Search NASA⌕ Search

SEARCH · Search NASA

Results for “Atomic Force Microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Effect of plasma treatment on LMPAEK/CF tape and composites manufactured by automated tape placement (ATP)

Automated tape placement (ATP) process is widely used in aerospace for its advanced process control and multi-axis capabilities but faces issues like limited choice of materials and suboptimal tape consolidation. This study investigates air plasma treatment on ATP carbon fiber thermoplastic feedstock tape to address these challenges. The effects on low melt Polyaryletherketone/carbon fiber unidirectional tape (LMPAEK/CF UD tape) were analyzed. Treated and untreated tapes were used to fabricate composites and evaluated for physical, thermal, mechanical, and interfacial properties. Atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) analyses revealed surface roughness changes (on LMPAEK), extent of oxidation, and the presence of hydroxyl/carboxyl groups. Composites from plasma-treated tapes showed a 7.6% increase in tensile strength, 8% in tensile modulus, 18% in flexural strength, and 8.3% in flexural modulus. Further, the interlaminar shear strength improved by 18.7%. Failure analysis showed untreated composites failed via inter-ply and fiber-matrix delamination, while treated composites experienced matrix cracking and fiber breakage. This study highlights atmospheric plasma treatment as a solution to ATP’s limitations, significantly enhancing LMPAEK/CF UD tape composites’ properties.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Alteration of pool boiling heat transfer on metallic surfaces by in situ oxidation

The critical heat flux during pool boiling has been investigated for a range of applications including electrical power generation and thermal management. Reported experimental CHF values during pool boiling of water on flat metallic surfaces, however, show a large discrepancy across studies. Here, we address this discrepancy in CHF values by accounting for oxidation of metallic surfaces during boiling. We studied the effect of in situ oxidation on flat Cu and Ni surfaces by changing the duration that samples were held in saturated water before conducting boiling experiments. The morphology and chemical composition of surfaces after the boiling experiments were analyzed by atomic force microscopy and X-ray photoelectron spectroscopy, respectively. Cu surfaces showed gradually increasing CHF values as the duration in saturated water increased, which could be attributed to the increase in roughness due to the formation of Cu 2 O nanostructures. Conversely, Ni surfaces showed relatively stable CHF and morphology as a nearly flat layer of NiO formed, with one exception: formation of a highly wetting hydroxide, Ni(OH) 2 , on a Ni coupon held in saturated water for 24 h resulted in a uniquely high CHF value, signifying the importance of surface chemistry in addition to morphology. Finally, the fundamental mechanisms resulting in the wide spread of CHF values on metallic surfaces elucidated in this work will lead to more accurate estimation of CHF as well as a deeper mechanistic understanding of CHF values on engineered surfaces.

42 ENGINEERING↗
DOE OSTI2024

Hydrogen effects on the deformation and slip localization in a single crystal austenitic stainless steel

Hydrogen is known to embrittle austenitic stainless steels, which are widely used in high-pressure hydrogen storage and delivery systems, but the mechanisms that lead to such material degradation are still being elucidated. The current work investigates the deformation behavior of single crystal austenitic stainless steel 316L through combined uniaxial tensile testing, characterization and atomistic simulations. Thermally precharged hydrogen is shown to increase the critical resolved shear stress (CRSS) without previously reported deviations from Schmid’s law. Molecular dynamics simulations further expose the statistical nature of the hydrogen and vacancy contributions to the CRSS in the presence of alloying. Slip distribution quantification over large in-plane distances (> 1 mm), achieved via atomic force microscopy (AFM), highlights the role of hydrogen increasing the degree of slip localization in both single and multiple slip configurations. The most active slip bands accumulate significantly more deformation in hydrogen precharged specimens, with potential implications for damage nucleation. For $\langle$110$\rangle$ tensile loading, slip localization further enhances the activity of secondary slip, increases the density of geometrically necessary dislocations and leads to a distinct lattice rotation behavior compared to hydrogen-free specimens, as evidenced by electron backscatter diffraction (EBSD) maps. Finally, the results of this study provide a more comprehensive picture of the deformation aspect of hydrogen embrittlement in austenitic stainless steels.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tracking the phase changes in micelle-based NiGa nanocatalysts for methanol synthesis under activation and working conditions

The hydrogenation of CO 2 into high energy density fuels such as methanol, where the required H 2 is obtained from renewable sources, is of utmost importance for a sustainable society. In recent years, NiGa alloys have attracted attention as promising catalyst material systems for the hydrogenation of CO 2 into methanol at ambient pressures. They thus represent an energy-saving alternative to the Cu-based catalysts employed in today's catalytic industry that require high pressures for the CO 2 hydrogenation. However, the underlying reaction mechanisms for the NiGa system are still under debate. One of the challenges here is to unravel the evolution and coexistence of the different species in the heterogeneous NiGa catalyst system under activation and reaction conditions. To shed light on their evolution under activation in H 2 and their catalytic roles under CO 2 hydrogenation working conditions on well-defined Ni 3 Ga 1 and Ni 5 Ga 3 nanoparticle (NP) catalysts, we employed a multi-probe approach in this study. It included advanced machine learning-based analysis of operando X-ray absorption spectroscopy data combined with operando powder X-ray diffraction and near ambient pressure X-ray photoelectron spectroscopy measurements, as well as reactivity studies using bed-packed mass flow reactors. In addition, we employed atomic force microscopy and scanning transmission electron microscopy for structural characterization. Under H 2 activation at 1 bar total pressure, we concluded the formation of metallic Ni, starting for Ni 3 Ga 1 at 300 °C, and for Ni 5 Ga 3 at 400 °C. At higher temperatures, the formation of NiGa alloys follows. The α'-Ni 3 Ga 1 alloy phase is predominantly formed for the Ni 3 Ga 1 NPs, while the coexistence of α'-Ni 3 Ga 1 , δ-Ni 5 Ga 3 and Ga 2 O 3 phases is observed for the Ni 5 Ga 3 NPs after the H 2 activation. The formation of the Ga 2 O 3 phase also results in the presence of excess metallic Ni. Under CO 2 hydrogenation reaction conditions, Ga partially oxidizes again to form a Ga 2 O 3 -rich particle shell for both NP compositions, yet, to a larger extent for the Ni 3 Ga 1 NPs, which, in turn, feature a higher amount of excess Ni. We reveal that metallic Ni is responsible for the high selectivity of the Ni 3 Ga 1 NPs towards the production of methane in our catalytic tests. In contrast, the Ni 5 Ga 3 NPs display a strong selectivity toward methanol production (>92%), more than one order of magnitude higher than that for the Ni 3 Ga 1 NPs, which we ascribe to the presence of the δ-Ni 5 Ga 3 phase.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Vibrational sum frequency generation spectroscopy reveals the inertness of chromium oxide (001) surfaces

Nanoengineered metal oxides such as Cr(III)-oxide (chromia) films have diverse potential applications in corrosion inhibition, remediation, energy generation, catalysis, data storage, and biological and environmental systems. Concerns about material degradation or oxidation to toxic chromate necessitate an understanding of chromia/aqueous interfaces, beginning with their hydroxylation and hydration behavior. Vibrational sum-frequency generation spectroscopy (vSFG) provides specific molecular-level information about water at the oxide/aqueous junction with high surface selectivity. To overcome the strong absorber problem typical of certain metal oxides in the UV–visible range during nonlinear optical studies, we employed molecular beam epitaxy to deposit transparent, epitaxial nanofilms of Cr 2 O 3 with (001) crystalline orientation on sapphire (Al 2 O 3 (001)) substrates, as confirmed by atomic force microscopy and X-ray diffraction. vSFG spectra of the air and water interfaces of the Cr 2 O 3 (001) films reveal hydroxyl features corresponding to both dissociated and molecular water on the surface. In contrast to the dangling hydroxyls found on the bare Al 2 O 3 (001) substrate, the hydroxyl groups on the deposited Cr 2 O 3 (001) nanofilm do not readily undergo isotopic H/D exchange when exposed to varying forms of D 2 O under ambient conditions. When considering the chemistries of the corresponding trivalent cations in aqueous solution, the finding is at variance with their similar acidities and proton exchange dynamics but consistent with markedly slower inner-sphere water ligand exchange of hexaquo Cr 3+ . This finding challenges the idea that proton and water exchange at the water/Cr₂O₃(001) interface are solely correlated, driven by the strength of metal-bridging oxygen bonds and surface hydroxyl distribution, without direct causation.

Boamah-Agyemang, Mavis D. [Pacific Northwest Natio↗
DOE OSTI2026

Lattice-scale variations in viscosity are correlated with solution structure at mineral-water interfaces

At solid-liquid interfaces, the viscosity increases markedly from the bulk due to the collective interactions of ions and water molecules, influencing phenomena relevant to nanofluidics, colloidal dynamics, and electrochemistry. Here, in this study, we investigated dissipative forces at the boehmite-water interface using 3D atomic force microscopy. We observed an increase in interfacial solution viscosity, η, by 10-100-fold as the nanoprobe approached the surface in normal direction, with up to four oscillatory features showing average peaks of η/η bulk = 44-71. Moreover, the viscosity showed sub-nanometer variations within 0.5 nm from the interface, templated by the underlying crystal lattice and correlated with the interfacial solution structure. Beyond a near-wall region of approximately 1.2 nm, the dissipative response was comparable to that in bulk solution. Molecular dynamics simulations, along with statistical mechanical analyses, provided details on hydrodynamic structures near the interface. Specifically, the lattice-dependent dissipative responses are correlated with extensive hydrogen bonding by interfacial water molecules, which increased friction, particularly along the [001] direction. These results demonstrate how solution viscosity at mineral-water interfaces is anisotropic and correlated with the local solution structure, providing insights into the dynamics of nanocrystal attachment.

Viscosity↗
DOE OSTI2020

Homoepitaxial growth of 9,10-diphenylanthracene

Organic single crystals are often shown to have significantly improved optoelectronic properties over polycrystalline thin films such as exciton diffusivity and carrier mobility. There is growing interest in incorporating such crystals in organic electronics despite a number of challenges. In this work, the homoepitaxial vapor phase growth modes for 9,10-diphenylanthracene (DPA) homoepitaxy are mapped as a function of growth rate and temperature using in situ ultra-low current reflection high energy electron diffraction (RHEED), X-ray diffraction (XRD), and atomic force microscopy (AFM). Vapor phase deposition was performed on free-standing single crystal DPA substrates, which show clear Kikuchi patterns. At room temperature, a transition from Frank-Van der Merwe layer-by-layer growth to step-flow growth is observed as the deposition rate is decreased, while at lower temperatures a Stranski-Krastanov layer-plus-island growth is observed. This is the first demonstration of true step-flow growth from room temperature vapor phase deposition for organic semiconductors and is reminiscent of traditional semiconductor growth regimes. Accordingly, these results could lead to improved control over growth and doping of organic single crystals, and lead to enhanced single crystal organic optoelectronic applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

A statistical mechanics framework for polymer chain scission, based on the concepts of distorted bond potential and asymptotic matching

To design increasingly tough, resilient, and fatigue-resistant elastomers and hydrogels, the relationship between controllable network parameters at the molecular level (bond type, non-uniform chain length, entanglement density, etc.) to macroscopic quantities that govern damage and failure must be established. Many of the most successful constitutive models for elastomers have been rooted in statistical mechanical treatments of polymer chains. Typically, such constitutive models have used variants of the freely jointed chain model with rigid links. However, since the free energy state of a polymer chain is dominated by enthalpic bond distortion effects as the chain approaches its rupture point, bond extensibility ought to be accounted for if the model is intended to capture chain rupture. To that end, a new bond potential is supplemented to the freely jointed chain model (as derived in the u FJC framework of Buche and Silberstein (2021) and Buche et al. (2022)), which we have extended to yield a tractable, closed-form model of single chain behavior that should be amenable to continuum-level constitutive model development. Inspired by the asymptotically matched u FJC model response in both the low/intermediate chain force and high chain force regimes, a simple, quasi-polynomial bond potential energy function is derived. This bond potential exhibits harmonic behavior near the equilibrium state and anharmonic behavior for large bond stretches tending to a characteristic energy plateau (akin to the Lennard-Jones and Morse bond potentials). Using this bond potential, approximate yet highly-accurate analytical functions for bond stretch and chain force dependent upon chain stretch are established. Then, using this polymer chain model, a stochastic thermal fluctuation-driven chain rupture framework is developed. This framework is based upon a force-modified tilted bond potential that accounts for distortional bond potential energy, allowing for the derivation and subsequent calculation of the dissipated chain scission energy. Here, the cases of rate-dependent and rate-independent scission are accounted for throughout the rupture framework. The impact of Kuhn segment number on chain rupture behavior is also investigated. The model is fit to single chain mechanical response data collected from atomic force microscopy tensile tests for validation and to glean deeper insight into the molecular physics taking place. Due to their analytical nature, this polymer chain model and the associated rupture framework can in the future be implemented in finite element models accounting for fracture and fatigue in polydisperse elastomer networks.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mechanical and chemical properties of PVD and cold spray Cr-coatings on Zircaloy-4

In this paper, accident-tolerant fuel (ATF) cladding materials aim to improve fuel reliability and safety during accident scenarios in water-cooled reactors. These ATF cladding should also perform comparable or better than the current zirconium alloy cladding under reactor normal operating conditions. Surface-modified Zircaloy-4 was produced by depositing a protective coating of chromium by two different coating techniques, Physical Vapor Deposition (PVD) and Cold Spray (CS). The coating thickness, structure, composition, and mechanical properties of the coated Zircaloy were assessed with advanced materials characterization techniques. Results showed a strengthening effect of the Cr-coating, along with ~83% higher hardness compared to that of the Zircaloy-4 substrate. Surface topography and surface chemistry of the Cr-coated Zircaloy-4 were assessed with contact profilometry, atomic force microscopy, contact angle goniometry, and X-ray photoelectron spectroscopy. Deposited Cr-coating significantly improved surface wettability compared to the substrate Zircaloy-4. The formation of surface oxides on the coatings by prolonged exposure to ambient air showed a further increase in the hydrophobic behavior. Surface parameters and surface chemistry after flow boiling critical heat flux tests, conducted at atmospheric pressure, evidenced a slight increase in surface roughness with notable changes in wettability associated with the formation of surface oxides.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of Added Gadolinium Oxide on the Thermal Air Oxidation of Uranium Dioxide

To develop a more reliable and stable UO2-based nuclear fuel, the Pacific Northwest National Laboratory (PNNL) investigated modifying fuel with several soluble lanthanides and zirconium. This article provides the results of these studies investigating gadolinium doping at levels up to 10 mass%. The authors characterized and compared commercially- and PNNL-prepared gadolinium-doped UO2 to determine the oxygen-to-metal ratio, elemental distribution, chemical composition, physical appearance, lattice parameters, and grain structure using atomic force microscopy, scanning electron microscopy coupled with energy dispersive spectroscopy, and X-ray diffractometry. After confirming PNNL-prepared UO2 and (Gd,U)O2 were similar to commercially prepared UO2 and (Gd,U)O2, we measured the thermal behavior of these gadolinium-doped UO2 materials to air oxidation using differential scanning calorimetry and thermogravimetric analysis. Addition of gadolinium stabilized the first oxidation product U4¬O9/U3O7 and slowed the subsequent oxidation to U3O8. Comparison of our measured two-step oxidation of UO2 to U3O8 at 325°C to common gas/solid kinetic reaction models found that each oxidation step is best described as a convolution of kinetic behaviors; the gadolinium insertion into the UO2 lattice enforces a significant alteration in mechanism and oxidation rate. Noticeable changes in mechanism become apparent between 1% and 3% gadolinium content.

Uranium Dioxide, Gadolinium Oxide, Thermal Air Oxi↗
DOE OSTI2024

Radiation damage study of POCO ZXF-5Q graphite for neutrino production targets using 4.5 MeV helium ions

To address the challenges of increased beam power and target survivability associated with next-generation particle production beam lines, high dose, high-energy proton beam conditions are simulated using irradiation from low-energy ion beams. A low-energy ion irradiation study of POCO ZXF-5Q graphite under conditions similar to those of the NuMI NT-02 neutrino production target at the Fermi National Accelerator Laboratory is reported. Helium ion irradiation was performed at 100 ∘ C to a maximum damage level of 0.9 displacements per atom (DPA). Irradiation induced hardening, swelling of the irradiated region, inter-plane lattice expansion, and intraplane lattice contraction with increasing ion fluence was observed using micromechanical (nanoindentation, atomic force microscopy) and electron microscopy (high-resolution imaging, selected area diffraction) characterization. Similar changes were also observed in post irradiation examination of the NT-02 target indicating that ion irradiation can be a valuable tool for estimating radiation damage in proton beam targets. Caution must be exercised though, because the hardening, lattice alteration, and swelling occur to different magnitudes for a given damage level. The observed hardening and embrittlement were greater for ion irradiated graphite. For He ion irradiated samples the lattice spacing changes were smaller at low damage levels (78% less expansion and 71% less contraction at 0.1 DPA) and larger at high damage levels (38% more expansion and 5% more contraction at 0.9 DPA) relative to that observed in the NT-02 target. The magnitude of swelling was 8.5× greater under ion irradiation which is influenced by the differing damage gradients and inclusion of implanted He ions in the region of interest.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Reticular chemistry for the rational design of mechanically robust mesoporous merged-net metal-organic frameworks

Access to metal-organic frameworks (MOFs) with enhanced mechanical stability is key to their successful deployment in practical applications. However, the high porosity of the material often affects mechanical stability. In this article, to achieve highly porous MOFs with enhanced mechanical stability, we explored the merged-net approach where two relatively fragile frameworks were merged into a robust MOF structure. We demonstrate the effectiveness of this approach by computationally evaluating mechanical properties of sph-MOFs with varying lengths of linkers. Prominently, we pinpoint the significance of triangular rigidity on the robustness of large-pore MOFs and, subsequently, designed and synthesized a rare earth (RE)-based RE-sph-MOF-5 by the reticulation of hexanuclear RE clusters, tritopic linkers, and unprecedentedly large planar hexatopic linkers containing 19 phenyl rings. The mechanical properties of sph-MOFs were characterized and quantified using amplitude-frequency modulation (AM-FM) bimodal atomic force microscopy (AFM) analyses. Markedly, the mesoporous RE-sph-MOF-5 expresses high mechanical stability despite its large mesoporous cavities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Recent advances in the mechanical characterization of shales at nano-to micro-scales: A review

Understanding geomechanical properties of shales, such as stiffness properties and fracture toughness, is important in different areas of petroleum industry-related activities. Nanoscale to microscale experiments on shale samples require a much smaller sample compared to macroscale experiments. This is a major advantage because irregularly-shaped drill cuttings from shales can be used for experimental analyses, such as nanoindentation or atomic force microscopy (AFM). However, characterization of mechanical properties at the nano- to micro-scale is a relatively new addition to classical geomechanical experiments on shales, and there is still a lack of both fundamental knowledge and standard procedures for conducting experiments at this scale. The theoretical principles of nanoindentation-based (Gridded Nanoindentation and Modulus Mapping) and AFM-based experimental methods (PeakForce QNMTM and AFM-IR), a review of the literature results and the major findings are explained in Sections 2 and 3, respectively. These experimental techniques are compared in Section 4. Overall, nanoindentation experiments reveal the anisotropy of organic matter (OM)-rich shales at the nanoscale, and it is shown that gridded nanoindentation is capable of characterizing different minerals with respect to their stiffness properties. The capability of AFM (PeakForce QNMTM) to differentiate between different minerals within OM-rich shales with distinct mechanical properties, in particular stiffness, is also demonstrated. It is shown that AFM-based methods are more straightforward than gridded-nanoindentation to characterize OM-rich shales based on the stiffness of different constituent minerals of OM-rich shales, but nanoindentation can apply higher loads than AFM-based methods. Therefore, they can measure creep properties and fracture toughness of OM-rich shales. Here, it is shown that the OM is the most compliant part of the OM-rich shales, but it is still unclear if thermal maturation has an impact on the stiffness of OM. It is necessary to investigate if there is a relationship between the OM type (kerogen, bitumen, etc.) and mechanical properties such as Young’s modulus and Creep rate.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High-performance multiblock PEMs containing a highly acidic fluorinated-hydrophilic domain for water electrolysis

The present paper describes the design and evaluation of novel hydrophilic–hydrophobic poly(arylene ether sulfone) (PAES) multiblock copolymers for their synergistic effects upon transport properties and their potential use in proton exchange membrane water electrolysis. The multiblock copolymers are prepared via a coupling reaction between (i) a hydrophilic segment consisting of a disulfonated quinone fluorinated biphenyl group that contains fluorine moieties next to the sulfonated groups to increase the acidity, and (ii) hydrophobic segments composed of non-sulfonated biphenyl sulfone to provide dimensional stability. Two different lengths (molecular weights; 5k and 10k, where k represents 10 3 g mol -1 ) of hydrophobic segments are used to investigate the effects of the membrane properties compared with those of Nafion® and PAES random copolymer (i.e., BPSH40). Atomic force microscopy images of the BPSH40 and multiblock membranes are shown to agree closely with a mesoscale simulation, thus confirming the importance of the morphological effect upon the transport properties. Furthermore, the multiblock copolymer with a higher proportion of hydrophilic segments (10 k–5k) was shown to provide enhanced performance (3.41 A cm -2 at 1.9 V) compared to the multiblock copolymer with equal proportions of hydrophilic and hydrophobic segments (10 k–10 k) due to the greater continuity of nano-sized ionic channels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

A strategy to eliminate selenium oxide islands formed on the ZnSe/GaAs epilayer

Atomically clean and smooth surfaces are essential for semiconductor device fabrication and epitaxial regrowth. In this regard, spontaneously formed oxide islands or clusters on the surfaces of II-VI semiconductor exposures to air can disrupt interface formation. Using ZnSe/GaAs heterostructures grown by molecular beam epitaxy (MBE), we investigated the effect of surface treatments in eliminating oxide islands. The samples were probed with atomic force microscopy, low-temperature photoluminescence, and scanning electron microscopy. Here, it was found that ultra-high vacuum (UHV) annealing at 200°C, regardless of annealing duration, largely removed the islands while leaving the crystallinity of the ZnSe and GaAs epilayers unaffected. UHV annealing at higher temperatures of 300°C completely removed the islands, but the optical properties of ZnSe and/or GaAs epilayers deteriorated depending on the annealing duration. Our observations provide guidance to set thermal annealing strategies for removing oxide islands from the surfaces of II-VI/III-V semiconductor heterostructures depending on the desired properties.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Improvement of interfacial adhesion of unidirectional textile grade carbon fiber (TCF) with unsized, epoxy and urethane sizing reinforced in thermoset urethane composites

This work considers a unique wide tow (450k filaments) form of low-cost carbon fiber intended for non-aerospace applications. TCF is currently produced in epoxy and urethane sizing, and there is a need to understand its resulting composite properties. In this work, the interfacial adhesion of sized TCF reinforced in thermoset urethane (TSU) composites are examined through the surface, thermal and mechanical characterization techniques. Atomic force microscopy (AFM) results showed an increase in surface roughness for urethane (276%) and epoxy sized (78%) versus unsized TCF. XPS results showed 531% increase in O in epoxy sized TCF and 250% N content in urethane sized TCF compared to unsized TCF. The surface energy of epoxy and urethane sized TCF is enhanced by 78% and 96%, respectively compared to unsized TCF. The storage modulus showed improvement for urethane (23%) and epoxy (21%) sized than unsized TCF-TSU composites. The flexural, interlaminar shear strength (ILSS), and impact properties of urethane sized TCF increase by 24%, 50%, and 273%, respectively, than unsized TCF. The results demonstrate that the surface and thermal properties correlate with the mechanical properties of TCF-TSU composites and sizing enhances the wettability of the composites.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ultra-efficient polymer binder for silicon anode in high-capacity lithium-ion batteries

As a highly promising anode material for high-capacity lithium-ion batteries (LIBs), the low electronic conductivity and large volume variation of silicon (Si) make the slurry-coating Si based electrode requiring high content of “inert” materials and suffering rapid capacity fading. In this work, a polyimine, synthesized via one-step condensation reaction, has been demonstrated as an ultra-efficient polymer binder that can resolve the above issues. The polyimine binder containing Si electrode delivers superior electrochemical performance: a delithiation specific capacity of 804.4 mAh g –1 with capacity retention of 82.4% after 1000 cycles at the current density of 2 A g –1 . The high efficiency of polyimine binder for Si electrode has also been demonstrated with ultrahigh weight ratio of “active” material to “inert” material (R A/I ). The electrode with 95 wt% of Si (95Si/Polyimine, R A/I = 19) reveals a reversible delithiation capacity of 2114 mAh g –1 (capacity retention ~ 80.4%) over 200 cycles at the current density of 400 mA g –1 . Even at the high current density of 2 A g –1 , a delithiation capacity of 1087.8 mAh g –1 after 500 cycles can be obtained. Molecular simulations and atomic force microscopy (AFM) indentation are utilized to investigate the ultra-efficiency of polyimine binder. With simple manufacturing process and ultra-efficient binder performance, the designed polyimine binder will be definitely meaningful in achieving low-cost and high-capacity LIBs with prolonged cycle life.

25 ENERGY STORAGE↗
DOE OSTI2020

Selective patterning of out-of-plane piezoelectricity in MoTe 2 via focused ion beam

Two-dimensional transition-metal dichalcogenides (TMDs) have a strain-sensitive nature and can only exhibit in-plane piezoelectricity, owing to their in-plane inversion symmetry breaking, which limits their practical applications for vertical stimulations. Here, we demonstrated the capability of focused ion beams to create out-of-plane piezoelectricity on multi-layered MoTe 2 . We utilized a focused helium ion beam to selectively pattern the out-of-plane piezoelectricity via defect engineering in a layered MoTe 2 flake. The generated out-of-plane piezoelectricity in the desired area was quantitatively examined using atomic force microscopy, and ion beam irradiation-induced defect formation that gave rise to inversion symmetry breaking was confirmed. These results indicated that the out-of-plane piezoelectricity can be selectively patterned through a focused helium ion beam, and it is expected that this approach can also be applied to other classes of TMDs and can expand the application fields of TMD-based devices.

36 MATERIALS SCIENCE↗