SEARCH · Search NASA

Results for “Distillates”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Recent trends in aviation turbine fuel properties

Plots and tables, compiled from Department of Energy (and predecessor agency) inspection reports from 1969 to 1980, present ranges, averages, extremes, and trends for most of the 22 properties of Jet A aviation turbine fuel. In recent years, average values of aromatics content, mercaptan sulfur content, distillation temperature of 10 percent recovered, smoke point, and freezing point show small but recognizable trends toward their specification limits. About 80 percent of the fuel samples had at least one property near specification, defined as within a standard band about the specification limit. By far the most common near-specification properties were aromatics content, smoke point, and freezing point.

Friedman, R.↗

NASA NTRS1982

Catalytic combustion with steam injection

The effects of steam injection on (1) catalytic combustion performance, and (2) the tendency of residual fuel to burn in the premixing duct upstream of the catalytic reactor were determined. A petroleum residual, no. 2 diesel, and a blend of middle and heavy distillate coal derived fuels were tested. Fuel and steam were injected together into the preheated airflow entering a 12 cm diameter catalytic combustion test section. The inlet air velocity and pressure were constant at 10 m/s and 600 kPa, respectively. Steam flow rates were varied from 24 percent to 52 percent of the air flow rate. The resulting steam air mixture temperatures varied from 630 to 740 K. Combustion temperatures were in the range of 1200 to 1400 K. The steam had little effect on combustion efficiency or emissions. It was concluded that the steam acts as a diluent which has no adverse effect on catalytic combustion performance for no. 2 diesel and coal derived liquid fuels. Tests with the residual fuel showed that upstream burning could be eliminated with steam injection rates greater than 30 percent of the air flow rate, but inlet mixture temperatures were too low to permit stable catalytic combustion of this fuel.

Anderson, D. N.↗

NASA NTRS1979

SKYMAP system description: Star catalog data base generation and utilization

The specifications, design, software description, and use of the SKYMAP star catalog system are detailed. The SKYMAP system was developed to provide an accurate and complete catalog of all stars with blue or visual magnitudes brighter than 9.0 for use by attitude determination programs. Because of the large number of stars which are brighter than 9.0 magnitude, efficient techniques of manipulating and accessing the data were required. These techniques of staged distillation of data from a Master Catalog to a Core Catalog, and direct access of overlapping zone catalogs, form the basis of the SKYMAP system. The collection and tranformation of data required to produce the Master Catalog data base is described. The data flow through the main programs and levels of star catalogs is detailed. The mathematical and logical techniques for each program and the format of all catalogs are documented.

Gottlieb, D. M.↗

NASA NTRS1982

Ultrapure glass optical waveguide development in microgravity by the sol-gel process

Containerless melting of glasses in space for the preparation of ultrapure homogeneous glass for optical waveguides is discussed. The homogenization of the glass using conventional raw materials is normally achieved on Earth either by the gravity induced convection currents or by the mechanical stirring of the melt. Because of the absence of gravity induced convection currents, the homogenization of glass using convectional raw materials is difficult in the space environment. Multicomponent, homogeneous, noncrystalline oxide gels can be prepared by the sol-gel process and these gels are promising starting materials for melting glasses in the space environment. The sol-gel process is based on the polymerization reaction of alkoxysilane with other metal alkoxy compounds or suitable metal salts. Many of the alkoxysilanes or other metal alkoxides are liquids and thus can be purified by distillation.

Source record↗

NASA NTRS1983

ECUT: Energy Conversion and Utilization Technologies program biocatalysis research activity. Potential membrane applications to biocatalyzed processes: Assessment of concentration polarization and membrane fouling

Separation and purification of the products of biocatalyzed fermentation processes, such as ethanol or butanol, consumes most of the process energy required. Since membrane systems require substantially less energy for separation than most alternatives (e.g., distillation) they have been suggested for separation or concentration of fermentation products. This report is a review of the effects of concentration polarization and membrane fouling for the principal membrane processes: microfiltration, ultrafiltration, reverse osmosis, and electrodialysis including a discussion of potential problems relevant to separation of fermentation products. It was concluded that advanced membrane systems may result in significantly decreased energy consumption. However, because of the need to separate large amounts of water from much smaller amounts of product that may be more volatile than wate, it is not clear that membrane separations will necessarily be more efficient than alternative processes.

Ingham, J. D.↗

NASA NTRS1983

Effect of hydration on nitrogen washout in human subjects

Five subjects were tested to assess the influence of drinking hypotonic water (distilled water) on whole body tissue nitrogen washout. During the test, the subjects breathed aviators' oxygen for three hours. Each subject performed two baseline nitrogen washouts in a two-week period. The third washout, in the third week, was done under a transient hydrated condition. This was accomplished by having the subjects drink 1.5 liters of hypotonic water 30 minutes before the washout. Five-minute plots of tissue nitrogen removal from the three separate washouts were analyzed to ascertain if the hydration technique had any effect. Our results clearly indicate that the hydration technique did not alter the tissue nitrogen washout characteristics to any degree over three hours. An increase in tissue nitrogen washout under a transient hydrated condition using hypotonic fluid was not demonstrated to be the mechanism responsible for the reported benefit of this technique in preventing Type I altitude decompression pain in man.

Waligora, J.↗

NASA NTRS1982

Thermoelectric integrated membrane evaporation water recovery technology

The recently developed Thermoelectric Integrated Membrane Evaporation Subsystem (TIMES) offers a highly competitive approach to water recovery from waste fluids for future on-orbit stations such as the Space Operations Center. Low power, compactness and gravity insensitive operation are featured in this vacuum distillation subsystem that combines a hollow fiber membrane evaporator with a thermoelectric heat pump. The hollow fiber elements provide positive liquid/gas phase control with no moving parts other than pumps and an accumulator, thus solving problems inherent in other reclamation subsystem designs. In an extensive test program, over 850 hours of operation were accumulated during which time high quality product water was recovered from both urine and wash water at an average steady state production rate of 2.2 pounds per hour.

Roebelen, G. J., Jr.↗

NASA NTRS1983

Water and acid soluble trace metals in atmospheric particles

Continental aerosols are collected above a deciduous forest in eastern Tennessee and subjected to selective extractions to determine the water-soluble and acid-leachable concentrations of Cd, Mn, Pb, and Zn. The combined contributions of these metals to the total aerosol mass is 0.5 percent, with approximately 70 percent of this attributable to Pb alone. A substantial fraction (approximately 50 percent or more) of the acid-leachable metals is soluble in distilled water. In general, this water-soluble fraction increases with decreasing particle size and with increasing frequency of atmospheric water vapor saturation during the sampling period. The pattern of relative solubilities (Zn being greater than Mn, which is approximately equal to Cd, which is greater than Pb) is found to be similar to the general order of the thermodynamic solubilities of the most probable salts of these elements in continental aerosols with mixed fossil fuel and soil sources.

Lindberg, S. E.↗

NASA NTRS1985

High-Temperature Coating for Titanium

Wet coating mixture composed of graphite pigment potassium silicate binder solution and distilled water. Resulting coating has electrical resistivity of less than 10 to the 6th power ohm-cm.

Mell, R. J.↗

NASA NTRS1983

Synthesis of N-Substituted Silaneamines: Monomeric Precursors of Silicon Carbide-Nitride Fibers

Silanetriamines are prepared by the condensation of methyl or phenyl trichlorosilane with a primary amine. The amines used were methyl, n-propyl, n-butyl and allyl. The silaneamines were prepared by adding the chlorosilane to a solution of the amine in either petroleum ether or toluene. The compounds were purified by distillation and characterized by infrared and nuclear magnetic resonance spectroscopy.

Crouse, D. J.↗

NASA NTRS1983

Effects of broadened property fuels on radiant heat flux to gas turbine combustor liners

The effects of fuel type, inlet air pressure, inlet air temperature, and fuel/air ratio on the combustor radiation were investigated. Combustor liner radiant heat flux measurements were made in the spectral region between 0.14 and 6.5 microns at three locations in a modified commercial aviation can combustor. Two fuels, Jet A and a heavier distillate research fuel called ERBS were used. The use of ERBS fuel as opposed to Jet A under similar operating conditions resulted in increased radiation to the combustor liner and hence increased backside liner temperature. This increased radiation resulted in liner temperature increases always less than 73 C. The increased radiation is shown by way of calculations to be the result of increased soot concentrations in the combustor. The increased liner temperatures indicated can substantially affect engine maintenance costs by reducing combustor liner life up to 1/3 because of the rapid decay in liner material properties when operated beyond their design conditions.

Haggard, J. B., Jr.↗

NASA NTRS1984

Trends of jet fuel demand and properties

Petroleum industry forecasts predict an increasing demand for jet fuels, a decrease in the gasoline-to-distillate (heavier fuel) demand ratio, and a greater influx of poorer quality petroleum in the next two to three decades. These projections are important for refinery product analyses. The forecasts have not been accurate, however, in predicting the recent, short term fluctuations in jet fuel and competing product demand. Changes in petroleum quality can be assessed, in part, by a review of jet fuel property inspections. Surveys covering the last 10 years show that average jet fuel freezing points, aromatic contents, and smoke points have trends toward their specification limits.

Friedman, R.↗

NASA NTRS1984

NASA broad-specification fuels combustion technology program

The NASA Broad-Specification Fuels Combustion Technology Program was initiated in response to concerns that the supply of high-quality petroleum middle distillates for jet fuel, abundant in the past, would diminish in availability toward the end of the century. The specific program objective is to evolve the combustion system technology required to use fuels with moderate ranges of broadened properties in the engines used on commercial jet aircraft. The first phase of the program, in which effects of the use of broadened-properties fuels were identified and technology with the potential to offset these effects was also identified, has been completed. The second phase, in which the technology identified in Phase 1 is being refined, will be completed within the next three months.

Fear, J. S.↗

NASA NTRS1983

Mineralogy and petrology of chondrules and inclusions in the Mokoia CV3 chondrite

The inclusions and chondrules of the Mokoia CV3 chondrite are studied systematically and compared with those in the Allende meteorite. Five polished thin sections of Mokoia were examined by optical microscopy, backscattered scanning electron microscopy, and electronprobe microanalysis, and objects greater than about 100 microns in apparent diameter were measured and classified petrographically. Three major types of olivine chondrules are distinguished: igneous chondrules, which evidently crystallized from droplets of silicate melt; recrystallized chondrules, apparently metamorphosed at relatively high temperatures; and accretional aggregates, which are probably fragments of igneous chondrules. Refractory inclusions in Mokoia are generally similar to those found in Allende, although Mokoia inclusions include phyllosilicates rather than feldspathoids and melilite-rich Ca, Al-rich inclusions (CAIs) are more abundant in Allende. The small, fine-grained CAIs, which are more abundant than coarse-grained CAIs in both meteorites, are observed to represent aggregates of three distinct constituents: concentric objects, chaotic material and inclusion matrix. It is concluded that most of the CAIs probably formed during metamorphism, partial melting, and incomplete distillation of primitive dust aggregates heated in the solar nebula.

Cohen, R. E.↗

NASA NTRS1984

Origin of spinel-rich chondrules and inclusions in carbonaceous and ordinary chondrites

The evaluation of three models of the origin of spinel-rich chondrules and inclusions presented here includes new calculations of the major-element refractory mineral condensation sequence from a gas of solar composition over a wide pressure interval. Condensation calculations show that spinel-rich chondrules did not crystallize from metastable liquid condensates, and that spinel-rich inclusions are not aggregates of refractory nebular condensates. It is proposed that spinel-rich objects are fractionated distillation residues of small aggregates of primitive dust that lost Ca, Si-rich partial melts by evaporation, ablation, or splashing during collisions. This model also explains why spinel-rich chondrules and inclusions (1) are usually smaller than melilite-rich chondrules and inclusions; (2) often have highly fractionated trace-element compositions; and (3) usually do not contain Pt-metal nuggets even when they are more enriched in the Pt-group metals than nugget-bearing melilite-rich objects.

Kornacki, A. S.↗

NASA NTRS1983

Integrated water management system - Description and test results

Water recovery subsystems are being tested at the NASA Lyndon B. Johnson Space Center for Space Station use to process waste water generated from urine and wash water collection facilities. These subsystems are being integrated into a water management system that will incorporate wash water and urine processing through the use of hyperfiltration and vapor compression distillation subsystems. Other hardware in the water management system includes a whole body shower, a clothes washing facility, a urine collection and pretreatment unit, a recovered water post-treatment system, and a water quality monitor. This paper describes the integrated test configuration, pertinent performance data, and feasibility and design compatibility conclusions of the integrated water management system.

Elden, N. C.↗

NASA NTRS1983

Urine pretreatment for waste water processing systems

Recovery of high quality water from urine is an essential part of life support on a Space Station to avoid costly launch and resupply penalties. Water can be effectively recovered from urine by distillation following pretreatment by a chemical agent to inhibit microorganism contamination and fix volatile ammonia constituents. This paper presents the results of laboratory investigations of several pretreatment chemicals which were tested at several concentration levels in combination with sulfuric acid in urine. The optimum pretreatment formulation was then evaluated with urine in the Hamilton Standard Thermoelectric Integrated Membrane Evaporation Subsystem (TIMES). Over 2600 hours of test time was accumulated. Results of these laboratory and system tests are presented in this paper.

Winkler, H. E.↗

NASA NTRS1984

The geochemical behavior of refractory noble metals and lithophile trace elements in refractory inclusions in carbonaceous chondrites

Recent models of Ca, Al-rich (CAI) inclusion petrogenesis, and the recent availability of thermodynamic data have led to the reexamination of the geochemical behavior of the refractory noble metals (RNM) and several lithophile refractory trace elements in CAI's in the context of distillation models. Here, pertinent chemical and mineralogical properties of the various classes of refractory inclusions are reviewed, and calculations of the stability of LRTE-RNM alloys and several LRTE oxides under nebular conditions are presented. The calculations, observations and experimental results are applied to a new model of the origin of refractory metal nuggets, and a specific mechanism is identified for producing Group II chemical patterns in a cold star nebula by fractionating interstellar dust at low temperature on the basis of physical differences between different populations of pre-solar grains.

Fegley, B., Jr.↗