Search NASA⌕ Search

SEARCH · Search NASA

Results for “Effective thermal conductivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Investigation of fouling mechanisms for diesel engine exhaust heat recovery

The effect of diesel engine exhaust fouling on heat and mass exchangers for waste heat recovery is investigated. Experiments are conducted for a range of operating conditions relevant to the use of the waste heat from a diesel engine for powering a 2.71 kW capacity absorption heat pump. Thermal resistances of fouling layers as well as their effects on pressure drop are determined, and the underlying mechanisms for deposition and removal are investigated. Fouling layer effects are most severe for the lowest coolant temperatures and 100% generator load. At these conditions, the fouling thermal resistance is approximately 70% of the total resistance, and the ratio of the steady-state pressure drop to the baseline pressure drop is 3.25. Flow induced shear is found to be the primary growth inhibiting mechanism at high exhaust velocities. Findings from this study can guide heat exchanger design for a variety of waste heat recovery systems.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2025

Effect of toolpath in large-format additive manufacturing with bio-derived composites

There has been growing interest in integrating bio-derived composites into Large-format additive manufacturing (LFAM) feedstocks to reduce the use of petroleum-derived materials and reduce the overall carbon footprint of LFAM. However, these materials present unique challenges during manufacturing due to their variability, which can lead to unintended deformations and failures attributable to suboptimal process conditions. While numerical modelling has been extensively employed to simulate numerous manufacturing processes, its application in LFAM with bio-derived composites remains limited. This study addresses this gap by systematically developing a numerical model to simulate the LFAM process using bio-based materials, specifically wood fiber-reinforced polylactic acid (PLA/WF). Experimental investigations were conducted to characterise the thermal and mechanical properties of additively manufactured PLA/WF specimens. Numerical simulations were performed to predict temperature profiles and deformations during LFAM. The effect of varying infill patterns, internal structures, and tool paths on the temperature distribution and deformation of printed parts was explored using the developed model. This article aims to advance the utilisation of bio-derived composites in LFAM systems and provide a comprehensive understanding of the LFAM process. The findings offer valuable insights for optimising process parameters and enhancing the performance of LFAM with bio-based composites.

Large-format additive manufacturing↗
DOE OSTI2024

Thermal performance of phase change materials with anisotropic carbon fiber inserts

In thermal energy storage systems, phase change materials (PCMs) are widely used for thermal energy management. Most PCMs have low thermal conductivities, which limits the heat transfer rate within PCM and thus makes the phase-changing process very slow. However, thermal conductivities of PCMs can be altered by inserting targeted additives. We hypothesize that the size and shape of these additive inserts play a key role in thermal management efficiency. To this end, the impacts of carbon fiber (CF) inserts on the phase change behavior and consequent heat transfer efficiencies of inorganic and organic PCMs were investigated using experiments and simulations. Long, anisotropic CFs with high thermal conductivities formed continuous fast heat flux tunnels inside PCMs to enhance the heat transfer. Such CFs could extend the phase change fronts from the limited container-shaped interface to the larger surface of numerous CF inserts inside the PCM. These special CF inserts work with a new heat transfer mechanism, different from conventional small additives or long isotropic CF inserts. The thermal energy release rate increased by 2.5 times with 1 wt.% anisotropic CF inserts in inorganic PCM. However, CF inserts in liquid organic PCM hindered the natural convection and compromised the improved heat conduction. In conclusion, the lab-scale multiphysics simulations support these experimental observations and indicate that CF inserts have potential to enhance heat transfer in inorganic PCMs, but they are less effective in organic PCMs.

25 ENERGY STORAGE↗
DOE OSTI2022

Impacts of Bond Type and Grafting Density on the Thermal, Structural, and Transport Behaviors of Nanoparticle Organic Hybrid Materials–Based Electrolytes

Nanoscale Organic Hybrid Materials (NOHMs) consist of polymers tethered to a nanoparticle surface, and NOHMs formed with an ionic bond between the polymer and nanoparticle have been proposed for electrochemical applications. NOHMs exhibit negligible vapor pressure, chemical tunability, oxidative thermal stability, and high ionic conductivity making them attractive in reactive and separation systems. In this study, NOHMs are synthesized by tethering Jeffamine M2070 (HPE) to SiO 2 nanocores via ionic (NOHM-I-HPE) and covalent (NOHM-C-HPE) bonding to investigate the effect of the bond type on the thermal, structural and transport properties of the tethered HPE. In the neat state, NOHM-C-HPE displays the highest thermal stability in a nitrogen atmosphere, while NOHM-I-HPE is the most stable under oxidative conditions. Small-angle neutron scattering (SANS) reveals the presence of multiple types of HPE polymers in aqueous solutions of NOHM-I-HPE (i.e., tethered, interacting, and free), whereas only tethered HPE is observed in NOHM-C-HPE systems. Moreover, the SANS profiles identify clustering of NOHM-C-HPE in aqueous solutions, but not in the corresponding NOHM-I-HPE solutions, suggesting that the free HPE chains stabilize the dispersion of NOHM-I-HPE. Furthermore, the results of this study elucidate how the bond type and grafting density can be used to tune the properties of NOHMs.

25 ENERGY STORAGE↗
DOE OSTI2023

New Zintl Phase Yb 10 MgSb 9 with High Thermoelectric Performance

Abstract Yb 10 MgSb 9 is a new Zintl compound (with a composition closer to Yb 10.5 MgSb 9 ) and a promising thermoelectric material first reported in this work. Undoped Yb 10 MgSb 9 has an ultralow thermal conductivity due to crystallographic complexity and exhibits a relatively high peak p‐type Seebeck coefficient and high electrical resistivity. This is consistent with Zintl counting and density functional theory (DFT) calculations that the composition Yb 10.5 MgSb 9 should be a semiconductor. Na is found experimentally to be an effective p‐type dopant potentially due to the replacement of Na + for Yb 2+ , allowing for a significant decrease in electrical resistivity. With doping, a dramatic improvement of electrical conductivity is observed and the glass‐like thermal conductivity remains low, allowing for a significant enhancement of the thermoelectric figure of merit, zT . Doping increases the zT from 0.23 in undoped Yb 10 MgSb 9 to 1.06 in 7 at% Na‐doped Yb 10 MgSb 9 at 873K. This high thermoelectric performance found through Na‐doping places this material amongst the leading p‐type Zintl thermoelectrics, making it a promising candidate for future studies and high‐temperature thermoelectric applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Thermal shock resistance of lightweight cements developed for geothermal conditions

Cements are a critical component in well construction, as they act to prevent well fluid and gas escape, prevent corrosion of the casing, and strengthen the wellbore to prevent deformation. Under the high temperature/pressure conditions common in geothermal systems, the injection of cold water for energy production is expected to induce cyclic damage to the borehole cement through the rapid temperature fluctuations. These “thermal shocks” are expected to cause casing shrinkage, annulus formation, and cement tensile stresses. To understand the effect of cold water injection on the wellbore environment, a set of rock-cement-steel samples were created to simulate the structure of a geothermal well. Lightweight thermally-insulating cement blends were tested under thermal shock conditions in this study. In each test, the samples were pressurized to an effective pressure of ~3.5 MPa and placed at high temperatures. Thermal shocks were performed by injecting cold water (~10-15 °C) through the samples at a constant rate while keeping the samples at high temperatures until the sample temperature stopped decreasing and deformation ceased. Eight thermal shock tests were conducted with each sample – two at 100 °C and six at 200 °C. Post-tests analysis was then conducted by cutting open each sample to examine the damage in each component of the simulated wellbore. Experimental results suggest that all samples experienced similar degrees of axial and lateral contraction during cold water injection, but for the most part this contraction is recoverable when injection halts. Post-test analysis revealed that fly ash cenosphere pre-treatment had the best effect on improving thermal shock resistance in the cement blends. Thermomechanical modeling of likely stress paths experienced by the cements during heating/cooling cycles shows that elasto-plastic cement constitutive behavior results in most plastic strain occurring during the initial heating steps, with mostly elastic strain occurring during the thermal shock cycles. In conclusion, this agrees with experimental evidence, suggesting that cement damage from shocking occurs via other mechanisms such as chemical alteration, corrosion, and fatigue.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Temperature Effects on Interdiffusion of Al and U-Mo under Irradiation

A high-energy Xe ion irradiation experiment was conducted to investigate the temperature dependence of interdiffusion in bilayer Al-UMo samples under irradiation. The amount of interdiffusion achieved at a fixed dose with the increase of temperature showed a clear transition at 175 degrees C (with an estimated error in the range of ± 10 degrees C) from temperature-independent to temperature-dependent behavior. The activation energy derived from the curve of interdiffusion quantity vs. irradiation temperature is 0.77 ± 0.16 eV. This information has been utilized to understand the temperature effect on the interdiffusion process that occurred at the interfaces of U-Mo particles and the Al matrix in U-Mo/Al dispersion fuels, whose magnitude significantly impacts the fuel's performance. Although this temperature effect was deemed important, it cannot be examined directly using in-pile irradiation data, as fuel temperatures cannot be measured in reactor irradiation and are highly correlated with fission rate and thermal conductivity evolution. To connect the knowledge accumulated from ion irradiation with in-pile irradiation data, simulation of a full-sized U-Mo/Al dispersion fuel plate irradiated in the FUTURE test in the BR2 reactor was performed with the Dispersion Analysis Research Tool (DART), a dispersion fuel performance code. DART is equipped with an interaction or interdiffusion layer (IL) growth correlation formulated to describe the temperature dependence of ion mixing results. The agreement between calculated and measured fuel meat constituent volume fractions and swelling data demonstrated that the temperature effect on in-pile Al-UMo interdiffusion is well captured with the correlation. In this case, the fitted activation energy is 0.70 eV. Considering the uncertainties associated with the ion irradiation data, the activation energy obtained from in-pile data fitting is in accord with that from ion irradiation results.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Leveraging Polymorphism in YbCuBi to Map Transport and Elastic Properties

AMX Zintl compounds with the hexagonal ZrBeSi structure have gained significant attention for their remarkable vacancy tolerance and low thermal conductivity. Their 2D honeycomb sublattice, composed of M–X covalent bonds, is believed to contribute to high anharmonicity and unusual thermal transport properties. In this study, we explore the temperature-dependent polymorphism of YbCuBi as a model system to investigate the relationship between the structure and elastic and thermal transport properties in AMX Zintls. YbCuBi undergoes a structural transition from the “flat” Cu–Bi layers in the ZrBeSi structure to corrugated layers in the LiGaGe structure below 410 K, resulting in a distortion of its centrosymmetric structure. To probe the effects of this crystallographic transition, we employ inelastic neutron scattering and temperature-dependent resonant ultrasound spectroscopy. These experimental findings, coupled with first-principles calculations and thermal conductivity measurements, allow us to elucidate a direct relationship between corrugation of the honeycomb lattice and the observed changes in elastic and thermal transport properties. These insights can be extended to other Zintl phases with similar structure types, providing a platform for the rational design of functional materials with tailored thermal properties.

Chemical structure↗
DOE OSTI2023

Development of coal-derived carbon-based structural unit as a potential new building material

Coal combustion for energy has not only wasted the hydrogen-rich volatile matters but also results in CO 2 emission causing serious environmental issues. An integrated coal pyrolysis and solvent extraction process under elevated temperatures in an inert atmosphere is implemented to convert as-mined coal from Wyoming Powder River Basin to functional carbon elements such as pyrolysis char (PC). This paper presents the development and fabrication of new carbon-based structural unit (CSU) using pulverized PC and two coal-derived pitches (mesophase pitch and tar pitch) to attain high compressive strength greater than 30 MPa, low thermal conductivity less than 0.30 W/m.K, and low density less than 1.25 g/cm 3 . CSUs have the potential to overcome the current challenges with cement and concrete through pressurized fabrication followed by carbonization. This study aims to develop CSU with nearly 100% coal-derived carbon material for structural application in buildings. The effects of pressing pressures, carbonization temperatures, and binder contents on the density and mechanical and thermal properties of CSU samples are investigated. The study concludes that mesophase pitch produces a better performance of CSU samples, a combination of 100 MPa pressing pressure and carbonization temperature of 900 ⁰C yields the highest compressive strength, and a 25% MP content is recommended for low-cost CSU fabrication. Furthermoer, CSU has a much lower density, lower thermal conductivity, higher compressive strength, and higher strength-to-density ratio than normal concrete.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural and Oxidation Effects of Nb Additions to U3Si2

U3Si2 is a long term, accident-tolerant nuclear fuel candidate for light-water reactors because of its superior thermal conductivity and increased uranium density when compared to traditional uranium dioxide (UO2). While reducing internal thermal stresses and increasing efficiency, U3Si2 exhibits energetic oxidation during certain off-normal and accident scenarios, which include coolant or steam exposure. To mitigate this, Nb is investigated as an alloy constituent to enhance corrosion resistance and increase mechanical strength. The work presented investigates the response of Nb-alloyed U3Si2 to steam atmospheres. A thermogravimetric analysis is conducted in flowing steam to T > 1000 °C to assess oxidation resistance. The phase characterization of as-melted, thermally annealed and post-oxidation compositions with up to 12 vol% Nb by powder X-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy is reported.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Elucidating the effect of preheating temperature on melt pool morphology variation in Inconel 718 laser powder bed fusion via simulation and experiment

In laser powder bed fusion (L-PBF) additive manufacturing, the mechanical performance, microstructure and defects of fabricated parts are closely associated with the melt pool morphology, e.g., its dimension and shape through the building process. Past studies have largely focused on how the process parameters such as laser power and scan speed affect melt pool characteristics. In this study, the melt pool morphology variation as a function of preheating temperature in the conduction, transition, and keyhole regimes and the underlying mechanisms in each regime are investigated through ex-situ sample characterization and computation thermal fluid dynamics (CtFD) simulation. Single tracks with different combinations of laser power and scan speed are deposited on an Inconel 718 bare plate preheated to a temperature range of 100–500 °C in the experiment. Significant changes are observed in melt pool morphology as a function of preheating temperature from optical measurements of melt track cross sections. The depth of melt pool in the three regimes increases monotonically with preheating temperature, e.g., at 500 °C, the experimental melt pool depth is increased by 49% in conduction regime, 34% in transition regime and 33% in keyhole regime, respectively, while the variation of melt pool width in each regime does not all follow an increasing trend but depends on the melt pool regimes. Melt pool width variation in the conduction and transition regimes is found to depend on the enhanced heat conduction directly related to temperature dependent thermal properties. Through validated CtFD simulations, it is found that in the keyhole regime the evaporation mass, recoil pressure, and laser drilling effect is enhanced with higher preheating temperature, which gives rise to a deeper melt pool. The simulations also reveal that preheating temperature significantly elongates the melt track length due to the increased flow rate and strong recoil pressure that accelerates the backward flow.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Phase Behavior and Ionic Conductivity of Blended, Ion-Condensed Electrolytes with Ordered Morphologies

In this study, the amphiphilic salt lithium trifluoromethanesulfonylimide octadecane (C18LiTFSI) was used as a basis to investigate the effects of anion density and cation coordination sites within blended electrolytes with strong ionic aggregation. C18LiTFSI was previously reported as a single-component, ion-condensed electrolyte with a wide layered liquid crystalline phase regime. Three additive molecules with varyingly sized polar sulfonyl groups attached to an octodecane-tail were synthesized and mixed with C18LiTFSI. The thermal properties, morphology, and ionic conductivity of the blended electrolytes were characterized. It was found that the blended electrolytes exhibited layered liquid crystalline morphology over a narrower temperature range than the pure salt, and the ionic conductivity of the blended liquid crystalline electrolytes were generally lower than that of the pure salt. Surprising, the additives were found to have the greatest effect on the bulk ionic conductivity of the semicrystalline phase of the electrolytes. Addition of minor fractions of methylsulfonyloctadecane to C18LiTFSI resulted in increases in conductivity of over two orders of magnitude at room temperature, while addition of ethylsulfonyloctadecane or isopropylsulfonyloctadecane with the larger head group resulted in decreased ionic conductivity over the entire composition space and temperature range investigated.

Collins, Hannah (ORCID:0000000338858136)↗
DOE OSTI2024

Electrical conductivity of a warm neutron star crust in magnetic fields: Neutron-drip regime

We compute the anisotropic electrical conductivity tensor of the inner crust of a compact star at nonzero temperature by extending a previous work on the conductivity of the outer crust. The physical scenarios, where such crust is formed, involve protoneutron stars born in supernova explosions, binary neutron star mergers, and accreting neutron stars. The temperature-density range studied covers the transition from a semidegenerate to a highly degenerate electron gas and assumes that the nuclei form a liquid, i.e., the temperature is above the melting temperature of the lattice of nuclei. The electronic transition probabilities include (i) the screening of electron-ion interaction in the hard-thermal-loop approximation for the QED plasma, (ii) the correlations of the ionic component in a one-component plasma, and (iii) finite nuclear size effects. The conductivity tensor is obtained from the Boltzmann kinetic equation in relaxation time approximation accounting for the anisotropy introduced by a magnetic field. The sensitivity of the results towards the matter composition of the inner crust is explored by using several compositions of the inner crust, which were obtained using different nuclear interactions and methods of solving the many-body problem. The standard deviations of relaxation time and components of the conductivity tensor from the average are below ≤25% except close to crust-core transition, where nonspherical nuclear structures are expected. Finally, our results can be used in dissipative magnetohydrodynamics simulations of warm compact stars.

Physics↗
DOE OSTI2023

Thermal hydraulic characteristics of liquid sodium and supercritical CO 2 in a diffusion bonded heat exchanger

Compact heat exchangers are being examined for use in advanced, high-temperature nuclear or concentrated solar power plants to improve thermal efficiencies and reduce capital costs. At the time of this work, no experimental investigation of liquid sodium in the popular diffusion-bonded heat exchanger design had been performed. Herein this paper describes the thermal-hydraulic and overall operations performance observed during testing of a 316/L stainless steel “zig-zag” microchannel heat exchanger operating between a (0.5 kg/s) sodium loop and a (0.3 kg/s) recuperated supercritical CO 2 system with outlet conditions up to 550 °C at 16 MPa. Observed pressure drop is presented in the form of an effective friction factor correlation which aligns closely with recent experimental data. The thermal performance of this heat exchanger, measured by its overall conductance under various flow conditions, was decomposed to examine the independent convection behaviors of both the CO 2 and sodium streams. These results are presented in the form of Nusselt correlations fitted to the experimental data. The sodium heat transfer correlation aligns closely with the widely accepted Lubarsky-Kaufman correlation, while the CO 2 heat transfer correlation lies between previous correlations developed by computational and experimental methods. This was the first long-duration use of sodium in a microchannels (~1.8 mm hydraulic diameter) heat exchanger. The use of an oxide control system enabled trouble-free operation of the heat exchanger for over 150 h of high-temperature operation. This first-of-a-kind demonstration using liquid sodium and supercritical carbon dioxide shows great promise for further application of this technology in advanced nuclear or solar power plants.

42 ENGINEERING↗
DOE OSTI2024

A high-throughput framework for lattice dynamics

We develop an automated high-throughput workflow for calculating lattice dynamical properties from first principles including those dictated by anharmonicity. The pipeline automatically computes interatomic force constants (IFCs) up to 4th order from perturbed training supercells, and uses the IFCs to calculate lattice thermal conductivity, coefficient of thermal expansion, and vibrational free energy and entropy. It performs phonon renormalization for dynamically unstable compounds to obtain real effective phonon spectra at finite temperatures and calculates the associated free energy corrections. The methods and parameters are chosen to balance computational efficiency and result accuracy, assessed through convergence testing and comparisons with experimental measurements. Deployment of this workflow at a large scale would facilitate materials discovery efforts toward functionalities including thermoelectrics, contact materials, ferroelectrics, aerospace components, as well as general phase diagram construction.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Giant spin Seebeck effect through an interface organic semiconductor

Interfacing an organic semiconductor C 60 with a non-magnetic metallic thin film (Cu or Pt) has created a novel heterostructure that is ferromagnetic at ambient temperature, while its interface with a magnetic metal (Fe or Co) can tune the anisotropic magnetic surface property of the material. Here, we demonstrate that sandwiching C60 in between a magnetic insulator (Y 3 Fe 5 O 12 :YIG) and a non-magnetic, strong spin–orbit metal (Pt) promotes highly efficient spin current transport via the thermally driven spin Seebeck effect (SSE). Experiments and first principles calculations consistently show that the presence of C 60 reduces significantly the conductivity mismatch between YIG and Pt and the surface perpendicular magnetic anisotropy of YIG, giving rise to enhanced spin mixing conductance across YIG/C 60 /Pt interfaces. As a result, a 600% increase in the SSE voltage (V LSSE ) has been realized in YIG/C 60 /Pt relative to YIG/Pt. Temperature-dependent SSE voltage measurements on YIG/C 60 /Pt with varying C 60 layer thicknesses also show an exponential increase in V LSSE at low temperatures below 200 K, resembling the temperature evolution of spin diffusion length of C 60 . Our report emphasizes the important roles of the magnetic anisotropy and the spin diffusion length of the intermediate layer in the SSE in YIG/C 60 /Pt structures, providing a new pathway for developing novel spin-caloric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Universal time-dependent Ginzburg-Landau theory

We study the hydrodynamics of superconductors within the framework of Schwinger-Keldysh effective field theory (EFT). We show that in the vicinity of the superconducting phase transition the most general leading-order EFT satisfying the local Kubo-Martin-Schwinger condition is described by a version of the time-dependent Ginzburg-Landau (TDGL) equations augmented with stochastic terms. This version of TDGL is applicable in the gapless regime independent of any microscopic details. Within this approach, it is possible to include systematically the effects of nonuniform temperature and heat conductivity, as well as explicit or spontaneous breaking of time reversal. Here, we also introduce a thermal version of the Josephson relation and use it to construct an exotic hydrodynamics describing a phase of matter where heat can flow without dissipation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Determining processing behaviour of pure Cu in laser powder bed fusion using direct micro-calorimetry

We report copper is challenging to process by laser powder bed fusion (LPBF) given its high reflectivity at common infrared laser diode wavelengths and high thermal conductivity. Successful deposition of copper in a predictable and repeatable fashion relies on understanding the development of the keyhole melting regime, as well as heating, melting, boiling and vapour formation behaviour when interacting with a laser beam within an LPBF environment. In this study, in situ optical absorptivity measurements are used to clarify the complex physics of the laser material interaction. Absorptivity of laser energy is measured using direct micro-calorimetry and compared to melt pool depth in correlation to processing parameters. The measured absorptivity for a 100 μm layer thickness of powder was found to be approximately four times higher than that of the bare polished discs. It was also shown that high laser power above 500 W and scan speed up to 150 mm/s are appropriate for effective melting of the powder layer, with these parameters overcoming the threshold required to achieve keyhole melting. This is explained by multiple reflections withing the powder particles and the lower thermal conductivity of packed powder in comparison to bare discs. Melt pool formation was found to be highly unstable and an explosive behavior was observed when in the keyhole regime, caused by high fluctuations in absorptivity values. This work demonstrates calorimetry can be used to monitor melting behaviour in a real-time fashion during processing for this challenging to process material, thereby avoiding unnecessary parametric optimisation. In addition, the parametric window for optimum processing revealed here can inform future work.

36 MATERIALS SCIENCE↗