Search NASA⌕ Search

SEARCH · Search NASA

Results for “Compression Ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Numerical simulation of the flow and fuel-air mixing in an axisymmetric piston-cylinder arrangement

The implicit factored method of Beam and Warming was employed to describe the flow and the fuel-air mixing in an axisymmetric piston-cylinder configuration during the intake and compression strokes. The governing equations were established on the basis of laminar flow. The increased mixing due to turbulence was simulated by appropriately chosen effective transport properties. Calculations were performed for single-component gases and for two-component gases and for two-component gas mixtures. The flow field was calculated as functions of time and position for different geometries, piston speeds, intake-charge-to-residual-gas-pressure ratios, and species mass fractions of the intake charge. Results are presented in graphical form which show the formation, growth, and break-up of those vortices which form during the intake stroke and the mixing of fuel and air throughout the intake and compression strokes. It is shown that at bore-to-stroke ratio of less than unity, the vortices may break-up during the intake stroke. It is also shown that vortices which do not break-up during the intake stroke coalesce during the compression stroke. The results generated were compared to existing numerical solutions and to available experimental data.

Shih, T. I. P.↗
NASA NTRS1973

Local flow measurements at the inlet spike tip of a Mach 3 supersonic cruise airplane

The flow field at the left inlet spike tip of a YF-12A airplane was examined using at 26 deg included angle conical flow sensor to obtain measurements at free-stream Mach numbers from 1.6 to 3.0. Local flow angularity, Mach number, impact pressure, and mass flow were determined and compared with free-stream values. Local flow changes occurred at the same time as free-stream changes. The local flow usually approached the spike centerline from the upper outboard side because of spike cant and toe-in. Free-stream Mach number influenced the local flow angularity; as Mach number increased above 2.2, local angle of attack increased and local sideslip angle decreased. Local Mach number was generally 3 percent less than free-stream Mach number. Impact-pressure ratio and mass flow ratio increased as free-stream Mach number increased above 2.2, indicating a beneficial forebody compression effect. No degradation of the spike tip instrumentation was observed after more than 40 flights in the high-speed thermal environment encountered by the airplane. The sensor is rugged, simple, and sensitive to small flow changes. It can provide accurate imputs necessary to control an inlet.

Johnson, H. J.↗
NASA NTRS1975

Amplification, attenuation, and dispersion of sound in inhomogeneous flows

First order effects of gradients in nonuniform potential flows of a compressible gas are included in a dispersion relation for sound waves. Three nondimensional numbers, the ratio of the change in the kinetic energy in one wavelength to the thermal energy of the gas, the ratio of the change in the total energy in one wavelength to the thermal energy, and the ratio of the dillatation frequency (the rate of expansion per unit volume) to the acoustic frequency, play a role in the separation of the effects of flow gradients into isotropic and anisotropic effects. Dispersion and attenuation (or amplification) of sound are found to be proportional to the wavelength for small wavelength, and depend on the direction of wave propagation relative to flow gradients. Modification of ray acoustics for the effects of flow gradients is suggested, and conditions for amplification and attenuation of sound are discussed.

Kentzer, C. P.↗
NASA NTRS1975

Amplification, attenuation, and dispersion of sound in inhomogeneous flows

First order effects of gradients in nonuniform potential flows of a compressible gas are included in a dispersion relation for sound waves. Three nondimensional numbers, the ratio of the change in the kinetic energy in one wavelength to the thermal energy of the gas, the ratio of the change in the total energy in one wavelength to the thermal energy, and the ratio of the dilatation frequency (the rate of expansion per unit volume) to the acoustic frequency, play the dominant role permitting the separation of the effects of flow gradients into isotropic and anisotropic effects. Dispersion and attenuation (or amplification) of sound are proportional to the wavelength for small wavelength and depend on the direction of wave propagation relative to flow gradients. Modification of ray acoustics for the effects of flow gradients is suggested and conditions for amplification and attenuation of sound are discussed.

Kentzer, C. P.↗
NASA NTRS1981

Stellar clustering as induced by a supernova

A possible mechanism for the fragmentation of the expanding shock wave from a supernova to form stellar clusters is considered. A model of supernova shell expansion is constructed in which the ratio of magnetic field intensity to gas density remains constant during the one-dimensional compression of the interstellar medium by the shock, and the gas and field adjust to a quasi-equilibrium within the shell following shock passage. It is shown that the quasi-equilibrium, which may be considered as an isothermal atmosphere, is unstable to a hydromagnetic instability representing a form of the Parker instability, which results in a clumping of gas at intervals on the order of parsecs. The length and time scales of the instability are consistent with the clustering of newly formed stars observed in Canis Major R1, where there is evidence for supernova-induced star formation.

Baierlein, R.↗
NASA NTRS1984

The 20 x 20 high speed microwave switches

Tests were conducted at NASA Lewis Research Center to characterize the proof-of-concept matrix switches built under NASA contract by Ford Aerospace and Aeronautics Corporation at Palo Alto, California, and the General Electric Company at Valley Forge, Pennsylvania. The contract requirements and goals are tabulated along with the results of the NASA tests. Characteristics examined are bandwidth, insertion loss, ripple, switching speed, isolation, standing wave ratio (input and output), deviation from linear phase, noise figure, reconfiguration rates, spurious responses, gain compression, and third order intermodulation distortion. A brief description of the testing method and a statistical analysis of the test results for each of the switches are provided.

Saunders, A.↗
NASA NTRS1984

Complete flowfields over low and wide angle AOTV conceptual configurations

Flowfields over two conceptual aeroassisted orbital transfer vehicles, a moderate lift-to-drag ratio biconic, and an axisymmetric zero lift aerobrake are investigated. The solution procedures employ a compressible Navier-Stokes time-asymptotic technique for blunt body flow and a Parabolized Navier-Stokes spatial marching technique for the primarily supersonic shock layer flow over low-angle bodies. Emphasis is placed on the laminar convective heating predictions and comparisons to experimental data where available. Code robustness and solution times are discussed and guidelines are given for the specification of various numerical parameters. The Parabolized Navier-Stokes technique has a high probability of solution success for the range of applications considered herein, and very good comparisons with experimental heat-transfer data have been obtained. The blunt body Navier-Stokes code is more sensitive to parameter specification for the aerobrake calculations. Still, coarse grid solutions can be obtained quickly to get a good first cut at flowfield definition. Fair to good comparisons have been obtained between experimental heating and pressure data and coarse and fine grid solutions.

Gnoffo, P. A.↗
NASA NTRS1985

Intraplate deformation due to continental collisions: A numerical study of deformation in a thin viscous sheet

A model of crustal deformation from continental collision that involves the penetration of a rigid punch into a deformable sheet is investigated. A linear viscous flow law is used to compute the magnitude and rate of change of crustal thickness, the velocity of mass points, strain rates and their principal axes, modes of deformation, areal changes, and stress. In general, a free lateral boundary reduces the magnitude of changes in crustal thickening by allowing material to more readily escape the advancing punch. The shearing that occurs diagonally in front of the punch terminates in compression or extension depending on whether the lateral boundary is fixed or free. When the ratio of the diameter of the punch to that of the sheet exceeds one-third, the deformation is insenstive to the choice of lateral boundary conditions. When the punch is rigid with sharply defined edges, deformation is concentrated near the punch corners. With non-rigid punches, shearing results in deformation being concentrated near the center of the punch. Variations with respect to linearity and nonlinearity of flow are discussed.

Cohen, S. C.↗
NASA NTRS1926

An Investigation of the Coefficient of Discharge of Liquids Through Small Round Orifices

The work covered by this report was undertaken in connection with a general investigation of fuel injection engine principles as applied to engines for aircraft propulsion, the specific purpose being to obtain information on the coefficient of discharge of small round orifices suitable for use as fuel injection nozzles. Values for the coefficient were determined for the more important conditions of engine service such as discharge under pressures up to 8,000 pounds per square inch, at temperatures between 80 degrees and 180 degrees F. And into air compressed to pressures up to 1,000 pounds per square inch. The results show that the coefficient ranges between 0.62 and 0.88 for the different test conditions between 1,000 and 8,000 pounds per square inch hydraulic pressure. At lower pressures the coefficient increases materially. It is concluded that within the range of these tests and for hydraulic pressures above 1,000 pound per square inch the coefficient does not change materially with pressure or temperature; that it depends considerably upon the liquid, decreases with increase in orifice size, and increases in the case of discharge into compressed air until the compressed-air pressure equals approximately three-tenths of the hydraulic pressure, beyond which pressure ratio it remains practically constant.

Joachim, W F↗
NASA NTRS1960

Free-Spinning-Tunnel Investigation of a 1/20-Scale Model of an Unswept-Wing Jet-Propelled Trainer Airplane

A flutter analysis employing the kernel function for three- dimensional, subsonic, compressible flow is applied to a flutter-tested tail surface which has an aspect ratio of 3.5, a taper ratio of 0.15, and a leading-edge sweep of 30 deg. Theoretical and experimental results are compared at Mach numbers from 0.75 to 0.98. Good agreement between theoretical and experimental flutter dynamic pressures and frequencies is achieved at Mach numbers to 0.92. At Mach numbers from 0.92 to 0.98, however, a second solution to the flutter determinant results in a spurious theoretical flutter boundary which is at a much lower dynamic pressure and at a much higher frequency than the experimental boundary.

Bowman, James S., Jr.↗
NASA NTRS1960

Subsonic Kernel-Function Flutter Analysis of a Highly Tapered Tail Surface and Comparison with Experimental Results

A flutter analysis employing the kernel function for three-dimensional, subsonic, compressible flow is applied to a flutter-tested tail surface which has an aspect ratio of 3.5, a taper ratio of 0.15, and a leading-edge sweep of 30 deg. Theoretical and experimental results are compared at Mach numbers from 0.75 to 0.98. Good agreement between theoretical and experimental flutter dynamic pressures and frequencies is achieved at Mach numbers to 0.92. At Mach numbers from 0.92 to 0.98, however, a second solution to the flutter determinant results in a spurious theoretical flutter boundary which is at a much lower dynamic pressure and at a much higher frequency than the experimental boundary.

Walberg, Gerald D.↗
NASA NTRS2004

The Performance of a Subsonic Diffuser Designed for High Speed Turbojet-Propelled Flight

An initial-phase subsonic diffuser has been designed for the turbojet flowpath of the hypersonic x43B flight demonstrator vehicle. The diffuser fit into a proposed mixed-compression supersonic inlet system and featured a cross-sectional shape transitioning flowpath (high aspect ratio rectangular throat-to-circular engine face) and a centerline offset. This subsonic diffuser has been fabricated and tested at the W1B internal flow facility at NASA Glenn Research Center. At an operating throat Mach number of 0.79, baseline Pitot pressure recovery was found to be just under 0.9, and DH distortion intensity was about 0.4 percent. The diffuser internal flow stagnated, but did not separate on the offset surface of this initial-phase subsonic diffuser. Small improvements in recovery (+0.4 percent) and DH distortion (-32 percent) were obtained from using vane vortex generator flow control applied just downstream of the diffuser throat. The optimum vortex generator array patterns produced inflow boundary layer divergence (local downwash) on the offset surface centerline of the diffuser, and an inflow boundary layer convergence (local upwash) on the centerline of the opposite surface.

Biesiadny, Thomas J.↗
NASA NTRS1996

The stability of compressible mixing layers in binary gases

We present the results of a study of the inviscid two-dimensional spatial stability of a parallel compressible mixing layer in a binary gas. The parameters of this study are the Mach number of the fast stream, the ratio of the velocity of the slow stream to that of the fast stream, the ratio of the temperatures, the composition of the gas in the slow stream and in the fast stream, and the frequency of the disturbance wave. The ratio of the molecular weight of the slow stream to that of the fast stream is found to be an important quantity and is used as an independent variable in presenting the stability characteristics of the flow. It is shown that differing molecular weights have a significant effect on the neutral-mode phase speeds, the phase speeds of the unstable modes, the maximum growth rates and the unstable frequency range of the disturbances. The molecular weight ratio is a reasonable predictor of the stability trends. We have further demonstrated that the normalized growth rate as a function of the convective Mach number is relatively insensitive (Approx. 25%) to changes in the composition of the mixing layer. Thus, the normalized growth rate is a key element when considering the stability of compressible mixing layers, since once the basic stability characteristics for a particular combination of gases is known at zero Mach number, the decrease in growth rates due to compressibility effects at the larger convective Mach numbers is somewhat predictable.

Kozusko, F.↗
NASA NTRS1981

Flow separation in shear-layer-driven cavities

A study of the shear-layer flow over a range of open-top cavity configurations is reported. Emphasis is placed on the effect that altering the cavity's span length and aspect ratio has on the development of the shear layer. Computational results are obtained using an interactive method which adapts the compressible boundary-layer model for the flow above the cavity and incompressible Navier-Stokes equations within the enclosure. Interaction of this composite model with the outer, inviscid supersonic flow is also considered in one case. The results show that the location of the stagnation points is sensitive primarily to the variation of the span. When the span was fixed and the aspect ratio varied, the shear layer was nearly unaffected except at aspect ratios less than 0.5. Interaction with the outer flow had a smoothing effect on the shape of the dividing streamline but did not significantly affect the location of the stagnation points.

Brandeis, J.↗
NASA NTRS1993

Active stabilization to prevent surge in centrifugal compression systems

This report documents an experimental and analytical study of the active stabilization of surge in a centrifugal engine. The aims of the research were to extend the operating range of a compressor as far as possible and to establish the theoretical framework for the active stabilization of surge from both an aerodynamic stability and a control theoretic perspective. In particular, much attention was paid to understanding the physical limitations of active stabilization and how they are influenced by control system design parameters. Previously developed linear models of actively stabilized compressors were extended to include such nonlinear phenomena as bounded actuation, bandwidth limits, and robustness criteria. This model was then used to systematically quantify the influence of sensor-actuator selection on system performance. Five different actuation schemes were considered along with four different sensors. Sensor-actuator choice was shown to have a profound effect on the performance of the stabilized compressor. The optimum choice was not unique, but rather shown to be a strong function of some of the non-dimensional parameters which characterize the compression system dynamics. Specifically, the utility of the concepts were shown to depend on the system compliance to inertia ratio ('B' parameter) and the local slope of the compressor speedline. In general, the most effective arrangements are ones in which the actuator is most closely coupled to the compressor, such as a close-coupled bleed valve inlet jet, rather than elsewhere in the flow train, such as a fuel flow modulator. The analytical model was used to explore the influence of control system bandwidth on control effectiveness. The relevant reference frequency was shown to be the compression system's Helmholtz frequency rather than the surge frequency. The analysis shows that control bandwidths of three to ten times the Helmholtz frequency are required for larger increases in the compressor flow range. This has important implications for implementation in gas turbine engines since the Helmholtz frequencies can be over 100 Hz, making actuator design extremely challenging.

Epstein, Alan H.↗
NASA NTRS1986

Boundary layer transition

The boundary layer stability, its active control by sound and surface heating and the effect of curvature are studied numerically and experimentally for subsonic flow. In addition, the experimental and flight test data are correlated using the stability theory for supersonic Mach numbers. Active transition fixing and feedback control of boundary layer by sound interactions are experimentally investigated at low speed over an airfoil. Numerical simulation of active control by surface heating and cooling in air shows that by appropriate phase adjustment a reduction in the level of perturbation can be obtained. This simulation is based on the solution of two-dimensional compressible Navier-Stokes equations for a flat plate. Goertler vortices are studied experimentally on an airfoil in the Low Turbulence Pressure Tunnel (LTPT). The flow pattern was visualized using the sublimating chemical technique and data were obtained using a three component laser velocimeter. The effect of curvature on swept leading-edge stability on a cylinder was numerically studied. The results suggest that transition is dominated by traveling disturbance waves and that the waves with the greatest total amplification has an amplitude ratio of e sup 11. Experimental data from the quiet supersonic tunnel and flight tests are analyzed using linear compressible stability theory.

Maestrello, L.↗
NASA NTRS1962

SOME RESULTS ON BUCKLING AND POSTBUCKLING OF CYLINDRICAL SHELLS

In this summary paper, the effects of initial deformations on the buckling and postbuckling characteristics of circular cylindrical shells under hydrostatic pressure is determined in an approximate manner. The influence of initial axisymmetric deformations is stressed. Also, the classical buckling of an axially compressed, noncircular (oval) cylindrical shell is studied. The results show that the major-minor axis ratio of the cross section has a marked effect on the critical load, and that use of the maximum radius of curvature in the formula for the classical buckling stress of a circular cylindrical shell leads to good results for moderate eccentricities.

BUCKLING↗