Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dynamic phases”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Improved Magnetron Stability and Reduced Noise in Efficient Transmitters for Superconducting Accelerators

State of the art high-current superconducting accelerators require efficient RF sources with a fast dynamic phase and power control. This allows for compensation of the phase and amplitude deviations of the accelerating voltage in the Superconducting RF (SRF) cavities caused by microphonics, etc. Efficient magnetron transmitters with fast phase and power control are attractive RF sources for this application. They are more cost effective than traditional RF sources such as klystrons, IOTs and solid-state amplifiers used with large scale accelerator projects. However, unlike traditional RF sources, controlled magnetrons operate as forced oscillators. Study of the impact of the controlling signal on magnetron stability, noise and efficiency is therefore important. This paper discusses experiments with 2.45 GHz, 1 kW tubes and verifies our analytical model which is based on the charge drift approximation.

Kazakevich, G.↗

Scanning Josephson Tunneling Microscopy of Single Crystal Bi2Sr2CaCu2O8+delta with a Conventional Superconducting Tip

We have performed both Josephson and quasiparticle tunneling in vacuum tunnel junctions formed between a conventional superconducting scanning tunneling microscope tip and overdoped Bi2Sr2CaCu2O8+ single crystals. A Josephson current is observed with a peak centered at a small finite voltage due to the thermal-fluctuation-dominated superconducting phase dynamics. Josephson measurements at different surface locations yield local values for the Josephson ICRN product. Corresponding energy gap measurements were also performed and a surprising inverse correlation was observed between the local ICRN product and the local energy gap.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Molecular dynamics simulation of phase competition in terbium

The competition among multiple solid phases determines the final microstructures of a material. Such competition can originate at the very beginning of the solidification process. We report the results of molecular dynamics simulation of the phase competition between the hexagonal close-packed (hcp), face-centered cubic (fcc), and body-centered cubic (bcc) phases during the solidification of pure Tb. We found that the liquid supercooled below the hcp melting temperature has both bcc and hcp/fcc nuclei, but only the bcc nuclei grow such that the liquid always solidifies into the bcc phase, even at temperatures where the hcp phase is more stable. The hcp phase can only form in the last liquid droplet or at the bcc grain boundaries. Depending on the bcc grain orientations, the hcp phase jammed between the bcc grains either completely disappears or slowly grows via a solid-state massive transformation mechanism. Once the hcp phase becomes large enough, the stresses associated with its appearance can trigger a martensitic transformation. Yet, not the entire bcc phase is consumed by the martensitic transformation and the remaining bcc phase is transformed into the hcp phase via the solid-state massive transformation mechanism. If the supercooling is too large, the nucleation becomes almost barrier free and the liquid solidifies into a structure consisting of ultra-fine hcp and bcc grains after which the bcc phase quickly disappears.

36 MATERIALS SCIENCE↗

He II Liquid/Vapor Phase Separator for Large Dynamic Range Operation

A phase separator, which separates helium vapor from liquid superfluid helium (He II), is an indispensable device for space cryogenics. The most recent approach to the Space Infrared Telescope Facility (SIRTF) uses a new design concept in which only the detector package is cold at launch, the remainder of the telescope being subsequently cooled to operating temperature on orbit. Therefore, a large dynamic operational range is required of the cryogen system. This is a report of initial laboratory test results with candidate porous plugs as phase separators. Mass flow rates and pressure and temperature differences across a porous plug were measured in this experiment. Relatively large mass flow rates were observed even at small pressure differences. In the high mass flow rate region, a hysteresis was observed with increases and decreases of the pressure difference. A linear theory is proposed and compared with experimental data to explain several phenomena observed in this system.

Phase Separator, Space Cryogenics↗

Multijunction Ga 0.5 In 0.5 P/GaAs solar cells grown by dynamic hydride vapor phase epitaxy

We report the development of Ga 0.5 In 0.5 P/GaAs monolithic tandem solar cells grown by dynamic hydride vapor phase epitaxy, a III-V semiconductor growth alternative to metalorganic vapor phase epitaxy with the potential to reduce growth costs. The tandem device consists of 3 components: a 1.88 eV band gap (E G ) Ga 0.5 In 0.5 P top cell, a p-Ga 0.5 In 0.5 P/n-GaAs tunnel junction, and a 1.41 eV rear heterojunction GaAs cell. The open circuit voltage (VOC) and fill factor are 2.40 V and 88.4%, respectively, indicative of high material quality. Electroluminescence measurements show that the individual V OC of the top and bottom cell are 1.40 and 1.00 V, respectively, yielding EG-voltage offsets (W OC ) of 0.48 and 0.41 V. The W OC of the top cell is higher because of an unpassivated front surface rather than the bulk material quality. The Ga 0.5 In 0.5 P top cell limits the current of this series-connected device for this reason to a short-circuit current density (JSC) of 11.16 +/- 0.15 mA/cm 2 yielding an overall efficiency of 23.7% +/- 0.3%. We show through modeling that thinning the emitter will improve the present result, with a clear pathway toward 30% efficiency with the existing material quality. This result is a promising step toward the realization of high-efficiency III-V multijunction devices with reduced growth cost.

14 SOLAR ENERGY↗

In-Situ Characterization of Dynamic Morphological and Phase Changes of Selenium-doped Germanium Using a Single Particle Cell and Synchrotron Transmission X-ray Microscopy

The dynamic information of lithium-ion battery active materials obtained from coin cell-based in-situ characterizations might not represent the properties of the active material itself because many other factors in the cell could have impacts on the cell performance. To address this problem, a single particle cell was developed to perform the in-situ characterization without the interference of inactive materials in the battery electrode as well as the X-ray-induced damage. In this study, the dynamic morphological and phase changes of selenium-doped germanium (Ge 0.9 Se 0.1 ) at the single particle level were investigated via synchrotron-based in-situ transmission X-ray microscopy. The results demonstrate the good reversibility of Ge 0.9 Se 0.1 at high cycling rate that helps understand its good cycling performance and rate capability. This in-situ and operando technique based on a single particle battery cell provides an approach to understanding the dynamic electrochemical processes of battery materials during charging and discharging at the particle level.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Graphics processing unit accelerated phase field dislocation dynamics: Application to bi-metallic interfaces

We present the first high-performance computing implementation of the meso-scale phase field dislocation dynamics (PFDD) model on a graphics processing unit (GPU)-based platform. The implementation takes advantage of the portable OpenACC standard directive pragmas along with Nvidia's compute unified device architecture (CUDA) fast Fourier transform (FFT) library called CUFFT to execute the FFT computations within the PFDD formulation on the same GPU platform. The overall implementation is termed ACCPFDD-CUFFT. The package is entirely performance portable due to the use of OPENACC-CUDA inter-operability, in which calls to CUDA functions are replaced with the OPENACC data regions for a host central processing unit (CPU) and device (GPU). A comprehensive benchmark study has been conducted, which compares a number of FFT routines, the Numerical Recipes FFT (FOURN), Fastest Fourier Transform in the West (FFTW), and the CUFFT. The last one exploits the advantages of the GPU hardware for FFT calculations. The novel ACCPFDD-CUFFT implementation is verified using the analytical solutions for the stress field around an infinite edge dislocation and subsequently applied to simulate the interaction and motion of dislocations through a bi-phase copper-nickel (Cu–Ni) interface. It is demonstrated that the ACCPFDD-CUFFT implementation on a single TESLA K80 GPU offers a 27.6X speedup relative to the serial version and a 5X speedup relative to the 22-multicore Intel Xeon CPU E5-2699 v4 @ 2.20 GHz version of the code.

97 MATHEMATICS AND COMPUTING↗

Water Dynamics in Gyroid Phases of Self-Assembled Gemini Surfactants

Water-mediated ion transport through functional nanoporous materials depends on the dynamics of water confined within a given nanostructured morphology. In this study, we investigate hydrogen-bonding dynamics of interfacial water within a ‘normal’ (Type I) lyotropic gyroid phase formed by a gemini dicarboxylate surfactant self-assembly using a combina- tion of 2DIR spectroscopy and molecular dynamics simulations. Experiments and simulations demonstrate that water dynamics in the normal gyroid phase is one order of magnitude slower than that in bulk water, due to specific interactions between water, the ionic surfactant headgroups, and counterions. However, the dynamics of water in the normal gyroid phase are faster than those of water confined in a reverse spherical micelle of a sulfonate surfactant, given that the water pool in the reverse micelle and the water pore in the gyroid phase have roughly the same diameters. This difference in confined water dynamics likely arises from the significantly reduced curvature- induced frustration at the convex interfaces of the normal gyroid, as compared to the concave interfaces of a reverse spherical micelle. These detailed insights into confined water dynamics may guide the future design of artificial membranes that rapidly transport protons and other ions.

36 MATERIALS SCIENCE↗

GaAs growth rates of 528 μm/h using dynamic-hydride vapor phase epitaxy with a nitrogen carrier gas

Herein we demonstrate record GaAs growth rates approaching 530 μm/h using nitrogen carrier gas and 400 μm/h using hydrogen carrier gas in a dynamic-hydride vapor phase epitaxy reactor. We measured root mean square surface roughness below 1 nm using a 1 μm × 1 μm atomic force microscopy scan for GaAs growth rates up to 483 μm/h using a nitrogen carrier gas and 400 μm/h using a hydrogen carrier gas. We performed computational fluid dynamics modeling to study the effect of the carrier gas choice on the thermal profile within the reactor and how that influences the degree of AsH 3 decomposition. The modeling suggests that the lower thermal conductivity of the nitrogen carrier gas minimizes the amount of AsH 3 that thermally decomposes before reaching the wafer surface and the heavier atomic mass decreases the likelihood that AsH 3 will reach the heated reactor walls, leading to a growth rate enhancement relative to the hydrogen carrier case in a hydride-enhanced growth regime.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Doping Density on the Performance of Metamorphic GaInAs Solar Cells Grown by Dynamic Hydride Vapor Phase Epitaxy

We study the effect of doping density on the performance of inverted metamorphic ~1 eV GaInAs solar cells grown by dynamic hydride vapor phase epitaxy. We find that the doping efficiency of Se in this material is extremely high, with 5x10 17 cm -3 being the lowest controlled value we could achieve with our present Se source. We compared rear heterojunction devices grown with intentional n-doping of 5x10 17 cm -3 and unintentional n-doping of 5x10 15 cm -3 . The intentionally doped sample exhibited an open circuit voltage ~80 mV higher than the unintentionally doped sample due to reduced dark current, and a bandgap voltage offset, or W OC , of 0.407 V. We believe that future doping optimization will improve carrier collection and W OC in these devices.

GaAs↗

Pulse current auxiliary forging of sintered TiAl alloys based on the investigation of dynamic recrystallization and phase transformation

Highlights: • DRX kinetics model of sintered near γ TiAl alloy was established. • DRX process was accompanied by twinning when compressed at 1125 °C/0.1 s{sup − 1}. • Hot deformation has a promotion to the phase transformation of γ → α. - Abstract: Pulse current auxiliary forging is a new and efficient way to fabricate high performance TiAl based alloys. Dynamic recrystallization (DRX) and phase transformation have a pronounced effect on the subsequent deformability of TiAl based alloys. Hence, the dynamic recrystallization kinetics were determined at the temperature range of 1125–1275 °C and strain rate range of 0.1–0.001 s{sup − 1}. In addition, the DRX mechanism and phase transformation of TiAl based alloys were investigated to model the microstructure evolution in order to provide guidance for the pulse current auxiliary forging process. When the specimens were compressed at 1125 °C/0.1 s{sup − 1}, twinning played an important role in the DRX process. With increasing deformation temperature, the microstructure transformed from near gamma into duplex microstructure. In addition, according to the kinetics of dynamic recrystallization and phase transformation, fully DRXed TiAl based alloys were fabricated through pulse current auxiliary forging. The as-forged TiAl-based alloys show good superplastic performance with an elongation over 410%.

36 MATERIALS SCIENCE↗

Dynamics of the phase transitions in the system of nonequilibrium charge carriers in quantum-dimensional Si{sub 1−x}Ge{sub x}/Si structures

The dynamics of the phase transition from an electron-hole plasma to an exciton gas is studied during pulsed excitation of heterostructures with Si{sub 1−x}Ge{sub x}/Si quantum wells. The scenario of the phase transition is shown to depend radically on the germanium content in the Si{sub 1−x}Ge{sub x} layer. The electron-hole system decomposes into a rarefied exciton and a dense plasma phases for quantum wells with a germanium content x = 3.5% in the time range 100–500 ns after an excitation pulse. In this case, the electron-hole plasma existing in quantum wells has all signs of an electron-hole liquid. A qualitatively different picture of the phase transition is observed for quantum wells with x = 9.5%, where no separation into phases with different electronic spectra is detected. The carrier recombination in the electron-hole plasma leads a gradual weakening of screening and the appearance of exciton states. For a germanium content of 5–7%, the scenario of the phase transition is complex: 20–250 ns after an excitation pulse, the properties of the electron-hole system are described in terms of a homogeneous electron-hole plasma, whereas its separation into an electron-hole liquid and an exciton gas is detected after 350 ns. It is shown that, for the electron-hole liquid to exist in quantum wells with x = 5–7% Ge, the exciton gas should have a substantially higher density than in quantum wells with x = 3.5% Ge. This finding agrees with a decrease in the depth of the local minimum of the electron-hole plasma energy with increasing germanium concentration in the SiGe layer. An increase in the density of the exciton gas coexisting with the electron-hole liquid is shown to enhance the role of multiparticle states, which are likely to be represented by trions T{sup +} and biexcitons, in the exciton gas.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A phase field dislocation dynamics model for a bicrystal interface system: An investigation into dislocation slip transmission across cube-on-cube interfaces

In this study, we present a phase field dislocation dynamics formulation designed to treat a system comprised of two materials differing in moduli and lattice parameters that meet at a common interface. We apply the model to calculate the critical stress τ crit required to transmit a perfect dislocation across the bimaterial interface with a cube-on-cube orientation relationship. The calculation of τ crit accounts for the effects of: 1) the lattice mismatch (misfit or coherency stresses), 2) the elastic moduli mismatch (Koehler forces or image stresses), and 3) the formation of the residual dislocation in the interface. Our results show that the value of τ crit associated with the transmission of a dislocation from material 1 to material 2 is not the same as that from material 2 to material 1. Dislocation transmission from the material with the lower shear modulus and larger lattice parameter tends to be easier than the reverse and this apparent asymmetry in τ crit generally increases with increases in either lattice or moduli mismatch or both. In efforts to clarify the roles of lattice and moduli mismatch, we construct an analytical model for τcrit based on the formation energy of the residual dislocation. We show that path dependence in this energetic barrier can explain the asymmetry seen in the calculated τ crit values.

36 MATERIALS SCIENCE↗

Dynamic Hydride Vapor Phase Epitaxy (D-HVPE) as a Route to Inexpensive, High-Performance III-V Materials and Devices

This work describes the recent development of Dynamic Hydride Vapor Phase Epitaxy (D-HVPE), which extends the standard HVPE process to allow for the deposition of relatively complex heterostructures and devices at growth rates in excess of 300 um/h. This process uses low-cost elemental metal precursors, and uses all of the reactants efficiently to create high-performance devices. D-HVPE also lends itself to potential in-line growth, which when combined with the low-cost precursors and extremely fast growth rates for high-quality III-V materials, can lead to significantly lower epitaxial growth costs. Here, we focus on the growth of high-efficiency photovoltaics as an example device to show the capabilities of the D-HVPE growth process.

14 SOLAR ENERGY↗

Sliding dynamics for bubble phases on periodic modulated substrates

We analyze a bubble-forming system composed of particles with competing long-range repulsive and short-range attractive interactions driven over a quasi-one-dimensional periodic substrate. We find various pinned and sliding phases as a function of substrate strength and drive amplitude. When the substrate is weak, a pinned bubble phase appears that depins elastically into a sliding bubble lattice. For stronger substrates, we find anisotropic bubbles, disordered bubbles, and stripe phases. Plastic depinning occurs via the hopping of individual particles from one bubble to the next in a pinned bubble lattice, and as the drive increases, there is a transition to a state where all of the bubbles are moving but are continuously shedding and absorbing individual particles. This is followed at high drives by a moving bubble lattice in which the particles can no longer escape their individual bubbles. The transition between the plastic and elastic sliding phases can be detected via signatures in the velocity-force curves, differential conductivity, and noise. When the bubbles shrink due to an increase in the attractive interaction term, they fit better inside the pinning troughs and become more strongly pinned, leading to a reentrant pinning phase. For weaker attractive terms, the size of the bubbles becomes greater than the width of the pinning troughs and the depinning becomes elastic with a reduced depinning threshold. Published by the American Physical Society 2024

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Observation of dynamic equilibrium cluster phase in nanoparticle-polymer system

Small-angle neutron scattering (SANS) and dynamic light scattering (DLS) have been used to investigate the existence of a cluster phase in a nanoparticle-polymer system. The nanoparticle-polymer system shows an interesting reentrant phase behavior where the charge stabilized silica nanoparticles undergo particle clustering and back to individual nanoparticles as a function of polymer concentration. This kind of phase behavior is believed to be directed by opposing attractive and repulsive interactions present in the system. The phase behavior shows two narrow regions of polymer concentration immediately before and after the two-phase formation indicating the possibility of the existence of some equilibrium clusters. DLS results show a much higher size of particles than individuals in these two regions which remains unchanged even after dilution. The SANS data show the evolution of attraction with increased volume fraction of the particles supporting the dynamic nature of these clusters.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Dynamical revival of phase coherence in a many-boson system

We study the quantum dynamics of cold Bose atoms in a double well. It is shown that self-trapping as well as population oscillations are common phenomena associated with nonlinear interactions. For larger U/t, multiparticle tunneling is damped and the quantum dynamics is dominated by single-particle tunneling. The many-body system can be effectively described in a truncated Fock space. It exhibits coherence-decoherence oscillations in the temporal evolution. We predict an interesting phenomenon of dynamical revival and collapse of matter wave fields in optical lattices in regimes near the superfluid-Mott-insulator phase boundary.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗