Search NASA⌕ Search

SEARCH · Search NASA

Results for “Advanced propellants”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Noise of the 10-bladed, 40 deg swept SR-6 propeller in a wind tunnel

The noise generated by supersonic helical-tip-speed propellers is a likely cabin environment problem for future airplanes powered by these propellers. Three propeller models with different tip sweeps. SR-1M, SR-2, and SR-3, designed for 244 m/sec (800 ft/sec) tip speed at a flight Mach number of 0.8 were previously tested in the NASA Lewis 8- by 6-Foot Wind Tunnel. In order to investigated another design point condition, the SR-6 propeller was designed for 213 m-sec (700 ft/sec) tip speed at a flight Mach number of 0.8. The noise data from this propeller are reported herein. Curves of blade passing frequency noise versus tip Mach number (at constant advance ratio) showed that the SR-6 propeller behaved similarly to the SR-1M propeller. The noise of the SR-6 propeller at its design condition, helical tip Mach number of 1.07, is approximately 3 dB quieter than the SR-2 propeller at its higher design helical tip Mach number of 1.15, but about 2.5 dB noisier than SR-3 at its design condition. The helical tip Mach number shift of the steep noise rise followed the same progression as the blade sweep angle for all of the propellers. When operated at the SR-3 design point, the SR-6 propeller was approximately 1.5 dB quieter than SR-2 and 4 dB noisier than SR-3.

Dittmar, J. H.↗
NASA NTRS1987

Test procedures for detection of in-flight propeller-induced structure-borne noise

A potentially important source of structure-borne interior noise transmission in advanced turboprop aircraft is the impingement of the propeller wake/vortex on downstream aerodynamic surfaces. It can only be safely assumed that this potential source of interior noise may well hold up achievable interior noise levels unless noise control measures are conscientiously incorporated into the aircraft design. Through the use of a laboratory based test apparatus, techniques were developed to estimate the level of in-flight structure-borne noise transmission from combined frequency response function ground testing and in-flight structural response measurements. All phases of the test procedure were simulated in the laboratory and the expected level of accuracy of the procedure is addressed.

Unruh, J. F.↗
NASA NTRS1987

Detection of in-flight propeller-induced structure-borne noise

A potentially important source of structure-borne interior noise transmission in advanced turboprop aircraft is the impingement of the propeller wake/vortex on downstream aerodynamic surfaces. It can be safely assumed that this potential source of interior noise may well adversely affect achievable interior noise levels unless noise control measures are conscientiously incorporated into the aircraft design. Through the use of a laboratory-based test apparatus, techniques were developed to estimate the level of in-flight structure-borne noise transmission from combined frequency response function ground testing and in-flight structural response measurements. All phases of the procedure were simulated in the laboratory and the expected level of accuracy of the procedure is addressed.

Unruh, J. F.↗
NASA NTRS1999

Summary of LO2/Ethanol OMS/RCS Technology and Advanced Development 99-2744

NASA is pursuing non-toxic propellant technologies applicable to RLV and Space Shuttle orbital maneuvering system (OMS) and reaction control system (RCS). The primary objectives of making advancements in an OMS/RCS system are improved safety, reliability, and reduced operations and maintenance cost, while meeting basic operational and performance requirements. An OMS/RCS has a high degree of direct interaction with the vehicle and crew and requires subsystem and components that are compatible with integration into the vehicle with regard to external mold-line, power, and thermal control. In July 1997, a Phase I effort for the technology and advanced development of an upgrade of the space shuttle was conducted to define the system architecture, propellant tank, feed system, RCS thrusters, and OMS engine. Phase I of the project ran from July 1997 to October 1998. Phase II is currently being planned for the development and test of full-scale prototype of the system in 1999 and 2000. The choice of pressure-fed liquid oxygen (LO2) and ethanol is the result of numerous trade studies conducted from 1980 to 1996. Liquid oxygen and ethanol are clean burning, high-density propellants that provide a high degree of commonality with other spacecraft subsystems including life support, power, and thermal control, and with future human exploration and development of space missions. The key to this pressure-fed system is the use of subcooled liquid oxygen at 350 psia. In this approach, there is 80 degrees R of subcooling, which means that boil-off will not occur until the temperature has risen 80 R. The sub-cooling results naturally from loading propellants at 163 R, which is the saturation temperature at 14.7 psia, and then pressurizing to 350 psia on the launch pad. Thermal insulation and conditioning techniques are then used to limit the LO2 temperature to 185 R maximum, and maintain the sub-cooling. The other key is the wide temperature range of ethanol, -173 F to +300 F, which can provide heat to gasify liquid oxygen or provide a good coolant.

Curtis, Leslie A.↗
NASA NTRS1992

ASRM combustion instability studies

The objectives of this task were to measure and compare the combustion response characteristics of the selected propellant formulation for the Space Shuttle Advanced Solid Rocket Motor (ASRM) with those of the current Redesigned Solid Rocket Motor (RSRM) formulation. Tests were also carried out to characterize the combustion response of the selected propellant formulation for the ASRM igniter motor.

Strand, L. D.↗
NASA NTRS1974

Space storable propellant acquisition system

A program was conducted to select the best surface tension propellant acquisition concept for an advanced 3-axis spacecraft propulsion system having 10-year life. Fabricability, performance capability, and spacecraft compatibility of various candidate concepts were assessed and compared. The results showed the sheet-metal vane low-g systems to be preferred for these interplanetary applications. They can be adapted to a broad spectrum of low-g applications and can be tailored to specific missions with the desired operational margin. A preliminary standpipe with vanes design was accomplished based on analysis and testing of the more significant factors influencing fabrication and operation.

Tegart, J. R.↗
NASA NTRS1975

A Study of Gust and Control Response of Model Rotor-Propellers in a Wind Tunnel Airstream

One-ninth-scale model hingeless and gimballed rotor-propellers were tested at an advance ratio of 0.7 in the Wright Brothers Wind Tunnel at MIT, in the presence of sinusoidal longitudinal and vertical gusts produced by a gust generator of novel design. The gimballed rotor was also subjected to sinusoidal collective and cyclic control inputs. Model test data in terms of blade inplane and out-of-plane bending, longitudinal and lateral gimbal motion, wing vertical and chordwise bending, and blade and wing torsion are presented and compared with theory.

Ham, N. D.↗
NASA NTRS1980

General Aviation Propulsion

Programs exploring and demonstrating new technologies in general aviation propulsion are considered. These programs are the quiet, clean, general aviation turbofan (QCGAT) program; the general aviation turbine engine (GATE) study program; the general aviation propeller technology program; and the advanced rotary, diesel, and reciprocating engine programs.

Source record↗
NASA NTRS1987

Research and technology, 1987

Three broad goals were presented by NASA as a guide to meet the challenges of the future: to advance scientific knowledge of the planet Earth, the solar system, and the universe; to expand human presence beyond the Earth into the solar system; and to strengthen aeronautics research and technology. Near-term and new-generation space transportation and propulsion systems are being analyzed that will assure the nation access to and presence in space. Other key advanced studies include large astronomical observatories, space platforms, scientific and commercial payloads, and systems to enhance operations in Earth orbit. Longer-range studies include systems that would allow humans to explore the Moon and Mars during the next century. Research programs, both to support the many space missions studied or managed by the Center and to advance scientific knowledge in selected areas, involve work in the areas of atmospheric science, earth science, space science (including astrophysics and solar, magnetospheric, and atomic physics), and low-gravity science. Programs and experiment design for flights on the Space Station, free-flying satellites, and the Space Shuttle are being planned. To maintain a leadership position in technology, continued advances in liquid and solid propellant engines, materials and processes; electronic, structural, and thermal investigations; and environmental control are required. Progress during the fiscal year 1987 is discussed.

Source record↗
NASA NTRS2004

Cryogenic Fluid Management: 2000-2004

This custom bibliography from the NASA Scientific and Technical Information Program lists a sampling of records found in the NASA Aeronautics and Space Database. The scope of this topic includes cooling technologies for precision astronomical sensors and advanced spacecraft, as well as propellant storage and transfer in space. This area of focus is one of the enabling technologies as defined by NASA's Report of the President's Commission on Implementation of United States Space Exploration Policy, published in June 2004.

Source record↗
NASA NTRS2010

A Heat Transfer Investigation of Liquid and Two-Phase Methane

A heat transfer investigation was conducted for liquid and two-phase methane. The tests were conducted at the NASA Glenn Research Center Heated Tube Facility (HTF) using resistively heated tube sections to simulate conditions encountered in regeneratively cooled rocket engines. This testing is part of NASA s Propulsion and Cryogenics Advanced Development (PCAD) project. Nontoxic propellants, such as liquid oxygen/liquid methane (LO2/LCH4), offer potential benefits in both performance and safety over equivalently sized hypergolic propulsion systems in spacecraft applications. Regeneratively cooled thrust chambers are one solution for high performance, robust LO2/LCH4 engines, but cooling data on methane is limited. Several test runs were conducted using three different diameter Inconel 600 tubes, with nominal inner diameters of 0.0225-, 0.054-, and 0.075-in. The mass flow rate was varied from 0.005 to 0.07 lbm/sec. As the current focus of the PCAD project is on pressure fed engines for LO2/LCH4, the average test section outlet pressures were targeted to be 200 psia or 500 psia. The heat flux was incrementally increased for each test condition while the test section wall temperatures were monitored. A maximum average heat flux of 6.2 Btu/in.2 sec was achieved and, at times, the temperatures of the test sections reached in excess of 1800 R. The primary objective of the tests was to produce heat transfer correlations for methane in the liquid and two-phase regime. For two-phase flow testing, the critical heat flux values were determined where the fluid transitions from nucleate boiling to film boiling. A secondary goal of the testing was to measure system pressure drops in the two-phase regime.

VanNoord, Jonathan↗
NASA NTRS2016

Rocket Propulsion (RP) 21 Steering Committee Meeting - NASA Spacecraft Propulsion Update

Lander Tech is three separate but synergistic efforts: Lunar CATALYST (Lunar Cargo Transportation and Landing by Soft Touchdown) Support U.S. industry led robotic lunar lander development via three public-private efforts. Support U.S. industry led robotic lunar lander development via three public-private partnerships. Infuse or transfer landing technologies into these public private partnerships. Advanced Exploration Systems-Automated Propellant Loading (APL) -Integrated Ground Operations. Demonstrate LH2 zero loss storage, loading and transfer operations via testing on a large scale in a relevant launch vehicle servicing environment. (KSC, GRC). Game Changing Technology-20 Kelvin -20 Watt Cryocooler Development of a Reverse Turbo-Brayton Cryocooler operating at 20 Kelvin with 20 Watts of refrigeration lift.

Propellant↗
NASA NTRSDate not supplied

Addressing CFM Modeling Gaps for Application into NASA’S Future Cutting Edge Missions

NASA, the US industry, and international partners are crafting frameworks to enable sustaining lunar missions. The ongoing programs, led by the agency, and prominent industry players, encompass plans for the sustained use of cryogenic propellants in lunar landers and in-space propellant refueling depots. NASA’s proactive funding initiatives have fueled the advancement of predictive computational models tailored to enhance the storage and transfer of cryogenic propellant. This paper aims to spotlight the latest advancements in this arena and delve into the collaborative efforts surrounding predictive model development within internal NASA programs as well as current and previous collaborations with industry and international partners. The paper presents an overview of recent advancements in cryogenic fluid management model development, along with their correlation with recent microgravity and large-scale cryogenic ground tests. The tests include key experiments such as the ISS Zero-Boil-Off Tank (ZBOT) series of experiments and the (Robotic Refueling Mission 3) RRM3 test during which liquid methane was stored on-orbit for an extended period of five months. The paper also highlights the anchoring of propellant tank pressurized drain tests involving sloshing that were conducted with liquid methane propellant during the Apollo/Saturn Era. Additionally, the paper discusses model anchoring against more recent sloshing tests carried out with liquid hydrogen propellant. Notable large-scale tests, such as a liquid oxygen propellant transfer test conducted by SpaceX were also used to help correlate a two-phase propellant transfer model using the valuable data measured during the test. The paper further showcases model correlations against a substantial oxygen liquefaction test undertaken by NASA to validate In-Situ-Resource-Utilization (ISRU) technologies that will prove pivotal for a sustained lunar presence.

Low-gravity fluid modeling↗
NASA NTRS1981

Application of advanced technologies to derivatives of current small transport aircraft

Mission requirements of the derivative design were the same as the baseline to readily identify the advanced technology benefits achieved. Advanced technologies investigated were in the areas of propulsion, structures and aerodynamics and a direct operating cost benefit analysis conducted to identify the most promising. Engine improvements appear most promising and combined with propeller, airfoil, surface coating and composite advanced technologies give a 21-25 percent DOC savings. A 17 percent higher acquisition cost is offset by a 34 percent savings in fuel used.

Renze, P. P.↗
NASA NTRSDate not supplied

Preliminary Study of Alternative Propellant Performance for a CNTR

Centrifugal Nuclear Thermal Propulsion is an advanced propulsion concept engine which utilizes a bubble through nuclear reactor to directly heat the propellent, containing the liquid fuel in rotating cylinders using centrifugal force. Past studies have almost exclusively focused on hydrogen propellant configurations of the engine with a theoretical performance of 1800 seconds specific impulse. Recent interest in alternative propellants has created a use case for using storable propellants at the cost of lower performance. Most notably ammonia, methane, and propane. The object of this work is to down select viable alternative propellants for use in a CNTR.

Mitchell Schroll↗
NASA NTRS2011

High Power Flex-Propellant Arcjet Performance

A MW-class electrothermal arcjet based on a water-cooled, wall-stabilized, constricted arc discharge configuration was subjected to extensive performance testing using hydrogen and simulated ammonia propellants with the deliberate aim of advancing technology readiness level for potential space propulsion applications. The breadboard design incorporates alternating conductor/insulator wafers to form a discharge barrel enclosure with a 2.5-cm internal bore diameter and an overall length of approximately 1 meter. Swirling propellant flow is introduced into the barrel, and a DC arc discharge mode is established between a backplate tungsten cathode button and a downstream ringanode/ spin-coil assembly. The arc-heated propellant then enters a short mixing plenum and is accelerated through a converging-diverging graphite nozzle. This innovative design configuration differs substantially from conventional arcjet thrusters, in which the throat functions as constrictor and the expansion nozzle serves as the anode, and permits the attainment of an equilibrium sonic throat (EST) condition. During the test program, applied electrical input power was varied between 0.5-1 MW with hydrogen and simulated ammonia flow rates in the range of 4-12 g/s and 15-35 g/s, respectively. The ranges of investigated specific input energy therefore fell between 50-250 MJ/kg for hydrogen and 10-60 MJ/kg for ammonia. In both cases, observed arc efficiencies were between 40-60 percent as determined via a simple heat balance method based on electrical input power and coolant water calorimeter measurements. These experimental results were found to be in excellent agreement with theoretical chemical equilibrium predictions, thereby validating the EST assumption and enabling the utilization of standard TDK nozzle expansion analyses to reliably infer baseline thruster performance characteristics. Inferred specific impulse performance accounting for recombination kinetics during the expansion process implied nearly frozen flow in the nozzle and yielded performance ranges of 800-1100 sec for hydrogen and 400-600 sec for ammonia. Inferred thrust-to-power ratios were in the range of 30-10 lbf/MWe for hydrogen and 60-20 lbf/MWe for ammonia. Successful completion of this test series represents a fundamental milestone in the progression of high power arcjet technology, and it is hoped that the results may serve as a reliable touchstone for the future development of MW-class regeneratively-cooled flex-propellant plasma rockets.

Litchford, Ron J.↗
NASA NTRS1989

An Approximate Model for the Performance and Acoustic Predictions of Counterrotating Propeller Configurations

An approximate method was developed to analyze and predict the acoustics of a counterrotating propeller configuration. The method employs the analytical techniques of Lock and Theodorsen as described by Davidson to predict the steady performance of a counterrotating configuration. Then, a modification of the method of Lesieutre is used to predict the unsteady forces on the blades. Finally, the steady and unsteady loads are used in the numerical method of Succi to predict the unsteady acoustics of the propeller. The numerical results are compared with experimental acoustic measurements of a counterrotating propeller configuration by Gazzaniga operating under several combinations of advance ratio, blade pitch, and number of blades. In addition, a constant-speed commuter-class propeller configuration was designed with the Davidson method and the acoustics analyzed at three advance ratios. Noise levels and frequency spectra were calculated at a number of locations around the configuration. The directivity patterns of the harmonics in both the horizontal and vertical planes were examined, with the conclusion that the noise levels of the even harmonics are relatively independent of direction whereas the noise levels of the odd harmonics are extremely dependent on azimuthal direction in the horizontal plane. The equations of Succi are examined to explain this behavior.

Denner, Brett William↗