Search NASA⌕ Search

SEARCH · Search NASA

Results for “FRICTION FACTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Gasdynamics of the cryogenic cooler of the Nimbus F spacecraft

This paper presents a theoretical study of the gasdynamic behavior of the system used to vent methane gas from an open-cycle cryogenic cooler carried on the Nimbus F satellite. The flow of this gas from the cryogen tank to the vent-line exit takes place at very low Reynolds number, and is strongly affected by variations in the tube cross-sectional area, substantial heat addition, and important frictional effects. All three of these factors play a role in determining the choking mass flow. Finite-difference calculations are used to establish the mass flow rates for a range of cryogen temperatures. Finite-difference calculations are also used to determine the flowfield in the plume that results when the vented gas exits from the spacecraft. The momentum-flux distributions within the plume are then used to estimate the torques applied to the spacecraft when the plume impinges on several surfaces near the exit point. These torque estimates compare favorably with flight data.

Rae, W. J.↗

Atmospheric model development in support of SEASAT. Volume 4: Forecast model sensitivity study

Atmospheric analysis and prediction models of varying (grid) resolution were developed. The models were tested using real observational data for the purpose of assessing the impact of grid resolution on short range numerical weather prediction. The work statement was amended to include the performance of sensitivity tests using a coarse mesh (63 x 63 x 5 level) prediction model in order to identify and order factors which might mask or impair the utility of SEASAT data on short range weather prediction. Such factors included: initial conditions; topography; surface friction; latent heating; diffusion of momentum and temperature; and computational devices such as tendency truncators, pressure smoothers, and temporal filters.

Lewit, H. L.↗

History of ball bearings

The familiar precision rolling-element bearings of the twentieth century are products of exacting technology and sophisticated science. Their very effectiveness and basic simplicity of form may discourage further interest in their history and development. Yet the full story covers a large portion of recorded history and surprising evidence of an early recognition of the advantages of rolling motion over sliding action and progress toward the development of rolling-element bearings. The development of rolling-element bearings is followed from the earliest civilizations to the end of the eighteenth century. The influence of general technological developments, particularly those concerned with the movement of large building blocks, road transportation, instruments, water-raising equipment, and windmills are discussed, together with the emergence of studies of the nature of rolling friction and the impact of economic factors. By 1800 the essential features of ball and rolling-element bearings had emerged and it only remained for precision manufacture and mass production to confirm the value of these fascinating machine elements.

Dowson, D.↗

Modeling fatigue crack growth in cross ply titanium matrix composites

In this study, the fatigue crack growth behavior of fiber bridging matrix cracks in cross-ply SCS-6/Ti-15-3 and SCS-6/Timetal-21S laminates containing center holes was investigated. Experimental observations revealed that matrix cracking was far more extensive and wide spread in the SCS-6/Ti-15-3 laminates compared to that in the SCS-6/Timetal-21S laminates. In addition, the fatigue life of the SCS-6/Ti-15-3 laminates was significantly longer than that of the SCS-6/Timetal-21S laminates. The matrix cracking observed in both material systems was analyzed using a fiber bridging (FB) model which was formulated using the boundary correction factors and weight functions for center hole specimen configurations. A frictional shear stress is assumed in the FB model and was used as a curve fitting parameter to model matrix crack growth data. The higher frictional shear stresses calculated in the SCS-6/Timetal-21S laminates resulted in lower stress intensity factors in the matrix and higher axial stresses in the fibers compared to those in the SCS-6/Ti-15-3 laminates at the same applied stress levels.

Bakuckas, J. G., Jr.↗

Optimum subsonic, high-angle-of-attack nacelles

Many proposed advanced aircraft - but especially tilt-nacelle, subsonic-cruise, V/STOL aircraft - require nacelles that operate over a wide range of aerodynamic conditions. The optimum design of such nacelles and their inlets is described, including how the inlet low-speed design conditions are selected, the conditions for which the various regions of the inlet are designed, and appropriate criteria of merit. For low-speed operation the optimum internal surface velocity distributions and skin friction distributions are described for three categories of inlets: those without boundary-layer control (BLC), those with BLC, and those with blow-in door slots and retractable slats. Experimental results are presented that show the performance of the various types of inlets. At cruise speed the effect of factors that reduce the nacelle external surface area and the local skin friction is illustrated. These factors are cruise Mach number, inlet throat size, fan-face Mach number, and nacelle contour. The interrelation of these cruise-speed factors with the design requirements for good low-speed performance is discussed. Finally an inlet design without BLC and an optimized inlet design with slots and slats are compared to illustrate the possible reductions in nacelle size.

Luidens, R. W.↗

An Experimental and Numerical Analysis of the Compression of Bimetallic Cylinders

This paper investigates the upsetting of bimetallic cylinders with an aluminum alloy center and a brass ring. The influence of the center-ring shape factor and type of assembly fit (interference and clearance), and the effect of friction on the compression force and ductile damage are comprehensively analyzed by means of a combined numerical-experimental approach. Results showed that the higher the shape factor, the lower the forces required, whereas the effect of friction is especially important for cylinders with the lowest shape factors. The type of assembly fit does not influence the compression force. The accumulated ductile damage in the compression of bimetallic cylinders is higher than in single-material cylinders, and the higher the shape factor, the lower the damage for the same amount of stroke. The highest values of damaged were found to occur at the middle plane, and typically in the ring. Results also showed that an interference fit was more favorable for preventing fracture of the ring than a clearance fit. Microstructural analysis by scanning electron microscopy revealed a good agreement with the finite element predicted distribution of ductile damage.

36 MATERIALS SCIENCE↗

Saltation threshold on Mars - The effect of interparticle force, surface roughness, and low atmospheric density

Results are reported for wind-tunnel experiments performed to determine the threshold friction speed of particles with different densities. Experimentally determined threshold speeds are plotted as a function of particle diameter and in terms of threshold parameter vs particle friction Reynolds number. The curves are compared with those of previous experiments, and an A-B curve is plotted to show differences in threshold speed due to differences in size distributions and particle shapes. Effects of particle diameter are investigated, an expression for threshold speed is derived by considering the equilibrium forces acting on a single particle, and other approximately valid expressions are evaluated. It is shown that the assumption of universality of the A-B curve is in error at very low pressures for small particles and that only predictions which take account of both Reynolds number and effects of interparticle forces yield reasonable agreement with experimental data. Effects of nonerodible surface roughness are examined, and threshold speeds computed with allowance for this factor are compared with experimental values. Threshold friction speeds on Mars are then estimated for a surface pressure of 5 mbar, taking into account all the factors considered.

Iversen, J. D.↗

A numerical investigation of severe thunderstorm gust fronts

A numerical model was developed to simulate the evolution and structure of severe thunderstorm gust fronts. The model is a non-hydrostatic, fine resolution, cross-sectional primitive equation model. Two-dimensional horizontal and vertical equations of motion, the continuity equation, and the thermodynamic energy equation were utilized. It was shown that two dominant factors influencing gust front configuration are surface friction and the solenoidal field coincident with the front. It is suggested that solenoidal accelerations oppose the deceleration of surface friction. After a downdraft is initiated in the model, these opposing tendencies soon reach a balance and the gust front achieves a quasi-steady configuration. Thus, the experiments indicate that surface friction does not induce a cycle of front formation and collapse. In addition, the effect of evaporative cooling in producing a vigorous downdraft was parameterized by a local cooling function. Greater cooling in the downdraft results in a more intense gust front that exhibits stronger wind maximums and greater shears. The ambient air stability was shown to be an important factor influencing the depth of the cold outflow.

Mitchell, K. E.↗

Development of a New Method to Investigate Dynamic Friction Behavior of Metallic Materials Using a Kolsky Tension Bar

Understanding the interfacial behavior of two materials sliding relative to each other is import ant in computational modeling and simulating impact or shock response of components, subsystems, and even full-scale systems. Although often considered as a constant for different applications, the coefficient of friction may be dependent on a number of factors such as normal force, roughness, material type, temperature, and sliding velocity. In this study, a new method based on a Kolsky tension bar with a custom-made friction fixture was developed for measurement of the dynamic friction coefficient between two metallic materials at high sliding velocities. In this new method, polyvinylidene fluoride (PVDF) thin film force sensors were used to measure the normal force, while a strain gage on the transmission bar was used to measure the friction force. As such, the dynamic friction coefficient is calculated with the normal and friction forces. The impact velocity can be varied to investigate the dependency of friction coefficient on impact velocity. To evaluate the technique, friction coefficients between 4340 steel and 7075-T6 we re measured at three different sliding velocities of 4, 8 and 11 m/s. Effects of surface roughness, normal force, and impact speed were also explored . Decreased static and kinetic friction coefficient s were observed when the normal force was increased at constant sliding velocity. With increasing velocity, the friction coefficient remained fairly constant for the three velocities studied. Higher friction coefficients were measured when the specimen roughness was increased.

36 MATERIALS SCIENCE↗

Extended ion pumped vacuum friction test

Boundary layer friction data under ion pumped vacuum was taken for sixteen material couples. The test series was an extension of a previous study of the effects of modified ion pumped environments. Sliding distances imposed in the present effort greatly exceeded any studied in the previous contiguous, flight or ground tests. Wear out of specific couples, in particular, thin film lubricants was noted. The behavior of the test hardware including wear out of the mechanisms was noted. As a result, the impact of test interruption was observed for several test couples. Recovery of the friction upon re-establishing sliding in vacuum was generally rapid. The results of the extended sliding study reinforce the previous conclusion that sliding distance (mechanical history) is the primary factor in establishing the force limiting boundary layer friction. General friction value under the extended sliding confirm those observed in previous orbital and the related ground test studies.

Hammel, R. L.↗

Effect of Moisture and Feedstock Variability on the Rheological Behavior of Corn Stover Particles

Continuous feeding, processing, and handling of biomass powders is pivotal to the economic viability of integrated biorefineries. However, current challenges associated with the operational reliability of bulk solids handling and transport greatly impact the process economics and ultimately the widespread commercialization of integrated biorefineries. In this work, we examine the effect of moisture and feedstock variability on the flow behavior of corn stover biomass particles. The total flow energy, compressibility, shear properties, and wall friction angles were measured for corn stover samples A and B containing 0%, 15%, 25%, 50%, and 75% (mass fraction) moisture contents using a FT4 powder rheometer. In general, the flowability of both A and B was reduced when moisture was present as indicated by the stability and variable flow rate, compressibility, and shear tests. The 15% moisture sample had the highest flow energy, revealing the interplay between the increased surface tension and looser packing both of which were caused by liquid bridging. The 75% moisture sample had the highest compressibility and the lowest flowability factor (ff c ). The trend in wall friction angle was found to be dependent upon the surface hydrophobicity of the wall material. The wall friction angle on the hydrophilic, stainless-steel surface increased with moisture and therefore poses additional handling challenges. On the other hand, the wall friction angle on the hydrophobic polymer surfaces were the lowest for samples with intermediate moisture contents. Sample B had greater bulk density, smaller compressibility, and greater flowability than the sample A , as suggested by the compressibility and shear tests. The wall friction angle of sample B was higher than or equal to that of sample A depending on both the type and the surface roughness of the wall material.

09 BIOMASS FUELS↗

Friction Force and Radiative Heat Exchange in a System of Two Parallel Plates in Relative Motion: Corollaries of the Levine–Polevoi–Rytov Theory

It has been shown that the fundamental results obtained in the works by Levine–Polevoi–Rytov (1980) and Rytov (1990) adequately describe the rate of radiative heat exchange and frictional force in a system of two thick parallel plates in relative motion, in full agreement with the results obtained by other authors later. A numerically calculated friction force for Drude metals turns out to be higher by a factor of 10{sup 7} than the early result obtained by Polevoi. In addition, the friction force significantly increases with increasing the conductivity of the plates or increasing the relaxation time of electrons with decreasing temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Acoustic Monitor for Particle Size and Bed Friction in a Carbonate Fluidized Bed at High Temperature - 18014

Previous work has shown that acoustic spectra of fluidized bed pressure fluctuations show many useful bed properties [1-3]. This current work further explores the use of acoustic monitors for an 18' diameter, 66-74'' height fluidized bed at >640 deg. C. This process denitrates and agglomerates an injected sodium/aluminum nitrate aqueous simulant and produces at steady-state a denitrated product of 200-300 micron sodium carbonate/aluminate particles. The fluidized bed shows characteristic acoustic resonances around 1-2 Hz in the FFT (Fast Fourier Transform) of pressure fluctuations for each of three taps at fluidized bed heights of 12'', 39'', and 58''. The acoustic resonance spectra depend on a bed friction that once calibrated, monitors the HMPD (harmonic mass mean particle diameter or Sauter mean diameter) along with other important bed properties. This fluidized bed operates at high temperature with an evolving HMPD that can be steady state with an appropriate superficial spatial velocity (SSV). The acoustic FFT integrated power spectrum, IPS, of pressure fluctuations represents the bed-friction damped RMS (root mean square) pressure fluctuations at each tap. The transition from a static to fluidized bed at each bed height occurs when the damped bed RMS pressure fluctuations are greater than the static head (the FFT zero Hz designated zero Hz proportional to FFT zero Hz) at that bed height. A bed will de-fluidize and become static at a bed height when bed friction completely dampens the RMS pressure fluctuations, which occurs for decreasing particle size among other factors. The ratio IPS/zero Hz then provides a continuous monitor of bed friction damping as well as particle size as the HMPD. Since HMPD and bed friction damping are both very important parameters for fluidized particle beds, the acoustic HMPD and bed friction damping both provide very useful monitors for fluidized bed operation. Such acoustic monitors have shown that they are especially sensitive to the presence of very fine particles in the bed of less than 50 microns diameter. Acoustic monitors for particle size and bed friction damping will be very useful in any fluidized bed, especially fluidized beds where particle size changes. The fluidized bed friction damping depends on many other bed properties besides particle size such as bed height, density, SSV, void fraction, gas viscosity, and fluidization scheme and so acoustic bed friction should also be useful for monitoring other bed properties besides particle size. In fact, the change in the static bed friction slope with SSV upon fluidization follows the Ergun function and reveals a minimum fluidization velocity for each HMPD. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Gimbal Bearing Friction in the SLS Core Stage Thrust Vector Control System

The Space Launch System (SLS) Core Stage Thrust Vector Control (TVC) system is comprised of eight mechanical feedback Shuttle heritage Type III TVC actuators that vector the four Shuttle heritage RS-25 engines about a Shuttle heritage gimbal block/bearing. The MSFC Controls community has long regarded gimbal friction to be a negligible effect on the overall control of gimbaled RS-25 engines. This is corroborated by Space Shuttle test and flight data that does not appear to show degraded effects, nor limit cycling at the end of the shuttle flight. For this reason, friction was not expected to be a driving factor of performance and control of the reused RS-25 engines aboard the SLS. However, after test data showed a large shift in frequency behavior and a highly damped step-response in the time series, there was further investigation into what could have caused this behavior. Heritage friction models used in previous gimbal and ball bearings were evaluated such as Coulomb, Dahl and LuGre, but the single degree of freedom friction models alone were not enough to explain the behavior and shifts seen in the test data. This paper presents the additional findings and modeling efforts regarding friction on the RS-25 engines. Using the Two Actuator Operational Simulation (TAOS), the difference from modeling separate friction degrees of freedom to coupled degrees of freedom was investigated to deduce the effects of one axis’s movement on the other. Next, due to the vibration environment, a modified LuGre model has been proposed that adds an additional term to decrease the friction coefficient at low engine velocity amplitudes. Lastly, the addition of the stiffness in each half of the gimbal bearing has increased modeling fidelity by also adding the effect on the gimbal bearing bending in compliance to both the friction torque on the surface of the gimbal bearing and the actuator force that is forcing the engine in a specified direction. Through these effects, the time and frequency domain behavior seen in test can be characterized accurately.

Friction↗

Gimbal Bearing Friction in the SLS Core Stage Thrust Vector Control System

The Space Launch System (SLS) Core Stage Thrust Vector Control (TVC) system is comprised of eight mechanical feedback Shuttle heritage Type III TVC actuators that vector the four Shuttle heritage RS-25 engines about a Shuttle heritage gimbal block/bearing. The MSFC Controls community has long regarded gimbal friction to be a negligible effect on the overall control of gimbaled RS-25 engines. This is corroborated by Space Shuttle test and flight data that does not appear to show degraded effects, nor limit cycling at the end of the shuttle flight. For this reason, friction was not expected to be a driving factor of performance and control of the reused RS-25 engines aboard the SLS. However, after test data showed a large shift in frequency behavior and a highly damped step-response in the time series, there was further investigation into what could have caused this behavior. Heritage friction models used in previous gimbal and ball bearings were evaluated such as Coulomb, Dahl and LuGre, but the single degree of freedom friction models alone were not enough to explain the behavior and shifts seen in the test data. This paper presents the additional findings and modeling efforts regarding friction on the RS-25 engines. Using the Two Actuator Operational Simulation (TAOS), the difference from modeling separate friction degrees of freedom to coupled degrees of freedom was investigated to deduce the effects of one axis’s movement on the other. Next, due to the vibration environment, a modified LuGre model has been proposed that adds an additional term to decrease the friction coefficient at low engine velocity amplitudes. Lastly, the addition of the stiffness in each half of the gimbal bearing has increased modeling fidelity by also adding the effect on the gimbal bearing bending in compliance to both the friction torque on the surface of the gimbal bearing and the actuator force that is forcing the engine in a specified direction. Through these effects, the time and frequency domain behavior seen in test can be characterized accurately.

Friction↗

In-flight boundary-layer measurements on a hollow cylinder at a Mach number of 3.0

Skin temperatures, shear forces, surface static pressures, boundary layer pitot pressures, and boundary layer total temperatures were measured on the external surface of a hollow cylinder that was 3.04 meters long and 0.437 meter in diameter and was mounted beneath the fuselage of the YF-12A airplane. The data were obtained at a nominal free stream Mach number of 3.0 (a local Mach number of 2.9) and at wall to recovery temperature ratios of 0.66 to 0.91. The local Reynolds number had a nominal value of 4,300,000 per meter. Heat transfer coefficients and skin friction coefficients were derived from skin temperature time histories and shear force measurements, respectively. In addition, boundary layer velocity profiles were derived from pitot pressure measurements, and a Reynolds analogy factor was obtained from the heat transfer and skin friction measurements. The measured data are compared with several boundary layer prediction methods.

Quinn, R. D.↗

Effect of frictional heating on brake materials

An exploratory study of the properties of aircraft brake materials was made to determine ways of improving friction and wear behavior while minimizing surface temperatures. It is found that frictional variation at high temperature involves material softening and metal transfer, formation of oxides, and surface melting. The choice of proper materials to combat these effects is discussed. Minimum surface temperatures are found to result from use of materials with large density-specific heat and density-specific heat-conductivity factors, use of a higher load-lower friction system, and maximization of the contact area. Some useful trade-off criteria for the size of brake disks against weight considerations are suggested. Additional information on material behavior and peak braking temperatures was gathered from an inspection of used brake pads and rotor disks.

Ho, T.-L.↗

BISON fuel performance modeling optimization for experiment X447 and X447A using axial swelling and cladding strain measurements

With the recent need to qualify new reactor designs such as the Versatile Test Reactor (VTR), fuel performance calculations need to be performed to determine safety criteria of the proposed designs. In order to validate the fuel performance results obtained by a fuel performance code, BISON, for new reactor designs, legacy fuel from EBR-II and FFTF MFF with Post -Irradiation Examination (PIE) data need to be used as validation cases to benchmark models. Here in this work, BISON has been paired with the Fuels Irradiation & Physics Database (FIPD) and IFR Materials Information System (IMIS) to supply PIE data for comparison with simulations of EBR-II experiments X447/X447A. X447/X447A were assessed by implementing models for Fuel Cladding Chemical Interaction (FCCI) within BISON and optimizing the friction coefficient between the fuel surface and the cladding, the anisotropic swelling factor, and the HT9 first thermal creep scalar (which scales the first term in the HT9 creep equation) to best match the PIE axial fuel swelling height and cladding profilometry for all pins in X447/X447A. The optimal values were found using a generic algorithm developed to select different values for the three parameters until end criteria was met and error couldn’t be reduced further. The BISON-simulated cladding profilometry was evaluated using Standard Error of the Estimate (SEE) to account for the profile shape of the cladding profilometry. Optimal values for the friction coefficient, anisotropic fuel swelling factor, and HT9 first thermal creep scalar were found to best fit the BISON simulation results to the PIE measurements found in IMIS and FIPD. Improvements to current models are suggested to account for the underprediction of fuel swelling at low burnups and the overprediction of fuel swelling at higher burnups observed for the axial fuel swelling height. Although two pins in EBR-II X447/X447A (DP70 and DP75) were known to fail due to FCCI, none of the pins simulated in BISON reached a cumulative damage fraction (CDF) above 0.008 with FCCI correlations coupled in the BISON simulations. The error estimate generated for all pins in X447/X447A using optimal values was 209 µm, which is deemed acceptable.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗