Search NASA⌕ Search

SEARCH · Search NASA

Results for “ELONGATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Low temperature mechanical properties, fractographic and metallographic evaluation of several alloy steels

The mechanical properties are presented of alloy steels, 4130, 4140, 4340, 6150, and 8740. Test specimens were manufactured from approximately 1.00 inch (2.54 cm) diameter bar stock which had been heat treated to two different hardness levels. The following mechanical tests were performed at temperatures of 80 F (+26.7 C), 0 F (-17.8 C), -100 F (-73 C), and -200 F (-129 C): (1) tensile test (Ultimate, yield, modulus, elongation, and reduction of area), (2) notched tensile test, (3) charpy V-notched impact test (impact energy), and (4) double shear strength test (ultimate and yield). The test data indicate excellent tensile strength, notched/unnotched tensile ratios, ductility, impact, and shear properties at all test temperatures, except at -200 F (-129 C) where the impact strength of the higher strength group of alloy steels, 4130 (Rc-37) and 4140 (Rc-44) decreased to approximately 9 ft. lbs. (12 joules) and 6 ft. lbs. (8 joules), respectively. Chemical, metallographic, and fractographic analyses were also performed to evaluate microstructure, microhardness and the effect of decrease in temperature on the ductile to brittle failure transition.

Montano, J. W.↗
NASA NTRS1973

Gas turbine exhaust nozzle

An elongated hollow string is disposed in an exhaust nozzle combustion chamber and communicates with an air source through hollow struts at one end. The other end of the string is bell-mouth shaped and extends over the front portion of a nozzle plug. The bell-mouth may be formed by pivotally mounted flaps or leaves which are used to vary the exhaust throat area and the area between the plug and the leaves. Air from the engine inlet flows into the string and also between the combustion chamber and a housing disposed around the chamber. The air cools the plug and serves as a low velocity inner core of secondary gas to provide noise reduction for the primary exhaust gas while the other air, when it exits from the nozzle, forms an outer low velocity layer to further reduce noise. The structure produces increased thrust in a turbojet or turbofan engine.

Straight, D. M.↗
NASA NTRS1974

Structural lineaments in the southern Sierra Nevada, California

The author has identified the following significant results. Several lineaments observed in ERTS-1 MSS imagery over the southern Sierra Nevada of California have been studied in the field in an attempt to explain their geologic origins and significance. The lineaments are expressed topographically as alignments of linear valleys, elongate ridges, breaks in slope or combinations of these. Natural outcrop exposures along them are characteristically poor. Two lineaments were found to align with foliated metamorphic roof pendants and screens within granitic country rocks. Along other lineaments, the most consistant correlations were found to be alignments of diabase dikes of Cretaceous age, and younger cataclastic shear zones and minor faults. The location of several Pliocene and Pleistocene volcanic centers at or near lineament intersections suggests that the lineaments may represent zones of crustal weakness which have provided conduits for rising magma.

Liggett, M. A.↗
NASA NTRS1974

Heat transfer device

A heat transfer device is characterized by an hermetically sealed tubular housing including a tubular shell terminating in spaced end plates, and a tubular mesh wick concentrically arranged and operatively supported within said housing. The invention provides an improved wicking restraint formed as an elongated and radially expanded tubular helix concentrically related to the wick and adapted to be axially foreshortened and radially expanded into engagement with the wick in response to an axially applied compressive load. The wick is continuously supported in a contiguous relationship with the internal surfaces of the shell.

Kalkbrenner, R. W.↗
NASA NTRS1974

Effects of simulated space environment on Skylab parasol material

A material consisting of ripstop nylon bonded to the Mylar side of aluminized Mylar film was used to construct the first Skylab parasol. The mechanical properties of elongation and tensile strength and the radiative properties of solar absorptance and thermal emittance were measured before and after exposure to simulated solar radiation at intensities of 1.0 and 3.5 solar constants for exposure times as long as 947 hours or 3316 equivalent solar hours. The accelerated testing indicated more severe degradation than was experienced in the real-time test (1 solar constant). The results predicted that this material could have given satisfactory performance throughout the planned lifetime of the Skylab workshop.

Slemp, W. S.↗
NASA NTRS1974

Means for accommodating large overstrain in lead wires

An electrical wire is reported along whose length loops are formed at intervals and retained in a plastic capsule that allows unfolding of the loop when tension is exerted on the opposite ends of the wire. The capsule is formed by encompassing each loop with a sleeve of heat shrinkable synthetic plastic material which overlaps the loop and heat shrinking the overlapping portions. Thus, a length of electrical wire is formed which stores extra lengths of wire in the quantity needed to match the expected stretching of materials or elements such as ropes, cords and the like of high elongation to which the electrical wire may be attached.

Rumble, C. V.↗
NASA NTRS1974

Effects of sigma-phase formation on some mechanical properties of a wrought nickel-base superalloy (IN-100)

The effect of sigma phase formation on an extruded and forged nickel base superalloy with the composition of the casting alloy IN-100 was studied. By adding only aluminum and titanium to remelt stock, three compositions were produced which had varying propensities for sigma formation. These compositions were given a four step heat treatment and were stress-ruptured or tensile tested. The very sigma prone composition had a shorter rupture life than the sigma-free or moderately sigma prone compositions when tested at 843 and 885 C. Elongation in room temperature tensile tests was considerably lower for the very sigma prone composition than for the other two wrought compositions after prolonged exposure at 732 or 843 C.

Dreshfield, R. L.↗
NASA NTRS1974

Sound radiation from a high speed axial flow fan due to the inlet turbulence quadrupole interaction

A formula is obtained for the total acoustic power spectra radiated out the front of the fan as a function of frequency. The formula involves the design parameters of the fan as well as the statistical properties of the incident turbulence. Numerical results are calculated for values of the parameters in the range of interest for quiet fans tested at the Lewis Research Center. As in the dipole analysis, when the turbulence correlation lengths become equal to the interblade spacing, the predicted spectra exhibit peaks around the blade passing frequency and its harmonics. There has recently been considerable conjecture about whether the stretching of turbulent eddies as they enter a stationary fan could result in the inlet turbulence being the dominant source of pure tones from nontranslating fans. The results of the current analysis show that, unless the turbulent eddies become quite elongated, this noise source contributes predominantly to the broadband spectrum.

Goldstein, M. E.↗
NASA NTRS1974

Coaxial anode wire for gas radiation counters

The design and characteristics of a gas radiation counter are discussed. The coaxial anode consists of an elongated central wire covered with an electrically insulating sleeve. Several longitudinally discontinuous segments of an electrically conductive coating are disposed about the insulating sleeve in a coaxial pattern along the length of the central wire. The conductive coating segments form a veto or rejection anode at each end of the central wire and a main or primary charge detecting anode between the ends. The segments are coupled together so that the primary charge detecting anode is connected to detection circuitry in anti-coincidence with the veto anodes. Background radiation detected by either of the veto anodes and the primary charge detecting anode is rejected and the sensitivity of the radiation counter device is increased.

Kraushaar, W. L.↗
NASA NTRS1973

Property investigation and sputter deposition of dispersion-hardened copper for fatigue specimen fabrication

Sputter-deposited alloys of dispersion-hardenable Cu-0.25 vol% SiC and Cu-0.50 vol% SiC and precipitation-hardenable Cu-0.15 wt% Zr and Cu-0.05 wt% Mg-0.15 wt% Zr-0.40 wt% Cr were investigated for selection to evaluate fatigue specimen performance with potential application in fabricating regeneratively cooled rocket thrust chambers. Yield strengths in the 700 to 1000-MN/sq m range were observed with uniform elongation ranging from 0.5 to 1.5% and necking indicative of greater ductility. Electrical conductivity measured as an analog to thermal conductivity gave values 90% IACS for Cu-0.15 wt% Zr and Cu-0.05 wt% Mg-0.15 wt% Zr-0.40 wt% Cr. A 5500-g sputtered deposit of Cu-0.15 wt% Zr alloy, 12.29 mm (0.484 in.) average thickness in the fatigue specimen gage length, was provided to NASA on one of their substrates.

Mcclanahan, E. D.↗
NASA NTRS1974

Heat flow calorimeter

Heat flow calorimeter devices are used to measure heat liberated from or absorbed by an object. This device is capable of measuring the thermal output of sealed nickel-cadmium batteries or cells during charge-discharge cycles. An elongated metal heat conducting rod is coupled between the calorimeter vessel and a heat sink, thus providing the only heat exchange path from the calorimeter vessel itself.

Fletcher, J. C.↗
NASA NTRS1974

Users manual: Dynamics of two bodies connected by an elastic tether, six degrees of freedom forebody and five degrees of freedom decelerator

The equations of motion and a computer program for the dynamics of a six degree of freedom body joined to a five degree of freedom body by a quasilinear elastic tether are presented. The forebody is assumed to be a completely general rigid body with six degrees of freedom; the decelerator is also assumed to be rigid, but with only five degrees of freedom (symmetric about its longitudinal axis). The tether is represented by a spring and dashpot in parallel, where the spring constant is a function of tether elongation. Lagrange's equation is used to derive the equations of motion with the Lagrange multiplier technique used to express the constraint provided by the tether. A computer program is included which provides a time history of the dynamics of both bodies and the tension in the tether.

Doyle, G. R., Jr.↗
NASA NTRS1974

Skylab M551 Metals Melting Experiment

The objectives of the M551 Metals Melting Experiment are to (a) study behavior of molten metal, (b) characterize metals melted and solidified in the low gravity space environment compared to one-gravity of earth, and (c) determine feasibility of joining metals in space. The experiment used the electron beam (EB) and chamber of the M512 apparatus to make a dwell puddle and a melt in a rotating disc of varying thickness. Hence, the EB performed cut-through, full and partial penetration melts, in addition to a re-solidified button. The three disc materials were aluminum 2219-T87, 304 stainless steel and pure tantalum to provide a wide range of density and melting conditions. Observations to date include (a) the proof that EB welding, cutting and melting can be done successfully in low gravity. Earlier, some welding authorities had postulated that without gravity the EB would force the molten puddle out of contact. However, the experiment proved that surface tension forces predominate. (b) From the view-point of cast-solidification, small, equiaxed grains in Skylab specimens compared to large, elongated grains in ground-based specimens were observed. The former are thought to be associated with constitutional supercooling and nucleation where the latter are associated with dendritic solidification. In further support of the more equiaxed grain growth in Skylab, symmetric sub-grain patterns were frequently observed where there was much less symmetry in ground-based specimens. Further work is being done to explain the differences in solidification.

E C Mckannan↗
NASA NTRS1972

Detection and analysis of Jupiter's decametric micropulses

The occurrence of Jupiter's decametric radio emission can be correlated with the central meridian longitude of Jupiter as if the active regions were radio transmitters placed at fixed longitudes on its surface. These active regions are commonly called sources and are labelled Source A, Jovian longitude = 200 deg, Source B = 100 deg and Source C =300 deg. These sources are not always active. However, they can be turned-on if Jupiter's innermost Galilean moon, Io, is in the right phase. In fact, if Io is found 90 deg from superior geocentric conjunction (maximum eastern elongation) and if source B is simultaneously on the central meridian, source B radiation is almost guaranteed, whereas source C radiation is highly likely when Io is found 240 deg from superior geocentric conjunction. Source A radiation is largely independent of Io's position. Interestingly, the Io-related radio storms contain unusually rapid events that can only be properly studied using wide-band techniques.

Lebo, G. R.↗
NASA NTRS1974

The use of ERTS-1 images in the search for large sulfide deposits in the Chagai District, Pakistan

The author has identified the following significant results. Visual examination of color composites was tested under relatively ideal conditions for direct detection of large hydrothermal sulfide deposits at the low-grade porphyry copper deposit at Saindak, western Chagai District, Pakistan. The Saindak deposit is characterized by an elongate zone of easily eroded sulfide-rich rock surrounded by a resistant rim of hornfels and propylitically altered rock. The geomorphic features related to the Saindak deposit are easily distinguished on ERTS-1 images. Attempts to detect a color anomaly using false-color composites were not successful. About 36,000 square km of the western Chagai District were examined on false-color composites for direct evidence of large sulfide deposits. New geologic information acquired from the images was used in conjunction with the known geology to evaluate two previously known proposed areas and to suggest seven additional targets for field checking, one of which is proposed on the basis of tonal anomaly alone. The study also showed that Saindak-type deposits are not likely to be present in some extensive areas of the Chagai District; and also that a rim like that at Saindak does not form if regional metamorphism has increased the resistance of the country rock to erosion.

Schmidt, R. G.↗
NASA NTRS1974

Tool for use in lifting pin supported objects

A tool for use in lifting a pin-supported, electronic package mounted in juxtaposition with the surface of an electronic circuit board is described. The tool is configured to be received beneath a pin-supported package and is characterized by a manually operable linkage, including an elongated, rigid link is supported for axial reciprocation and a pivotal link pinned to the body and supported for oscillation induced in response to axial motion imparted to the rigid link. A lifting plate is pivotally coupled to the distal end of the pivotal link so that oscillatory motion imparted to the pivotal link serves to move the plate vertically for elevating the plate into lifting engagement with the electronic package positioned thereabove.

Marzek, R. A.↗
NASA NTRS1974

High-temperature strength stability of three forms of chemically vapor deposited tungsten

Three types of CVD tungsten (fluoride-produced, chloride-produced, and a layered composite of the two-termed duplex) were evaluated to determine their high-temperature strength and microstructural stability following 5000-hr exposure to temperatures of 1540 and 1700 C. At the highest temperatures investigated (1540 and 1700 C), the tensile strengths of the two basic materials were essentially equal. At lower temperatures, chloride tungsten possessed lower yield strength but higher ultimate strength than fluoride tungsten while the behavior of the duplex material was generally intermediate. Apparent anomalies in high-temperature elongation behavior are explained on the basis of grain boundary cavity formation and recrystallization. The grain size of fluoride tungsten changed only slightly following 5000-h treatment at 1700 C. In contrast, chloride tungsten possessed both poor resistance to grain growth and an accompanying relatively high ductile-brittle transition temperature.

Bryant, W. A.↗
NASA NTRS1974

Zodiacal light and the asteroid belt - The view from Pioneer 10

Brightnesses measured by the Pioneer 10 imaging photopolarimeter in two regions of sky were compared on sky maps at sun-spacecraft distances from 2.4 to 4.8 AU to determine the spatial extent of the zodiacal light. Data in the ecliptic at elongations greater than 90 deg show negligible contribution to the zodiacal light beyond 3.3 AU, the 2:1 Jupiter resonance. The zodiacal light brightness at 2.4 AU is less than 10% of that observed at 1 AU.

Hanner, M. S.↗