Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flow Measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Particle and flow field measurements by laser holography

Holograms make transmission recordings of aerodynamic events which are real-illuminated with ground-glass light diffusers and with no requirements for precision. The three-dimensional interferograms can be recorded by stored-beam, double-exposure, and double-plate techniques. Weak traveling shock waves, generated by rotating blade rows of an aircraft fan compressor, can be visualized by rapid double-exposure holograms recorded with a ruby laser. The same laser technique can also determine flow velocities from holograms of small flow-entrained particles. Particles larger than one-quarter millimeter are recorded under rear diffuse illumination conditions. Smaller particles can be recorded by their own forward scattering of laser light through the sensitivity of the holographic process for weak signals. Since the holographic apparatus can be path-matched, both particle and flow interferograms can be recorded with lasers of short coherence length.

Wuerker, R. F.↗
NASA NTRS2020

Europa Clipper Passive Thermal Control Valve Test and Analysis

Europa Clipper spacecraft utilizes passive thermal control valves (TCV) in an active thermal control system to maintain spacecraft component temperatures within their allowable limits. The single-phase mechanically pumped fluid loop recovers heat from the electronics and uses it to maintain propulsion system warm. When excess heat is dissipated the mixing valves direct the fluid to the radiator to reject this additional heat. The loop uses two mixing TCVs placed in series to modulate fluid flow and heat rejection rate from the radiator. This paper describes the thermal and hydraulic test results for Europa Clipper engineering model (EM) mixing valves. For the first time two heritage mixing valves previously developed for the Mars Science Laboratory (MSL) were placed in series to modulate flow to the radiator from 0.1% to 95% of full flow between temperature range of 4 oC to 24 oC. Individually, each mixing valve was able to modulate the flow from 2% to 96% of full flow between the temperatures of 4 oC and 24 oC. Pressure drop was measured between 1.5 to 3 psid depending on the temperature of the mixed fluid and the opening fraction of the valves. A methodology was developed, tested, and validated to adjust the setpoints with an accuracy of 0.1 oC. The measured flow splits were corrected for the effects of impedance due to the flow meters used to measure the flow rates. Finally, flow rate to the radiator increased linearly as a function of mixed temperature for individual valves, while it increased parabolically with temperature when two mixing valves were placed in series.

Mastropietro, AJ↗
NASA NTRS1982

HOST instrumentation R and D program overview

The turbine hot-section technology (HOST) Instrumentation R&D program focuses on two main classes of instrumentation: (1) those that characterizes the environment around the turbine engine components, which include gas flows measurement, gas temperatures, and heat fluxes; (2) to characterize the effect of the environment on the turbine engine components, which include strain measurements and an optical system to structural responses such as cracking, buckling, spalling, carbon buildup. The HOST Instrumentation R&D program concentrates on the critical measurements that can not be made by commercially available instruments or with instruments that are already in development. The measurements of strain and gas flow are emphasized, these measurements are extremely critical to the success of the HOST program and the HOST requirements differ from the current state of the art by a considerable margin.

Wenger, N. C.↗
NASA NTRS1979

Measurements of flow phenomena induced by suction through perforated and partially plugged surfaces

Efforts were directed towards completing construction of the windtunnel test section, assembling instrumentation, programming the data acquisition and reduction system, adjusting the streamwise pressure gradient of the test section, calibrating the hot-wire anemometer probe, and constructing and testing a smoke generator. The test section was installed in the wind tunnel and is completely operational. The streamwise pressure gradient was adjusted to be nominally zero at a free-stream velocity of 3.05 m/s (10 ft/s). This was accomplished by adjusting the upper wall of the test section to be slightly divergent. The change in static pressure between any two streamwise locations in the test section was less than one percent of the free-stream dynamic pressure. A suitable means was found for accurately calibrating the hot-wire probe which is used to measure boundary-layer velocity profiles and fluctuating velocities.

Wilkinson, S. P.↗
DOE OSTI2021

Evaluating the Influence of Rotor-Casing Eccentricity on Turbine Efficiency Including Time-Resolved Flow Field Measurements

Abstract The clearance that exists between the casing and turbine blade tips is one of the key drivers of efficiency in gas turbine engines. For this reason, engine manufacturers utilize precise manufacturing techniques and may use clearance control systems to minimize tip clearances to reduce associated losses. Despite these efforts, turbines typically exhibit some nominal casing ovality or rotor-casing eccentricity, and changes to blade tip clearance during operation commonly occur due to thermal and mechanical stresses. The present study investigates non-axisymmetric tip clearance effects by creating a rotor-casing eccentricity in a one-stage axial test turbine operating in a continuous-duration mode at engine-relevant conditions with engine representative hardware. A magnetic levitation bearing system was leveraged to move the turbine shaft to vary the rotor-casing eccentricity without test section disassembly. The results of this study indicate that rotor-casing eccentricity does not affect overall turbine efficiency over the range that was tested, but does locally influence efficiency and the rotor exit flow field. Comparisons of flow angle and secondary flow kinetic energy (SKE) agreed with previous studies and existing analytical methods, respectively. Collectively, these results indicate that tip clearance can be studied locally on an eccentric rotor.

Engineering↗
DOE OSTI2020

Geophysical borehole logging data of wells ER-GLS1, ER-GUM1, ER-PLM7, and ER-PLM8 at the East River Watershed, Colorado

The purpose of this data set is to provide a means of characterizing the bedrock variability both within a single borehole location and across the East River Watershed. The East River is part of the Watershed Function Scientific Focus Area (WFSFA) located in the Upper Colorado River Basin, United States, and all boreholes are located within Mancos shale bedrock. The data set contains geophysical borehole logging data acquired in October 2018 in boreholes ER-GUM1 (East River- Gothic Upper Montane Borehole #1) and ER-GLS1 (East River- Gothic Lower Subalpine Borehole #1), and acquired in October 2019 in boreholes ER-PLM7 (East River- Pumphouse Lower Montane Borehole #7) and ER-PLM8 (East River- Pumphouse Lower Montane Borehole #8). It contains depth, natural gamma ray emission, spectral gamma ray emission(Th, K, U), magnetic susceptibility, fluid temperature and electrical conductivity, electromagnetic (EM) induction derived rock electrical resistivity, heat pulse and spinner flow measurements to estimate groundwater flow, and Nuclear Magnetic Resonance (NMR) derived water content and hydraulic conductivity. Data for each borehole are provided as comma delimited text files. For each borehole accurate location information is provided (based on RTK GPS (Real Time Kinematic Global Positioning System) surveying). Borehole logging data were acquired using Mount Sopris borehole tools, and Vista Clara Javelin for NMR data.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1973

Research on the sonic boom problem. Part 2: Flow field measurement in wind tunnel and calculation of second order F-function

An experimental investigation has been carried out in a wind tunnel to test some of the results of Landahl's second order theory. The slender models consisted of a parabolic spindle, tested at M = 3, and a wing body configuration, suggested by Ferri, and tested at M = 2.7. The theory indicates that shock position and strength at an arbitrary distance can be calculated by means of near field measurements. The results show that this method is an appropriate one for simple bodies and for bodies with complicated geometries as well.

Landahl, M.↗
NASA NTRS1976

Review of measurement and testing problems

Good instrumentation was required to obtain reliable and repeatable baseline data. Problems that were encountered in developing such a total system were: (1) accurate airflow measurement, (2) precise fuel flow measurement, and (3) the instrumentation used for pollutant measurement was susceptible to frequent malfunctions. Span gas quality had a significant effect on emissions test results. The Spindt method was used in the piston aircraft emissions program. The Spindt method provided a comparative computational procedure for fuel/air ratio based on measured emissions concentrations.

Source record↗
NASA NTRS1978

Measurement of flow angle and mass flow rate in an unknown flow field using hot film and hot wire probes

A data reduction technique applicable to constant temperature hot film and hot wire probes is presented which is used to determine flow angle and mass flow rate in an unknown flow field over a wide range of flow conditions at supersonic and hypersonic velocities. The technique virtually eliminates the effect of Reynolds number on a probe's flow angle sensitivity. Methods for extrapolating a limited amount of mass flow rate calibration data to include the range of mass flow rate encountered in an experiment are also given. This technique has been applied to data obtained using a hot film probe during surveys in the leeside flow field of a space shuttle orbiter configuration.

Helms, V. T., III↗
NASA NTRS1983

Measuring Power Flow in Electric Vehicles

Instrument accommodates fast rise and fall times of waveforms characteristic of modern, efficient power controllers. Power meter multiplies analog signals proportional to voltage and current, and converts resulting signal to frequency. Two mechanical counters provided: one for charging, one for discharging.

Griffin, Daniel C., Jr↗
NASA NTRS1983

A holographic interferometry technique for measuring transonic flow near a rotor blade

A technique that uses holographic interferometry to record the first interferograms of the flow near a hovering transonic rotor blade is presented. A pulsed ruby laser is used to record interferograms of a 2 ft diam field of view near a rotor tip operating at a tip Mach number of 0.90. Several interferograms, recorded along planes perpendicular to the rotor's tip path plane at various azimuth angles around the flow, are presented. These interferograms yield quantitative information about shock structure and location, flow separation, and radiated noise that will help helicopter researchers understand the complexities of the flow around high speed rotor blades and thus improve performance and reduce noise.

Kittleson, J. K.↗