Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cu surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Cu Doping Increases Capacity Retention in LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) by Altering the Potential of the Ni-Based Redox Couple and Inhibiting Particle Pulverization

To discern the influence of Cu 2+ as a dopant on both the structural and electrochemical characteristics of LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622), Cu 2+ (aq) was added to the coprecipitation synthesis from the constituent ions. At 5 mol % Cu 2+ , a single-phase Cu-NMC product results, evidenced by an increase in d-spacing along the [003] and [104] directions and a slight increase in the crystal volume of the R–3m hexagonal (rock-salt superstructure) lattice. XRD data and high-resolution TEM imaging support Cu 2+ doping primarily on the transition metal 3b Wyckoff sites. Here, galvanostatic cycling of Cu-NMC shows a reversible gravimetric capacity of 102 mAh/g compared to 136 mAh/g for undoped NMC. Despite the lower capacity, the discharge capacity retention of Cu-NMC is 89% after 100 cycles compared to only 70% for NMC. XPS analysis reveals that this lower capacity is due to an increase in the concentration of Ni 3+ ions at the surface, while XRD data collected at the top and bottom of charge show a smaller decrease in crystalline domain size for Cu-NMC (40.5% decrease) compared to NMC (74.7% decrease), translating to pulverization of the secondary particles.

25 ENERGY STORAGE↗
DOE OSTI2022

Elucidating size effects on the yield strength of single-crystal Cu via the Richtmyer–Meshkov instability

Capturing the dynamic response of a material under high strain-rate deformation often demands challenging and time consuming experimental effort. While shock hydrodynamic simulation methods can aid in this area, a priori characterizations of the material strength under shock loading and spall failure are needed in order to parameterize constitutive models needed for these computational tools. Moreover, parameterizations of strain-rate-dependent strength models are needed to capture the full suite of Richtmyer–Meshkov instability (RMI) behavior of shock compressed metals, creating an unrealistic demand for these training data solely on experiments. Herein, we sweep a large range of geometric, crystallographic, and shock conditions within molecular dynamics (MD) simulations and demonstrate the breadth of RMI in Cu that can be captured from the atomic scale. In this work, yield strength measurements from jetted and arrested material from a sinusoidal surface perturbation were quantified as Y RMI = 0.787 ± 0.374 GPa, higher than strain-rate-independent models used in experimentally matched hydrodynamic simulations. Defect-free, single-crystal Cu samples used in MD will overestimate Y RMI , but the drastic scale difference between experiment and MD is highlighted by high confidence neighborhood clustering predictions of RMI characterizations, yielding incorrect classifications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Stability of Pt Skin Intermetallic Core Catalysts and Adsorption Properties for the Oxygen Reduction Reaction

Density functional theory calculations were used to determine the stability of metal slabs consisting of a Pt surface monolayer and intermetallic supporting layers made from combinations of six transition metal elements (Pt, Fe, Co, Ni, Cu, and Ag), as a model system for Pt skin intermetallic core nanoparticle catalysts. The stability of the slabs is largely determined by strain at the interface of the Pt skin and the subsurface intermetallic, which was described by a lattice matching parameter (r). The surface charge on the Pt skin was found to be correlated with the average electronegativity (EN) of the intermetallic core, so this average EN was used as a descriptor for how the electronic coupling (or ligand effect) affects adsorption energies. A total of 46 slabs were investigated in terms of their stability, from which 10 stable slabs were selected for further studies of adsorbate binding (OOH*, O*, and OH*) that are intermediates in the oxygen reduction reaction (ORR). The correlation between all three adsorption energies and descriptors r and EN was found. Using a linear fit between our descriptors and the calculated adsorption energies, the overpotential for the ORR was obtained as a function of r and EN, from which a volcano plot was produced. The volcano peak was found at r = 0.96 or at EN = 2.025. Interestingly, neither r nor EN was a sufficient single reactivity descriptor as the data points were well off the general trend in both linear fits; this implies that both the strain effect and the ligand effect influence the adsorption energies, although they are partly correlated. The (r, EN) target peak parameters were used to screen over 241 intermetallic combinations of transition metal elements as active ORR activity. In conclusion, this analysis identified 11 intermetallic compounds which can support a Pt skin to have a high predicted ORR activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Tuning the Product Distribution of Acetylene Dimerization through Bimetallic Metal–Organic Framework-Supported Nanoporous Systems

Metal-organic frameworks (MOFs) are receiving increased attention due to their well-defined structures that allow the determination of structure-property relationships. MOFs have been used as heterogeneous catalyst supports in a variety of fashions including for confinement of metal nanoparticles, which have demonstrated enhanced resistance to aggregation, a common issue in amorphous metal oxide supports. Cu and In catalysts were installed in the Zr-based MOF NU-907, being confined within the nanoporous structure. The Cu catalyst is known to, under various conditions, either selectively hydrogenate acetylene to ethylene or generate C4 products such as butenes and 1,3-butadiene, an important feedstock for rubber and adhesives. The addition of indium to the Cu catalyst is intended to serve as a promoter to produce C4 products by decreasing the surface coverage of copper while still allowing for C-C coupling. When employed for acetylene dimerization, InCu-NU-907 shows slightly decreased C4 production overall but enhanced 1,3-butadiene production compared to all other catalysts studied herein. These catalysts were thoroughly characterized by a range of techniques to confirm structural integrity and porosity and probe the nature of the interactions of indium with the Cu nanoparticle active site.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Boosting Hydrogenation of CO 2 Using Cationic Cu Atomically Dispersed on 2D γ‐Al 2 O 3 Nanosheets

The continuous development of novel catalytic approaches is crucial for advancing efficient CO 2 hydrogenation processes. Drawing inspiration from single-atom catalysis and 2D materials, we designed a new 2D single-atom catalyst with excellent thermal stability by thermally treating Cu-adsorbed γ-AlOOH nanosheets, which yielded a Cu/γ-Al 2 O 3 catalyst with high activity in the hydrogenation of CO 2 -yielding methanol (CH 3 OH), dimethyl ether (DME), and CO as products. The active Cu sites are monodispersed and highly stable due to their cationic oxidation state and their substitution for pentacoordinated aluminum (Al P ) sites on particle surfaces. This study demonstrates an efficient approach for achieving a high CO 2 hydrogenation rate (30.45 mol mol −1 h −1 ) using a catalyst system that lacks metallic Cu centers, traditionally considered essential for H₂ dissociation, and employs what was previously thought to be an inert metal oxide (γ-Al 2 O 3 ) for CO and CH 3 OH production. Ongoing mechanistic studies aim to elucidate the synergy between cationic Cu single atoms and γ-Al 2 O 3 , a Lewis acid support, in facilitating hydrogen (H 2 ) activation and methanol formation.

2D catalyst↗
DOE OSTI2023

Robust Copper-Based Nanosponge Architecture Decorated by Ruthenium with Enhanced Electrocatalytic Performance for Ambient Nitrogen Reduction to Ammonia

Electrochemical conversion of nitrogen to green ammonia is an attractive alternative to the Haber–Bosch process. However, it is currently bottlenecked by the lack of highly efficient electrocatalysts to drive the sluggish nitrogen reduction reaction (N2RR). In this work, we strategically design a cost-effective bimetallic Ru–Cu mixture catalyst in a nanosponge (NS) architecture via a rapid and facile method. The porous NS mixture catalysts exhibit a large electrochemical active surface area and enhanced specific activity arising from the charge redistribution for improved activation and adsorption of the activated nitrogen species. Benefiting from the synergistic effect of the Cu constituent on morphology decoration and thermodynamic suppression of the competing hydrogen evolution reaction, the optimized Ru 0.15 Cu 0.85 NS catalyst presents an impressive N 2 RR performance with an ammonia yield rate of 26.25 μg h –1 mg cat. –1 (corresponding to 10.5 μg h –1 cm –2 ) and Faradic efficiency of 4.39% as well as superior stability in alkaline medium, which was superior to that of monometallic Ru and Cu nanostructures. Additionally, this work develops a new bimetallic combination of Ru and Cu, which promotes the strategy to design efficient electrocatalysts for electrochemical ammonia production under ambient conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

3D and Multimodal X‐Ray Microscopy Reveals the Impact of Voids in CIGS Solar Cells

Small voids in the absorber layer of thin-film solar cells are generally suspected to impair photovoltaic performance. They have been studied on Cu(In,Ga)Se 2 cells with conventional laboratory techniques, albeit limited to surface characterization and often affected by sample-preparation artifacts. Here, synchrotron imaging is performed on a fully operational as-deposited solar cell containing a few tens of voids. By measuring operando current and X-ray excited optical luminescence, the local electrical and optical performance in the proximity of the voids are estimated, and via ptychographic tomography, the depth in the absorber of the voids is quantified. Besides, the complex network of material-deficit structures between the absorber and the top electrode is highlighted. Despite certain local impairments, the massive presence of voids in the absorber suggests they only have a limited detrimental impact on performance.

14 SOLAR ENERGY↗
DOE OSTI2024

When Photoelectrons Meet Gas Molecules: Determining the Role of Inelastic Scattering in Ambient Pressure X-ray Photoelectron Spectroscopy

Inelastic photoelectron scattering (IPES) by gas molecules, a critical phenomenon observed in ambient pressure X-ray photoelectron spectroscopy (APXPS), complicates spectral interpretation due to kinetic energy loss in the primary spectrum and the appearance of additional features at higher binding energies. In this study, we systematically investigate IPES in various gas environments using APXPS, providing detailed insights into interactions between photoelectrons emitted from solid surfaces and surrounding gas molecules. Corelevel XPS spectra of Au, Ag, Zn, and Cu metals were recorded over a wide kinetic energy range in the presence of CO 2 , N 2 , Ar, and H 2 gases, demonstrating the universal nature of IPES across different systems. Additionally, we analyzed spectra of scattering effects induced by gas-phase interactions without metal solids. In two reported CO 2 -reduction systems (p-GaN/ Au/Cu and p-Si/TaO x /Cu), we elucidated that IPES is independent of the composition, structure, or size of the solid materials. Using metal foil platforms, we further developed an analytical model to extract electron excitation cross sections of gas molecules. These findings enhance our understanding of IPES mechanisms and enable the predictions of IPES structures in other solid–gas systems, providing a valuable reference for future APXPS studies and improving the accuracy of spectral analysis in gas-rich catalytic interfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Colorimetric Detection and Surface Decontamination of Metal Ions by Using Strippable Polymers - 20024

Strippable coating is a low cost and efficient decontamination method far more compatible for the cleaning of surfaces. This method allows contaminant entrapment and removal from different types of surfaces and also characterized by low-secondary waste generation after decontamination. The present work deals with the elaboration and testing of a new composition of Polyvinyl alcohol (PVA) aqueous solutions utilize the TTA (Thenoyl trifluoroacetone) ligand, employed as a strippable coating for the removal of metal ions e.g., UO{sub 2}{sup +2}, Ni{sup +2}, Cu{sup +2}, Fe{sup +3}, V{sup +5}, Eu{sup +3} and Cs{sup +} from 'contaminated' surfaces. The study aims at developing contaminant-sensing and decontaminating coatings for the detection and removal of metal ions from non porous surfaces. This 'smart' coating is shown to exhibit a clear contaminant dependent response in the form of color variation, and a detection sensitivity less than 0.5 μg per cm{sup 2}. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Effect of nitriding on mechanical and microstructural properties of Direct Metal Laser Sintered 17-4PH stainless steel

In this work, the effect of the nitriding process on microstructure and mechanical properties of additively manufactured (AM) 17-4PH stainless steel is investigated. The nitriding was performed at 530 °C, 560 °C, and 580 °C for 2 h. The nitriding process improves the hardness and surface roughness of the AM 17-4PH steel. Detailed microstructural characterizations of both as-built and nitride samples are performed using an optical microscope, scanning electron microscope (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction technique. It reveals that the nitride layer thickness increases with nitriding temperature. A distinct transition layer between the substrate and nitride layer is observed in the 560 °C and 580 °C nitride samples. The nitriding process develops almost equiaxed grain microstructure with new secondary phase precipitates, whereas in the as-built material, the grains are primarily columnar along the AM process build direction. Specifically, the nitriding process introduces γ-Fe4N, ε-Fe3N, CrN, and Ni3N precipitates. The increase in Ni- and Cu-rich precipitates with the nitriding temperature explains the observed improvement in the hardness and surface roughness. Furthermore, the nitriding process does not alter the substrate's initial weak crystallographic texture.

17-4PH steel↗
DOE OSTI2021

Near surface defects: Cause of deficit between internal and external open-circuit voltage in solar cells

The presence of interface recombination in a complex multilayered thin-film solar structure causes a disparity between the internal open-circuit voltage (V OC,in ), measured by photoluminescence, and the external open-circuit voltage (V OC,ex ) i.e. an additional V OC deficit. Higher V OC,ex value aim require a comprehensive understanding of connection between V OC deficit and interface recombination. Here, a deep near-surface defect model at the absorber/buffer interface is developed for copper indium di-selenide solar cells grown under Cu excess conditions to explain the disparity between V OC ,in and V OC,ex . The model is based on experimental analysis of admittance spectroscopy and deep-level transient spectroscopy, which show the signature of deep acceptor defect. Further, temperature-dependent current-voltage measurements confirm the presence of near surface defects as the cause of interface recombination. The numerical simulations show strong decrease in the local V OC ,in near the absorber/buffer interface leading to a V OC deficit in the device. This loss mechanism leads to interface recombination without a reduced interface bandgap or Fermi level pinning. Further, these findings demonstrate that the V OC ,in measurements alone can be inconclusive and might conceal the information on interface recombination pathways, establishing the need for complementary techniques like temperature dependent current voltage measurements to identify the cause of interface recombination in the devices.

14 SOLAR ENERGY↗
DOE OSTI2022

Uptake and speciation of trace metal inputs to Wetland Soils from Illinois and South Carolina and Stream Sediments from Tennessee

Metals occur in all ecosystems, although their concentrations vary depending on their natural geologic conditions and surrounding human activities. In addition to metals intrinsically present from the geology of a particular system, metals can enter environmental systems from a wide variety of natural and anthropogenic sources, such as sediment re-suspension, mining operations, industrial processes, agricultural activities, and atmospheric deposition. While metals can be toxic at high concentrations, some metals serve as essential micronutrients for biogeochemical processes. Metal transport and availability in engineered and natural water systems depend on processes of adsorption/desorption, oxidation/reduction, dissolution/precipitation, and ligand complexation. Insights into the speciation of metals and their bioavailability will also help advance understanding of the roles of metals in the biogeochemical cycling of nutrients. We conducted batch experiments under anoxic conditions on soils and sediments collected from three different natural aquatic systems to understand their response to influxes of dissolved Cu, Ni and Zn. While soils and sediments from all sites could strongly bind added trace metals, there were substantial differences in trace metal uptake trends between different sites, especially for Cu. There was no distinct correlation between trace metal uptake and the total organic matter, iron, and sulfur content present in the samples. X-ray absorption spectroscopy indicated that the speciation of the freshly added metals taken up by the solids differs substantially from the speciation of the metals originally present in unamended samples. Cu sulfides dominated speciation at low loadings (1 µmol/g), whereas complexation to thiol groups and formation of metallic Cu governed speciation at high loadings (10 µmol/g). For Ni and Zn, adsorption to mineral surfaces and organic matter governed their speciation in materials from most sites. This study suggests that the background speciation of metals in natural aquatic systems is a poor predictor of the speciation and lability of metals introduced to terrestrial aquatic systems from anthropogenic or natural processes. Our findings imply that geochemical processes controlling trace metal speciation may vary considerably with metal loading in different natural systems. Data are provided for marsh wetland soils at Argonne National Laboratory (Marsh 1 and Marsh 2), riparian wetland soils (Riparian 1 and Riparian 2) in the Tims Branch watershed at Savannah River National Laboratory, and stream bed sediments (Stream 1 and Stream 2) from East Fork Poplar Creek near Oak Ridge National Laboratory. Data package includes the results of trace metal uptake experiments conducted on the selected sites for determining their capacity to immobilize metals under different loadings. XANES spectra for Cu, Ni, ad Zn at different loadings are included in the package. The abundance of different trace metal species obtained using linear combination fitting in ATHENA are also included in the data.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Insights into palladium poisoning of Cu/SSZ-13 selective catalytic reduction catalysts

Here, the impacts of Pd poisoning to the activity, selectivity, and hydrothermal stability of Cu/SSZ-13 selective catalytic reduction (SCR) catalysts are reported. Pd lowers DeNOx efficiency of Cu/SSZ-13 via two mechanisms: (1) displacing SCR active sites in the form of isolated Pd-ions, and (2) catalyzing non-selective NH 3 oxidation in the form of PdO. The first mechanism works by the diffusion of isolated Pd-ions into chabazite cages to displace ZCu II OH SCR active species, and it occurs on Cu/SSZ-13 catalysts with and without external surface CuO clusters in similar fashion. In contrast, the second mechanism works differently with and without external surface CuO clusters. For Cu/SSZ-13 catalyst without external CuO clusters (i.e., primarily isolated Cu-ions), PdO leads to significant decrease of DeNOx efficiency at reaction temperatures above ~400°C due to its non-selective NH 3 oxidation activity at high temperatures. However, this poisoning effect becomes much less impactful on Cu/SSZ-13 catalyst containing CuO clusters. This is due to the formation of CuO-PdO solid solution via interactions between CuO and PdO, which reduces non-selective NH 3 oxidation potential. Furthermore, this solid solution formation even mitigates adverse effects caused by hydrothermal aging. Hence, the poisoning effects of Pd are closely related to Cu speciation and spatial distribution of a Cu/SSZ-13 catalyst. Finally, this study suggests a strategy in eliminating Pd poisoning, that is, the introduction of an oxide phase that effectively traps PdO but does not adversely influence SCR.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Electrolyte-Guided Design of Electroreductive CO Coupling on Copper Surfaces

Engineering the interfacial distribution of electrolytic ions can aid in modulating the electrocatalyst performance and efficiency. Using a hybrid quantum-classical modeling approach, we describe how predictive tuning of the solution microenvironment on copper can enhance the efficiency of CO 2 reduction (CO 2 R) to C 2 products. We elucidate how competing electrolyte constituents in mixed electrolyte solutions stimulate restructuring of the electrochemical double layer (EDL) and stabilize the OCCO* dimer (* denotes surface adsorbed), with predictions validated in flow reactors using copper gas diffusion electrodes (Cu-GDEs). Furthermore, our findings highlight how molecular-scale electrolyte engineering with informed models of the EDL can be leveraged to tailor CO 2 R activity and selectivity toward C 2 products.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Application-driven synthesis and characterization of hexagonal boron nitride deposited on metals and carbon nanotubes

Hexagonal boron nitride (h-BN) is unique among two-dimensional materials, with a large band gap (~6 eV) and high in-plane thermal conductivity (>400 W m -1 K -1 ), second only to diamond among electrical insulators. Many studies to date have relied on exfoliated h-BN, however, for large-scale applications the material must be synthesized by methods such as chemical vapor deposition (CVD). Here, we first investigate single-layer h-BN synthesized by CVD on single crystal platinum (Pt), comparing these films with h-BN deposited on more commonly used polycrystalline Pt and Cu. The h-BN film grown on single crystal Pt has the lowest surface roughness and best spatial homogeneity, and our electrochemical transfer process allows the Pt to be reused with no measurable degradation. Additionally, we also demonstrate direct capping of carbon nanotubes (CNTs) with as-grown h-BN, but we find that the direct growth partly degrades the CNT electrical conductivity. On the other hand, we show that transferred monolayer h-BN can serve as an ultrathin barrier which protects MoS2 from damage at high temperatures and discuss other applications that take advantage of the conformal h-BN deposition.

2D materials↗
DOE OSTI2023

Analysis of position-dependent cavity parameters in irradiated metals to obtain insight on fundamental defect migration phenomena

Motion of point defects is a fundamental process that governs microstructure and properties of materials. Here, we examine the near-surface and grain boundary cavity swelling depth profiles in neutron- and ion-irradiated simple metals (Cu, Ni, and Fe-Cr) and investigate diffusional broadening of implanted Ni ions in Fe-Cr alloys. Vacancy migration energies and radiation-enhanced diffusion were experimentally estimated. Cavity denuded zone widths near planar sinks are shown to be dependent on temperature, damage rate, balance of point defects and sinks, and vacancy migration energies. An enhanced cavity swelling zone adjacent to the void-denuded zone was observed in specimens with low to moderate sink strength and interpreted as evidence of 1D gliding interstitial clusters. Radiation-enhanced diffusional broadening of implanted Ni ions (at 400–550 °C) in Fe and Fe-Cr was up to 250 nm toward the surface, which leads to a much broader near-peak-damage region where cavity swelling is suppressed. Diffusional broadening of implanted ions is calculated to be similarly pronounced for self-ion irradiations, particularly near the peak and higher swelling temperature regimes. Adequately high ion energies (~8–15 MeV) are recommended for ion-irradiation studies to provide a sufficiently broad midrange safe analysis region with minimized surface and injected ion effects.

36 MATERIALS SCIENCE↗
DOE OSTI2025

On-line Inductively Coupled Plasma Mass Spectrometry Reveals Material Degradation Dynamics of Au and Cu Catalysts during Electrochemical CO 2 Reduction

A significant challenge in commercializing electrochemical CO 2 reduction (CO 2 R) is achieving catalyst durability. Here, in this study, online inductively coupled mass spectrometry (ICP–MS) was used to investigate catalyst degradation via nanoparticle detachment and/or dissolution into metal ions under CO 2 R operating conditions in 0.1 M KHCO 3 . We developed an experimental framework with ex situ characterization to validate the online ICP–MS method for in situ evaluation of degradation from metal foils. By varying the applied potential and microenvironment (CO 2 vs N 2 -saturated electrolyte), we gained insights into the degradation of Au and Cu foils under CO 2 R and hydrogen evolution reaction (HER) conditions. While both Au and Cu foils were observed to be stable to dissolution in these regimes, degradation via nanoparticle detachment from the foil surface at the femtogram scale was observed as a function of reaction conditions, providing new insights into material degradation mechanisms. When applying potential steps at −0.1 and −1.0 V vs the reversible hydrogen electrode (RHE), Au was found to degrade via nanoparticle detachment under CO 2 R operating conditions more than under HER conditions, while Cu was found to degrade via nanoparticle detachment in similar amounts during both reactions. Au lost ∼1.8× more mass and ∼7.5× more nanoparticles than Cu under CO 2 R operating conditions. This study demonstrates the use of online ICP–MS to gain insight into the degradation of Au and Cu, the importance of studying unconventional degradation mechanisms such as nanoparticle detachment, and that online ICP–MS can be further utilized to gain fundamental understanding of catalyst durability for a variety of reaction systems.

Yan, Katherine [Stanford Univ., CA (United States)↗