties in making reliable experimental observations in nano-scale, atomistic simulations (ASs), such as the Grand Canonical Monte Carlo (GCMC) method, provide a viable approach to studying the adsorption behavior of confined fluids. ASs are, however, limited in the size of the compositional domain due to the high computational cost. This work proposes a framework that combines AS and the lattice Boltzmann (LB) method to bridge the physics of confined fluids across scales. The Peng–Robinson equation of state (PR-EoS) produces fugacity coefficients, which serve as input for conducting multi-component GCMC simulations. These GCMC simulations explore the competitive adsorption behavior of CH 4 -CO 2 in nano-slits at various composition, pressure, and channel-width conditions. Both components generate adsorption layers with high densities near the walls with CO 2 preferentially adsorbing compared to CH 4 on the organic walls of carbon sheets. At the mesoscale, a pseudopotential model represents the intermolecular forces in multi-component, multiple-relaxation-time LB simulations. The LB simulations are in good agreement with the GCMC results, allowing us to obtain values for tunable LB parameters. We then extend the use of LB to simulate adsorption behavior in complex networks with nano-sized channels. The phase behavior and fluid properties in the complex geometries of nano-channels differ from nano-slits and bulk systems. Furthermore, the bridging of physics from GCMC (microscale) to LB (mesoscale) via the macroscale PR-EoS connects the adsorption behavior of binary systems across scales.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Temperature Homogeneity under Selective and Localized Microwave Heating in Structured Flow Reactors

Selective heating of different phases of multiphase systems via microwaves can result in energy savings and suppression of side reactions. However, materials properties and operating conditions that maximize temperature gradients are poorly understood. Here we utilize computational fluid dynamics (CFD) computations and temperature measurements in structured flow reactors (monoliths) in a monomodal microwave cavity to assess the temperature difference between the walls and the fluid and develop a simple lumped model to estimate when temperature gradients exist. We also explore the material’s thermal and electrical properties of structured reactors for isothermal catalyst conditions. We propose that CFD simulations can be used as a nonintrusive, predictive tool of temperature homogeneity. Importantly, we demonstrate that localized heating in the bed under several conditions rather than selective heating is responsible for the selectivity enhancement. Furthermore, our results indicate that structured beds made of high thermal conductivity materials avoid arcing and enable temperature homogeneity and low electrical conductivity materials allow microwaves to penetrate the domain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Tensor factorization for elucidating mechanisms of piezoresponse relaxation via dynamic Piezoresponse Force Spectroscopy

Spatially resolved time and voltage-dependent polarization dynamics in PbTiO 3 thin films is explored using dynamic piezoresponse force microscopy (D-PFM) in conjunction with interferometric displacement sensing. This approach gives rise to 4D data sets containing information on bias-dependent relaxation dynamics at each spatial location without long-range electrostatic artifacts. To interpret these data sets in the absence of defined physical models, we employ a non-negative tensor factorization method which clearly presents the data as a product of simple behaviors allowing for direct physics interpretation. Correspondingly, we perform phase-field modeling finding the existence of ‘hard’ and ‘soft’ domain wall edges. This approach can be extended to other multidimensional spectroscopies for which even exploratory data analysis leads to unsatisfactory results due to many components in the decomposition.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Stretched exponential magnetic relaxation dynamics in artificial square ice revealed through x-ray photon correlation spectroscopy

X-ray photon correlation scattering measurements are undertaken on a thermally active artificial spin ice based on the square lattice, referred to as artificial square ice, to probe the fluctuation timescales as a function of temperature as the system passes through the paramagnetic-antiferromagnetic phase transition, which belongs to the two-dimensional Ising universality class. In the paramagnetic regime, a single exponential timescale is seen, whereas at and below the critical temperature, a stretched exponential decorrelation is observed, with the stretching exponent decreasing from unity down to below one-half as the temperature reduces. This trend is confirmed by kinetic Monte Carlo simulations of a simplified point-dipolar square ice system, and is in agreement with past theoretical work on the kinetic Ising model where stretched exponential relaxation due to equilibrium domain wall dynamics below the critical temperature was found.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Longitudinal form Factors of A ≤ 10 Nuclei in a Chiral Effective Field Theory Approach

Here, in this work, we present the elastic electron scattering longitudinal form factors of A ≤ 10 nuclei computed in a variational Monte Carlo approach. We employ the Norfolk family of local chiral interactions and a consistent electromagnetic charge operator. Our calculations are compared both to data and past theoretical evaluations. This work represents, to our knowledge, the first accurate calculation of longitudinal form factors using manybody methods based on interacting nucleon degrees of freedom in the 7 ≤ A ≤ 10 mass range. Finally, we identify 9 Be and 10 B as candidate targets for renewed experimental interest, as they exhibit the potential to provide more stringent constraints on the theoretical models.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2023

Effects of baryonic feedback on the cosmic web

Here, we study the effect of baryons on the cosmic web—halos, filaments, walls, and voids. To do so, we apply a modified version of NEXUS, a cosmic web morphological analysis algorithm, to the IllustrisTNG simulations. We find that halos lose more than 10% of their mass due to baryons, mostly to filaments and a small portion to walls and voids. However, the mass transfer does not significantly shift the boundaries of structures, leaving the volume fractions of the cosmic structures largely unaffected. We quantify the effects of baryonic feedback on the power spectrum and the probability density function of the density field for individual cosmic structures. For the power spectrum, most suppression due to feedback can be accounted for by including M ≥ 10 12 M ⊙ /h halos, without considering other cosmic structures. However, when examining the probability density function of the density field, we find nearly 100% suppression of the emptiest regions and 10%-level effects (boost or suppression) in the remaining regions of filaments, walls, and voids. Our results indicate the importance of modeling the effects of baryons in the whole cosmic web, not just halos, for cosmological analysis beyond two-point statistics or field-based inferences.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2024

Measurement-induced phase transition in teleportation and wormholes

We demonstrate that some quantum teleportation protocols exhibit measurement induced phase transitions in Sachdev-Ye-Kitaev model. Namely, Kitaev-Yoshida and Gao-Jafferis-Wall protocols have a phase transition if we apply them at a large projection rate or at a large coupling rate respectively. It is well-known that at small rates they allow teleportation to happen only within a small time-window. We show that at large rates, the system goes into a new steady state, where the teleportation can be performed at any moment. In dual Jackiw-Teitelboim gravity these phase transitions correspond to the formation of an eternal traversable wormhole. In the Kitaev-Yoshida case this novel type of wormhole is supported by continuous projections.

Physics↗

DOE OSTI2022

Impact of Mass Wood Walls on Building Energy Use, Peak Demand, and Thermal Comfort

Thermal mass moderates indoor temperatures, allowing the heating, ventilation, and air conditioning (HVAC) system to operate more efficiently during peak hours. Cross-Laminated Timber (CLT) and other mass wood products provide thermal mass to the building envelope in a lighter and more environmentally friendly form than concrete. However, the influence of CLTs on heating and cooling energy, peak energy demand, and the indoor climate is not well-known. This project was formed to find the energy efficiency benefits of mass timber structures. The objectives were to (1) test the thermal performance of insulated mass wall structures in controlled laboratory conditions, (2) validate simulation models to expand performance to natural climatic conditions, (3) isolate the impact of the thermal properties of wood (thermal mass, thermal conductivity, moisture storage) on heating and cooling energy use and peak energy demand, and to optimize the performance. Currently, the designs used for CLT buildings have focused on structural and fire issues, and they do not consider the thermal mass benefits. Therefore, the thermal performance is not necessarily optimized.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2023

Tech-X contributions to the Center for Tokamak Transients (CTTS) Scientific Discovery through Advanced Computing (SciDAC) project (Final Report)

The Center for Tokamak Transients Simulations (CTTS) consists of computational plasma physicists, computer scientists, and applied mathematicians who are together developing and applying simulation software to improve our understanding of and ability to predict and control transient events in tokamak discharges, particularly those that lead to violent disruptions. We have major simulation activities concerning disruptions that are caused by violating ideal MHD stability criteria, vertical displacement events, resistive wall modes, and tearing modes. We are performing comprehensive modeling of disruption mitigation techniques, particularly by shattered pellet injection (SPI). The Center is built around two mature extended MHD codes: NIMROD and M3D-C1. These codes are being extended in a number of ways as required by the demands of disruption modeling, and are being optimized to work well for larger problem size and modern computer architectures as required to model tokamak plasmas with realistic parameters over the required timescales. The codes will be coupled to the FronTier code for state-of-the-art modeling of SPI. Validation with experimental data on DIII-D, NSTX, and JET is being facilitated by rigorous uncertainty quantification (UQ). The high-level objectives of the center are to: (1) Develop better understanding and improved predictive capability of when crossing a linear stability boundary will likely lead to a disruption, (2) Provide a tool for calculating vessel forces, both axisymmetric and non-axisymmetric, for worst case VDE and other disruptions in tokamaks, (3) Develop increased understanding and improved predictive capability for locked mode disruptions and how best to avoid them, (4) Develop, verify, and validate 3D models for disruption mitigation by shattered pellets that can be used to design and optimize a system for future tokamaks, and (5) Increase the efficiency and scalability of the M3D-C1 and NIMROD codes so that they can model disruptions in ITER scale devices using the most powerful DOE HPC hardware, and (6) Demonstrate code-coupling via FronTier coupling with NIMROD and M3D-C1 and by interfacing these codes within a WDM framework.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

Additive Manufacturing of Leak-Free Metal Components with Thin Walls and Sealing Surfaces

Laser-powder bed fusion (L-PBF) offers the ability to print free form design components which often do not require post-processing. However, challenges arise when printing small geometries with mating surfaces. Using an AddUp FormUp 350 L-PBF machine installed at the Manufacturing Demonstration Facility (MDF) of Oak Ridge National Laboratory (ORNL), a User Agreement project was formed with intent to manufacture metal leak-free cylindrical sealing surfaces. One print of twelve 12.7mm outer diameter (OD) cylinders was designed varying wall thickness in the computer-aided design (CAD) model. A build plate was successfully printed but included two build pauses each adding about five minutes per layer. The build plate of 12 cylinders was removed from the chamber and shipped to the partner.

36 MATERIALS SCIENCE↗

DOE OSTI2026

DEM Modeling and Validation of Pebble Bed Packing Using Chrono::GPU

Accurate prediction of pebble packing structure is important for pebble bed reactors because the spatial distribution of void fraction directly affects coolant flow, pressure drop, heat transfer, and neutronic behavior. However, experimentally validated DEM studies that directly evaluate local void-fraction structure in reactor-relevant pebble beds remain limited. In this work, the pebble bed experiment conducted at Missouri University of Science and Technology is simulated using the graphics processing unit (GPU)-based discrete element method (DEM) code Chrono::GPU. The study focuses on evaluating the ability of Chrono::GPU to reproduce the packing arrangement and void-fraction distribution of a randomly packed spherical pebble bed. The DEM results are first verified against established radial void-fraction correlations, including the Mueller and Vortmeyer-Schuster models, to assess the predicted bulk porosity, near-wall behavior, and oscillatory packing structure. The simulation is then verified against reference DEM data and validated against gamma-ray computed tomography (CT) experimental data at three axial locations. The Chrono::GPU results reproduce the main features of the experimental packing, including the high void fraction near the wall, the first near-wall trough, and the damped oscillatory radial profile caused by wall-induced ordering. Quantitative comparison with DEM data and the CT-based radial profiles shows good agreement, with mean absolute errors on the order of 0.07 and root-mean-square errors below 0.09 for the averaged profiles. These results demonstrate that Chrono::GPU can accurately capture the void-fraction structure of spherical pebble beds and provides a reliable DEM framework for future pebble bed reactor packing, recycling, and thermal-hydraulic studies.

97 - MATHEMATICS AND COMPUTING↗

DOE OSTI2020

Multilevel and multifidelity uncertainty quantification for cardiovascular hemodynamics

Standard approaches for uncertainty quantification in cardiovascular modeling pose challenges due to the large number of uncertain inputs and the significant computational cost of realistic three-dimensional simulations. Here, we propose an efficient uncertainty quantification framework utilizing a multilevel multifidelity Monte Carlo (MLMF) estimator to improve the accuracy of hemodynamic quantities of interest while maintaining reasonable computational cost. This is achieved by leveraging three cardiovascular model fidelities, each with varying spatial resolution to rigorously quantify the variability in hemodynamic outputs. We employ two low-fidelity models (zero- and one-dimensional) to construct several different estimators. Our goal is to investigate and compare the efficiency of estimators built from combinations of these two low-fidelity model alternatives and our high-fidelity three-dimensional models. We demonstrate this framework on healthy and diseased models of aortic and coronary anatomy, including uncertainties in material property and boundary condition parameters. Our goal is to demonstrate that for this application it is possible to accelerate the convergence of the estimators by utilizing a MLMF paradigm. Therefore, we compare our approach to single fidelity Monte Carlo estimators and to a multilevel Monte Carlo approach based only on three-dimensional simulations, but leveraging multiple spatial resolutions. We demonstrate significant, on the order of 10 to 100 times, reduction in total computational cost with the MLMF estimators. We also examine the differing properties of the MLMF estimators in healthy versus diseased models, as well as global versus local quantities of interest. As expected, global quantities such as outlet pressure and flow show larger reductions than local quantities, such as those relating to wall shear stress, as the latter rely more heavily on the highest fidelity model evaluations. Similarly, healthy models show larger reductions than diseased models. In all cases, our workflow coupling Dakota’s MLMF estimators with the SimVascular cardiovascular modeling framework makes uncertainty quantification feasible for constrained computational budgets.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2020

Force Balance Model Assessment for Mechanistic Prediction of Sliding Bubble Velocity in Vertical Subcooled Boiling Flow

The bubble sliding after departing from nucleation site is frequently observed in flow boiling systems and, the crucial impact on wall heat transfer has been evidenced through many experiments. As a result, the heat transfer modeling associated with sliding bubble has become one of the subjects of great attention in CFD boiling heat transfer community. The modeling efforts are primarily aimed at improving the existing Heat Flux Partitioning (HFP) model via the implementation of sliding bubble-induced heat transfer. The performance of HFP model depends inherently on the fidelity of sub-models used to predict the fundamental bubble parameters (e.g., bubble departure/lift-off diameter). In the same context, the accurate prediction of sliding bubble parameters (e.g., sliding bubble growth, sliding bubble velocity) is essential to achieving the successful heat transfer modeling associated with sliding bubble. Of many sliding bubble parameters, this paper deals with the sliding bubble velocity. Specifically, the force balance model was assessed in view of the sliding bubble velocity prediction. The parametric effect of key sub-models (e.g., drag force, bubble growth models) used in the force balance equation was investigated. The experimental data from Maity (2000) and Yoo et al. (2016) were used for demonstrating the model predictive performance. It was found that the force balance model proposed in this study was able to predict well the bubble sliding velocity based on the accurate prediction of bubble growth during sliding. The predictive performance was proven with the experimental data measured under various subcooled boiling conditions of both water and refrigerant (NOVEC-7000) flowing upward in vertical channels.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2021

Numerical investigation of a fueled pre-chamber spark-ignition natural gas engine

Pre-chamber spark-ignition (PCSI) is a leading advanced ignition concept for internal combustion engines with the potential to enable diesel-like efficiency in medium-duty/heavy-duty (MD/HD) natural gas (NG) engines. By leveraging distributed ignition sources from multiple turbulent jets, the PCSI technology can deliver extremely short combustion duration in ultra-lean mixtures and significantly improve the engine thermal efficiency. However, in the automotive industry there is a lack of adequate science base and predictive simulation tools required for commercial development of PCSI engines. Here, in this study, Reynolds-Average Navier-Stokes simulations are carried out to describe the combustion process in lean-burn NG engines, focusing on the combustion modeling approach. Two combustion models, multi-zone well-stirred reactor (MZ-WSR) and G-equation, are used to simulate the combustion process in an MD NG engine equipped with a fueled-PCSI system for four operating conditions close to the lean operating limit. A skeletal chemical mechanism and a laminar flame speed tabulation are used to compute the combustion accurately. Simulation results are compared with experimental data regarding measured cylinder pressure, heat release rate, and combustion duration. By dividing the PCSI combustion process into four distinct phases, the difference between the two models’ results for each phase is analyzed in detail. The MZ-WSR model overestimates the combustion duration for early flame kernel growth in the pre-chamber due to the lack of a specific formulation to take turbulence-chemistry interaction into account. Despite the prolonged combustion duration and low pressure built-up inside the pre-chamber, the model matches the combustion rate in the main-chamber. In contrast, the G-equation model delivers good agreements for the pre-chamber combustion and turbulent jet-driven combustion processes. However, the model starts to underestimate the combustion rate in the main-chamber, especially under ultra-lean mixture conditions. Finally, improvements are needed for both models to simulate the later combustion stage that occurred in the near-wall regions.

33 ADVANCED PROPULSION SYSTEMS↗