Search NASA⌕ Search

SEARCH · Search NASA

Results for “Engineering - Particle accelerators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

EDIN design study alternate space shuttle booster replacement concepts. Volume 1: Engineering analysis

The use of a recoverable liquid rocket booster (LRB) system to replace the existing solid rocket booster (SRB) system for the shuttle was studied. Historical weight estimating relationships were developed for the LRB using Saturn technology and modified as required. Mission performance was computed using February 1975 shuttle configuration groundrules to allow reasonable comparison of the existing shuttle with the study designs. The launch trajectory was constrained to pass through both the RTLS/AOA and main engine cut off points of the shuttle reference mission 1. Performance analysis is based on a point design trajectory model which optimizes initial tilt rate and exoatmospheric pitch profile. A gravity turn was employed during the boost phase in place of the shuttle angle of attack profile. Engine throttling add/or shutdown was used to constrain dynamic pressure and/or longitudinal acceleration where necessary. Four basic configurations were investigated: a parallel burn vehicle with an F-1 engine powered LRB; a parallel burn vehicle with a high pressure engine powered LRB; a series burn vehicle with a high pressure engine powered LRB. The relative sizes of the LRB and the ET are optimized to minimize GLOW in most cases.

Demakes, P. T.↗
NASA NTRS1953

Altitude Operational Characteristics of Prototype J40-WE-8 Turbojet Engine

The altitude operational characteristics of the prototype J40-WE-8 turbojet engine were determined in the NACA Lewis altitude wind tunnel. The operational characteristics that were obtained include (1) compressor surge characteristics, (2) acceleration and deceleration rates, (3) steady-state windmilling-engine characteristics, (4) altitude ignition characteristics, and (5) the effect of two grades of fuel on steady-state engine performance at an altitude of 45,000 feet and a flight Mach number of 0.20. The altitude ignition characteristics determined include the effects of (1) ignition fuel flow, (2) two ignition procedures, (3) fuel temperatures, and (4) two grades of fuel on ignition characteristics. The compressor surge line, when presented as a function of compressor pressure ratio and corrected engine speed, was not affected by changes in flight condition and was independent of engine-inlet installation and of the manner in which surge was approached, rapidly or slowly. Also there was no effect of altitude or engine-inlet installation on the compressor surge recovery line when presented as a function of compressor pressure ratio and corrected engine speed.

FUELS - RELATION TO ENGINE PERFORMANCE↗
NASA NTRS2013

Model-Based Control of a Nonlinear Aircraft Engine Simulation using an Optimal Tuner Kalman Filter Approach

This paper covers the development of a model-based engine control (MBEC) methodology featuring a self tuning on-board model applied to an aircraft turbofan engine simulation. Here, the Commercial Modular Aero-Propulsion System Simulation 40,000 (CMAPSS40k) serves as the MBEC application engine. CMAPSS40k is capable of modeling realistic engine performance, allowing for a verification of the MBEC over a wide range of operating points. The on-board model is a piece-wise linear model derived from CMAPSS40k and updated using an optimal tuner Kalman Filter (OTKF) estimation routine, which enables the on-board model to self-tune to account for engine performance variations. The focus here is on developing a methodology for MBEC with direct control of estimated parameters of interest such as thrust and stall margins. Investigations using the MBEC to provide a stall margin limit for the controller protection logic are presented that could provide benefits over a simple acceleration schedule that is currently used in traditional engine control architectures.

Control Theory↗
DOE OSTI2023

A review of neutronics and thermal hydraulics–based screening methods applied to accelerated nuclear fuel qualification

This paper reviews the state-of-the-art engineering approach for using thermal hydraulic (TH) and neutronics modeling and simulation (M&S) tools to perform rapid screening studies of novel nuclear fuel concepts within the context of accelerated fuel qualification. Global research efforts have introduced nuclear fuel and material concepts that mark a significant departure from traditional reactor materials. The number of new technologies being considered for development for light water reactors and advanced reactor types has created the need for an accelerated fuel qualification procedure. A key component of this procedure is the rapid identification of the most promising fuel concepts using computational screening studies. Advanced TH and neutronic M&S tools should be leveraged to efficiently determine whether the reactor performance and safety characteristics of a given concept warrant additional studies or whether the concept requires modification or elimination. This paper reviews best practices for performing these TH and neutronics screening studies at various stages during a fuel concept's progression through the qualification procedure. The motivation behind standardizing this approach is to minimize time and resources spent on qualification activities for fuel concepts that could be quickly refined or eliminated from consideration based on their reactor physics and TH characteristics. Adoption of this screening procedure—which focuses primarily on nuclear fuels but may be applicable to other reactor materials—will also help accelerate new material qualification by generating boundary conditions crucial to fuel performance evaluations and highlighting needed areas of separate effects experimentation. This article reviews the motivation behind the introduction of novel nuclear fuel concepts, provides incentive for utilizing TH- and neutronics-based screening studies, describes the screening approach and methodology, and includes discussion on how to interpret screening results to provide recommendations for the continued development of a given concept.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1986

Radioactivities in returned lunar materials and in meteorites

A preliminary C-14 study on lunar soil was carried out with the University of Toronto Iso Trace accelerator mass spectrometer. This accelerator was recommended for C-14 work by Dr. R. Schneider of A.S. and E., who was the field engineer during the assemblage and start-up operation of the accelerator. After the preliminary study using CO2 from 10084,937 soil, which had previously been counted with low-level mini-proportional counters, it became clear that the Toronto accelerator could carry out C-14/C-13/C-12 ratio measurements on 1 gram meteorite and lunar samples and that the C-14 measurements are done with higher precision and better reliability than elsewhere. A collaborative program with the University of Toronto Iso Trace accelerator group, which is expected to be scientifically fruitful. Arrangements have been made for Dr. R.P. Beukens of the Toronto Accelerator Group to extract the carbon compounds from Antarctic meteorite and lunar samples and to convert the compounds to CO2. During the past two years, a uranium-series dating method was developed for polar ice, which method is being applied to ice from the Allan Hills site, Byrd core, and the Beardsmore glacier.

Fireman, E. L.↗
NASA NTRS1992

Design tradeoffs on engine-integrated hypersonic vehicles

Two classes of airbreathing hypersonic vehicle concepts, one for primarily cruise missions and the other for accelerator type missions, are presented. Both are designed with waverider airframes and hydrogen-fueled scramjet engine modules. Cruise configurations are optimized for the product of I(sp) and L/D while matching lift to weight and thrust to drag at some equivalence ratio. Accelerator configurations are optimized for effective specific impulse while matching lift to weight at an equivalence ratio of one. The method and computer code developed to optimize the configurations are discussed. The features and design tradeoffs for each class of vehicles are described. Recently available weight estimates for all-body waveriders have had a significant impact on the integrated configurations. Mach 8 vehicles at 40 km altitude optimized with the cruise objective function have L/Ds of 2.55 to 2.92 and I(sp)s of 2850 to 2940 sec. A Mach 14 vehicle at 40-km altitude optimized with the accelerator objective function has an I(sp) sub eff of 189 sec, and a Mach 10 vehicle an I(sp) sub eff of 880 sec.

O'Neill, Mary Kae L.↗
NASA NTRS1989

Electrostatic Plasma Accelerator (EPA)

The Electrostatic Plasma Accelerator (EPA) is a thruster concept which promises specific impulse levels between low power arcjets and those of the ion engine while retaining the relative simplicity of the arcjet. The EPA thruster produces thrust through the electrostatic acceleration of a moderately dense plasma. No accelerating electrodes are used and the specific impulse is a direct function of the applied discharge voltage and the propellant atomic mass. The goal of the present program is to demonstrate feasibility of the EPA thruster concept through experimental and theoretical investigations of the EPA acceleration mechanism and discharge chamber performance. Experimental investigations will include operating the test bed ion (TBI) engine as an EPA thruster and parametrically varying the thruster geometry and operating conditions to quantify the electrostatic plasma acceleration effect. The theoretical investigations will include the development of a discharge chamber model which describes the relationships between the engine size, plasma properties, and overall performance. For the EPA thruster to be a viable propulsion concept, overall thruster efficiencies approaching 30% with specific impulses approaching 1000 s must be achieved.

Brophy, John R.↗
DOE OSTI2022

Concept of Operations of Next-Generation Traffic Control Utilizing Infrastructure-Based Cooperative Perception

This paper provides a system architecture for an infrastructure-based cooperative perception fusion engine for next-generation traffic control. This engine will provide a complete state-space digital representation with measurable accuracy to support a wide-range of applications. The architecture includes inputs, functional flow, data standardization recommendations, outputs, and supported applications. The cooperative perception engine addresses critical needs with respect to accelerating the benefits of automation through intelligent roadway infrastructure, which complements and accelerates connected and automated vehicle (CAV) technology. The cooperative perception acquires and fuses information from sensors (radar, LiDAR, and cameras) and CAVs to perceive roadway traffic states of moving objects, creates a complete 3D digital representation of that state-space, and communicates it to downstream application such as intelligent signal control, safety and energy applications, and cooperate driving applications. The intelligent roadway infrastructure approach, as opposed to a vehicle-centric approach, is more scalable because it can be deployed to the roughly 300,000 signalized intersections more readily than over 300 million vehicles in the United States, and accrues early-stage benefits equitable to all roadway users addressing safety, equity, fuel efficiency, and greenhouse gas reduction.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

A New Design Consideration for Bidirectional Resonant Converters

This paper introduces innovative design considerations for a bidirectional resonant converter, optimized for Electric Vehicle (EV) charging and vehicle-togrid (V2G) applications. By eliminating the need for complex voltage or current gain functions, the proposed design greatly simplifies the development process, making it more accessible for manufacturers and system integrators. This approach not only reduces engineering time and resource investment but also accelerates time-to-market, giving stakeholders a competitive edge in rapidly expanding EV infrastructure markets. In addition, the streamlined design ensures soft switching at maximum output power, leading to higher efficiency and improved durability, which translates to lower operating costs and a longer service life for EV charging equipment. These benefits provide a clear pathway to more cost-effective, scalable, and sustainable EV charging and V2G solutions, enhancing value for stakeholders by facilitating smoother integration into the grid and supporting energy resilience. To validate the benefits, a 60 kW bidirectional charger with a flexible input range of 700−900VDC and an output range of 400−1250VDC was developed, underscoring the design's adaptability and potential for large-scale implementation.

Asa, Erdem [ORNL] (ORCID:0000000190884812)↗
DOE OSTI2018

Construction of an Object-Oriented Interface to an Enhanced EGS Monte Carlo Code

The version of SLAC’s EGS Code System (known as EGS4) was clearly recognized throughout the world as a “gold standard” for solving physics and engineering problems related to the transport of electrons and photons in any element, compound, or mixture. However, EGS4 was written in a computer language called Mortran3 and the learning curve for this rather obscure language was difficult and steep. One major objective of this project was to convert the EGS4 Mortran3 coding into Fortran77, making it much simpler for first-time users to understand and appreciate. In addition, since the introduction of EGS4 in 1985, a number of enhancements in electron-photon transport, as well as a growing need for additional physics processes, had been developed, and the new code (called EGS5) would incorporate more than 20 of these improvements. Of course, many key benchmark simulations had to be made during its development in order to prove that EGS5 was just as credible as its predecessor, EGS4. All of the above was tasked to SLAC, with outside support coming from colleagues at the University of Michigan (Nuclear Engineering Department) and at the High Energy Accelerator Research Organization (KEK) in Japan.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2026

Automation of Laser Plasma Focused Ion Beam Microscopy for Next-Gen Energy Materials

Automation can revolutionize the use of ultrafast laser ablation and plasma-focused ion beam (PFIB) techniques for high-throughput, reproducible cross-sectioning and various sample preparation in materials characterization. As these methods become essential for analyzing complex energy materials and next-generation devices, efficient, standardized workflows are needed to minimize variability and enhance precision. This work highlights our advancements in developing automated processes for sample preparation that integrates machine learning, workflow optimization, and large-scale data acquisition to improve efficiency and scalability in applications such as electrolyzers, photovoltaic cells, and microelectronics. To streamline cross-sectioning and lamella fabrication, we have implemented fully automated workflows that standardize laser ablation and PFIB milling sequences. These workflows incorporate pre-programmed protocols for material removal, alignment, and thinning, reducing user intervention and ensuring consistency across different sample types. Machine learning algorithms further enhance automation by predicting optimal milling strategies and adapting parameters based on material properties and sectioning requirements. This approach significantly improves throughput while maintaining the structural integrity of prepared samples for high-resolution imaging and analysis, including transmission electron microscopy. Beyond sample preparation, our automation platform enables the acquisition of large, high-resolution datasets through serial sectioning, image alignment, and 3D reconstruction. These automated routines facilitate multi-scale characterization, capturing structural and compositional details from the nanoscale to the device level. By reducing variability and increasing efficiency, our automated approach enhances defect analysis, failure diagnostics, and process optimization, accelerating advancements in materials research and device engineering.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Limit Cycle Oscillating Detonation Wave Behavior Analysis Within a Rotating Detonation Engine

Limit cycle oscillation (LCO) detonation wave behaviors are presented and analyzed for test times exceeding 20 s in a water-cooled rotating detonation engine (RDE). LCO detonation waves exhibit cyclic acceleration and deceleration, resulting in oscillating wave spacing at unique process conditions. In previous RDE studies, similar behaviors have been studied as microsecond-scale instabilities leading to ascending or descending modal transitions. In the current work, however, LCO waves are considered a persistent wave mode, occupying unique portions of the operational envelope adjacent to those of their equally spaced counterparts. These occurrences of LCO waves are repeatable, enduring behaviors. A method to generate shifted contour surfaces specifically intended to extract and analyze wave spacing variation through time, termed limit cycle oscillation visualization (LCOV) surfaces, is presented. LCOV surfaces transform data into the reference frame of a primary traveling wave and are used to analyze quasi-steady, short-timescale, and transitional LCO modes. Results are leveraged to understand the relationship between fill height, wave strength, local wave acceleration, and subsequent LCO wave spacing for individual wave sets. In conclusion, quasi-steady LCO waves display wave spacing oscillations between equal spacing values associated with ±1 wave across runs exceeding 18 s.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1985

Orbit on demand - Will cost determine best design?

Eleven design concepts for vertical (V) and horizontal (H) take-off launch-on-demand manned orbital vehicles are discussed. Attention is given to up to three stages, Mach numbers (sub-, 2, or 3), expendable boosters, drop tanks (DT), and storable (S) or cryogenic fuels. All the concepts feature lifting bodies with circular cross-section and most have a 7 ft diam, 15 ft long payload bay as well as a crew compartment. Expendable elements impose higher costs and in some cases reduce all-azimuth launch capabilities. Single-stage vehicles simplify the logistics whether in H or V configuration. A two-stage H vehicle offers launch offset for the desired orbital plane before firing the rocket engines after take-off and subsonic acceleration. A two-stage fully reusable V form has the second lowest weight of the vehicles studied and an all-azimuth launch capability. Better definition of the prospective mission requirements is needed before choosing among the alternatives.

Macconochie, J. O.↗
NASA NTRS1990

Cryogenic liquid hydrogen reorientation activated by constant reverse gravity acceleration of geyser initiation

A key objective for cryogenic fluid management in a spacecraft propulsion system is development of the technology necessary for acquisition or positioning of liquid outflow or vapor venting. Numerical simulation of positive liquid acquisition is attempted by introducing a reverse gravity acceleration from the propulsive thrust of auxiliary engines which exceeds critical value for the initiation of a geyser. Based on the computer simulation of flow fields during the course of fluid reorientation, six dimensionless parameters resulted. These parameters hold near-constant values through the entire range of liquid filled levels, from 30 to 80 percent, during the course of fluid reorientation.

Hung, R. J.↗
NASA NTRS1993

Engine/airframe integration for waverider cruise vehicles

Engine-airframe integrated hypersonic waveriders have been optimized previously for both cruising flight and accelerators using inverse design flowfields to provide desirable aerodynamic performance and inlet properties. With engine installation, cruisers retain the high L/D advantages of the basic waverider form. To provide an understanding of waverider optimizer trends, an analytical development is presented which includes the presentation of a simplified model of a generic waverider shape. The model is shown to have good agreement with computational results, and it is used to demonstrate engineering tradeoffs in L/D, volume, and volume efficiency. Based on the demonstrated performance trends, and considering the desirability of uniform inlet flow, an improved waverider shape for engine-airframe integration is proposed using a hybrid cone-wedge generating flowfield.

Lewis, Mark J.↗