Search NASA⌕ Search

SEARCH · Search NASA

Results for “Finite Element Model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Modal Test and Analysis Correlation of Wind Tunnel Blades for the National Transonic Facility

NASA has a significant maintenance challenge with the aging wind tunnel infrastructure across the agency . Wind tunnel blades, such as the ones in the National Transonic Facility at NASA Langley Research Center, have been subjected to damage from impacts and fatigue. Accurate analytical models of these blades are necessary to either recertify replacement blades to be built or for redesign of these blades. In this paper an upgraded finite element model of these wind tunnel blades with the capability of representing damage is presented. An eigenvalue analysis of the structural model is performed, and the boundary conditions are adjusted to simulate the natural frequencies obtained by experimental testing of a set of twenty five blades in 1992. Additional numerical studies of the effect of delamination damage on the natural frequencies of the blade are conducted using the tuned finite element model.

wind tunnel↗
NASA NTRS1992

Postseismic deformation and stress diffusion due to viscoelasticity and comments on the modified Elsasser model

Finite element techniques have been used to investigate the far-field deformation and stress changes due to asthenospheric viscoelastic relaxation following a dip-slip earthquake. The diffusion of extensional stress toward the subduction zone following a thrust earthquake on land is qualitatively consistent with the modified Elsasser model as proposed by Rydelek and Sacks (1988, 1990) to explain the coupled occurrence of land and sea earthquakes near Japan. However, the magnitude of the diffusing tensional signal is significantly smaller. The nominal model consists of a partially faulted elastic lithosphere overlying a viscoelastic substrate. Other models consider thin channel flow, rupturing of the entire elastic lithosphere, and changes in the depth of faulting. While some of these changes have significant impact on the magnitude and spatial features of the stress and deformation field, the far-field stress remains small. Numerical experiments demonstrate that the assumptions of the modified Elsasser model accentuate uniaxial deformation. When these assumptions are replicated in the finite element calculations, reasonable agreement between the models is achieved.

Cohen, Steven C.↗
NASA NTRS1993

Three-dimensional finite element progressive failure analysis of composite laminates under axial extension

A three-dimensional (3D) progressive failure algorithm is developed, where the layerwise laminate theory (LWLT) of Reddy is used for kinematic description. The finite element model based on the layerwise theory predicts both inplane and interlaminar stresses with the same accuracy as that of a conventional 3D finite element model and provides a convenient format for modeling the 3D stress fields in composite laminates. A parametric study is conducted to investigate the effect of out-of-plane material properties, 3D stiffness reduction methods, and boundary conditions on the failure loads and strains of a composite laminate under axial extension. The results indicate that different parameters have a different degree of influence on the failure loads and strains. The predictive ability of various phenomenological failure criteria is evaluated in the light of experimental results available in the literature, and the predictions of the LWLT are compared with those of the first-order shear deformation theory. It is concluded that a 3D stress analysis is necessary to predict accurately the failure behavior of composite laminates.

Reddy, Yeruva S.↗
NASA NTRSDate not supplied

Developing Procedures to Implement Geometric Imperfections Beyond Right Circular Cylindrical Shells in Finite Element Method Models

Analysis of aerospace structures is frequently conducted using nominal dimensions and frequently assumes ideal conditions in loading, contact, constraints, et cetera. Off-nominal dimensions and nonideal conditions, however, are present in all structures. These are the result of widely ranging causes from coefficient of thermal expansion mismatches, manufacturing tooling anomalies, to assembly procedures that inadvertently alter the structure. Specifically, geometric imperfections can have potentially significant influence on the response of a structural test article observed in an experiment versus the response given by a numerical simulation. The Python Tool for Implementing Geometric Imperfections in Reduced Structures (Py_TIGIRS) was previously presented as a set of Python scripts to calculate and implement as-manufactured geometric midsurface and thickness imperfections into finite element method (FEM) shell models of nominally right circular cylinders. By taking advantage of the simple shape of a right circular cylinder, interpolations of the measured data points were able to be performed along directions that aligned to the cylindrical coordinate system axes of the entire structure. By taking advantage of the shell representation of the real structure as opposed to modeling using a continuum representation, the thickness variation was able to be implemented by shell section definitions instead of having to modify the position of multiple nodes in the thickness direction. Py_TIGIRS is a useful tool that established a procedural example on how to implement geometric imperfections in right circular cylindrical shell structures. Three new procedures, each expanded from concepts established in Py_TIGIRS, are proposed for various test-article designs and are intended to broaden the range of structures that can be modeled with measured geometric imperfections in the structural analysis community. Each test-article design introduces new challenges to successfully implement geometric imperfections into a FEM model. The first test-article design consists of a carbon fiber reinforced polymer square plate with a hat-shaped stiffener co-cured on one side. This test-article design was for a novel seven-point bend test that was also previously presented. Manufacturing and cure-cycle imperfections are observed using digital image correlation (DIC) techniques. As thermal expansion coefficient mismatches between the plate and stiffener materials were anticipated, a thermal analysis study with continuum shell and solid elements was conducted to capture the global shape observed prior to testing. The second test-article design is of a similar hat-stiffened plate configuration, but with a side length ratio near 3:1 with elongation in the stiffener direction. The test article was used to characterize the response to uniaxial compressive loading in the direction of the stiffener. Due to differing manufacturing steps, a thermal analysis like the one developed for the seven-point bend configuration was unable to mimic the observed geometric imperfections. Instead, a strategy based on applying deformations directly to the structure during analysis was developed for continuum shell and solid element representation of a stiffened panel.

Geometric imperfections↗
NASA NTRS1991

Simulation of the Space Station strut-out condition

A method is presented for reanalyzing a truss structure when one of the truss elements (struts) has failed. The method uses a modal model of the nominal structure coupled with a residual flexibility term to predict the effect of the failed strut without resolving the finite element model. By implementing the method as part of the transient simulation, it is feasible to consider a large number of potential strut failures with a minimum amount of extra effort. Preliminary application of the method to the Space Station indicates excellent agreement with results based on modifying and resolving the finite element model.

Blelloch, Paul A.↗
NASA NTRS1991

On the modeling of delamination in thick composites

The layerwise laminate theory of Reddy (1989) is used to develop a layerwise, two-dimensional, displacement-based, finite element model of laminated composite plates that provides a convenient format for modeling multiple delaminations. The resulting layerwise model is capable of computing interlaminar stresses, free edge effects, and energy release rates with the same accuracy as a conventional 3D finite element model. Although the total degrees of freedom are comparable in both models, the layerwise, two-dimensional format allows faster computation of the element stiffness matrices. Two example problems are provided to illustrate the accuracy of the present model in computing interlaminar stresses and energy release rates for laminates in bending and extension.

Robbins, D. H.↗
NASA NTRS1998

Model-Trained Neural Networks and Electronic Holography Demonstrated to Detect Damage in Blades

Detect Damage in Blades Electronic holography can show damaged regions in fan blades at 30 frames/sec. The electronic holograms are transformed by finite-element-model-trained artificial neural networks to visualize the damage. The trained neural networks are linked with video and graphics to visualize the bending-induced strain distribution, which is very sensitive to damage. By contrast, it is very difficult to detect damage by viewing the raw, speckled, characteristic fringe patterns. For neural-network visualization of damage, 2 frames or 2 fields are used, rather than the 12 frames normally used to compute the displacement distribution from electronic holograms. At the NASA Lewis Research Center, finite element models are used to compute displacement and strain distributions for the vibration modes of undamaged and cracked blades. A model of electronic time-averaged holography is used to transform the displacement distributions into finite-element-resolution characteristic fringe patterns. Then, a feedforward neural network is trained with the fringe-pattern/strain-pattern pairs, and the neural network, electronic holography, and video are implemented on a workstation. Now that the neural networks have been tested successfully at 30 frames/sec on undamaged and cracked cantilevers, the electronic holography and neural-network processing are being adapted for onsite damage inspection of twisted fan blades and rotormounted blades. Our conclusion is that model-trained neural nets are effective when they are trained with good models whose application is well understood. This work supports the aeromechanical testing portion of the Advanced Subsonic Technology Project.

Decker, Arthur J.↗
NASA NTRS1992

Global/local analysis of laminated composite plates using variable kinematic finite elements

A finite element modeling methodology is developed for the hierarchical, global/local analysis of laminated composite plates. The method incorporates a new variable kinematics, displacement-based, finite element that is developed using a multiple assumed displacement field approach. The variable kinematic elements provide a great degree of flexibility in defining the transverse (through thickness) variation of the assumed displacement field. The resulting finite element model permits different subregions of the computational domain to be described by different mathematical models. Enforcing displacement continuity along subregion boundaries requires only the specification of certain homogeneous essential boundary conditions, thus avoiding the inconvenience of multi-point constraints, penalty function methods, or special transition elements.

Robbins, D. H., Jr.↗
NASA NTRS1993

Design, analysis, and fabrication of a pressure box test fixture for tension damage tolerance testing of curved fuselage panels

A pressure box test fixture was designed and fabricated to evaluate the effects of internal pressure, biaxial tension loads, curvature, and damage on the fracture response of composite fuselage structure. Previous work in composite fuselage tension damage tolerance, performed during NASA contract NAS1-17740, evaluated the above effects on unstiffened panels only. This work extends the tension damage tolerance testing to curved stiffened fuselage crown structure that contains longitudinal stringers and circumferential frame elements. The pressure box fixture was designed to apply internal pressure up to 20 psi, and axial tension loads up to 5000 lb/in, either separately or simultaneously. A NASTRAN finite element model of the pressure box fixture and composite stiffened panel was used to help design the test fixture, and was compared to a finite element model of a full composite stiffened fuselage shell. This was done to ensure that the test panel was loaded in a similar way to a panel in the full fuselage shell, and that the fixture and its attachment plates did not adversely affect the panel.

Smith, P. J.↗
NASA NTRS1997

Nonlinear Dynamic Behavior in the Cassini Spacecraft Modal Survey

In October 1997, the 6-ton robotic spacecraft, Cassini, will lift off from Cape Canaveral atop a Titan IV B rocket, beginning a 7-year journey to Saturn. Upon completion of that voyage, Cassini will send the Huygens probe into the atmosphere of Saturn's largest moon, Titan. Cassini will then spend years studying Saturn's vast realm of rings, icy moons, and magnetic fields. The size and complexity of this endeavor mandates the involvement of many organizations. The Jet Propulsion Laboratory (JPL) manages the project for NASA and is responsible for the spacecraft design, development, and assembly. The NASA Lewis Research Center is the launch system integrator. As is typical for such a spacecraft, a test-verified finite element model is required for loads analysis. JPL had responsibility for the Cassini modal survey and the development of the spacecraft test-verified finite element model. Test verification is a complex and sometimes subjective process. Because of this, NASA Lewis independently verified and validated the Cassini spacecraft modal survey.

Carney, Kelly S.↗
NASA NTRS1984

Mathematical synthesization of complex structures

A mathematical synthesization approach for rapidly modeling and analyzing complex structures comprised of hundreds or thousands of repeating individual structural members, interconnecting hardware, and other components was described. The techniques are applicable to any structure with repeating structural members. The capabilities are embodied within the Interactive Design and Evaluation of Advanced Spacecraft (IDEAS) computer-aided design system. IDEAS has a full range of integrated spacecraft modeling, design, analysis, performance, and cost estimating capabilities which include about 40 technical program and executive, data base, and file management systems. With IDEAS, a single user at an interactive terminal can create, design, analyze, and conduct parametric studies of Earth orbiting spacecraft in a timely, cost-efficient manner. The system is particularly useful in the conceptual design phases of advanced space missions when a multiplicity of concepts must be evaluated. The IDEAS interactive finite-element modeling capabilities are discussed. The mathematical synthesization programs were structured not only to provide a detailed finite-element model of the structure but also to automatically perform the many auxiliary computations needed to analyze the spacecraft in its orbital operational environment.

Garrett, L. B.↗
NASA NTRS2016

Revisiting of Multiscale Static Analysis of Notched Laminates Using the Generalized Method of Cells

Composite material systems generally exhibit a range of behavior on different length scales (from constituent level to macro); therefore, a multiscale framework is beneficial for the design and engineering of these material systems. The complex nature of the observed composite failure during experiments suggests the need for a three-dimensional (3D) multiscale model to attain a reliable prediction. However, the size of a multiscale three-dimensional finite element model can become prohibitively large and computationally costly. Two-dimensional (2D) models are preferred due to computational efficiency, especially if many different configurations have to be analyzed for an in-depth damage tolerance and durability design study. In this study, various 2D and 3D multiscale analyses will be employed to conduct a detailed investigation into the tensile failure of a given multidirectional, notched carbon fiber reinforced polymer laminate. Threedimensional finite element analysis is typically considered more accurate than a 2D finite element model, as compared with experiments. Nevertheless, in the absence of adequate mesh refinement, large differences may be observed between a 2D and 3D analysis, especially for a shear-dominated layup. This observed difference has not been widely addressed in previous literature and is the main focus of this paper.

Materials Engineering↗
NASA NTRS1977

Solid propellant rocket motor internal ballistics performance variation analysis, phase 3

Results of research aimed at improving the predictability of off nominal internal ballistics performance of solid propellant rocket motors (SRMs) including thrust imbalance between two SRMs firing in parallel are reported. The potential effects of nozzle throat erosion on internal ballistic performance were studied and a propellant burning rate low postulated. The propellant burning rate model when coupled with the grain deformation model permits an excellent match between theoretical results and test data for the Titan IIIC, TU455.02, and the first Space Shuttle SRM (DM-1). Analysis of star grain deformation using an experimental model and a finite element model shows the star grain deformation effects for the Space Shuttle to be small in comparison to those of the circular perforated grain. An alternative technique was developed for predicting thrust imbalance without recourse to the Monte Carlo computer program. A scaling relationship used to relate theoretical results to test results may be applied to the alternative technique of predicting thrust imbalance or to the Monte Carlo evaluation. Extended investigation into the effect of strain rate on propellant burning rate leads to the conclusion that the thermoelastic effect is generally negligible for both steadily increasing pressure loads and oscillatory loads.

Sforzini, R. H.↗
NASA NTRS1984

Space structure vibration modes: How many exist? Which ones are important?

This report attempts to shed some light on the two issues raised in the title, namely, how many vibration modes does a real structure have, and which of these modes are important? The surprise-free answers to these two questions are, respectively, an infinite number and the first several modes. The author argues that the absurd subspace (all but the first billion modes) is not a strength of continuum modeling, but, in fact, a weakness. Partial differential equations are not real structures, only mathematical models. This note also explains (1) that the PDE model and the finite element model are, in fact, the same model, the latter being a numerical method for dealing with the former, (2) that modes may be selected on dynamical grounds other than frequency alone, and (3) that long slender rods are useful as primitive cases but dangerous to extrapolate from.

Hughes, P. C.↗
NASA NTRS1987

Evaluation of on-line pulse control for vibration suppression in flexible spacecraft

On-line pulse control for vibration suppression in a flexible spacecraft was evaluated. A continuous beam vs. a truss was modeled. A linear finite element model was used to determine the truss characteristics. Control issues outlined are ED pulse actuator development, pseudo pulse algorithm development, and large nonlinear simulation problems.

Bekey, G. A.↗
NASA NTRS1991

Structural representation for analysis of a controlled structure

The purpose was to determine what reduced order structural representation is most appropriate for coupling with a control system. The goal was to choose a reduced order structural model which retains as closely as possible the characteristics of the closed loop model with a full order structural representation. By characteristics of the closed loop model, it is meant that the closed loop eigenvalues and the closed loop transfer functions from commands to loads and from commands to response. This process does not address the accuracy of the full order model (usually a finite element model) but only the loss of accuracy associated with reducing th model. For the purposes of this study, only collocated sensors and actuators are examined. The choice of a structural representation for noncollocated sensors and actuators is not so clear.

Blelloch, Paul A.↗
NASA NTRS2001

Corner Wrinkling at a Square Membrane Due to Symmetric Mechanical Loads

Thin-film membrane structures are under consideration for use in many future gossamer spacecraft systems. Examples include sunshields for large aperture telescopes, solar sails, and membrane optics. The development of capabilities for testing and analyzing pre-tensioned, thin film membrane structures is an important and challenging aspect of gossamer spacecraft technology development. This paper presents results from experimental and computational studies performed to characterize the wrinkling behavior of thin-fi[m membranes under mechanical loading. The test article is a 500 mm square membrane subjected to symmetric comer loads. Data is presented for loads ranging from 0.49 N to 4.91 N. The experimental results show that as the load increases the number of wrinkles increases, while the wrinkle amplitude decreases. The computational model uses a finite element implementation of Stein-Hedgepeth membrane wrinkling theory to predict the behavior of the membrane. Comparisons were made with experimental results for the wrinkle angle and wrinkled region. There was reasonably good agreement between the measured wrinkle angle and the predicted directions of the major principle stresses. The shape of the wrinkle region predicted by the finite element model matches that observed in the experiments; however, the size of the predicted region is smaller than that determined in the experiments.

Blandino, Joseph R.↗
NASA NTRS1999

Creation of Anatomically Accurate Computer-Aided Design (CAD) Solid Models from Medical Images

Most surgical instrumentation and implants used in the world today are designed with sophisticated Computer-Aided Design (CAD)/Computer-Aided Manufacturing (CAM) software. This software automates the mechanical development of a product from its conceptual design through manufacturing. CAD software also provides a means of manipulating solid models prior to Finite Element Modeling (FEM). Few surgical products are designed in conjunction with accurate CAD models of human anatomy because of the difficulty with which these models are created. We have developed a novel technique that creates anatomically accurate, patient specific CAD solids from medical images in a matter of minutes.

Stewart, John E.↗